Sound Blaster Audigy 2 ZS and Logitech 5.1 Surround So

Hello everyone, this is my first post on these forums, so I thought I'd just start out by saying hello.
I also have a bit of a problem. For the past several months I've had a Sound Blaster Audigy 2 ZS and a set of Logitech X-530 5. Surround Sound speakers hooked up to my computer. For a these past few months, only two of my speakers have been functionable.
I know they're not broken, because I can plug in separate cables into a certain plug and either my two front speakers will work, my two rear speakers will work, or my center speaker will work. And yes I do have the most recent drivers for my card. :P
If anyone would be able to help me with this problem, I would really appreciate it. Thanks!
By the way, here's a picture of the X-530 Speakers I'm using, just in case anybody needs to see them for reference:
http://img53.imageshack.us/img53/2758/b0002wpscg0ss500sclzzzsr.jpgMessage Edited by Triko on 02-26-200706:20 PM

Turn on CMSS if you have not done so.
Jason

Similar Messages

Sound Blaster Audigy 2 ZS with Logitech Z680 Speakers. HELP

Okay, I recently purchased the Logitech Z680 5. set w/ the Audigy 2 ZS sound card (not platinum pro version). Im really happy with it, but doing some research on other forums has given me a LOT of questions and confusion. Here is what I need to know:
To begin with, this section under "support" located at the logitech page (link below)
http://logitech-en-amr.custhelp.com/...fAaVouh&p_lva=& p_sp=cF9zcmNoPTEmcF9zb3J0X2J5PSZwX2dyaWRzb3J0PSZwX 3Jvd9jbnQ9MjYmcF9wcm9kX2x2bDE9JnBfcHJvZF9sdmwyPSZw X3BhZ2U9MSZwX3NlYXJjaF90ZXh0PVotNjgw&p_li=
says that to get TRUE 5. sound with my soundcard and speakers I need to have a digital audio cable that goes from the back of my DVD ROM into the soundcard (like the old ones you put in the back of your CD rom to your mother board to get cd audio). NONE of the local computer stores in the area carry this cable and ALL say I shouldnt need it. WHY do I need it, and where can I find it assuming I do?
Secondly, it says I need a digital connection to get TRUE 5. sound, not analog. So if I connect a coax from my speakers to the soundcard (using an RCA adapter since it wont fit into the back of the sound card) im getting better 5. for gaming and movies than I will with analog?
I really just want to take FULL advantage of these two products to give me awesome 5. sound in gaming. This is all I know so far in doing so, PLEASE critique any errors:
- I had to disable the digital decoder of the Audigy 2 to allow my speakers to decode. I also had to disable decoders built into media software
- I had to configure both windows and my sound card (and my games/dvd software) to play 5. sound.
-I had to hookup a digital audio connector from my DVD Rom to my soundcard
- I had to connect a digital coax from my 680z's to my sound card (along with a mini jack for the coax to fit into the soundcard).
- I had to select "Digital Output Only" and "Synchronize with control panel" under the speaker settings.
Assuming ALL this is done, is this everything I can do to take full advantage of the 5. sound this setup can give me, and will digital REALLY give me the 5. sound over the analog, and is there ANYTHING else I need to consider.
Thank you for your help:-John

Boltboy
I've just posted a similar question today. I spent hours trawling the web looking at AC3 and everything associated with it yesterday - still not 00% on it though. I'm with you entirely in the game department except my external decoder only has a digital coax input (the optical is for my Xbox) - I don't have the choice of digi vs analogue as you seem to have.
The only thing I'm not sure if you're aware of is that the set-up you describe doesn't give you Dolby Digital as there is no on-board DD (AC3) encoder. You'll only get DD 5. from AC3 encoded sources like DVDs - you can either set the digital output to passthrough and decode externally or you can decode internally on the Audigy and use the analogues. Not sure which of your decoders is highest quality. I think the 5. you're hearing for games is generated by the Creative hard/software and you'll never get "true" 5. if "true" means Dolby Digital. Having said that, who cares whether it's DD or not if the gunshots sound like they are coming from behind you and you're getting a decent experience ?!
Maybe you can help me in that respect - f you have set up your system as below (Aud 2 ZS to mini-jack/coax and in to your digi coax input on your external decoder), how did it sound? Did you get all 6 channels during the tests? If you think it sounded good for games then I'm off out to get an Audigy 2 ZS and get going because unless I can find a sound card with AC3 encoder (which I can't), then that's my only option. PLEASE let me know if it sounded good to you.
Cheers
Robbo

Creative Sound blaster X-Fi Titanium and Logitech z-5500 5.1 speakers

Hi All:
I have had the Creative Soundblaster X-Fi Titanium and Logitech z-5500 connected to my HTPC system for some time now. I have the two connected with analog cables and an optical cable. Unfortunately, I have never been able to set the optical connection working. The only mode the speakers will work in is analog.
Does anyone have any ideas/suggestions regarding this?
Thanks,
Harold

I have the same card and the same speaker.
You need to enable DTS or DDL encoder in the Creative Control Panel.
Otherwise you can play only native digital track like DTS or DDL from DVDs or BDs (in this case you MUST select Digital output device as the default device in the windows audio control panel)..

