SOP mass processing problem

Hi All,
I am working on flexible planning in SOP.. I am trying to transfer the SOP plan to demand management through mass processing function..
I have done the following...
I created transfer profile through MC8S
i created activity through MC8T and assigned the transfer profile created earlier..
then created a mass processing job through MC8D and then finally scheduled it... SOP plan is not getting transferred to demand management.
I am getting the below error...
When I transfer the plan manually through MC90 for each material transfer is successful...
why the plan is not getting transferred through mass processing.. can somebody help me out...
Thanks
Kumar

Hi,
Thanks for reply.. our planning periodicity is weekly buckets....
I am sending the screen shots of the same....
Screen shot of planning type...
Screen shot of MC8D...
I have entered plan in weekly buckets
Now this is not getting transferred to demand management...
Can you help me out...
Thanks
Kumar

Similar Messages

Mass Processing for Forecast SOP

Hi Experts,
I have one requirement, I have to run Mass Processing for Forecast SOP in background Job based on consumption values updated in Material Master.
I have followed all instruction give for doing this process (SAP SOP Mass Processing - SAPs'WORD - We SAP For Your Cause) but could not achieve.
Can any one help to run in background job for Mass Processing for Forecast SOP.
Thanks in Advance
V.Sundeep

Hello,
Refer KBA 1778072 - Error message MA 653 when running mass processing forecast (program RMCP6BIN)
Internal condition NOT IPRWA-VGVON IS INITIAL not fulfilled
Internal condition NOT IPRWA-VGBIS IS INITIAL not fulfilled
Forecast/historical period cannot be calculated MA 653
Check your planning type which is used for your batch job. The number of historical periods in planning type (transaction MC8B) must not be smaller than the number of historical periods in forecast profile (transaction MC96). If the number of forecast period is maintained in the forecast profile (transaction MC96) the number of future period in the planning type must not be smaller than the number of forecast period in the forecast profile.
A not appropriate entry in SOP User Settings (transaction MC79) in Number of periods in the planning horizon can have an effect on this also.
Best Regards,
R.Brahmankar

Problem in COHV with mass processing function Release.

Hello,Guru's
I have problem in COHV with mass processing function Release.
even after execution of COHV the status of Orders remains unchanged.i.e. remain Created instead of Release
My user require all Orders should release in mass process
with material availability Check .
and OPJK setting is
material availability
Check availability during order release=X
Release material = 1(User decides on release if parts are missing)

> with material availability Check .
> and OPJK setting is
> material availability
> Check availability during order release=X
> Release material = 1(User decides on release if parts are missing)
Hi,
With these two settings in OPJK, there will not be any impact on COHV.
Any dates, date ranges you are inputing in the COHV.
Try with Manually inputing some of the Orders in COHV and in the Foreground you try.
Afterwards, try with Some selected Orders in the Background..
You may get the clue for the problem..
Regards,
Siva

Mass processing for SOP

Hi,
I am able create sale plan through MC87 transaction by selecting the create sale plan through forecasting, when total consumption values are maintained in the material. But I want this to be done by MASS processing function. In other words I want to up date key figure sales in S076 table.
There is one tcode MPBT which is to create total forecast in background. But this is happening only when unplanned consumption values are maintained in material. Is this behaviour is correct?
Can u detail the configuration settings required for mass processing of SOP.
Through help I came to now that mass processing can be done for forecasting. Is this forecasting and creating sales plan are same. Kindly brief.
Thanks & Regards,
N. Laxman

