SonyEricsson W 800 connectivity problems

I see no other posts re the Walkman 800i. So i started this one. I am having problems getting the W 800 i to stay connected to my G4 via USB 1. After transfering about 8 MB or so of info from the phone via USB I loose connectivity. And I usually loose control of my OS along w Mouse control. Everythig freezes. Except the phone. I can reboot both the phone and the computer and go another 4 to 8 MB or so and then it happens again. And again. Just for the record; if I just reboot the computer wout rebooting the phone then evrything will freeze up right away as I Photo trys to load the Walkman Any help out there? Is it the phone? Or is the OS just not up to phone compatibility yet? Any other Walkman users out there? How do I get I photo to quit tring to load the phone right away? This may be an I photo problem? I have I Photo set to be my viewer of choice for any attachable cameras.

The 1st step would be to repair the HD and Permissions, my recomendation is to use Applejack...
http://www.versiontracker.com/dyn/moreinfo/macosx/19596
Install it, reboot, hold down CMD+s as it's booting, at the prompt type...
applejack auto
Let it do all 5 of it's fixes.
Then we can get more detailed if you still have the problem.

Similar Messages

  • Firewire 800 connection problem

    Hi!
    So my warranty just expired a month ago. I went to get my mac fixed right before it and it came back with an issue with my firewire. No big deal really. I called back, they helped me fix it, but now it's doing it again.
    The external hard drive I connected to the FW8 port works fine. I've tried it with other cables (FW4 and USB2) so I know it's not the hard drive. However, when I try using the FW8, it does not show up at all. I have 2 different external drives and I've tried both of them. Last time when we fixed this, it turns out my mac was trying to boot from the disk or something? I can't remember... nor do I have any idea where to start to mess with the configuration. Help please? the disk is lighting up, so it is powering on... it just isn't showing up!

    I'm completely confused: you start by saying "The external hard drive I connected to the FW8 port works fine." Then in apparently complete contradiction you write:
    However, when I try using the FW8, it does not show up at all.
    What do you mean, "the disk is lighting up?"
    And:
    Last time when we fixed this, it turns out my mac was trying to boot from the disk or something?
    The Mac should be trying to boot from some disk.
    And then:
    I've tried it with other cables (FW4 and USB2) so I know it's not the hard drive.
    What does that mean? What is it in, "I've tried it....?" And, are you saying it works (which I suppose means the external does mount) using the FW4 and USB Ports?
    I know you have a real problem but I really have no idea what you are asking
    In case, as your topic suggests, you are simply asking about a problem with the Firewire Port, do what Roger suggested and have a look at this article.
    http://support.apple.com/kb/HT1151?viewlocale=en_US
    Message was edited by: WZZZ

  • Dial-up connect problem after 10.4.9 update

    After installing the 10.4.9 update it has been very difficult to connect to the dial-up internet server. It may take 19 tries clicking "Connect" before it connects and sometimes it connects after four tries. The error messages vary: unable to connect to PPP or no carrier detected are the most frequent messages. Once on-line everything works fine except for being able to send mail. I'm unable to send mail - that error message wants the SMTP server settings and any advanced settings checked.
    I called Apple support and the Apple Tech had me reconfigure the Network to dial an "800" number to a PPP Dial-Up Test Site. When that worked succussfully a window displayed a message that the modem, the PPP or Remote Access software, the TCP/IP software is functioning and correctly configured for a PPP connection to this server. The Apple Tech checked the information on the 10.4.9 upgrade and did not find any reason to think it would cause this problem. Apple Tech suggested I contact the dial-up server.
    The dial-up server went over all the configurations and they were all correct. During my phone call to them they could hear the computer dial-up sounds and said it sounded like the normal "hand-shake". The dial-up server has had no reports of problems with connecting to their service other than mine.
    If anyone knows what could have caused this problem, how to fix it or has the same problem I'd be very interested in hearing from them.
    Thanks, AppleProblem
    iMac G5   Mac OS X (10.4.9)   Power PC
    iMac G5   Mac OS X (10.4.9)   Power PC
    iMac G5   Mac OS X (10.4.9)   Power PC

