Sometimes audio works, sometimes not on apple tv

I'm using my iPad2 and AirPlay through My new ATV2 to watch movies and TV shows purchased through iTunes. My ATV2 is connected via HDMI to a Denon receiver, which in turn is connected to my HDTV via HDMI. I have two speakers set up from my receiver; (the TV speakers are muted).
Most of the time it all works flawlessly. But with some iTunes purchases, the audio disappears, or at least the dialogue. For example, I purchased a sample pack of The Office, 5 episodes. On all but one, there is no audio, other than opening and closing credits music, and the odd sound effect. Same for an episode of Law and Order I purchased. Ditto for the rental movie Dreamgirls.
My guess is that on some of the newer videos, I'm missing the extra audio channel. Or could it be something else?
All help appreciated, from a confused non-techie....

Try turning settings > audio & video > Dolby digital on/off.
You might also try changing the audio out setting.

Similar Messages

  • PC is showing realtk high definition audio working but not showing not plugged in

    computer is a hp pavillion a6763w desktop PC. 
    i had installed a ati video card and all worked perfectly for a while after updating the drivers for it my onboard sound went out. the sound would play through the hdmi output but no other output. i uninstalled video card and drivers and reverted back to old drivers. did a restore point. reset the bios to enable onboard sound. reinstalled drivers for onboard sound. tried installing a sound card and it was not recognized by the computer. but still PC is showing realtk high definition audio working but nothing plugged in when it is. also i have tries several different devices being plugged in and none of them worked. 

    Hi,
    When installing a discreet sound card, you should disable on board audio.
    With HDMI, you have to chose speakers or HDMI but not both. It's one or the other.
    What ATI video card are you using and did you upgrade your power supply?
    Did you go to www.realtek.com and download the latest audio drivers when using the on board audio?
    HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
    HP Photosmart Premium C309G, HP Photosmart 6520
    HP Touchpad, HP Chromebook 11
    Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
    Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
    Windows 7/8 UEFI/Legacy mode, MBR/GPT

