Sony A7 failed to turn on after updating firmware 2.00
As i mentioned, my Sony A7 failed to turn on after updating firmware 2.00. It just appear a blank screen after click the finished button on the updating app on Mac. I waited for more than an hour and there is still no thing happened.
I bought the Sony A7II a few days ago. It initially charged just fine, but today I tried to charge it using the cable with an electrical outlet as well as the USB to computer. Neither one would get the charge light to illuminate. Not feeling the love Sony. I just purchased a Flash, wrist belt, filters, etc... I'm definitely not happy. It seems this is a problem!
Similar Messages
-
Mac 10.6 won't turn off after update
Macbook air a1304 won't turn off after updating unless you push on/off button.
Phone your nearest HP Support to request warranty service. Worldwide contact info can be accessed here>Contact HP
******Clicking the Thumbs-Up button is a way to say -Thanks!.******
**Click Accept as Solution on a Reply that solves your issue to help others** -
My iphone4 wont turn on after updating to ios5
my iphone4 wont turn on after updating to ios5
Hi
Sounds like it's broken in a potentially major way after the drop. You really should take it to your nearest Apple Store/Apple Authorised Repair Centre a diagnosis and quote.
Can't think of anything else any of us on this user-to-user forum can do for you?
HTH?
Tony -
Ipad air wont turn on after update today?
ipad wont turn on after update today. cannot do a hard reset either...
tried holding the power and home at the same time, still won't turn on suggestions?How long did you hold the power and home buttons? You need to do that for about 30 seconds, sometimes even more before the apple logo appears.
-
Iphone does not turn on after update to ios 7
My iphone dies not turn on after update to ios 7
it keeps showing the message : (connect to itunes)What type of computer do you have?
Were you updated to the latest version of iTunes?
You may need to follow these steps:
http://support.apple.com/kb/TS3281?viewlocale=en_US
Good luck! -
My Iphone doesnt turn on after updating. It keeps on blinking the apple logo, after seeing the low battery image, i tried to charge the iphone. After charging for 30 minutes, it still wont turn on but keeps on blinking the apple logo. It has been blinking for 2 days. Then I tried to connect to itunes, but itunes cant recognize the device. What should I do?
See Here > http://support.apple.com/kb/HT1808
You may need to try this More than Once... Be sure to Follow ALL the Steps..
But... if the Device has been Modified... this will Not necessarily work.
Unauthorized modification of iOS > http://support.apple.com/kb/HT3743 -
Kernel panics after updating firmware