    You have been most helpful and we think the problem is solved. After I send this message explaining what has transpired I'll go back and click on the "Solved" button.
    Based upon your suggestion to try "Script, like v32" I started experimenting with the four internal modem options we have in our Modem settings. They are v.32, v.34, v.90 and v.92. I tried to connect three different times with each one. The v.32 didn't connect, the v.34 connected all three times, the v.90 connected the first two but not the third or the fourth try. On the fifth attempt the Mac froze up, the mouse/arrow wouldn't work and there was a high speed motor sound. I tried a Force Quit (Option,Command,Escape), I tried a Hard Shut Down (holding the power key) and when these didn't work I pulled the plug. Then, I booted back up and connected on the second try using the v.90. I don't know why the computer froze up and assume it is nothing to be concerned about.
    I then called our ISP and found that the two access numbers are both v.90. I suspect that until we did the version upgrade to the 10.4.9 that our computer was accommodating the v.90 eventhough it was a v.92 (!?!). Just a guess.
    I also asked the ISP tech why we couldn't send mail. He asked if we had the password set for the outgoing mail. He said if we're using the access number owned by them it didn't require a password but the other access number is not owned by them and is used by other ISPs and it does require a password. We had never set up our Mail Preferences outgoing mail settings to use a password. Before our connect problems we had always used the number owned by them and after the connect problems we started using the other number because we found that we could connect to it with fewer attempts. We put in the necessary information and now have no problem sending mail.
    We have also been looking for another ISP and the web site you gave us www.fastermac.net looks very promising. They have one access number in our area and we want to check if it is v.92 or v.90. During our research for an ISP we learned that if it is a v.92 access number (and we use our v.92 modem) we'll be able to answer phone calls and remain online. That will be a real blessing. Thanks!
    We really appreciated your brain storming with us and your perseverance. Thanks so much!
    iMac G5   Mac OS X (10.4.9)   Power PC

  • Database connection problem when i try store the values in JTable

    Hi Sir,
    I have a database connection problem when i try to store the data's in a JTable.I think the problem is with in the database connection.I have used 3 vectors here.The database which i have used is
    Access.Where the program is compiling well.But when i run it only the first column heading is printed and error message showing that
    "Invalid Cursor State".I need to solve this problem.pls. do help me.
    I will provide u with the code.
    import java.awt.*;
    import java.awt.event.*;
    import javax.swing.*;
    import javax.swing.event.*;
    import java.util.*;
    import java.sql.*;
    public class DataBaseVector extends JPanel
    //Container contentPane=getContentPane();
    JScrollBar jsb = new JScrollBar(JScrollBar.HORIZONTAL);
    JScrollBar jsb1 = new JScrollBar(JScrollBar.VERTICAL);
    Image i1;
    String url="jdbc:odbc:Ananth";
    Vector col=new Vector();
    Vector rows=new Vector();
    Vector rdata=new Vector();
    Connection conn;
    public DataBaseVector()
    //super("JTable With ScrollBars");
    this.setLayout(new BorderLayout());
    UIManager.put("ScrollBar.track",Color.red);
    UIManager.put("ScrollBar.thumb",Color.blue);
    try
    Class.forName("sun.jdbc.odbc.JdbcOdbcDriver");
    conn=DriverManager.getConnection(url); // Is there any problem here?
    Statement st=conn.createStatement();
    ResultSet rs=st.executeQuery("Select * from AccountMaster");
    // rs is the result set obtained
    ResultSetMetaData rsmd=rs.getMetaData();
    int cols=rsmd.getColumnCount();
    for(int i=1;i<=cols;i++)
    col.addElement(rsmd.getColumnName(i));
    rdata.addElement(rs.getString(i));
    rows.addElement(rdata);
    }catch(Exception e)
         System.out.println("The Error Message was:"+e.getMessage());
    JTable jt=new JTable(rows,col);
    int v=ScrollPaneConstants.VERTICAL_SCROLLBAR_AS_NEEDED;
    int h=ScrollPaneConstants.HORIZONTAL_SCROLLBAR_AS_NEEDED;
    JScrollPane jsp=new JScrollPane(jt,v,h);
    this.add(jsp,BorderLayout.CENTER);
    this.add(jsb, BorderLayout.SOUTH);
    this.add(jsb1, BorderLayout.EAST);
    public static void main(String args[])
    JFrame jf=new JFrame();
    JPanel frame=new DataBaseVector();
    jf.getContentPane().add(frame);
    jf.setSize(800,600);
    jf.setVisible(true);
    Thanx,
    m.ananthu