  • I have audio working, but not the microphone on my toshiba satellite

    Hi there, I'm a newbie to the arch way, but I'm not a newbie to linux, however I'm pretty stumped with this one (I'm not used to having to look after everything, but I'm loving it!) I have a Toshiba Satellite C650D-10W, and it has a very annoying soundcard built into it. I have the sound working, thankfully, however I cannot get the inbuilt mic to function. Some info here:
    lspci:
    00:00.0 Host bridge: Advanced Micro Devices [AMD] RS780 Host Bridge Alternate
    00:01.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (int gfx)
    00:04.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 0)
    00:05.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 1)
    00:11.0 SATA controller: ATI Technologies Inc SB700/SB800 SATA Controller [AHCI mode]
    00:12.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller
    00:12.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller
    00:13.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller
    00:13.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller
    00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 41)
    00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) (rev 40)
    00:14.3 ISA bridge: ATI Technologies Inc SB700/SB800 LPC host controller (rev 40)
    00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge (rev 40)
    00:16.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller
    00:16.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller
    00:18.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration
    00:18.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map
    00:18.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller
    00:18.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control
    00:18.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control
    01:05.0 VGA compatible controller: ATI Technologies Inc M880G [Mobility Radeon HD 4200]
    02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01)
    08:00.0 Ethernet controller: Atheros Communications AR8152 v1.1 Fast Ethernet (rev c1)
    Dmesg:
    Initializing cgroup subsys cpuset
    Initializing cgroup subsys cpu
    Linux version 2.6.35-ARCH (tobias@T-POWA-LX) (gcc version 4.5.1 (GCC) ) #1 SMP PREEMPT Sat Oct 30 19:57:05 UTC 2010
    BIOS-provided physical RAM map:
    BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
    BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
    BIOS-e820: 0000000000100000 - 000000002e54a000 (usable)
    BIOS-e820: 000000002e54a000 - 000000002e74a000 (ACPI NVS)
    BIOS-e820: 000000002e74a000 - 000000002fd3f000 (usable)
    BIOS-e820: 000000002fd3f000 - 000000002fdbf000 (reserved)
    BIOS-e820: 000000002fdbf000 - 000000002febf000 (ACPI NVS)
    BIOS-e820: 000000002febf000 - 000000002fef7000 (ACPI data)
    BIOS-e820: 000000002fef7000 - 000000002ff00000 (usable)
    BIOS-e820: 00000000f8000000 - 00000000f9000000 (reserved)
    BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
    BIOS-e820: 00000000fec10000 - 00000000fec11000 (reserved)
    BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
    BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
    Notice: NX (Execute Disable) protection cannot be enabled: non-PAE kernel!
    DMI 2.6 present.
    e820 update range: 0000000000000000 - 0000000000001000 (usable) ==> (reserved)
    e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
    last_pfn = 0x2ff00 max_arch_pfn = 0x100000
    MTRR default type: uncachable
    MTRR fixed ranges enabled:
    00000-9FFFF write-back
    A0000-BFFFF uncachable
    C0000-FFFFF write-through
    MTRR variable ranges enabled:
    0 base 000000000000 mask FFFFE0000000 write-back
    1 base 000020000000 mask FFFFF0000000 write-back
    2 base 00002FEBE000 mask FFFFFFFFF000 uncachable
    3 base 0000FFE00000 mask FFFFFFE00000 write-protect
    4 disabled
    5 disabled
    6 disabled
    7 disabled
    x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    e820 update range: 0000000000002000 - 0000000000010000 (usable) ==> (reserved)
    Scanning 1 areas for low memory corruption
    modified physical RAM map:
    modified: 0000000000000000 - 0000000000001000 (reserved)
    modified: 0000000000001000 - 0000000000002000 (usable)
    modified: 0000000000002000 - 0000000000010000 (reserved)
    modified: 0000000000010000 - 000000000009fc00 (usable)
    modified: 000000000009fc00 - 00000000000a0000 (reserved)
    modified: 00000000000e0000 - 0000000000100000 (reserved)
    modified: 0000000000100000 - 000000002e54a000 (usable)
    modified: 000000002e54a000 - 000000002e74a000 (ACPI NVS)
    modified: 000000002e74a000 - 000000002fd3f000 (usable)
    modified: 000000002fd3f000 - 000000002fdbf000 (reserved)
    modified: 000000002fdbf000 - 000000002febf000 (ACPI NVS)
    modified: 000000002febf000 - 000000002fef7000 (ACPI data)
    modified: 000000002fef7000 - 000000002ff00000 (usable)
    modified: 00000000f8000000 - 00000000f9000000 (reserved)
    modified: 00000000fec00000 - 00000000fec01000 (reserved)
    modified: 00000000fec10000 - 00000000fec11000 (reserved)
    modified: 00000000fee00000 - 00000000fee01000 (reserved)
    modified: 00000000ffe00000 - 0000000100000000 (reserved)
    initial memory mapped : 0 - 01800000
    init_memory_mapping: 0000000000000000-000000002ff00000
    0000000000 - 0000400000 page 4k
    0000400000 - 002fc00000 page 2M
    002fc00000 - 002ff00000 page 4k
    kernel direct mapping tables up to 2ff00000 @ 15000-1a000
    RAMDISK: 2e3b5000 - 2e53a000
    ACPI: RSDP 000fe020 00024 (v02 TOSINV)
    ACPI: XSDT 2fef6120 0005C (v01 TOSINV TOSINV00 00000003 01000013)
    ACPI: FACP 2fef5000 000F4 (v04 TOSINV TOSINV00 00000003 MSFT 01000013)
    ACPI: DSDT 2fee6000 0BAEB (v01 TOSINV TOSINV00 F0000000 MSFT 01000013)
    ACPI: FACS 2fe9c000 00040
    ACPI: HPET 2fef4000 00038 (v01 TOSINV TOSINV00 00000001 MSFT 01000013)
    ACPI: APIC 2fef3000 00084 (v02 TOSINV TOSINV00 00000001 MSFT 01000013)
    ACPI: MCFG 2fef2000 0003C (v01 TOSINV TOSINV00 00000001 MSFT 01000013)
    ACPI: BOOT 2fee5000 00028 (v01 TOSINV TOSINV00 00000001 MSFT 01000013)
    ACPI: SLIC 2fee4000 00176 (v01 TOSINV TOSINV00 00000001 MSFT 01000013)
    ACPI: SSDT 2fee3000 001BD (v01 AMD POWERNOW 00000001 AMD 00000001)
    ACPI: Local APIC address 0xfee00000
    0MB HIGHMEM available.
    767MB LOWMEM available.
    mapped low ram: 0 - 2ff00000
    low ram: 0 - 2ff00000
    Zone PFN ranges:
    DMA 0x00000001 -> 0x00001000
    Normal 0x00001000 -> 0x0002ff00
    HighMem empty
    Movable zone start PFN for each node
    early_node_map[5] active PFN ranges
    0: 0x00000001 -> 0x00000002
    0: 0x00000010 -> 0x0000009f
    0: 0x00000100 -> 0x0002e54a
    0: 0x0002e74a -> 0x0002fd3f
    0: 0x0002fef7 -> 0x0002ff00
    On node 0 totalpages: 195288
    free_area_init_node: node 0, pgdat c1418ac0, node_mem_map c157d020
    DMA zone: 32 pages used for memmap
    DMA zone: 0 pages reserved
    DMA zone: 3952 pages, LIFO batch:0
    Normal zone: 1502 pages used for memmap
    Normal zone: 189802 pages, LIFO batch:31
    Using APIC driver default
    ACPI: PM-Timer IO Port: 0x408
    ACPI: Local APIC address 0xfee00000
    ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
    ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] disabled)
    ACPI: LAPIC (acpi_id[0x02] lapic_id[0x00] disabled)
    ACPI: LAPIC (acpi_id[0x03] lapic_id[0x00] disabled)
    ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
    ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
    ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
    ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
    ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
    IOAPIC[0]: apic_id 4, version 33, address 0xfec00000, GSI 0-23
    ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
    ACPI: IRQ0 used by override.
    ACPI: IRQ2 used by override.
    ACPI: IRQ9 used by override.
    Using ACPI (MADT) for SMP configuration information
    ACPI: HPET id: 0x1002a201 base: 0xfed00000
    SMP: Allowing 4 CPUs, 3 hotplug CPUs
    nr_irqs_gsi: 40
    early_res array is doubled to 64 at [16000 - 167ff]
    PM: Registered nosave memory: 0000000000002000 - 0000000000010000
    PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
    PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
    PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
    PM: Registered nosave memory: 000000002e54a000 - 000000002e74a000
    PM: Registered nosave memory: 000000002fd3f000 - 000000002fdbf000
    PM: Registered nosave memory: 000000002fdbf000 - 000000002febf000
    PM: Registered nosave memory: 000000002febf000 - 000000002fef7000
    Allocating PCI resources starting at 2ff00000 (gap: 2ff00000:c8100000)
    Booting paravirtualized kernel on bare hardware
    setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:4 nr_node_ids:1
    PERCPU: Embedded 14 pages/cpu @c1c00000 s34880 r0 d22464 u1048576
    pcpu-alloc: s34880 r0 d22464 u1048576 alloc=1*4194304
    pcpu-alloc: [0] 0 1 2 3
    Built 1 zonelists in Zone order, mobility grouping on. Total pages: 193754
    Kernel command line: root=/dev/disk/by-uuid/df51f9a3-a50d-4006-a220-7f2121cc9926 ro
    PID hash table entries: 4096 (order: 2, 16384 bytes)
    Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Initializing CPU#0
    allocated 3927020 bytes of page_cgroup
    please try 'cgroup_disable=memory' option if you don't want memory cgroups
    Subtract (53 early reservations)
    #1 [0000001000 - 0000002000] EX TRAMPOLINE
    #2 [0001000000 - 0001574184] TEXT DATA BSS
    #3 [002e3b5000 - 002e53a000] RAMDISK
    #4 [000009fc00 - 0000100000] BIOS reserved
    #5 [0001575000 - 000157b1bf] BRK
    #6 [0000010000 - 0000011000] TRAMPOLINE
    #7 [0000011000 - 0000015000] ACPI WAKEUP
    #8 [0000015000 - 0000016000] PGTABLE
    #9 [000157c000 - 000157d000] BOOTMEM
    #10 [000157d000 - 0001b7d000] BOOTMEM
    #11 [00015741c0 - 00015741c4] BOOTMEM
    #12 [0001574200 - 00015742c0] BOOTMEM
    #13 [00015742c0 - 0001574308] BOOTMEM
    #14 [0001b7d000 - 0001b80000] BOOTMEM
    #15 [0001574340 - 0001574365] BOOTMEM