you can refer the below link:
[http://help.sap.com/printdocu/core/Print46c/en/data/pdf/LOLISPLN/LOLISPLN.pdf]
configuration steps for SOP:
1)Set parameter for Info structure and Key figure
2)Maintain Transfer Profile
3)Define Activity
4)Define Key figure assignment
5)Define copy profile.
procedure of Standard SOP:
1. Create Plan in inactive version
2. Disaggregate product group plan & Check capacity
3. Version Management
4. Transfer Product group to planning
procedure of Flexible Planning:
1.Create Plan in inactive version
2.Convert Plan in to Active Version
3.Transfer to Demand management
Master Data in SOP:
1.Information Structure
2.Planning Type
3.Planning Hierarchy
4.Product Group
5.Resource
6.Rough cut planning profile
It's very helpful link & std procedures for SOP.
SOP steps have 3 classifications
1) STD SOP for Material
2) STD SOP for Product Group
3) Flexible Planning
A) Now Let we take STD SOP for Material
This will takes place in Material and Plant level
so the charateristics will be Material and Plant
The key figures are Sales,Production Qty,Targer stock level,.......etc
Steps
1) Create Planning for material MC87
2) Copy to Active Version MC78
3) Transfer to Demand Mangement MC74
B) STD sop for Product Group
Here also the Characteristics are same material->product group
You have to maintain master data Product group
steps:
1) Create Product Group MC84
2) Create Plan for Product Group MC81
3) Disaggregate Product Group Plan MC76
4) Copy to active version MC78
5) Transfer to Demand Management mc75 for Pg or mc74 for material
C) FLEIXIBLE PLANNING
Here you can able to Define your own characteristics and Key figures
Char like Sales org,Dis chann, Div,......
Key figures like stock,invoice qty,....
steps
1) Create Info structute MC21
2) Maintain Planning Parametes MC7F
3) Create Planning Type MC8A
4) Create Flexible Planning MC93
5) Copy to active version MC8V
6) Transfer to Demand managemet
5) Create Std SOP Planning -MC
6) Transfer to DM from change mode of Flex Plann with active version MC94
if you want use the flexible planning info like SIS in std sop after the 4th step of above it will be like
5) MC87 std sop there Sales data from SIS it will ask for info str and version then you can get it automatically then the std steps like
6) Copy to Active Version MC78
7) Transfer to Demand Mangement MC74
Pls let me know any clarifications.

Mass processing for forecating in SOP

Hi all
I ma able to forecast a material online thru MC87 in standard SOP, but when I try to set up a variant for mass processing in the background the forecasting does not work. Has anybody encountered this issue?
thanks a lot

Tajuddin
Thanks for your reply. I am reading the R/3 documentation and it talks about Mass processing of SOP forecasting ( R/3 documentation verbiage below) I am trying to follow these steps but it does not work. Isn't this mass processing supposed to be for forecasting in mass in background?
Am i understanding this incorrectly?
How to Run the Forecast with Mass Processing
You can use SOPs mass processing function to run the forecast. In this process:
You create a forecast profile.
You create a planning activity and include in it this action (the forecast profile).
You create a mass processing job for this activity.
You schedule this mass processing job.
The results of the forecast will be different if the forecast is run at a high level and the results then disaggregated to the detailed level than if you carry out the forecast at the detailed level.

Mass processing of Workorders-Reg

Hi,
We are having standard Tcode COHV for mass Processing of Production Order.
Like that do we have any tcode for mass processing of Workorder.
The reason behind is instead of having CO99 for closing the order with only one plant(my requirement is multiple plants and multiple order types) ,Is it possible to use IW38 in Background to change the order from TECO to CLSD.
Because the option is given in IW38(Menu- Program-Execute in Background).If so how to do that?
Pl throw some light on this.
Regards
KRISHNAN

Krishnan,
In my 4.7 A&D IS system, we don't even have a menu path starting with Program in IW72 or
IW38 (Menu- Program-Execute in Background).
Only Order > Completion > Complete business, but these programs are designed to release, TECO etc all from within the transaction.
Additionally, you are not restricted to one plant and one order type in CO99. You can leave these open, you are then only restricted by one Controlling Area.
Problem with that is that you are not restricted to PM orders, all order types are processed.
If you are using PM task lists in all your orders, that may work for you as a selection criteria, but that's an unlikely case.
If not, you should be able to reach an agreement with all internal order type users that all orders should be (financially) closed after n days in state of TECO.
Most companies are keen not to leave any 'finished' orders open and available to financial postings.
The usual late postings are differences in invoices and purchase orders. If there are a lot of these it is practical to wait a number of days and then close.
The errors that occur afterwards can always be processed by reversing the closure.