    The problem is ResultSet.next() is not called.
    Try this and modify the table creation as you need.
    ResultSetMetaData rsmd=rs.getMetaData();
    int cols=rsmd.getColumnCount();
         while(rs.next()) {
              for(int i=1;i<=cols;i++)
                        col.addElement(rsmd.getColumnName(i));
                        rdata.addElement(rs.getString(i));
              rows.addElement(rdata);
    Hope this helps

  • Timeouts and connection problems after 5.1(2) upgrade

    AIM/chat and some other programs are having timeout/connection problems after upgrade to 5.1(2). I am using S241 also. The connection problems stopped when the IPS was set to bypass. Rebuilt IPS and left sigs at default settings and problem is still happening. I am not seeing any of the IPs that are having the problem in the Event Viewer or on the Events in the IDM.
    Any known issues with the 5.1(2) that would cause this type of problem?

    I don't know specifically, but I did notice that 5.1(3) was released today.

  • Hi, i am having trouble with my mac mail account, i cannot send or receive any emails because of the server connection problems. Message says it could not be connected to SMTP server. Thanks in advance for your help.

    Hi, i am having trouble with my mac mail account, i cannot send or receive any emails because of the server connection problems. Message says it could not be connected to SMTP server. Thanks in advance for your help.

    Hello Sue,
    I have an iPad 3, iPad Mini and iPhone 5S and they are all sluggish on capitalisation using shift keys. I hope that Apple will solve the problem because it is driving me crazy.
    I find using a Microsoft Surface and Windows 8 phone, which I also have, work as well as all the ios devices before the ios 7 upgrade.
    It has something to do with the length of time that you need to hold the shift key down. The shift key needs to be held longer than the letter key for the capitalisation to work. For some reason, this is a major change in the way we have learnt to touch type on computers. I am having to relearn how to type!
    Michael

  • RFC Receiver adpater Connection problem , Help us to solve ?

    Hi  Friends ,
                          Our scenarilo is Mail to RFC. It was running fine. In RFC Receiver adapter i have given <b>Maximium connection property to 1</b> .
                      While multiple set data passed to rfc will connection problem will come ?
                     Most data not uploaded . I am getting the following error.
                     <b>   If i set max connection to 5 . It is 5 times or more than that it is pusing the data .</b>
                    i am getting the following error <b>while i set the Max   connection to 1 .</b> . <b>Any other place i need to change configuration ?</b>
                   <i><b> - Error: 2007-09-24 10:51:22 GMT-05:30: Message processed for interface YRFC_EXT_WARR: com.sap.aii.af.rfc.afcommunication.RfcAFWException: error while processing message to remote system:com.sap.aii.af.rfc.core.client.RfcClientException: resource error: could not get a client from JCO.Pool: com.sap.mw.jco.JCO$Exception: (106) JCO_ERROR_RESOURCE: Connection pool RfcClient[CC_EXTE_WAREN_2W_RFC_RECEIVER]e7fa21f86ec535e883636c0beffc0f0c is exhausted. The current pool size limit (max connections) is 1 connections.</b></i>
                            Please give the description . I have referred many likns . Help us to solve this problem .
    Regards.,
    V.Rangarajan<b></b>
    Message was edited by:
            ranga rajan

    Hi,
    Have a look at this.This will help you.
    1.
    https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/f3f93ee7-0c01-0010-2593-d7c28b5377c2
    2. https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/3103eb90-0201-0010-71af-be6f4a6f61d1
    Regards,
    Akshay Jamgaonkar.
    Reward points if find useful.
    Message was edited by:
            Akshay Jamgaonkar

  • Unending connectivity problems -- and Desktop Help...