    #16 [0001574380 - 00015743a7] BOOTMEM
    #17 [00015743c0 - 00015745b8] BOOTMEM
    #18 [00015745c0 - 0001574600] BOOTMEM
    #19 [0001574600 - 0001574640] BOOTMEM
    #20 [0001574640 - 0001574680] BOOTMEM
    #21 [0001574680 - 00015746c0] BOOTMEM
    #22 [00015746c0 - 0001574700] BOOTMEM
    #23 [0001574700 - 0001574740] BOOTMEM
    #24 [0001574740 - 0001574780] BOOTMEM
    #25 [0001574780 - 00015747c0] BOOTMEM
    #26 [00015747c0 - 0001574800] BOOTMEM
    #27 [0001574800 - 0001574840] BOOTMEM
    #28 [0001574840 - 0001574880] BOOTMEM
    #29 [0001574880 - 00015748c0] BOOTMEM
    #30 [00015748c0 - 0001574900] BOOTMEM
    #31 [0001574900 - 0001574940] BOOTMEM
    #32 [0001574940 - 0001574980] BOOTMEM
    #33 [0001574980 - 0001574990] BOOTMEM
    #34 [00015749c0 - 00015749d0] BOOTMEM
    #35 [0001574a00 - 0001574a10] BOOTMEM
    #36 [0001574a40 - 0001574a50] BOOTMEM
    #37 [0001574a80 - 0001574abf] BOOTMEM
    #38 [0001574ac0 - 0001574aff] BOOTMEM
    #39 [0001c00000 - 0001c0e000] BOOTMEM
    #40 [0001d00000 - 0001d0e000] BOOTMEM
    #41 [0001e00000 - 0001e0e000] BOOTMEM
    #42 [0001f00000 - 0001f0e000] BOOTMEM
    #43 [0001574b00 - 0001574b04] BOOTMEM
    #44 [0001574b40 - 0001574b44] BOOTMEM
    #45 [0001574b80 - 0001574b90] BOOTMEM
    #46 [0001574bc0 - 0001574bd0] BOOTMEM
    #47 [0001574c00 - 0001574ca0] BOOTMEM
    #48 [0001574cc0 - 0001574d08] BOOTMEM
    #49 [0001b80000 - 0001b84000] BOOTMEM
    #50 [0001c0e000 - 0001c8e000] BOOTMEM
    #51 [0001b84000 - 0001bc4000] BOOTMEM
    #52 [0001f0e000 - 00022ccbec] BOOTMEM
    Initializing HighMem for node 0 (00000000:00000000)
    Memory: 762948k/785408k available (2987k kernel code, 18204k reserved, 1237k data, 416k init, 0k highmem)
    virtual kernel memory layout:
    fixmap : 0xfff16000 - 0xfffff000 ( 932 kB)
    pkmap : 0xff800000 - 0xffc00000 (4096 kB)
    vmalloc : 0xf0700000 - 0xff7fe000 ( 240 MB)
    lowmem : 0xc0000000 - 0xeff00000 ( 767 MB)
    .init : 0xc1421000 - 0xc1489000 ( 416 kB)
    .data : 0xc12eac4c - 0xc1420200 (1237 kB)
    .text : 0xc1000000 - 0xc12eac4c (2987 kB)
    Checking if this processor honours the WP bit even in supervisor mode...Ok.
    SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
    Hierarchical RCU implementation.
    RCU-based detection of stalled CPUs is disabled.
    Verbose stalled-CPUs detection is disabled.
    NR_IRQS:512
    Console: colour VGA+ 80x25
    console [tty0] enabled
    hpet clockevent registered
    Fast TSC calibration using PIT
    Detected 2194.695 MHz processor.
    Calibrating delay loop (skipped), value calculated using timer frequency.. 4391.28 BogoMIPS (lpj=7315650)
    pid_max: default: 32768 minimum: 301
    Security Framework initialized
    Mount-cache hash table entries: 512
    Initializing cgroup subsys ns
    Initializing cgroup subsys cpuacct
    Initializing cgroup subsys memory
    Initializing cgroup subsys devices
    Initializing cgroup subsys freezer
    Initializing cgroup subsys net_cls
    Initializing cgroup subsys blkio
    mce: CPU supports 6 MCE banks
    using C1E aware idle routine
    Performance Events: AMD PMU driver.
    ... version: 0
    ... bit width: 48
    ... generic registers: 4
    ... value mask: 0000ffffffffffff
    ... max period: 00007fffffffffff
    ... fixed-purpose events: 0
    ... event mask: 000000000000000f
    SMP alternatives: switching to UP code
    ACPI: Core revision 20100428
    TOSHIBA Satellite detected - force copy of DSDT to local memory
    ACPI: Forced DSDT copy: length 0x0BAEB copied locally, original unmapped
    Enabling APIC mode: Flat. Using 1 I/O APICs
    ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    CPU0: AMD V120 Processor stepping 03
    System has AMD C1E enabled
    Switch to broadcast mode on CPU0
    Brought up 1 CPUs
    Total of 1 processors activated (4391.28 BogoMIPS).
    devtmpfs: initialized
    NET: Registered protocol family 16
    node 0 link 0: io port [0, ffffff]
    TOM: 0000000040000000 aka 1024M
    Fam 10h mmconf [f8000000, fbffffff]
    node 0 link 0: mmio [a0000, bffff]
    node 0 link 0: mmio [40000000, 4fffffff]
    node 0 link 0: mmio [50000000, 520fffff]
    node 0 link 0: mmio [52100000, 522fffff]
    node 0 link 0: mmio [52300000, f7ffffff]
    node 0 link 0: mmio [f8000000, fbffffff] ==> none
    node 0 link 0: mmio [fc000000, ff6fffff]
    bus: [00, 1f] on node 0 link 0
    bus: 00 index 0 [io 0x0000-0xffff]
    bus: 00 index 1 [mem 0x000a0000-0x000bffff]
    bus: 00 index 2 [mem 0x40000000-0xf7ffffff]
    bus: 00 index 3 [mem 0xfc000000-0xffffffff]
    ACPI: bus type pci registered
    PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
    PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
    PCI: MMCONFIG for 0000 [bus00-0f] at [mem 0xf8000000-0xf8ffffff] (base 0xf8000000) (size reduced!)
    PCI: Using MMCONFIG for extended config space
    PCI: Using configuration type 1 for base access
    bio: create slab <bio-0> at 0
    ACPI: EC: Look up EC in DSDT
    ACPI: Executed 1 blocks of module-level executable AML code
    ACPI: BIOS _OSI(Linux) query ignored
    ACPI: Interpreter enabled
    ACPI: (supports S0 S3 S4 S5)
    ACPI: Using IOAPIC for interrupt routing
    ACPI: Power Resource [PFA1] (off)
    ACPI: No dock devices found.
    PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
    ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
    pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
    pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
    pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
    pci_root PNP0A08:00: host bridge window [mem 0x000c0000-0x000c3fff]
    pci_root PNP0A08:00: host bridge window [mem 0x000c4000-0x000c7fff]
    pci_root PNP0A08:00: host bridge window [mem 0x000c8000-0x000cbfff]
    pci_root PNP0A08:00: address space collision: host bridge window [mem 0x000cc000-0x000cffff] conflicts with Video ROM [mem 0x000c0000-0x000cefff]
    pci_root PNP0A08:00: host bridge window [mem 0x000d0000-0x000d3fff]
    pci_root PNP0A08:00: host bridge window [mem 0x000d4000-0x000d7fff]
    pci_root PNP0A08:00: host bridge window [mem 0x000d8000-0x000dbfff]
    pci_root PNP0A08:00: host bridge window [mem 0x000dc000-0x000dffff]
    pci_root PNP0A08:00: host bridge window [mem 0x000e0000-0x000e3fff]
    pci_root PNP0A08:00: host bridge window [mem 0x000e4000-0x000e7fff]
    pci_root PNP0A08:00: host bridge window [mem 0x000e8000-0x000ebfff]
    pci_root PNP0A08:00: host bridge window [mem 0x000ec000-0x000effff]
    pci_root PNP0A08:00: host bridge window [mem 0x40000000-0xf7ffffff]
    pci_root PNP0A08:00: host bridge window [mem 0xfc000000-0xfed3ffff]
    pci_root PNP0A08:00: host bridge window [mem 0xfed45000-0xffffffff]
    pci 0000:00:04.0: PME# supported from D0 D3hot D3cold
    pci 0000:00:04.0: PME# disabled
    pci 0000:00:05.0: PME# supported from D0 D3hot D3cold
    pci 0000:00:05.0: PME# disabled
    pci 0000:00:11.0: reg 10: [io 0x8038-0x803f]
    pci 0000:00:11.0: reg 14: [io 0x804c-0x804f]
    pci 0000:00:11.0: reg 18: [io 0x8030-0x8037]
    pci 0000:00:11.0: reg 1c: [io 0x8048-0x804b]
    pci 0000:00:11.0: reg 20: [io 0x8010-0x801f]
    pci 0000:00:11.0: reg 24: [mem 0x52307000-0x523073ff]
    pci 0000:00:12.0: reg 10: [mem 0x52306000-0x52306fff]
    pci 0000:00:12.2: reg 10: [mem 0x52307600-0x523076ff]
    pci 0000:00:12.2: supports D1 D2
    pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot
    pci 0000:00:12.2: PME# disabled
    pci 0000:00:13.0: reg 10: [mem 0x52305000-0x52305fff]
    pci 0000:00:13.2: reg 10: [mem 0x52307500-0x523075ff]
    pci 0000:00:13.2: supports D1 D2
    pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot
    pci 0000:00:13.2: PME# disabled
    pci 0000:00:14.2: reg 10: [mem 0x52300000-0x52303fff 64bit]
    pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
    pci 0000:00:14.2: PME# disabled
    pci 0000:00:16.0: reg 10: [mem 0x52304000-0x52304fff]
    pci 0000:00:16.2: reg 10: [mem 0x52307400-0x523074ff]
    pci 0000:00:16.2: supports D1 D2
    pci 0000:00:16.2: PME# supported from D0 D1 D2 D3hot
    pci 0000:00:16.2: PME# disabled
    pci 0000:01:05.0: reg 10: [mem 0x40000000-0x4fffffff pref]
    pci 0000:01:05.0: reg 14: [io 0x7000-0x70ff]
    pci 0000:01:05.0: reg 18: [mem 0x52200000-0x5220ffff]
    pci 0000:01:05.0: reg 24: [mem 0x52100000-0x521fffff]
    pci 0000:01:05.0: supports D1 D2
    pci 0000:00:01.0: PCI bridge to [bus 01-01]
    pci 0000:00:01.0: bridge window [io 0x7000-0x7fff]
    pci 0000:00:01.0: bridge window [mem 0x52100000-0x522fffff]
    pci 0000:00:01.0: bridge window [mem 0x40000000-0x4fffffff 64bit pref]
    pci 0000:02:00.0: reg 10: [mem 0x51100000-0x5110ffff 64bit]
    pci 0000:02:00.0: supports D1
    pci 0000:02:00.0: PME# supported from D0 D1 D3hot
    pci 0000:02:00.0: PME# disabled
    pci 0000:00:04.0: PCI bridge to [bus 02-07]
    pci 0000:00:04.0: bridge window [io 0x3000-0x6fff]
    pci 0000:00:04.0: bridge window [mem 0x51100000-0x520fffff]
    pci 0000:00:04.0: bridge window [mem 0x50000000-0x50ffffff 64bit pref]
    pci 0000:08:00.0: reg 10: [mem 0x51000000-0x5103ffff 64bit]
    pci 0000:08:00.0: reg 18: [io 0x2000-0x207f]
    pci 0000:08:00.0: PME# supported from D0 D1 D2 D3hot D3cold
    pci 0000:08:00.0: PME# disabled
    pci 0000:00:05.0: PCI bridge to [bus 08-08]
    pci 0000:00:05.0: bridge window [io 0x2000-0x2fff]
    pci 0000:00:05.0: bridge window [mem 0x51000000-0x510fffff]
    pci 0000:00:05.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
    pci 0000:00:14.4: PCI bridge to [bus 09-09]
    pci 0000:00:14.4: bridge window [io 0xf000-0x0000] (disabled)
    pci 0000:00:14.4: bridge window [mem 0xfff00000-0x000fffff] (disabled)
    pci 0000:00:14.4: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
    pci_bus 0000:00: on NUMA node 0
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB4_._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB5_._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
    ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 11 12 14 15) *0
    ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 11 12 14 15) *0
    ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 11 12 14 15) *0
    ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 12 14 15) *0
    ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0
    ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 12 14 15) *0
    ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0
    ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0
    HEST: Table is not found!
    vgaarb: device added: PCI:0000:01:05.0,decodes=io+mem,owns=io+mem,locks=none
    vgaarb: loaded
    PCI: Using ACPI for IRQ routing
    PCI: pci_cache_line_size set to 64 bytes
    reserve RAM buffer: 0000000000002000 - 000000000000ffff
    reserve RAM buffer: 000000000009fc00 - 000000000009ffff
    reserve RAM buffer: 000000002e54a000 - 000000002fffffff
    reserve RAM buffer: 000000002fd3f000 - 000000002fffffff
    reserve RAM buffer: 000000002ff00000 - 000000002fffffff
    NetLabel: Initializing
    NetLabel: domain hash size = 128
    NetLabel: protocols = UNLABELED CIPSOv4
    NetLabel: unlabeled traffic allowed by default
    hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
    hpet0: 3 comparators, 32-bit 14.318180 MHz counter
    Switching to clocksource tsc
    pnp: PnP ACPI init
    ACPI: bus type pnp registered
    pnp: PnP ACPI: found 10 devices
    ACPI: ACPI bus type pnp unregistered
    system 00:01: [mem 0xfec00000-0xfec00fff] could not be reserved
    system 00:01: [mem 0xfee00000-0xfee00fff] has been reserved
    system 00:01: [mem 0xf8000000-0xfbffffff] could not be reserved
    system 00:08: [io 0x0400-0x04cf] has been reserved
    system 00:08: [io 0x04d0-0x04d1] has been reserved
    system 00:08: [io 0x04d6] has been reserved
    system 00:08: [io 0x0680-0x06ff] has been reserved
    system 00:08: [io 0x077a] has been reserved
    system 00:08: [io 0x0c00-0x0c01] has been reserved
    system 00:08: [io 0x0c14] has been reserved
    system 00:08: [io 0x0c50-0x0c52] has been reserved
    system 00:08: [io 0x0c6c] has been reserved
    system 00:08: [io 0x0c6f] has been reserved
    system 00:08: [io 0x0cd0-0x0cdb] has been reserved
    system 00:09: [mem 0x000e0000-0x000fffff] could not be reserved
    system 00:09: [mem 0xffe00000-0xffffffff] has been reserved
    system 00:09: [mem 0xfed80000-0xfed80fff] has been reserved
    pci 0000:00:01.0: PCI bridge to [bus 01-01]
    pci 0000:00:01.0: bridge window [io 0x7000-0x7fff]
    pci 0000:00:01.0: bridge window [mem 0x52100000-0x522fffff]
    pci 0000:00:01.0: bridge window [mem 0x40000000-0x4fffffff 64bit pref]
    pci 0000:00:04.0: PCI bridge to [bus 02-07]
    pci 0000:00:04.0: bridge window [io 0x3000-0x6fff]
    pci 0000:00:04.0: bridge window [mem 0x51100000-0x520fffff]
    pci 0000:00:04.0: bridge window [mem 0x50000000-0x50ffffff 64bit pref]
    pci 0000:00:05.0: PCI bridge to [bus 08-08]
    pci 0000:00:05.0: bridge window [io 0x2000-0x2fff]
    pci 0000:00:05.0: bridge window [mem 0x51000000-0x510fffff]
    pci 0000:00:05.0: bridge window [mem pref disabled]
    pci 0000:00:14.4: PCI bridge to [bus 09-09]
    pci 0000:00:14.4: bridge window [io disabled]
    pci 0000:00:14.4: bridge window [mem disabled]
    pci 0000:00:14.4: bridge window [mem pref disabled]
    pci 0000:00:01.0: setting latency timer to 64
    pci 0000:00:04.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    pci 0000:00:04.0: setting latency timer to 64
    pci 0000:00:05.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
    pci 0000:00:05.0: setting latency timer to 64
    pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
    pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
    pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
    pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000c3fff]
    pci_bus 0000:00: resource 8 [mem 0x000c4000-0x000c7fff]
    pci_bus 0000:00: resource 9 [mem 0x000c8000-0x000cbfff]
    pci_bus 0000:00: resource 10 [mem 0x000d0000-0x000d3fff]
    pci_bus 0000:00: resource 11 [mem 0x000d4000-0x000d7fff]
    pci_bus 0000:00: resource 12 [mem 0x000d8000-0x000dbfff]
    pci_bus 0000:00: resource 13 [mem 0x000dc000-0x000dffff]
    pci_bus 0000:00: resource 14 [mem 0x000e0000-0x000e3fff]
    pci_bus 0000:00: resource 15 [mem 0x000e4000-0x000e7fff]
    pci_bus 0000:00: resource 16 [mem 0x000e8000-0x000ebfff]
    pci_bus 0000:00: resource 17 [mem 0x000ec000-0x000effff]
    pci_bus 0000:00: resource 18 [mem 0x40000000-0xf7ffffff]
    pci_bus 0000:00: resource 19 [mem 0xfc000000-0xfed3ffff]
    pci_bus 0000:00: resource 20 [mem 0xfed45000-0xffffffff]
    pci_bus 0000:01: resource 0 [io 0x7000-0x7fff]
    pci_bus 0000:01: resource 1 [mem 0x52100000-0x522fffff]
    pci_bus 0000:01: resource 2 [mem 0x40000000-0x4fffffff 64bit pref]
    pci_bus 0000:02: resource 0 [io 0x3000-0x6fff]
    pci_bus 0000:02: resource 1 [mem 0x51100000-0x520fffff]
    pci_bus 0000:02: resource 2 [mem 0x50000000-0x50ffffff 64bit pref]
    pci_bus 0000:08: resource 0 [io 0x2000-0x2fff]
    pci_bus 0000:08: resource 1 [mem 0x51000000-0x510fffff]
    NET: Registered protocol family 2
    IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
    TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
    TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
    TCP: Hash tables configured (established 131072 bind 65536)
    TCP reno registered
    UDP hash table entries: 512 (order: 2, 16384 bytes)
    UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
    NET: Registered protocol family 1
    pci 0000:00:01.0: MSI quirk detected; subordinate MSI disabled
    pci 0000:01:05.0: Boot video device
    PCI: CLS 64 bytes, default 64
    Unpacking initramfs...
    Freeing initrd memory: 1556k freed
    Simple Boot Flag at 0x44 set to 0x1
    apm: BIOS not found.
    Scanning for low memory corruption every 60 seconds
    audit: initializing netlink socket (disabled)
    type=2000 audit(1290023602.626:1): initialized
    VFS: Disk quotas dquot_6.5.2
    Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    msgmni has been set to 1493
    alg: No test for stdrng (krng)
    Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
    io scheduler noop registered
    io scheduler deadline registered
    io scheduler cfq registered (default)
    pcieport 0000:00:04.0: setting latency timer to 64
    pcieport 0000:00:04.0: irq 40 for MSI/MSI-X
    pcieport 0000:00:05.0: setting latency timer to 64
    pcieport 0000:00:05.0: irq 41 for MSI/MSI-X
    ERST: Table is not found!
    isapnp: Scanning for PnP cards...
    isapnp: No Plug & Play device found
    Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
    serio: i8042 KBD port at 0x60,0x64 irq 1
    serio: i8042 AUX port at 0x60,0x64 irq 12
    mice: PS/2 mouse device common for all mice
    cpuidle: using governor ladder
    cpuidle: using governor menu
    TCP cubic registered
    NET: Registered protocol family 17
    Using IPI No-Shortcut mode
    PM: Resume from disk failed.
    registered taskstats version 1
    Initalizing network drop monitor service
    Freeing unused kernel memory: 416k freed
    udev[31]: starting version 163
    input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
    SCSI subsystem initialized
    libata version 3.00 loaded.
    ahci 0000:00:11.0: version 3.0
    ahci 0000:00:11.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
    ahci 0000:00:11.0: irq 42 for MSI/MSI-X
    ahci 0000:00:11.0: AHCI 0001.0200 32 slots 3 ports 6 Gbps 0x7 impl SATA mode
    ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part sxs
    scsi0 : ahci
    scsi1 : ahci
    scsi2 : ahci
    ata1: SATA max UDMA/133 abar m1024@0x52307000 port 0x52307100 irq 42
    ata2: SATA max UDMA/133 abar m1024@0x52307000 port 0x52307180 irq 42
    ata3: SATA max UDMA/133 abar m1024@0x52307000 port 0x52307200 irq 42
    ata3: SATA link down (SStatus 0 SControl 300)
    ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    ata1.00: ATA-8: Hitachi HTS545025B9A300, PB2OC64G, max UDMA/133
    ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
    ata1.00: configured for UDMA/133
    scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54502 PB2O PQ: 0 ANSI: 5
    ata2.00: ATAPI: TSSTcorp CDDVDW TS-L633C, TF20, max UDMA/100
    ata2.00: configured for UDMA/100
    scsi 1:0:0:0: CD-ROM TSSTcorp CDDVDW TS-L633C TF20 PQ: 0 ANSI: 5
    sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
    sd 0:0:0:0: [sda] Write Protect is off
    sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    sda:sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
    Uniform CD-ROM driver Revision: 3.20
    sr 1:0:0:0: Attached scsi CD-ROM sr0
    sda1 sda2 sda3 sda4
    sd 0:0:0:0: [sda] Attached SCSI disk
    EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
    rtc_cmos 00:04: RTC can wake from S4
    rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
    rtc0: alarms up to one day, 114 bytes nvram, hpet irqs
    udev[1064]: starting version 163
    atl1c 0000:08:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
    atl1c 0000:08:00.0: setting latency timer to 64
    atl1c 0000:08:00.0: version 1.0.0.2-NAPI
    thermal LNXTHERM:01: registered as thermal_zone0
    ACPI: Thermal Zone [THZN] (58 C)
    ACPI: acpi_idle registered with cpuidle
    ACPI: processor limited to max C-state 1
    input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
    ACPI: Power Button [PWRB]
    input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input2
    ACPI: Lid Switch [LID]
    input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
    ACPI: Power Button [PWRF]
    input: PC Speaker as /devices/platform/pcspkr/input/input4
    pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    sd 0:0:0:0: Attached scsi generic sg0 type 0
    sr 1:0:0:0: Attached scsi generic sg1 type 5
    shpchp 0000:00:01.0: HPC vendor_id 1022 device_id 9602 ss_vid 1022 ss_did 9602
    shpchp 0000:00:01.0: Cannot reserve MMIO region
    shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
    ACPI: AC Adapter [ADP0] (on-line)
    cfg80211: Calling CRDA to update world regulatory domain
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    ehci_hcd 0000:00:12.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