Sound blaster audigy 2 ZS and the rege

hello .i was going to do a uninstall and reinstall of my audigy 2 ZS.i would like to know what files in the regedit to delete.which ones are for the card.i am hoping to do a clean install of my card.any help would be cool.thanks

frankr,
The thread below doesn't list the creative entries to delete from the registry (that would vary by card), but it might get you started.
http://forums.creative.com/creativelabs/board/message?board.id=soundblaster&message.id=46974

What's the diff. between Sound Blaster Audigy MB Audio and the similar but ADVANCED ca

I just bought a Dell Inspiron 53 with?the?former card, but whenever I search for more info about it, I can only find the "Advanced" version. Please, can you tell me, what's the difference between the two cards?Also,? as I was building the PC, Dell offered only two other?audio options, and this was the middle one; none of the other choices was ideal. This appears to be a bottom-of-the-barrel card, so can anyone recommend?a replacement?card for under $40-$00 that wouldproduce very high quality music for my new 5. wireless Dell speakers?Much obliged.

I've been fiddling around in the Device Manager and it has Other Devices and under it is Multimedia Audio Controller, I can choose to either reinstall the driver udate the driver, disable it, or uninstall it. Here's what comes up on properties
This device is not configured correctly. (Code )
To reinstall the drivers for this device, click Reinstall Driver.
Help would be appreciated here. I'm a big gamer and would like to have this up and running before our first CAL Match.

Creative Sound Blaster Audigy ZS And Vista Driver installation prob

HI!
I encounter Installation problems with that file:
Creative Sound Blaster Audigy Value/SE/LS and Sound Blaster Li've! 24-bit XP and Windows Vista Pack .04.0077
I Use Vista 64Bit Ultimate and when I try to install this package I have an error message after my language selection. Is there a known issue for this
Thanks!
Julien

estebandit wrote:
Is there a known issue for this
Yes it is called trying to install the wrong driver for your card. Will work much better if you try installing the correct one,
SBAX_PCDRV_LB_2_8_000.exe
Also helps if you click on the "Show Details" link on the download page, then you would see that the one you tried to install doesn't support your card,
Requirements:
Microsoft Windows Vista 64-bit, Windows Vista 32-bit, Windows XP Professional x64 Edition, Windows XP Service Pack 2, Windows XP Media Center Edition 2005 or Windows XP Media Center Edition 2004
Sound Blaster Audigy Value/SE/LS, or Sound Blaster Li've! 24-bit audio devices
whereas the correct driver shows the following,
This download supports the following audio devices only:
Creative Sound Blaster Audigy including Platinum and Platinum eX series
Creative Sound Blaster Audigy 2 including Platinum, Platinum eX, and Value series
Creative Sound Blaster Audigy 2 ZS including Platinum and Platinum Pro series
Creative Sound Blaster Audigy 4 Pro and Sound Blaster Audigy 4
Creative Sound Blaster Audigy 2 ZS Notebook PCMCIA

SOUND BLASTER AUDIGY SE AND VISTA DRIVERS WITH FULL FUNCTIONALITY- WOOOOO

(ONLY DRAWBACK IS THAT YOULL HAVE TO FIND ANOTHER MEDIA PLAYER BESIDES WINDOWS MEDIA PLAYER FOR YOUR SAVED AUDIO FILES: I WENT WITH WINAMP)
CONTINUE ON-
Download RAR file with ISO inside and install if you don't have the installation CD
installation cd with EQ download: http://files.filefront.com//;689430;;/
If you do or after you finish downloading goto step A.
A) Take your Creative Driver/Install CD, copy it to your hard dri've.
B) Goto Setup.exe right click, goto properties, goto the Compatibility tab.
C) Set it for Windows XP SP2.
D) Run install the Creative Audigy and if you need MediaSource *WMP Will pop and hiss while multitasking I reccomend MediaSource as it does not although the "Sources" is glitchy.
E) Restart when told to
F) Part ) Right click on the speaker icon by the clock, click Audio Devices... Right Click on Playback Control, goto properties click Configuration Set it to Stereo hit apply.
F) Part 2) Goto Speaker Settings, Set the configuration to 5./7. depending on what you need, then make sure Sync with Control Panel is UNCHECKED I found that is the critical element! Enjoy your multichannel!
G) Part ) Right click on the speaker icon by the clock, click Audio Devices... Right Click on Playback Control, goto properties click Configuration Set it to Stereo hit apply.
G) Part 2) Goto Speaker Settings, Set the configuration to 5./7. depending on what you need, then make sure Sync with Control Panel is UNCHECKED I found that is the critical element! Enjoy your multichannel!Message Edited by jeepbme on 03-08-200708:49 PM
Message Edited by jeepbme on 03-08-200708:50 PM