    I'm wasting so much time on connectivity problems that it's positively wearying. Prior to the installation of BT Infinity here in April, I had a low quality broadband service because of the length of the line from the exchange: if I could get a download speed of 1.2Mbps and an upload of a quarter of that, I was doing well. 
    BT advised that thanks to fibre optic, my Internet should run much faster. So we had Infinity installed. I'm registered with Speedtest.net so am able to see my performance record.
    The average download speed is now aroun d 6Mbps and the average upload, more than that at 7Mbps. How an upload speed can consistently be faster than a download escapes me.
    But I'm not familiar with the ways of Internet connectivity and try as a I might, can't get my head around it.
    This desktop computer runs Vista OS. Vista was **bleep** when it came out and is renowned for its botched handling of Internet connections. So I'm not blaming BT for the literally unending connectivity problems that are occurring now, with line drops, speeds slowing to a crawl, and no guarantee that any connection will last. But it would be good to actually use BT software to help fathom out what's going wrong here, and today's typical morning which looks like this:
    1) Boot up computer. Automatic connection to hub via Netgear USB wireless adapter. Hub is on ground floor of this 3-storey property but signal strength from hub  is excellent, as confirmed by inSSIDer monitoring, currently showing 54 with no other networks anywhere near that figure.
    2) Perhaps 5 minutes after connection established, it's then lost. 'Local Only' is displayed. This is, apparently, a known Vista problem. But Microsoft has issued a fix for it. I know this, because it took 100 hours of ploughin g the Net to find out that MS had finally admitted to one more Vista screw-up. I've used the Microsoft router "fix it" before and it didn't work ("failed to process") so uninstalled it and have DL'd it again now and run it. This time it says it has fixed everything.
    3) Computer is re-booted to make the fix effective. Computer connects to Internet. Speedtest.net check yet again confirms that upload speed is faster than download speed.
    4) Connection dies. So much for Microsoft Fix It.
    5) Windows diagnostics reports that it can re-set the IP profile (or something.) I click yes. The re-set goes through. Connectivity is restored. 10 minutes later, connectivity is lost. Just a red X in the tray. No connection of any kind, not even that daft 'Local Connection' only alert.
    6) Reboot. Yet again. BT Desktop Help was installed here and ran OK when we were using our Netgear DSG34 router. But since the change to the BT Hub, the BT program has never run at all. So-oo. . . It has been uninstalled. And then re-DL'd and re-installed. And though the installation  has been completed, clicking on 'launch' has failed to launch anything. But anyway. An hour ago, in one of the brief periods today when the Internet connection was holding up, I Revo-ed out the earlier install, DL'd BT desktop Help and re-installed it. . . and I'm still at the same stage as always, with a  Firefox browser page that's open and completely blank and has been for the past 30 minutes. The URL is:
    file:///C:/Program%20Files/BT%20Broadband%20Desktop%20Help/btbb/Start.html
     Repeated page re-loading gets nowhere. Malwarebytes PRO is turned OFF to prevent any possibility of blocking and the antivirus is termporaily SUSPENDED. This PC runs on Windows standard firewall but even turning that OFF doesn't get the page to load. Copying the address into Internet Explorer in case there's a Firefox problem merely results in Firefox being opened and the same blank page running there.
    7) After all that. . . Connection lost yet again and this time, Windows cannot connect at all. It reports that the "wireless network security key is not correct". I happen to know that it is, because this is maybe the 20th time it has reported this in the past 10 days and every time I have to key in the "correct" key all over again. . . at which point Windows still says it isn't correct and cannot repair.
    Turning off the computer completely, unplugging from the wall, holding in the power switch for a full minute to clear the circuits, traipsing up and dowen three flights of stairs to turn off the hub, then wait, then turn the power back onm again. . . Ah, wot fun times I'm having here with my particular versioin of Infinity (as in, an infinity of connectivcity problems.)
    Summary: I seem to be being simultaneously hit with one issue after another.
    I'm bewildered as to why ever since Infinity was installed here, my upload speed is generally faster than my download speed. I'm not happy with endless Internet connection failures though am thinking that Vista is playing a large part here with its "wrong security key" and unending 'Local Only / Limited Connection' failures. I do miss my Netgear router and the ability to access a fantastic help menu and re-boot directly from the desktop without having to keep going up and down three flights of sdtairs to do so (I haven't been able to find out how toe access the BT Hub remotely.)
    Above all though: I'm  really tired of repeatedly trying to run freshly downloaded and installed BT Desktop Help software but getting no further than a blank page because the program has stalled.
    If anyone has any advice / suggestions, other than to buy a carrier pigeon, that'd be much appreciated.
    Thanks.