    ehci_hcd 0000:00:12.2: setting latency timer to 64
    ehci_hcd 0000:00:12.2: EHCI Host Controller
    ehci_hcd 0000:00:12.2: new USB bus registered, assigned bus number 1
    ehci_hcd 0000:00:12.2: debug port 1
    ehci_hcd 0000:00:12.2: irq 17, io mem 0x52307600
    ehci_hcd 0000:00:12.2: USB 2.0 started, EHCI 1.00
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 5 ports detected
    ehci_hcd 0000:00:13.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
    ehci_hcd 0000:00:13.2: setting latency timer to 64
    ehci_hcd 0000:00:13.2: EHCI Host Controller
    ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 2
    ehci_hcd 0000:00:13.2: debug port 1
    ehci_hcd 0000:00:13.2: irq 17, io mem 0x52307500
    ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 5 ports detected
    ehci_hcd 0000:00:16.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
    ehci_hcd 0000:00:16.2: setting latency timer to 64
    ehci_hcd 0000:00:16.2: EHCI Host Controller
    ehci_hcd 0000:00:16.2: new USB bus registered, assigned bus number 3
    ehci_hcd 0000:00:16.2: debug port 1
    ehci_hcd 0000:00:16.2: irq 17, io mem 0x52307400
    ehci_hcd 0000:00:16.2: USB 2.0 started, EHCI 1.00
    hub 3-0:1.0: USB hub found
    hub 3-0:1.0: 4 ports detected
    ACPI: Fan [FAN1] (off)
    ACPI: Battery Slot [BAT0] (battery present)
    piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
    acpi device:02: registered as cooling_device2
    input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:00/LNXVIDEO:00/input/input5
    ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
    usb 2-2: new high speed USB device using ehci_hcd and address 2
    Linux agpgart interface v0.103
    ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
    ohci_hcd 0000:00:12.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
    ohci_hcd 0000:00:12.0: setting latency timer to 64
    ohci_hcd 0000:00:12.0: OHCI Host Controller
    ohci_hcd 0000:00:12.0: new USB bus registered, assigned bus number 4
    ohci_hcd 0000:00:12.0: irq 18, io mem 0x52306000
    hub 4-0:1.0: USB hub found
    hub 4-0:1.0: 5 ports detected
    ohci_hcd 0000:00:13.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
    ohci_hcd 0000:00:13.0: setting latency timer to 64
    ohci_hcd 0000:00:13.0: OHCI Host Controller
    ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 5
    ohci_hcd 0000:00:13.0: irq 18, io mem 0x52305000
    hub 5-0:1.0: USB hub found
    hub 5-0:1.0: 5 ports detected
    ohci_hcd 0000:00:16.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
    ohci_hcd 0000:00:16.0: setting latency timer to 64
    ohci_hcd 0000:00:16.0: OHCI Host Controller
    ohci_hcd 0000:00:16.0: new USB bus registered, assigned bus number 6
    ohci_hcd 0000:00:16.0: irq 18, io mem 0x52304000
    ath9k 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    ath9k 0000:02:00.0: setting latency timer to 64
    hub 6-0:1.0: USB hub found
    hub 6-0:1.0: 4 ports detected
    ath: EEPROM regdomain: 0x65
    ath: EEPROM indicates we should expect a direct regpair map
    ath: Country alpha2 being used: 00
    ath: Regpair used: 0x65
    [drm] Initialized drm 1.1.0 20060810
    phy0: Selected rate control algorithm 'ath9k_rate_control'
    Registered led device: ath9k-phy0::radio
    Registered led device: ath9k-phy0::assoc
    Registered led device: ath9k-phy0::tx
    Registered led device: ath9k-phy0::rx
    phy0: Atheros AR9285 Rev:2 mem=0xf0c60000, irq=16
    Initializing USB Mass Storage driver...
    scsi3 : usb-storage 2-2:1.0
    usbcore: registered new interface driver usb-storage
    USB Mass Storage support registered.
    usb 3-4: new high speed USB device using ehci_hcd and address 2
    HDA Intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    HDA Intel 0000:00:14.2: setting latency timer to 64
    [drm] radeon defaulting to kernel modesetting.
    [drm] radeon kernel modesetting enabled.
    radeon 0000:01:05.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
    radeon 0000:01:05.0: setting latency timer to 64
    [drm] initializing kernel modesetting (RS880 0x1002:0x9712).
    [drm] register mmio base: 0x52200000
    [drm] register mmio size: 65536
    ATOM BIOS: Tos_Berlin10AD
    [drm] Clocks initialized !
    radeon 0000:01:05.0: VRAM: 256M 0xC0000000 - 0xCFFFFFFF (256M used)
    radeon 0000:01:05.0: GTT: 512M 0xA0000000 - 0xBFFFFFFF
    [drm] Detected VRAM RAM=256M, BAR=256M
    [drm] RAM width 32bits DDR
    [TTM] Zone kernel: Available graphics memory: 382460 kiB.
    [TTM] Initializing pool allocator.
    [drm] radeon: 256M of VRAM memory ready
    [drm] radeon: 512M of GTT memory ready.
    [drm] radeon: irq initialized.
    [drm] GART: num cpu pages 131072, num gpu pages 131072
    [drm] Loading RS780 Microcode
    Synaptics Touchpad, model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04731/0xa40000/0xa0000
    synaptics: Toshiba Satellite Pro C650D detected, limiting rate to 40pps.
    input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input6
    [drm] ring test succeeded in 0 usecs
    [drm] radeon: ib pool ready.
    [drm] ib test succeeded in 0 usecs
    [drm] Enabling audio support
    [drm] Unknown TV standard; defaulting to NTSC
    [drm] Radeon Display Connectors
    [drm] Connector 0:
    [drm] VGA
    [drm] DDC: 0x7e40 0x7e40 0x7e44 0x7e44 0x7e48 0x7e48 0x7e4c 0x7e4c
    [drm] Encoders:
    [drm] CRT1: INTERNAL_KLDSCP_DAC1
    [drm] Connector 1:
    [drm] LVDS
    [drm] DDC: 0x7e50 0x7e50 0x7e54 0x7e54 0x7e58 0x7e58 0x7e5c 0x7e5c
    [drm] Encoders:
    [drm] LCD1: INTERNAL_KLDSCP_LVTMA
    [drm] radeon: power management initialized
    [drm] fb mappable at 0x40141000
    [drm] vram apper at 0x40000000
    [drm] size 4325376
    [drm] fb depth is 24
    [drm] pitch is 5632
    scsi 3:0:0:0: Direct-Access Generic- Multi-Card 1.00 PQ: 0 ANSI: 0 CCS
    sd 3:0:0:0: Attached scsi generic sg2 type 0
    sd 3:0:0:0: [sdb] Attached SCSI removable disk
    Linux video capture interface: v2.00
    uvcvideo: Found UVC 1.00 device USB Camera (10f1:1a2a)
    input: USB Camera as /devices/pci0000:00/0000:00:16.2/usb3/3-4/3-4:1.0/input/input7
    usbcore: registered new interface driver uvcvideo
    USB Video Class driver (v0.1.0)
    Console: switching to colour frame buffer device 170x48
    fb0: radeondrmfb frame buffer device
    drm: registered panic notifier
    Slow work thread pool: Starting up
    Slow work thread pool: Ready
    [drm] Initialized radeon 2.5.0 20080528 for 0000:01:05.0 on minor 0
    EXT4-fs (sda3): re-mounted. Opts: (null)
    EXT4-fs (sda3): re-mounted. Opts: (null)
    EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null)
    Adding 265068k swap on /dev/sda2. Priority:-1 extents:1 across:265068k
    atl1c 0000:08:00.0: irq 43 for MSI/MSI-X
    atl1c 0000:08:00.0: irq 43 for MSI/MSI-X
    wlan0: deauthenticating from 00:1d:7e:af:65:43 by local choice (reason=3)
    wlan0: deauthenticating from 00:1d:7e:af:65:43 by local choice (reason=3)
    wlan0: authenticate with 00:1d:7e:af:65:43 (try 1)
    wlan0: authenticated
    wlan0: associate with 00:1d:7e:af:65:43 (try 1)
    wlan0: RX AssocResp from 00:1d:7e:af:65:43 (capab=0x421 status=0 aid=2)
    wlan0: associated
    cfg80211: Calling CRDA for country: NA
    fuse init (API version 7.14)
    ata1.00: configured for UDMA/133
    ata1: EH complete
    EXT4-fs (sda3): re-mounted. Opts: commit=0
    EXT4-fs (sda4): re-mounted. Opts: commit=0
    NET: Registered protocol family 10
    lo: Disabled Privacy Extensions
    ADDRCONF(NETDEV_UP): eth0: link is not ready
    wlan0: no IPv6 routers present
    process `skype' is using obsolete setsockopt SO_BSDCOMPAT
    usb 1-2: new high speed USB device using ehci_hcd and address 2
    scsi4 : usb-storage 1-2:1.1
    scsi 4:0:0:0: Direct-Access ZTE Mass Storage ffff PQ: 0 ANSI: 2
    sd 4:0:0:0: Attached scsi generic sg3 type 0
    sd 4:0:0:0: [sdc] Attached SCSI removable disk
    usb 1-2: USB disconnect, address 2
    amixer
    Simple mixer control 'Master',0
    Capabilities: pvolume pswitch pswitch-joined penum
    Playback channels: Front Left - Front Right
    Limits: Playback 0 - 74
    Mono:
    Front Left: Playback 74 [100%] [0.00dB] [on]
    Front Right: Playback 74 [100%] [0.00dB] [on]
    Simple mixer control 'PCM',0
    Capabilities: pvolume penum
    Playback channels: Front Left - Front Right
    Limits: Playback 0 - 255
    Mono:
    Front Left: Playback 213 [84%] [-8.40dB]
    Front Right: Playback 213 [84%] [-8.40dB]
    Simple mixer control 'Mic B',0
    Capabilities: cswitch cswitch-joined cswitch-exclusive penum
    Capture exclusive group: 0
    Capture channels: Mono
    Mono: Capture [off]
    Simple mixer control 'Mic C',0
    Capabilities: cswitch cswitch-joined cswitch-exclusive penum
    Capture exclusive group: 0
    Capture channels: Mono
    Mono: Capture [off]
    Simple mixer control 'Mic E',0
    Capabilities: cswitch cswitch-joined cswitch-exclusive penum
    Capture exclusive group: 0
    Capture channels: Mono
    Mono: Capture [on]
    Simple mixer control 'Mic F',0
    Capabilities: cswitch cswitch-joined cswitch-exclusive penum
    Capture exclusive group: 0
    Capture channels: Mono
    Mono: Capture [off]
    Simple mixer control 'IEC958',0
    Capabilities: pswitch pswitch-joined penum
    Playback channels: Mono
    Mono: Playback [on]
    Simple mixer control 'IEC958 Default PCM',0
    Capabilities: pswitch pswitch-joined penum
    Playback channels: Mono
    Mono: Playback [on]
    Simple mixer control 'Capture',0
    Capabilities: cvolume cswitch penum
    Capture channels: Front Left - Front Right
    Limits: Capture 0 - 80
    Front Left: Capture 80 [100%] [6.00dB] [on]
    Front Right: Capture 80 [100%] [6.00dB] [on]
    Simple mixer control 'Analog Mic Boost',0
    Capabilities: cenum
    Items: '0dB' '10dB' '20dB' '30dB' '40dB'
    Item0: '0dB'
    Simple mixer control 'Digital',0
    Capabilities: cvolume penum
    Capture channels: Front Left - Front Right
    Limits: Capture 0 - 120
    Front Left: Capture 98 [82%] [19.00dB]
    Front Right: Capture 98 [82%] [19.00dB]
    Any help would be thoroughly appreciated.
    Thanks!
    John.

