Sound and video accelleration won't work on OS 9.2.2

Hi,
I have an iBook G3 (16 VRAM), and I recently used a roundabout way of installing Mac OS 9.2.2 (used Classic within 10.4.7). When I boot the iBook from OS 9, two things that don't work are video accelleration and sound. Can anyone help me get them working? The sound chipset is the Texas Instruments TAS3004.
iBook G3 (16 VRAM) Mac OS 9.2.x 600MHz, 30GB, 256MB, CD-ROM

Hi, Malcy. The error message you report seeing will normally appear if one has copied the System Folder from an Apple installer CD onto a hard drive and then attempted to start the computer from it. That is not a proper OS 9.x installation procedure and will not work. If you tried that approach before you followed the correct installation instructions, the residue from that improper installation may be prompting the error message now, and the remedy may be removing all traces of OS 9 from your hard drive, then following the correct procedure again.
To remove OS 9 without being obstructed by a message that it is in use, drag the Finder and/or System files out of your OS 9 System Folder onto the desktop, then restart your Mac. Now trash the System Folder and the two files and empty the Trash. Finally, follow the correct OS 9 installation procedure again.

Similar Messages

HP DV1000 Sound and Video Drivers Won't Install

I just had to reformat my DV1000 due to a corrupt Windows XP installation. I downloaded the drivers from the HP website but they will not install, it just says FAILURE at the end of attempting to install them.
The p/n of my laptop is ED338AV. Any help would be greatly appreciated!!
This question was solved.
View Solution.

Hi,
All drivers for Your model are here.
First install chipset driver and reboot. here
Before installation of sound driver remember about installing MS-UAA first here
When You will do that start installing other things.
If You will still have any troubles write first which SP are You using on this XP system. SP1, SP2 or SP3?
** Say thanks by clicking the "Thumb up" icon which is on the left. **
** Make it easier for other people to find solutions, by marking my answer with "Accept as Solution" if it solves your issue. **

HT4557 I have iPad 2 and trying to connect to apple tv. Have gone into videos and music and put in my apple id and password but won't work. Pick up my PC fine though

I have iPad 2 and trying to connect to apple tv. Have gone into videos and music and put in my apple id and password but won't work. Pick up my PC fine though.
Any ideas? Have tried usual switching on and off again but no change

Here’s what you need to do to turn on AirPlay Mirroring on your iPad 2:
– Have iOS 5 installed on your iPad 2
– Make sure your Apple TV software is up-to-date. You can check for updates on the Apple TV by going to Settings > General > Update Software.
– Have your TV turned with Apple TV active and showing.
– Double-tap the home button on the iPad to bring up the Multitasking Bar.
– Swipe to move to the left of the Multitasking Bar, so you can see the set of controls just to the left of the volume adjustment slider.
– The button just to the right of the Fast Forward button – the one that has a rectangle with a solid, upward-facing arrow in it – is the AirPlay button. Tap to switch from iPad to Apple TV.
– Once you do that you’ll see the Mirroring section appear just below the entry for Apple TV. Just tap to turn that On, and the iPad 2 will immediately begin mirroring to your TV screen.

Onboard sound and video IRQ prob

Well I have norrowed down a prob I believe is with the sound and Video using the same IRQ.
Both are using irq 16...
Why windows would put them on the same irq is beyond me.
Is their a way to change this?
Mobo is KT4 ultra with c-media sound
video is geforce4 ti 4200
System keeps rebooting when in games.
I just did a fresh install and installed drivers and bleh same thing.
I also turned off plug and play in bios. which microsoft recommends.
Any help would be great
r00t 3:16

Well considering their is a alot of IRQ's and half of them aren't in use you would think ms would not assign a video and sound to the same irq.....
At any rate. Im not sure what games you play but most games check to see if your sound card is working before it loads.
So that won't work.
I didn't have any problem with this system until I formated and redid everything I should of just stayed with it as it was.
Then the sound was on irq 16 and the video went to irq 128?
Thats right 128....
I didn't have to disable APIC either.
Although I did however have plug n play support disabled in the bios.
I also installed all drivers and devices before I added the service pack.
Maybe ill just get a different sound card.
Who knows.
But at any rate IRQ 5 is reserved for sound cards from what I read online. Unless you have a SB series they like irq's 7 or 9....
Anyways ill let everyone know what I did then.
r00t 3:16

My game center won't load and shows up blank when I try to open it. I've already tried to close all the apps and restart it and it still won't work. Is their anyway to fix it without restoring it??