    Thanks again to John and gg30340. Here's an update:
    1) BT Desktop Help removed completely from this computer. The uninstaller itself mopped up everything, which surprised me. But anyway.
    2) Bt Home Hub manager set up and working. Had to input serial number and create new password. All of this sounds fairly easy and would be if one had the device near the desk. But the idiots who built this property shoved the BT master socket inside the garage next to the door. Our two home computers are on the third floor. To ensure the wireless signal strength is OK, the Hub and Infinity module/device/whatever it's called are on a high shelf. It's a major job to even reach the darn things, never mind read the labels seeing as how the BT Infinity engineer was good enough to tidy up the cabling and make a very tight connection to the wall socket.
    3) I had hoped to be able to back up the Hub's settings, seeing as the software provides for Advanced Settings / System / Backup. But not on mine (Hub 3.0). All that System allows is choosing which internet clock to define the accurate time. Everything else in System is just a pattern of short lines as if trying to indicate that there's some text there but it's invisible.This is now my second encounter with BT software which, for whatever reason, isn't functioning as it should on this PC.
    4) Hub reset to factory fresh, according to BT guide.
    5) Reset appears to have achieved nothing apart from requiring the password to be popped in again. After reset, it wasn't even possible to connect to the hub manager. Internet connectivity was eventually established for all of 30 seconds and then, gone.
    6) Computer was shut down and then booted anew. Internet connectivity is still. . . dreadful. One minute everything's fine and then, literally,. the next minute a webpage won't load. Even opening the Hub Manager has taken three attempts, i.e., disconnecting from the Internet, re-connecting, failing, and trying twice more until success. Yet all the time these failures are occurring, the tray icon is showing a steady, unwavering green icon for Local and Internet access -- despite the fact, there manifestly isn't any.
    7) Speedtest. net tests are actually showing upload and download 'trajectories' going slower and slower and finally halting at some point on the arc, then after a period of up to 30 seconds, suddenly becoming animated again. Speed test results with broadband speed checker UK and Think Broadband's checker are so at variance with one another, and with Speedtest, net, that it seems all three are using different technologies in pursuit of the same thing. Either way, upload speeds continue to be much, much faster than download speeds, a state of affairs I certainly have never encountered before.
    8) Speedtest net tests taken in the past 10 minutes, with one test following on from its predecessor, begin at 8.24 down/8.88 up, followed by 5.24 down / 6.40 up, followed by a mind-numbingly lonnnnng 0.62 down / 8.70 up -- in other words, a continuous yo-yoin g of Internet connectivity to the pooint that it actually might as well not even be here (I've had to make five attempts just to get on to this forum. . .)
    9) BT Speedtest will necessitate disconnection of everything downstairs and all boxes being lugged up here. This is actually going to require uncoililng tied-off cabling and hanging off a stepladder to do so -- though I surely can't be the only person in Britain who doesn't have a nice, handy BT master socket in their study or lounge. That said though: until we switched to Infinity, we *never* experienced these kinds of horrendous connectivity problems and never had need to unplug the Netgear router downstairs and bring it upstairs to connect directly to tjhe desktop PC so BT's own test could be run.
    I'll just have to get to work dismantling stuff tomorrow. However, I have to say that after a factory re-set which has changed nothing at all, I'm beginning to think there's a problem with the BT line itself (hence why I'm happy to follow the advice here, though less than happy at the prospect of the messing about involved.)
    Thanks, you two, for your patient help, and also for clarifying the situation re the three signal paths being shown on inSSIDer. At least I know that's usual now! And now, hopefully, when I press 'Post', I won't be faced with an endlessly spinning Firefox circle culminating in  what may well be, or seem to be, the 57,938th time today of seeing "Page Not Found". . .