Kernel panics began at startup after updating firmware about 2 weeks ago. Went through the KP repair routines prescribed by thexlab.com. Found no problems with the hard drive, permissions, etc. Did erase and install (with Leopard OS dvd bought from best buy) after archiving files to external HD and was able to startup normally. Updated OS to 10.5.7, along with several other items (iTunes was one of them). Put previously copied files (mostly iTunes). The computer ran successfully for a few days and then started getting KP's at startup again. Did another erase and install. Had success. Loaded iLife and Office 08 to have something to try to test the machine with. Shut down the computer and restarted successfully. I had forgotten I had not tested the RAM so downloaded Memtest. Tried to run it but the computer froze half way through the test. Did a hard shutdown, then tried to restart normally and got the KP again at startup. Here is the panic log:
Sun Jul 5 18:24:05 2009
panic(cpu 1 caller 0x001A7BED): Kernel trap at 0x00b10612, type 14=page fault, registers:
CR0: 0x8001003b, CR2: 0x000000b8, CR3: 0x0134c000, CR4: 0x00000660
EAX: 0x43ec9630, EBX: 0x049cf804, ECX: 0x04e15800, EDX: 0x00000000
CR2: 0x000000b8, EBP: 0x43ec9668, ESI: 0x00000000, EDI: 0xffffffff
EFL: 0x00010246, EIP: 0x00b10612, CS: 0x00000008, DS: 0x04e10010
Error code: 0x00000000
Backtrace, Format - Frame : Return Address (4 potential args on stack)
0x43ec9408 : 0x12b0e1 (0x4555b4 0x43ec943c 0x133238 0x0)
0x43ec9458 : 0x1a7bed (0x45e568 0xb10612 0xe 0x45dd24)
0x43ec9538 : 0x19e517 (0x43ec9550 0x1 0x43ec9668 0xb10612)
0x43ec9548 : 0xb10612 (0xe 0x48 0x10 0xb40010)
0x43ec9668 : 0xb1753d (0xc1d00005 0x1000000 0x1000003 0x40)
0x43ec96c8 : 0xb0bfc0 (0x43ec9858 0x43ec9808 0x0 0xafe41c)
0x43ec9828 : 0xb00132 (0x0 0x600d600d 0x7027 0x43ec9858)
0x43ec98e8 : 0xca58de (0xc1d00005 0x1000000 0x1000003 0x40)
0x43ec9918 : 0xcae273 (0x2436f000 0x1000000 0x88100090 0x3e)
0x43ecb8a8 : 0xc92d8a (0x2436f000 0x1000000 0x15 0x2436f01c)
0x43ecb9a8 : 0xafa472 (0x2436f000 0x0 0x43ecbab2 0x80)
0x43ecba08 : 0xaf15a5 (0x48af000 0x0 0x43ecbab2 0x80)
0x43ecbb38 : 0xaf2d74 (0x48af000 0xaf6358 0x43ecbbec 0x4)
0x43ecbc08 : 0xade139 (0x48af000 0x1 0x0 0x13)
0x43ecbc68 : 0xad7940 (0x48af000 0x2407 0x43ecbd2c 0x48af000)
0x43ecbc98 : 0x40c515 (0x48af000 0x4a40130 0x4a40130 0x0)
Backtrace continues...
Kernel loadable modules in backtrace (with dependencies):
com.apple.NVDAResman(5.1.6)@0xaf9000->0xd25fff
dependency: com.apple.iokit.IONDRVSupport(1.5)@0xaeb000
dependency: com.apple.iokit.IOPCIFamily(2.4)@0x63b000
dependency: com.apple.iokit.IOGraphicsFamily(1.5)@0xacf000
com.apple.iokit.IONDRVSupport(1.5)@0xaeb000->0xaf8fff
dependency: com.apple.iokit.IOPCIFamily(2.4)@0x63b000
dependency: com.apple.iokit.IOGraphicsFamily(1.5)@0xacf000
com.apple.iokit.IOGraphicsFamily(1.5)@0xacf000->0xaeafff
dependency: com.apple.iokit.IOPCIFamily(2.4)@0x63b000
BSD process name corresponding to current thread: WindowServer
Mac OS version:
9A581
Kernel version:
Darwin Kernel Version 9.0.0: Tue Oct 9 21:35:55 PDT 2007; root:xnu-1228~1/RELEASE_I386
System model name: MacBookPro3,1 (Mac-F42388C8)
Was able to start up in safe mode and ran memtest again, this time having success and finding no RAM problems from the single run of Memtest. Shut down and restarted successfully.
Turned the computer off for the night and just restarted it successfully about 24 hours later, and it is still running.
I presently have about 130GB of free space on my HD. I don't have any peripherals attached. The computer gets fairly warm at times but certainly not excessively.
Can anyone decipher my KP log and see if there is a fixable problem?