    firstly, sorry for my english
    I have HP ProBook 4515s. the lspci says the same on 00:14.*
    00:00.0 Host bridge: Advanced Micro Devices [AMD] RS880 Host Bridge
    00:01.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (int gfx)
    00:04.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 0)
    00:07.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 3)
    00:09.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 4)
    00:11.0 SATA controller: ATI Technologies Inc SB700/SB800 SATA Controller [AHCI mode]
    00:12.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller
    00:12.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller
    00:12.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller
    00:13.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller
    00:13.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller
    00:13.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller
    00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 3c)
    00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA)
    00:14.3 ISA bridge: ATI Technologies Inc SB700/SB800 LPC host controller
    00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge
    00:14.5 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller
    00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration
    00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Address Map
    00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller
    00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control
    00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Link Control
    01:05.0 VGA compatible controller: ATI Technologies Inc M880G [Mobility Radeon HD 4200]
    01:05.1 Audio device: ATI Technologies Inc RS880 Audio Device [Radeon HD 4200]
    02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8072 PCI-E Gigabit Ethernet Controller (rev 10)
    06:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01)
    looks like we've got the same chipset.
    one stupid pdf-file found on hp.com sais that the codec is ADI 1984AJCPZ High Definition CODEC, but I can't be sure...
    i tried different model= parameters to snd-hda-intel module, but nothin helps
    i can capture external jack-in microphone only if external jack-out is free (which is completely stupid for home audio studio experiencing)
    internal phones are not mute automatically until jack-in freed (but i can easily mute them in alsamixer instead)
    if anyone find a workaround or anything useful, please report here or use my contacts