Mass Processing errors

Hi Experts,
I am doing mass processing of process orders through CORM transaction, its showing errors for some orders,
The errors are,
1. Balance of ORD 1000010 is not zero
2. Unprocessed future change recs for order 1000012 prevent del. flag/completion
3. System status CRTD is active (ORD 1000220)
Please explain me in details the solutions for all the above errors.
Thanks & Regards,
Karad D D

Hi Devidas,
1. Balance of ORD 1000010 is not zero.
For this please get in touch with Costing persons. Orders are not yet settled. hence this problem is there.
2. Unprocessed future change recs for order 1000012 prevent del. flag/completion.
Few transactions are open for this material please close it.
3. System status CRTD is active (ORD 1000220)
Please put status TECO for this orders this will solve your problem.
Please confirm,
Regards,
Amit Kulkarni.

Using mass processing - transaction wtymp_a

Hi all,
I am trying to use the mass processing tool of WTY and I have some problems
I have created an action, when operating the action from transaction WTY it works fine but with the mass processing tool the action produce a dump and errors.
While debuging both transactions i have found that the action is called from different programs and there different checks made by sap on the data.
does any one have any idea?
BR,
Naama.

Hi Naama,
true, the call points are different. The main difference is that you have the UI available in transaction WTY. While processing in WTYMP you do not have the UI. Thus you need to make sure that you do not send any popups (can be i-messages, too) during mass processing.
Additionally it might be that your action does not correctly select the version it needs to work with.
Best regards
Christian

Mass processing & Back jobs

Hi Gurus
Can any one give me different background jobs and mass processing available in R3.
This is reqd urgent
Regards
Subbaraya

Mass Processing of Production Orders
Use
Mass processing enables you to carry out functions for multiple orders.
Features
Functions
The following lists contain the mass processing functions that are available:
Order headers
Material availability check
Release
Printing of shop floor papers
Costing
Scheduling
Generate capacity requirements
WM material staging
Picking
Set/delete user status
Confirmation
Technically complete
Close
Log display
Operations
Release
Print shop floor papers
Picking
Set/delete user status
Confirmation
Log display
Components
Print shop floor papers
Picking
Log display
Production resources and tools
Printing of shop floor papers
Log display
Starting Mass Processing
Mass processing can be started in the following ways:
Triggering the execution of a function
The execution of a function can be triggered as follows:
Execute function immediately
The functions are executed directly after mass processing has been triggered. This can take a long time for functions that require a lot of system resources. However, you can immediately check whether the function was successfully executed.
Execute function with dialog transaction
Further processing is controlled by a dialog that is specific to the function. This option is available for the following functions: Confirmation, Picking, Log display.
Create a function request (refer to Processing Requests)
First, requests are created without any further checks. The requests are created very quickly. Mass processing is actually executed with the program COWORKDISPATCH. As a result, it is delayed until the next time the program starts. You can decouple the function in terms of time, so that the main work takes place at night, for example. The end users create requests and system administration takes care of their execution.
Execute function in the background
First, requests are created without any further checks. Then a background process is started, which processes these requests immediately. Scheduling a background job does not create any administrative work and reduces the workload for the dialog.
Parallel Processing
For parallel processing, you define server groups for mass processing (COWORK-DIALOG, COWORK-BATCH). This enables you to speed up the execution of processing.
Mass processing online/ in the background.
You can either execute mass processing online or you can schedule it in a background job (no online steps are possible).
Application Toolbar with Mass Processing Functions
You can define that an application toolbar, with selected mass processing functions, is displayed in the list of the selected objects. You can use this application toolbar to execute the functions in the dialog.
For more information refer to Display Application Toolbar with Mass Processing Functions.
Test Run
You can decide whether changes caused by a mass processing function are executed in the form of a test run only. Error messages that may occur are collected. No changes are updated to the database.
You can use the test run for these functions:
Close
Set/delete user status
Release
Costing
Generate capacity requirements
Technically complete
Scheduling
WM material staging
To test a function, select the option Test function without changes to data on the Mass processing tab page.
Log
Log records are written and saved as a function is being executed. They provide information about the execution of a mass processing function. If no log record exists, the function was executed without any problems. The log records are assigned to the order or the collective order
Regards,
nandha

HCM P&F - Mass processes Fast Data Entry Error

Hi guys,
I have a new requirement to do a new mass process to save some IT data on several employees without Workflow related. First of all I have tried to understand how standard is working and I have checked one of mass process that system provides, in my case HR_PA_XX_MSP_ADDR_CHANGE process.
Unfortunately, when I execute start application ASR_MASS_START_PROCESS (configuration ASR_MASS_PROCESS_CONF) and select my process and more than one employee I'm getting a dump. This issue is not happening if just select one employee.
I'm going to attach some screenshots to clarify steps that I'm following.
Anyone has faced similar issues? It seems is a standard problem and I want to get some thoughts of you!
Regards