thanks in advance,
Pat LeopardHad another kernel panic at startup this morning. I had the Leopard DVD in and was contemplating another erase and install, but tried to back out of it. On restart the KP happened. Here is the log:
Wed Jul 8 10:44:41 2009
panic(cpu 0 caller 0x001A7BED): Kernel trap at 0x00b10612, type 14=page fault, registers:
CR0: 0x8001003b, CR2: 0x000000b8, CR3: 0x0134c000, CR4: 0x00000660
EAX: 0x2ebb1630, EBX: 0x04e20404, ECX: 0x04de7000, EDX: 0x00000000
CR2: 0x000000b8, EBP: 0x2ebb1668, ESI: 0x00000000, EDI: 0xffffffff
EFL: 0x00010246, EIP: 0x00b10612, CS: 0x00000008, DS: 0x04de0010
Error code: 0x00000000
Backtrace, Format - Frame : Return Address (4 potential args on stack)
0x2ebb1408 : 0x12b0e1 (0x4555b4 0x2ebb143c 0x133238 0x0)
0x2ebb1458 : 0x1a7bed (0x45e568 0xb10612 0xe 0x45dd24)
0x2ebb1538 : 0x19e517 (0x2ebb1550 0x1 0x2ebb1668 0xb10612)
0x2ebb1548 : 0xb10612 (0xe 0x48 0x10 0xb40010)
0x2ebb1668 : 0xb1753d (0xc1d00001 0x1000000 0x1000003 0x40)
0x2ebb16c8 : 0xb0bfc0 (0x2ebb1858 0x2ebb1808 0x0 0xafe41c)
0x2ebb1828 : 0xb00132 (0x0 0x600d600d 0x7027 0x2ebb1858)
0x2ebb18e8 : 0xca58de (0xc1d00001 0x1000000 0x1000003 0x40)
0x2ebb1918 : 0xcae273 (0x2435f000 0x1000000 0x88100090 0x3e)
0x2ebb38a8 : 0xc92d8a (0x2435f000 0x1000000 0x15 0x2435f01c)
0x2ebb39a8 : 0xafa472 (0x2435f000 0x0 0x2ebb3ab2 0x80)
0x2ebb3a08 : 0xaf15a5 (0x4837800 0x0 0x2ebb3ab2 0x80)
0x2ebb3b38 : 0xaf2d74 (0x4837800 0xaf6358 0x2ebb3bec 0x4)
0x2ebb3c08 : 0xade139 (0x4837800 0x1 0x0 0x13)
0x2ebb3c68 : 0xad7940 (0x4837800 0x2407 0x2ebb3d2c 0x4837800)
0x2ebb3c98 : 0x40c515 (0x4837800 0x4a0bc40 0x4a0bc40 0x0)
Backtrace continues...
Kernel loadable modules in backtrace (with dependencies):
com.apple.NVDAResman(5.1.6)@0xaf9000->0xd25fff
dependency: com.apple.iokit.IONDRVSupport(1.5)@0xaeb000
dependency: com.apple.iokit.IOPCIFamily(2.4)@0x63b000
dependency: com.apple.iokit.IOGraphicsFamily(1.5)@0xacf000
com.apple.iokit.IONDRVSupport(1.5)@0xaeb000->0xaf8fff
dependency: com.apple.iokit.IOPCIFamily(2.4)@0x63b000
dependency: com.apple.iokit.IOGraphicsFamily(1.5)@0xacf000
com.apple.iokit.IOGraphicsFamily(1.5)@0xacf000->0xaeafff
dependency: com.apple.iokit.IOPCIFamily(2.4)@0x63b000
BSD process name corresponding to current thread: WindowServer
Mac OS version:
9A581
Kernel version:
Darwin Kernel Version 9.0.0: Tue Oct 9 21:35:55 PDT 2007; root:xnu-1228~1/RELEASE_I386
System model name: MacBookPro3,1 (Mac-F42388C8)
I left the computer alone for a while and when I hit the power button it came right up.
I'm going to pull RAM modules per your suggestion.
thanks,
Pat Leopard -
Compass application can't running well after update firmware to 20120726
my windpad7 can't run compass application well after update firmware to Android_2.3.1_MSI_02_20120726 but it can pointing well if i turn it upside down (face down). i use the same application that running well on earlier firmware and I've try using another typical application and the result is the same,.. anyone experienced it?
on my n73 i can go to app manager and reinstall them.
if u wanna remove it, then reinstall them and uninstall.
Blackberry Bold -
Some buttons without tones after updating firmware...
Hi.
After updated firmware to version 20.0.080 (5530 Xpress Music), some tones and vibrates at dialing pad (just numbers) and at Contacts (main screen) don't work any more.
All other functions work normaly just as described, but some tones and vibrating functions doest'n seem to react. I have set touch screen tones on level 2, also the vibrate on level 2. Tryed to reinstal the latest firmware again, done succesfuly, but no changes.
Should I try to restore the phone by *#7370# ???
Is anybody facing the same issue ???
br,Hey,
I have the same problem with my phone. After the update, installing v.20.0.080 the dial tone from the keypad just dissapeared. These morons at Nokia instead of adding letters to the keypad dialer with the new firmware, they went further and removed the dial tone. Such a progressive step.. -
Apple TV doesn´t work at all after updating firmware!
After updating firmware Apple TV 3 the only thing that works is the little lamp on the front...it´s steadily blinks. It doesn´t response to remote control, and don´t show up threaded via USB in Itunes for resetting.