  • My audio works but not the video

    My audio will work but when I want to watch any video on any different app the video doesn't work.why?

    Try:
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Reset all settings      
    Go to Settings > General > Reset and tap Reset All Settings.
    All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
    - Restore from backup. See:                                                
    iOS: How to back up                                                                
    - Restore to factory settings/new iOS device.             
    If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
    Apple Retail Store - Genius Bar                                      

  • Audio working but not the video?

    I have iChat AV 3.1.8 (v445)
    And OSX (10.4.11)
    I am trying to connect to a user using AIM, and the video connection is establishing but it wont show the video, only the audio.
    Things I think you would need to know.
    Using Wi-Fi connection.
    The other user does not have a camera attached.
    Have my restriction set to 200.
    Using Comcast.
    Now when the user connects their camera I get a error message saying "There was a communication error during your chat" with a send to Apple option.

    I've been having this problem since upgrading to leopard. On my iMac with Tiger i could video chat with AIM users in a one way chat without any problems. Upgraded to leopard and all they have is a black screen, but the audio is coming through. The only thing that was changed was the OS Version.
    I am also having the same exact problem on my new MacBook, which came with leopard installed.
    On a side note, i can nolonger video chat with Tiger users, but everything seems to be fine with other Leopard users.
    Seems like there are a lot of these problems going around. Any idea on an ETA for a fix?

  • Video and Audio work but not screen share

    I am able to connect and video chat with a mb running 10.5.4.
    When I request screen share, they authorize, seems to start to connect then I get the message "screen sharing could not be established."
    Is this a port issue?
    Thanks in advance!

    Oh My !! You are doing things the difficult way.
    Hopefully you have got both ends set in System Preferences > Quicktime > Streaming to 1.5Mbps
    (if you have to change iChat will need restarting).
    In the iChat Menu >Preferences > Video Section > Bandwidth drop down both ends need to be on 500kbps to get around what Comcast and Road Runner do to manage their Data Stream. This can be set in a chat. The two ISP s do things to try and stop people using File Sharing apps like BitTorrent but it impinges on iChat.
    The reason why I say it is a port issue.
    I run an App called Little Snitch.
    It tells me the ports and the IPs applications are connecting to.
    In a successful Video chats I see port 16402 on people's Public IP and if they have a Router a LAN IP as well.
    When in a Screen Share situation I also get another port.
    Screen Sharing in iChat iss related to the way it is/was done in Apple Remote Desktop (ARD).
    in fact in the iChatAgent .plist you can see the Setting
    (It is in fact Off in this Pic)
    Apple Remote Desktop uses port 5900 and 5988.
    However, Little Snitch reports to me a fairly random port when I use it and shows a number in the 50000 range.
    I use UPnP in my combined Modem/router which seems to cope with this random port.
    UPnP (Universal Plug and Play) allows any port the App wants to open to be open - control is with the App.
    This Doc by Apple tells you the ports to open if Port Forwarding for iChat 3
    It includes the Bonjour ones, the Jabber ones the AIM ones and the A/V ones.
    http://support.apple.com/kb/HT1507?viewlocale=en_US
    This second Doc by Apple is about the port changes to iChat 4
    http://support.apple.com/kb/HT2282?viewlocale=en_US
    This one only tells you about the A/V ports and not the other you need.
    AS it is short on info that is known about it stands to reason the info on Screen Sharing ports is also missing.
    This link is about the Linksys WRT54GS
    http://portforward.com/english/routers/port_forwarding/Linksys/WRT54GS/iChat.htm
    Near the top of the page is the Info to use in a web browser to access the set up pages.
    Follow the Instructions to to access the device and set the Unblocking of Anonymous Pings in the Security page.
    Stop following the Instructions and go to the Administration page.
    In here you will find UPnP.
    This should be Enabled (Save Settings if you need to)
    You will see in the rest of the Instructions that Port Forwarding is in Applications and Gaming as a sub tab. If anything is set here it will need to be Disabled.
    As will anything in Port Triggering and DMZ tabs.
    The Linksys WCG200
    I can not see the one with cc at the end on the Port Forward.com list so I have picked version 2
    http://portforward.com/english/routers/port_forwarding/Linksys/WCG200v2/iChat.ht m
    You can see the pics are similar.
    Although it does not say, also disable the Block to Responses to Internet Pings on the Security page (as well as having the Firewall Off).
    Then do the same as above. Enable UPnP and Save Settings - Disable anything in Applications and Gaming and again save settings.
    As I said before UPnP will allow the apps to open the ports they need and will therefore cope with the fact we don't know the precise port iChat is supposed to use.
    Out of the Box list.
    Apple have a list that was started at iChat 2
    http://support.apple.com/kb/HT1787?viewlocale=en_US
    Although the Doc was updated in June this was only for the new numbering system.
    You will notice under the table that some still need tweaks.
    Realistically most devices will need some tweaks and turning on UPnP can be the smallest.
    Most Netgears have UPnP on by default.
    However they have the Internet Ping Blocking and they have a DOS or SPI firewall that can impinge on iChat 4 as all the data is on one port and Faster internet speeds mean more data can be sent bumping into the threshold that these work (And get in the way).
    MIMO devices that tend to come with two or more antenna are a problem for iChat as the Wireless signal is effectively duplicated and iChat see this as two network connections and can not use them - if you are thinking of being wireless.
    9:04 PM Wednesday; August 20, 2008

  • Why is youtube audio working but not video?

    Youtube worked well 2 days ago but since then only the audio has been working with a blacked out background....I haven't  changed anything just updated software in App Store... any suggestions?

    First to do is to uninstall all previous versions of flash player by using Flash Player Uninstaller.
    After you update directly from Adobe Flash Player Software website, repair permissions and restart your computer.

  • I am travelling abroad and want to buy a local sim card for my iphone 4. will the new sim work if not will apple open it for me

    HI i am going on holiday soon and i will be there for 2 weeks and wanted to use a local sim to call home and data because my current network provider (orange) will charge me the earth for internet data. will apple open the phone for me touse a local sim in the carribean

    As stated, Apple does not unlock phones. If you are using Orange in the UK, they do offer unlocking. See this page for information: http://help.orange.co.uk/orangeuk/support/personal/474187

  • When sending video from my iphone to apple tv it says on screen it is doing it but it wont play on tv but audio works great

    when sending video from my iphone to apple tv it says on screen it is doing it but it wont play on tv but audio works great

    Welcome to the Apple Community.
    Websites and third party Apps need enabling before they will allow AirPlay of Video content. Some Website/App developers have not enabled their products, some simply haven't got around to it yet, others have stated that they won't be enabling AirPlay (likely as a result of licensing issues).
    I have created a User Tip to list Apps that have been tested with Video Airplay, if you have any Apps that you have tested please email me details and I'll add them to the User Tip.