My game center won't load and shows up blank when I try to open it. I've already closed all of my apps and restarted it and it still won't work. Is their anyway to fix it without restoring it and starting over??

Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- sign out and the sign back into Game Center
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: Back up and restore your iOS device with iCloud or iTunes
- Restore to factory settings/new iOS device.

I just updated my Iphone 3G and now it won´t work anymore. It wouldn´t even boot. It was just working for 3 sek. after the installation and now it shut itself down. Any help, please?

I just updated my Iphone 3G and now it won´t work anymore. It wouldn´t even boot. It was just working for 3 sek. after the installation and now it shut itself down. Any help, please? Thankyou

I suspect you have a 2G iPod. Those can only go to iOS 4.2.1.
Identifying iPod models
iPod touch (3rd generation)
iPod touch (3rd generation) features a 3.5-inch (diagonal) widescreen multi-touch display and 32 GB or 64 GB flash drive. You can browse the web with Safari and watch YouTube videos with Wi-Fi. You can also search, preview, and buy songs from the iTunes Wi-Fi Music Store on iPod touch.
The iPod touch (3rd generation) can be distinguished from iPod touch (2nd generation) by looking at the back of the device. In the text below the engraving, look for the model number. iPod touch (2nd generation) is model A1288, and iPod touch (3rd generation) is model A1318.
You also said: "It also will not let me download any music onto it." What happens when you try to sync music to the iPod?

Loss of sound and video playback on ENVY X2

Every so often, more often than I would like, my HP Envy X2 loses sound and video playback capabilities; any ideas anybody? The concept of this machine is great and have had it for the past 9 months but this loss of sound and vision is so unpredictable and frustating...

Hi Brumage,
I saw your post regarding the sound and video issues and I will be happy to help. Do you get any error messages when this happens? Have noticed if it is a particular site like YouTube or program that you are using when the issue occurs or does it occur on all programs? When you restarted the Envy X2 does the issue go away?
I would start by suggesting that you make sure all updates have been installed through HP Support Assistant and Windows Update.
What operating system are you running? What is your product number?
Find your product number on a notebook:
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&dlc=en&docname=c00033108
Finding your OS:
http://windows.microsoft.com/en-CA/windows/which-operating-system
Thank you,
Please click “Accept as Solution ” if you feel my post solved your issue.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Thank you,
BHK6
I work on behalf of HP

My MacBook and my Monitor won't work together anymore

Ok i have a macbook i got less than a year ago and for the last 2 months i have been running my old samsung monitor off of a mac mini port to VGA and now it won't work anymore when ever i connect it the monitors light just flashes on and off repeatedly but the screen turns black i have tried adjusting the sizing but it wont work...
I know its connected cause the screen blinks blue and the windows that are set to open on it still do and i have to drag them over to see them

Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: Back up and restore your iOS device with iCloud or iTunes
- Restore to factory settings/new iOS device.
If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar
Unless you purchased the optional AppleCare+ extended warranty,
Apple will exchange your iPod for a refurbished one for $99 for 16 GB 5G and $149 for the other 4Gs. They do not fix yours.
Apple - iPod Repair price

[Python pygame] Graphic equalizer - keeping sound and video in sync

Hi!
I'm writing a graphic equalizer in python and I want to use pygame for the video and audio output.
The video display of the moving bars works great, now that I have a correct way to read samples and decode them.
The problem now is: they're way out of sync with the audio playing in the background!
At the moment my code, that draws the bars basically looks like this:
# loop as long as we can get slice of the audio file for the fft
for n_frame in range(0, len(framebuffer), fftframesz):
clock.tick_busy_loop(t_loop)
# t_loop was defined as fftframesz over total_frame_count
# which means in words: t_loop is the amount of FFTs per second - or the cycles of THIS loop
# grab the frames and perform the fft here
...numpy.fft.fft...
# set the new bar heights and draw them
for bar in bars:
bar.update()
# if playback has not started yet, make it so
if not pygame.mixer.get_busy():
musicfile.play()
The way I'm thinking, this should be enough to keep sound and video in sync. Because we know the time that one cycle should take at most,
we can set the clock to tick_busy_loop this time. This way we make sure that the video is not faster than the sound.
But to me it seems that is is the other way round, i.e. that the video is slower than the sound. I already did some timing, but to no avail.
Is there perhaps a more easy, more elegant way to make sure that image and audio are in sync?
Any help is greatly appreciated!
Last edited by n0stradamus (2012-10-01 18:36:53)