  • PHP and MySQL Connection problem

    I am trying to make a PHP MySQL on a remote server connection in Dreamwesaver CS3.
    When I enter the information (host, user, password, etc.) and hit TEST, I get the following error message.
    "Access Denied. The file may not exist, or there could be a permission problem. Make sure you have proper authorization on the server and the server is properly configured."
    I know the user, password, etc. work, as I can access the MySQL database with other software.
    I checked with my host and they say there are no permission problems on their end.
    I have checked the settings on the Test Server page in Site Setup and everything looks correct and works there.
    I have not seen this particular problem described in other forum postings (although there are a LOT of postings on this topic!).
    Any help would be appreciated.

    I thought my testing server was the remote server and is always on as far as I know. I don't know how to turn it on or off.
    Is there some other testing server that I should be aware of?
    Frank
    Date: Wed, 3 Jun 2009 15:43:02 -0600
    From: [email protected]
    To: [email protected]
    Subject: PHP and MySQL Connection problem
    I know you are using remote, but is your testing server on? if not turn that on and see if that does it. it just happened to me working on remote server and could not get mysql conn to work, until I turn on my testing (developer server), then I was able to connect to mysql and the tables that I created in phpmyadmin remotly was downloaded.
    >

  • TS1538 my ipad can not continue to download ios 6.1.2 because of connection problem and it is stuck in connect to itunes image, i cant open it anymore..what should i do? help plz

    my ipad can not continue to download ios 6.1.2 because of connection problem and it is stuck in connect to itunes image, i cant open it anymore..what should i do? help plz

    Connect to iTunes on the computer you usually Sync with and “ Restore “...
    http://support.apple.com/kb/HT1414
    If necessary Place the Device into Recovery mode...
    http://support.apple.com/kb/ht4097
    You may need to try this More than Once...
    Be sure to Follow ALL the Steps...
    But... if the Device has been Modified... this will Not necessarily work.

  • I am experiencing wireless connection problem on 4s after ios 8.1 upgrade. The wireless icon appears showing that it's connected but webpages do not load. I have checked my internet connection with other devices and seems to be alright. what to do?

    Hi
    I am experiencing wireless connection problem on 4s after ios 8.1 upgrade. The wireless icon appears showing that it's connected but webpages do not load. I have checked my internet connection with other devices and seems to be alright. what to do?
    I have tried reseting the network settings and forgetting my wireless connection and re-connecting to it. I even backed up my phone on itunes and restored it, factory reseted it. Nothing seems to work.
    Also after my upgrade to ios 8.1 my personal hotspot option under cellular data has disappeared.
    Would you please help me out? I would really appreciate it.

    Hi..
    Restart your router then restart the iPhone to test.
    If that doesn't help, try this support article >   iOS: Troubleshooting Wi-Fi networks and connections

  • Network connection problems, please help!

    I have had an iPod Touch (4th generation) for over a year now and it worked fine. Today, something went wrong with my network connection. One moment it says that I'm connected to a network, and a few seconds later it says I'm not connected... Then a few seconds later it's connected again. I have full wifi bars, and it does it throughout my whole house. The wifi symbol keeps going on and off. I tried turning my Verizon Westell Model 6100G Modem off and back on because this normally fixes my wifi connection problems. This didn't work. Then I tried turning my iPod off and back on. This didn't work. I tried turning the wifi off and back on. This didn't work. I tried forgetting my network and signing back in. This didn't work. I also tried resetting the network, and this didn't work either. I'm not having any connection problems with my laptop, it's working fine. It's only my iPod. I'm still able to use the wifi, but for a split second, it will not work. I'm not sure what else to do. It's very annoying! I'm going to see if it does this at other peoples houses with their wifi. Can any one tell me what's wrong and how I should fix it? My only theory is a broken antenna...Please help! Thanks!