Sorry, I don't get you.
When selecting employees there is no issue there, my issue is when I save the data once I have selected more than one employee.
Regards

Mass Processing pop up in BI 7.0

Dear Experts,
I am getting popup window "mass processing" while doing status not ok(RED) for some delta loads in monitor screen(Before going for Repeat delta)
Here it is asking for :
" 2 Infoproviders still have to be checked ?
Interactive or Automatic (without asking for confirmation)?
Which option i need to select ? What is Interactive & Automatic ? I haven't seen this popup earlier. What could be the reason for this popup screen ? Please suggest how to proceed in this case .
Thanks & Regards,
Pcrao.

Hi,
One option I thought of, but never applied in practice. Create an excel with all the field related information in the structure of table,
RSDIOBJ Directory of all InfoObjects
RSDCHABAS Basic Characteristics (for Characteristics,Time Characteristics, and Units)
*RSKYF Key Figures
RSDTIM Time Characteristics
RSDUNI Units*
And upload this table with the flat using function module etc.
But then you would need to update below tables to with relevant details.
RSDIOBJT Texts of InfoObjects
RSDIOBJ Directory of all InfoObjects
RSDIOBJT Texts of InfoObjects
RSDATRNAV Navigation Attributes
RSDATRNAVT Navigation Attributes
RSDBCHATR Master Data Attributes
RSDCHABAS Basic Characteristics (for Characteristics,Time Characteristics, and Units)
RSDCHA Characteristics Catalog
RSDDPA Data Package Characteristic
RSDIOBJCMP Dependencies of InfoObjects
RSKYF Key Figures
RSDTIM Time Characteristics
RSDUNI Units
Edited by: Parth Kulkarni on Jun 22, 2011 4:56 PM

Mass processing by T.code COOIS

Hi,
How can I execute some mass processing in the T.CODE COOIS and not only reporting.
I canu2019t use u201Csettingsu201D and u201Cmass processingu201D in my system. They are deactived. Do I need some customizing.
Thanks
Dede

Hi Glenn,
Please use COHV - Mass processing by which you can execute the required changes.
COOIS is purely used to collectively get the desired reports for the discrete production process( production orders, etc)
Hope this clears your question.
Thanks & Regards,
Abhijeet Guha

QAC2 in mass processing

Dear Experts,
I know the transaction QAC2 for transfering inspection lot qty from plant to plat or storage location to storage location.
When it is executed for an inspection lot and SL is changed or plant is changed a material document of mvt-323 is generated for each individual posting.
But is there any transaction for mass processing of this activity and to create only one material document for bulk inspection lots.
If any one knows about this, please update ASAP
Regards
Vivek

There is no std SAP T- code available which could process this in Mass .

Mass processing

HI,
Is it possible to st the Deletion flag to the process order through mass processing.
Regards,
Amit

Hi ,
Thanks for the reply.
Actuallay in my senario we have a user status NDLF - No deletion Flag.
So in mass processing i want to deactivate the NDLF status and want to activate the DLFL status. we are scheduling background job monthly once to do this activity.
So i was just trying through COID / COHV / COHVPI. Whether it can possible or not.
But in COID mass processing we can update user status NDLF but we can not update DLFL deletion flag.
So i need to run 2 different variant
1 for Removing NDLF stataus through COID and
2 for Updating DLFL status through program .
Do you have any better solution than this.
Regards,
Amit

Mass Processing of Planned orders

Hi all,
We can do mass availability check for the planned orders and we can firm the planned orders for which the materials are available through COHV but can we have a output log after the mass processing so that we can see the list of planned orders got firmed and for any other messages.
Regards
Kumar

Dear,
In COHV or COMAC.
in mass processing gtab page
select function = material availability check, execute it.
In selection tab page
Plant
Order type
System status - MSPT.
Or
Start the report PPCOXPR1 with the T.code SE38
Then try with Tcode CO24..
Regards,
R.Brahmankar

SOP mass processing problem

Similar Messages

Maybe you are looking for