Thanks for your ideas. I assume you mean I should go with a $1200.00 final cut pro software. NOT.
Sure the video will be on myspace and youtube but wether they are noticed or not is not as important as self satisfaction. I can easily split scenes into equal time zones as I said. Then drag them into clips and back all using the same camcorder. Multiple cameras and angles would be nice but this can be done on a low budget and still look good. I guess my original questions were not answered. Is there a way to determine the length of a transition and shorten the clip by that amount. Or the length of a still shot and do the same. Or perhaps they have been answered and the answer is NO WAY, and I am just not hearing it.
I suppose reimporting a video would be great if I could use two timelines like in audio and then blank out what I don't want in the first. But I just don't think this is possible, or is it. I've been reading iMovie HD6 The Manual that should have been in the box. It's a help but doesn't take you from the beginning of a project to the final project. Exporting to imovie or idvd is not an issue. BTW I got the clips in sync as I said by leaving blank spots and placing effects over them. I could insert the proper length video in those spots but that can look silly without transitions. But then again so can transitions. This stuff is very fun and interesting and a great learning experience. If I stop now as you suggest then I am not pushing myself to the limit. But thanks for your reply.

Sound and video are choppy since installing Flash Player 11.3

I'm having a problem here! Since I updated Adobe Flash Player 11.3, the audio and video are all choppy when I play Adobe Flash game apps in Facebook! Even when I disabled hardware acceleration, the sound and video are STILL choppy! Even I watch a YouTube video and the sound and video are a bit choppy! There's DEFINITELY some sound issues in Flash Player 11.3! I'm using Firefox 13 in Windows XP SP3. I'm wondering if you have any answers for the sound issues in FP 11.3.

I went through an annoying password reset process to post on here, haha, I was experiencing this issue and managed to resolve it for a flash animation I was making that was going to be sent out; thus fixing it for myself wouldn't change things for others. I know this is old, but if anyone is in this position, I hope it helps.
I was using Swish Max for my scenario.
Under the Export Settings, I found that by default it was using SWF Version: SWF8 - when it had the option to go up to SWF10. I changed it to 10, and set the hardware acceleration to Level 1 - Direct.
I exported, and it still didn't work. The music was choppy as heck and terribly inconsistent with speed. I even created a preloader, which appeared to work but didn't resolve my issue.
FINALLY, I kept it at version 10, and found that it had an option that said "Preload Content: Disabled." I set that to "At Preload Frame" and though I had a loading animation setup to do the preloading, I still placed a preloadcontent keyframe at frame 1. Then I set Hardware acceleration to Level 2-GPU and exported.
IT WORKED. The terrible, seemingly non-fixable audio cracking lag was gone and it worked flawlessly.
Hope this helps someone, I originally found this when I was trying to find a fix for the issue.

Equium-A100-147 - broken sound and video

Hi everyone,
I have the Equium A100-147, Its been working fine for last couple of year.
But in the last few weeks has get problem in sound and video (broken sound and video).
The sound is breaking and sometimes uable to listen + video breaking and so much delay due to its get so slow with so much sound distorsion etc..
This remains after new installation (format HDD) of Wind XP unable to fix even installed new drivers.
The Device Manager shows all drivers including audio and video working ok, d'nt know what's problem please help me.
Thanks.

Hi
Something like that can happen during high HDD activity this means that the reading/writing process could affect the sound/video playback
But usually this should not take long time
At the other hand this can happen because of higher temperature
High temperature can affect the CPU and GPU performance
I think you have used this notebook for couple of month without any troubles in my opinion you should check if cooling modules and fans are clogged and could remove the dust and debris from cooling modules use compressed air spray this helps p get rid of dust
Maybe then the notebook will run much better

URGENT- DOING MEMORIAL VIDEO sound and video are off when sent to iDVD

I watch the video in iMovie and the sound and video are in sync. When I send to iDVD, the two are no longer in sync. I have made changes to the iMovie project since my last DVD burn. With the initial burn, there were no sound issues.
I've tried all of the following:
1. closing and reopening iMovie and iDVD
2. resending from iMovie to iDVD
3. readding the clip and removing the original clip from the iMovie project
4. restarting my computer
The only things I have not done are the following:
1. redownloading the original video clip from my camcorder
2. recreating the project
3. trying a different project to see if that one has the same audio/video issue (this will be my next step)
#2 above is literally so intense as I have a lot of editing on this. To make it clear to you, I have video footage of a memorial.... and after the memorial I chose little 20-30 second clips here and there. I don't have audio with those clips -- just iTunes music overlay.... so, those I don't need to worry about sound coinciding.... just the 30 minute clip that is the actual memorial service.
This is time sensitive.... it is a memorial video and I don't have time to redo the thing from the beginning, especially considering how long it took me to find those 20-30 second clips of the post-memorial.
Please help!