Model: Apple TV 3
Itunes: 12.0.1.26
What to do?The update didn't apply correctly. You need to restore via iTunes.
Apple TV (2nd and 3rd generation): Restoring your Apple TV
Make sure you follow the steps correctly (unplug all cables, connect micro usb, then reconnect power)
Connect directly to a computer, not a keyboard port or USB hub. Try a different cable -
After Updateing Firmware defult password is What?
Sir
i have router RV215W and i was update my router firmware to 1.1.0.5 . After finishing updation my router was restart than after i found wifi name is "ciscosb1" but old password is not work . So please tell me the defulted password after updateing firmware .Hi Udayaraj,
Even if you do a firmware upgrade the password wont get changed until and unless if you do a device factory reset.
once try cisco/cisco or admin/admin.
Thanks,
Phanikrishna -
I own a black macbook (early 2008 model) and for the past few months the display has occasionally (although recently more often) failed to turn on when booting. This only happens every one in four times after a full shut down. When I turn on the computer, I hear the hard drive boot and the fans start going, I also get a response in the white light indicator. When this occurs, I then have to press the on/off button to shut the macbook down, then press the button to turn it on again. Sometimes this works on the second try, but other times it takes 3 to 4 times turning it on or turning it off. Initially I thought it was a hard drive issue (and planned to purchase a new hard drive), but after connecting the laptop to an external screen, the desktop shows up (macbook display remains off despite unplugging or replugging external display). Is this a firmware issue? Or potentially a display cable issue? I'm leaning towards firmware since it only happens every 1 in 4 times. All parts in the macbook are original to 2008 and I've never really had any problems before.
I've tried resetting by taking out the battery/pressing the on button.
I also did a clean 7 pass wipe and reinstalled Mac OSX.
Used TechTool Deluxe - found no issues.
Booted computer and pressed D to perform a Mac hardware test - no problems found.
Not sure what to do now...
These two looked mildly like my problem: http://www.ifixit.com/Answers/View/68700/Not+booting+properly+after+10.6.8+and+F irmware+updates and another suggested replacing the display cable: http://www.ifixit.com/MacBook-Parts/MacBook-Display-Data-Cable/IF186-073?utm_sou rce=ifixit_guide&utm_medium=wiki_text&utm_term=if186-073&utm_content=product_lin kI own a black macbook (early 2008 model) and for the past few months the display has occasionally (although recently more often) failed to turn on when booting. This only happens every one in four times after a full shut down. When I turn on the computer, I hear the hard drive boot and the fans start going, I also get a response in the white light indicator. When this occurs, I then have to press the on/off button to shut the macbook down, then press the button to turn it on again. Sometimes this works on the second try, but other times it takes 3 to 4 times turning it on or turning it off. Initially I thought it was a hard drive issue (and planned to purchase a new hard drive), but after connecting the laptop to an external screen, the desktop shows up (macbook display remains off despite unplugging or replugging external display). Is this a firmware issue? Or potentially a display cable issue? I'm leaning towards firmware since it only happens every 1 in 4 times. All parts in the macbook are original to 2008 and I've never really had any problems before.
I've tried resetting by taking out the battery/pressing the on button.
I also did a clean 7 pass wipe and reinstalled Mac OSX.
Used TechTool Deluxe - found no issues.
Booted computer and pressed D to perform a Mac hardware test - no problems found.
Not sure what to do now...
These two looked mildly like my problem: http://www.ifixit.com/Answers/View/68700/Not+booting+properly+after+10.6.8+and+F irmware+updates and another suggested replacing the display cable: http://www.ifixit.com/MacBook-Parts/MacBook-Display-Data-Cable/IF186-073?utm_sou rce=ifixit_guide&utm_medium=wiki_text&utm_term=if186-073&utm_content=product_lin k -
Q10 Won't Turn On After Update
I am currently on Windows Phone and wanted to try Blackberry 10 as I am fan of my old Blackberry. I wanted to try it out cheap so I bought a Q10 on Ebay for $50 even though the seller said the phone had a water damaged sticker thinking I could fix it. I also bought a brand new battery from Amazon to go with it.
So my issue is when I got the phone, it was having trouble connecting to Link and reloading the OS would fail due to connection loss, so I nuked the phone with a program to clear the phone. I also soaked the phone in isopropyl alcohol after reading that soaking it could get rid of mineral deposits on water damaged phones. After the nuke and clean, the phone does the two quick blinking red lights which (I think) means the phone has no OS on it which is what I wanted after the nuke.