  • HT4108 What is required to use the video composite out on the iPhone 4.  Left and right audio works ok

    What is required to use the video composite out on the iPhone 4   The left and right audio works ok

    Please not that the iPhone uses mono channel for internal speakers, the other path that you see is not the speaker per say. It is the phone microphone. Try using headphones, you will hear both channels. If the problem still persists when using headphones, check your sound balancing in the settings. Go to setting-general-accessibility scroll down and check the slide under mono audio. It should be put at the centre for you to hear both channels ON YOUR HEADPHONES

  • Audio on Menus not playing

    Hi all,
    I wonder if anyone can help me.
    Using Encore on CS4, I created a project with three motion menus. The text was adapted from an Adobe template and the 'motion'' elements (video and audio) were created in Premiere, saved as an MPEG, imported into Encore as an asset and then alt-dragged to the menus. All of this works well. I then preview and build the motion menus with the preview buttion and everything plays well, the video and the audio (though it would be nice to have some voume control - but that's another story) are great and the menu structure (1st play menu and two subs) play fine. I then build the DVD. Firstly burned directly to DVD, the on subsequent tries as an image and as a folder. On all of them there is no audio on the menus. The timelines that the menus que are fine, the audio works but not on the menus.
    In frustration I created a flash file of the same project, and the audio was great. All there. I then went and analysed the DVD folder I created earlier and DVD Shrink found the menus and even found found associated audio as LPCM2-ch but alas, even using this program to compile an .ISO nothing improved.
    Any ideas?
    Thanks

    ......... I also do not want them rushing for the remote, to mute loud Menu Audio, only to have to then turn up the Volume, when the DVD plays. I like to "ease" the user into things. I find too many commercial DVD's, where the Menu Audio Volume is about +6dB above the other Audio and hate that. It does get my attention, but in a very bad way. It also scares my Bulldogs!  
    Good luck,
    Hunt
    Oh, dear me yes.
    The way I have found for menu audio - if you really must have it - is to halve the level from what you think is comfortable, and then set it to loop 20 or 30 times over - you would be surprised at hiw quickly this becomes very annoying.......and now place yourself in your customers shoes.
    @ the OP.
    As Jeff says, please retry with Dolby DIgital or LPCM, LPCM definitely if you are looping on a tight loop.
    MPEG audio is not your friend.

  • Airplay audio does not sometimes transfer to apple tv?

    Airplay audio does not sometimes transfer to apple tv?
    Sometimes I have to restart my apple tv to get audio, I only get video.
    Do you guys have the same issue?
    It's anoying to restart my apple tv everytime I want to watch a movie over airplay.
    /Anders

    Ok, but this doeasn't work for all my streaming services, I'm streaming songs with spotify and sports with different streaming services. My other options is to use a looong hdmi cable, would be nice to do it wireless. And airplay works most of the time, even for hd streaming video.

  • Audio is sometimes not working

    Hi,
    Sometimes the Audio interface is not found and the following message is in the syslog file available:
    Jan 31 11:41:43 localhost kernel[0]: Sound assertion "1" failed in "AppleOnboardAudio/PlatformInterfaceI2C_PlatformFunction.cpp" at line 328 goto handler
    Jan 31 11:41:43 localhost kernel[0]: ^PSound assertion "!result" failed in "AppleOnboardAudio/PlatformInterface.cpp" at line 138 goto Exit
    Jan 31 11:41:43 localhost kernel[0]: ^PSound assertion "!mPlatformInterface->init ( provider, this, AppleDBDMAAudio::kDBDMADeviceIndex, mPlatformInterfaceSupport, irqEnableMask )" failed in "AppleOnboardAudio/AppleOnboardAudio.cpp" at line 3076 goto Exit
    Jan 31 11:41:43 localhost kernel[0]: ^PSound assertion "!result" failed in "AppleOnboardAudio/AppleOnboardAudio.cpp" at line 173 goto Exit
    Jan 31 11:41:43 localhost kernel[0]: ^P
    Has somebody simliar expirience ?

    Hi,
    Sometimes the Audio interface is not found and the following message is in the syslog file available:
    Jan 31 11:41:43 localhost kernel[0]: Sound assertion "1" failed in "AppleOnboardAudio/PlatformInterfaceI2C_PlatformFunction.cpp" at line 328 goto handler
    Jan 31 11:41:43 localhost kernel[0]: ^PSound assertion "!result" failed in "AppleOnboardAudio/PlatformInterface.cpp" at line 138 goto Exit
    Jan 31 11:41:43 localhost kernel[0]: ^PSound assertion "!mPlatformInterface->init ( provider, this, AppleDBDMAAudio::kDBDMADeviceIndex, mPlatformInterfaceSupport, irqEnableMask )" failed in "AppleOnboardAudio/AppleOnboardAudio.cpp" at line 3076 goto Exit
    Jan 31 11:41:43 localhost kernel[0]: ^PSound assertion "!result" failed in "AppleOnboardAudio/AppleOnboardAudio.cpp" at line 173 goto Exit
    Jan 31 11:41:43 localhost kernel[0]: ^P
    Has somebody simliar expirience ?

  • Macbook Air Late 2010 model, 10.6.7, 2.13 4g ram. Trackpad is not working properly and in sometimes not at all.

    Macbook Air Late 2010 model, 10.6.7, 2.13 4g ram. Trackpad is not working properly and in sometimes not at all. Need suggestions to resolve this issue?  I have applied all Mac updates and still having problems with the trackpad.

    The machine has a 1 year warranty, book an appointment with your local Apple Store or AASP to have it looked at.
    You can try doing a SMC reset however I don't think that is the solution.
    SMC RESET
    • Shut down the computer.
    • Plug in the MagSafe power adapter to a power source, connecting it to the Mac if its not already connected.
    • On the built-in keyboard, press the (left side) Shift-Control-• Option keys and the power button at the same time.
    • Release all the keys and the power button at the same time.
    • Press the power button to turn on the computer.
    PRAM RESET
    • Shut down the computer.
    • Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.
    • Turn on the computer.
    • Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
    • Hold the keys down until the computer restarts and you hear the startup sound for the second time.
    • Release the keys.

  • My iTunes v.10.6.3.25 is intermittently refusing to open. Sometimes re-booting my laptop works, sometimes not. I just put the computer to sleep, and when I woke it up, iTunes started automatically. Any thoughts?

    My iTunes v.10.6.3.25 is intermittently refusing to open. Sometimes re-booting my laptop works, sometimes not. I just put the computer to sleep, and when I woke it up, iTunes started automatically (I had been trying to open it just before by clicking on a song file in my Documents window, and that's the song that started playing when the pc woke up). I went to my iTunes Help and clicked Updates/download iTunes 10.7 twice, but got nothing. Now, Im wondering if I should downloacd the entire 10.7, or whether that would overwrite all my files, erasing my songs. Anybody know? Thanks.

    Hey thanks for replying.
    Here's what I did:
    First I tried the Winsock reset in the Command prompt. Nothing changed.
    Next, I tried the instructions on http://http://support.apple.com/kb/TS4123. The only other program that came up on the 'Winsock Providers' tab on the program was 2 Windows Live applications, which I can do without. So I deleted all Windows Live Applications.
    I did the Winsock reset in the Command Prompt again and rebooted my comp.
    Unfortunately, nothing has changed. iTunes keeps freezing at various stages of the sync, then shows the candy cane-striped bar with either the words 'Finishing sync' or 'Cancelling sync', before showing the Apple logo.
    Sometimes, iTunes gets to the syncing stage - "Copying # of ####" - where it will trudge through the first, second and third tracks before flashing "Copying 4 of ####" for a split second and I catch "Cancelling sync" briefly before the Apple logo appears.
    Again, I've repeated the steps I mentioned in my previous post. Does ANYONE know when the new version of iTunes is set to be released?! This one is driving me INSANE, to say the least!!

Maybe you are looking for