Yes... I had seen that.... and, yep, have the latest software.... and even rebooted my machine thinking that maybe it hadn't been restarted since the update (can't remember how long ago the update was).
I did a test run with a mobile size (it takes over an hour when I share with iDVD, which has been annoying with all my attempts to "fixing") file sharing with media browser and still the sound was not matched.
I started another project alltogether in iMovie and it does not have the sound issue when sent to iDVD....
I can copy and paste the more difficult editing I did between the "bad original copy" and my "do-over"... but, it seems to not copy exact length of each clip (it decreased it by a second each clip on the ones I copied over but that is weird since it did copy over the slowed % I had on the original) ..... see the more complex editing I have has the sound silenced and I have music overlay on that....
I have many more to go... and can't copy text directly from one project to another... in fact, there is a lot you can't just copy over.... I have to redo the music, special effects etc. This is not going to be a walk in the park if I can't find a way to make my "bad original copy" work.
Still looking for more suggestions (than to start all over), but will have to start over if I spend too much time making the one I have work.... then it becomes more sensical to just start over. I have quite a bit of time in the original, but if I can copy and paste the clips, that takes a majority of the work out.... but, if any of my copy and pastes somehow "corrupt" the sound sync on the portion that isn't silenced and music overlaid, then, there is a lot of work having to recreate all my edits from scratch.

Speakers have quit working no sound and it says they are working fine

Speakers have quit working no sound and it says they are working fine

Hi,
Try the following.
Download the IDT Audio installer on the link below and save it to your Downloads folder.
http://ftp.hp.com/pub/softpaq/sp55001-55500/sp55036.exe
When done, open windows Control Panel, open Device Manager and open up Sound, Video and Game Controllers. Right click the IDT device and select Uninstall - you should also get a prompt to remove the current driver, tick the box to allow this and then proceed with the uninstall.
When complete, shut down the notebook, unplug the AC Adapter and then remove the battery. Hold down the Power button for 30 seconds. Re-insert the battery and plug in the AC Adapter.
Tap away at the esc key as you start the notebook to launch the Start-up Menu and then select f10 to enter the bios menu. Press f5 to load the defaults ( this is sometimes f9, but the menu at the bottom will show the correct key ), use the arrow keys to select 'Yes' and hit enter. Press f10 to save the setting and again use the arrow keys to select 'Yes' and hit enter.
Let Windows fully load - it will automatically load an audio driver, but just let this complete. Then open your Downloads folder, right click on the IDT installer and select 'Run as Administrator' to start the installation. When this has completed, right click the speaker icon in the Taskbar and select Playback Devices. Left click 'Speakers and Headphones' once to highlight it and then click the Set Default button - check if you now have audio.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

I just downloaded the ios 6 on my iTouch 4th gen, and my email won't work, my wifi won't connect, my iPod is more sluggish, and honestly I'm really frustrated. Is there anything I can do?

I just downloaded the ios 6 on my iTouch 4th gen, and my email won't work, my wifi won't connect, my iPod is more sluggish, and honestly I'm really frustrated. Is there anything I can do?

Try:
- Reset the iPod. Nothing will be lost
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup
- Restore to factory settings/new iPod.
- Make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar
Downgrading the iOS is not supported by Apple.

Sound and video problems?

ok here is the deal, i got all the latest drivers for my system.
i got the
MSI 875P NEO LSR mainboard
p4 3 ghz with HT
with 1024mb ram
160 gb s-ata
geforce fx 5600 XT/256 mb
soundblaster live 5.1 sound
when i play heavy games like HALO or Need for speed my sounds and video works not correct BUT it should not be a problem because my amd 1800+ with gforce ti 4200 did better
i think it's the mainboard but does ANYONE has an solution or the same problem?
o yeah my system reboots sometimes when i put new hardware on it (had it with my USB modem 4 ADSL)

This sounds like it is your PSU giving troubles. What wattage is your PSU, and what are the 3.3v, 5v and 12v ratings on the PSU? (You can find out this info on the sticker that is attached to the PSU)

Sound and video accelleration won't work on OS 9.2.2

Similar Messages

Maybe you are looking for