    I have two things you could try.
    1. Plug your iPod into the host computer that which the network is based around because sometimes the network has trouble identifying a device if it has been a while since you plugged it into the computer.
    2. Find some way to get your network information (IP address, Subnet Mask, Router, DNS numbers) from another device on the network (e.g. laptop). Then go to Settings > Wi-FI and find your router and tap the blue arrow to the right of the name and tap the tab that says "Static" and enter this information accordingly. Then exit back to the network names menu and re-enter your passcode for your network (assuming you have a passcode)

  • SAP Crystal Reports data source connection problem using sap business one

    Hi,
    I m facing a problem regarding: SAP Crystal Reports data source connection problem using sap business one
    I am trying to create a Crystal report but when I try to configure a new connection it does not work.
    I select Sap Business One data source and try to complete the information required to connection but it does not list my companies databases, what is the problem?
    Our Current SAP related software details are as follows:
    OS: Windows Server 2008
    SAP B1 Version: SAP B1 9 (902001) Patch 9
    SAP Crystal Report Version: 14.0.4.738 RTM
    Database: MS SQL Server 2008 R2
    I have also added some screenshots of the issues.
    Please have a look and let me know if you have any questions or any further clarifications.
    I m eagerly waiting for a quick and positive reply.

    Hi,
    There is problem with SAP Business One date source.
    I had faced same problem, I used OLEDB Data-source, and it worked fine for me.
    So, try to use OLEDB.
    Regards,
    Amrut Sabnis.

  • WiFi Internet connectivity problems after upgrade to 10.8.4

    After upgrading to MacOS 10.8.4 I am facing regular interruptions to my WiFi internet connectivity. Periodically the internet connectivity is lost and the only way to fix the problem is to turn WiFi off and on again. This happens frequently when I am downloading files at using big bandwidth (more than 1.5-2 MB/s). If I use assist me on the Network preferences tab, it displays an ISP error when the connectivity is down, however I am certain that I do nota have any kind of ISP or router issue since at the same time I have WiFi internet connectivity from my iPad mini, iPhone 4S and Samsung Galaxy S3. Therefore it should be a 10.8.4 issue

    Troubleshooting Wi-Fi issues in OS X
    Wireless Connection Problems - Fix
    Wireless Connection Problems - Fix (2)
    Wireless Connection Problems - Fix (3)
    Wireless Connection Problems - Fix (4)

  • Lumia 900 Cellular Connectivity problem (AT&T) aft...

    I've had a Lumia 900 on AT&T for about 5 months and have not had any connection problems.  However, after the Tango update (OS *.8779.*; Firmware: *.12223), when I take my phone into work (which has no cellular reception normally) for an extended time and then take it outside it will sporadically not reconnect to the cell tower.  It will show no connection forever.  If I turn airplane mode on then off or turn off and then on the data connection, which seemed to fix similar problems before, I still get no connection.
    The only solution is to restart my phone.  One time it kind of hung on restart.  The other time the phone froze up when I was trying to turn on/off the data connection.  Restarting brings the cellular connection back. (Almost as if whatever software is controlling the cellular connection is crashing). 
    *I also installed the beta Nokia Counters program after the update -so that may be the problem too?
    Has anyone else experienced this before.  Is it a Tango issue, or a common issue that coincidentally started for me after the update?

    I am having a similar issues with Wifi & cellular connectivity Issues. In addition, am seeing that my Lumia 900's screen is turning black with no response from the power button or any other buttons (bottom buttons will be light though). I have to reset the phone by pressing volume power camera buttons. And one or two times today it had issues restarting cycling the Nokia logo, AT&T logo, then black screen about three to four times before it showed the Windows Phone logo to fully boot up.
    Totally Disappointed. 

Maybe you are looking for

  • Dissolves Flicker

    Hello, I've been editing Red footage brought in through Log & Transfer at 23.98 and 2048 x 1152, ProRes HQ. The footage looks great and plays in the timeline without rendering. However, my dissolves seem to flicker, especially if they go between brig

  • In iPhoto '11, is there a way to switch sizes of books after already having it ready to print?

    I created a print project for a book of photos.  Now I want to change the size of the book without having to redo it all.  Is there a way to do that?

  • Setting webserver settings project specific

    The Webserver settings are set in the project explorer (or in the VI) in the Tools/Options menu. However, the settings do not only apply to that VI or project but also to any other project that is opened afterwards. Is there any way that these settin

  • Link to access

    i have a database named login... and under this database... i have 2 tables...called detail and login, how can i link to table "detail"...thanks

  • How do you export LabVIEW SignalExpress Log files into MatLab?

    I am using SignalExpress to capture vibration and acoustic data.  I need to show the results to a customer that doens't have access to LabVIEW.  They have Matlab, so I need to find a way to export the SignalExpress log file into a usable format that