So, I plug the phone into the computer and Link recognizes it as a Q10. I have BB OS 10.2 downloaded and went to reload it. It completes the update all the way with a green LED on the whole time it is updating. When Link says to unplug the phone to let it reboot, the phone does nothing. Holding down power for any length of time can't turn on the phone. Plugging the phone into a wall charger causes the orange charging LED to flash on like it's going to start charging before quickly turning to a red LED while it stays plugged in.
I nuked the phone and tried Autoloader which does the same thing in the end as the phone won't turn on when it unplugs from the computer after updating. Seeing as how the phone is recognized by Link, seems to update correctly with the green LED on, and can be nuked fine, is there any way I can get this phone to work? It seems as though the battery isn't charging because once I unplug from the computer / wall, nothing seems to do anything and the LED doesn't flash. It is a new battery, so could the water have caused an issue on the circuit board which is not letting the battery charge?
Any help is appreciated, and I am willing to try pretty much anything and have decent knowledge of software / hardware. I have done tons of searching for similar issues to no success, but have not found this exact problem. Thanks in advance for any help!OK, you bought a new battery which I would recommend, and it still is NOT charging or powering on.
You've done this already >> Make sure you let it charge with the wall outlet charger for several hours and then with it still connected to the wall outlet charger, remove the battery and reinsert... what happens?
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code -
My iphone 4s cannot be turned on after updated to ios 7. can anyone tell me how to solve this
my iphone cannot be turned on after a week i updated it to ios 7. I have tried many solution to turned it on but none of them works. Now it only appear the apple logo on my screen since 5 hours ago. Can anyone suggest me the best solution
Hello Anis Squared,
I would be concerned too if my iPhone was not powering on. I found an article with steps you can take when you encounter an issue like this. I recommend following the steps below:
Will not turn on, will not turn on unless connected to power, or unexpected power off
Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion. Learn about LCIsand corrosion.
Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
After at least 30 minutes, if:
The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen . Then unplug the phone from power. If it immediately turns off, seek service.
The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.
If the display turns on, go to step 4.
If the display remains black, go to next step.
Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.
You can find the full article here:
iPhone: Hardware troubleshooting
http://support.apple.com/kb/TS2802
Thank you for using Apple Support Communities.
Best,
Sheila M. -
IBooks 3 fails to launch even after update
On my ipad 2, iBooks version 3 still fails to launch after update. This is the first time I can recall Apple failing to fix a material bug. I hope it is working on the problem.
iBooks is working fine on my iPad 2.
Lets try first quitting the iBooks app then resetting the iPad.
Go to the Home screen and double click the Home button. That will reveal the row of recently used apps at the bottom of the screen. Tap and hold on the app in question until it wiggles and displays a minus sign. Tap the minus sign to actually quit the app. Then tap anywhere on the screen above that bottom row to return the screen to normal. Then restart the app and see if it works normally.
Then reboot your device. Press and hold the Home and Sleep buttons simultaneously ignoring the red slider until the Apple logo appears. Let go of the buttons and let the device restart. See if that fixes your problem.
Maybe you are looking for
-
Importing gif animations into Elements 12 on Mac
Ok, I have searched quite extensively for a specific, accurate answer and am not clear about the conflicting responses I have encountered. To wit: I bought Elements 2 for a PC several years ago. It had two nice features for my enjoyment of making .
-
How to install firmware for the WRT54G
I have downloaded the newest firmware for this router, but the file is a .bin. There is no .cue, .iso or other file associated with it. How do I open this file, or burn it? I tried creating a .cue file using a .txt text editor: FILE "WRT54Gv5v6_v1.02
-
How do I locate the latest version of Camera Raw? I have a beta version of Adobe Camera Raw 8.6 that expired 2014-8-31.
-
My mac book pro shuts down just after it is started
My MacBook Pro shuts down straight after it has been started. A bar appears at the bottom of the screen that I've never seen before! A tiny part of it is filled, it disappears and the machine shuts down.
-
Hi Guys I use iphone with sw versio 3.1.2 (7D11) I was told that the new version 3.1.3, which is automatically offered, is not good one... Can some one comment on this Abraham Levy/Israel