estebandit wrote:
Is there a known issue for this
Yes it is called trying to install the wrong driver for your card. Will work much better if you try installing the correct one,
SBAX_PCDRV_LB_2_8_000.exe
Also helps if you click on the "Show Details" link on the download page, then you would see that the one you tried to install doesn't support your card,
Requirements:
Microsoft Windows Vista 64-bit, Windows Vista 32-bit, Windows XP Professional x64 Edition, Windows XP Service Pack 2, Windows XP Media Center Edition 2005 or Windows XP Media Center Edition 2004
Sound Blaster Audigy Value/SE/LS, or Sound Blaster Li've! 24-bit audio devices
whereas the correct driver shows the following,
This download supports the following audio devices only:
Creative Sound Blaster Audigy including Platinum and Platinum eX series
Creative Sound Blaster Audigy 2 including Platinum, Platinum eX, and Value series
Creative Sound Blaster Audigy 2 ZS including Platinum and Platinum Pro series
Creative Sound Blaster Audigy 4 Pro and Sound Blaster Audigy 4
Creative Sound Blaster Audigy 2 ZS Notebook PCMCIA

Sound Blaster Audigy

Hello,
I have brought this Sound Blaster Audigy sometime ago and it makes a screaming horrible noise when i try and talk on ventrilo.
I have uninstalled multiple times, installed drivers, iv done everything i can possibly think of. the current driver is 5.2..608 and it says the Driver date is 20/03/2006.
I took some screenshots of the setup.
[IMG"]http://i20.photobucket.com/albums/b23/CallumPirie/untitled2-.jpg[/IMG]
[IMG"]http://i20.photobucket.com/albums/b23/CallumPirie/untitled-3.jpg[/IMG]
any help would be great?

After you reformatted your hard dri've did you install the chipset driver? What OC, XP, Vista?
Dell XPS 600 Intel Pent D 830 3.0ghz
Chipset- Nvidia nForce4 SLI Intel Edition
WD 60gb HD
2gb Ram
DVD-ROM
DVD-RW (Plextor 760A)
Creative XF-I Extreme Music
Logitech X-540 speakers
EVGA 7950GT
Dell 2007WFP (I-SPS panel)
Win XP SP2
BIOS A

Sound blaster audigy 4 car

i have a sound blaster audigy 4 card and have lost the manual. could you please tell me what color plug is the correct one for headphones

Hi,
Go to the Support section of the website and select your product. You should see Quickstart User Guide next to the Audigy 4 picture in the center. Click on the Quickstart User Guide, it should bring you to the manual download.

Sound Blaster Audigy 2 ZS Internal Drive (Upgrade Opti

I own a Sound Blaster Audigy 2 ZS, and in the instruction manual and on your website you mention a Internal Dri've Upgrade Option like the one that comes with the Sound Blaster Audigy 2 Platinum. My question is i have found similar products available for the Sound Blaster Li've series, but i have not found that product available as an upgrade for the audigy 2 zs. Could you tell me if it is not in production or if the li've di've IR is compatible with the audigy 2 zs. Also the manual noted a adapter needed for the spdif out, were is that available?

Anoddin,
The Audigy 2 ZS dri've is here:
http://us.creative.com/products/prod...=6&product=024
Jeremy

Sound blaster Audigy 2 ZS bad so

Hi.
I have a Creative Sound Blaster Audigy 2 ZS and I just installed Windows Vista yesterday. The auto updates for Vista gave me some working drivers for my sound card, but sometimes the quality just sounds way worse than it did with Windows XP. Has anyone else noticed this? Is there a way to fix it's
James

First unistall Creative stuff through add remove programs.
Next run Guru3D driver sweeper and double check the log for failed removals.
Next uninstall Creative hardware in Windows device manager. (also tick "delete the driver software for this device")
After that, you should have deleted everything!
As for "the best drivers", both are (the same but) different and it depends on what you want to use your card for. Both work fine wth ALchemy and both get the job done.
daniel_k's latest drivers have equalizer, louder volume and advanced CMSS. daniel_K also has a few hybrid ISO with DVD audio, MIDI and other valuable applications. They don't always perform as they should though for obvious reasons (NO OFFICIAL CREATIVE VISTA SUPPORT - XP applications - No Hardware Audio).
nomoregoatsoup are just recent X-Fi drivers and a basic Creative Audio console. They offer improved sound quality over the official version and also offer limited DTS/SPDIF options like the Dell counterparts.
All current Audigy Vista drivers are inferior compared to XP ones.

Creative Sound blaster Audigy 2 ZS is

My sound was working perfect until recently. I'll be listening to windows media player,internet music,playing games when suddenly the sound gets quieter for up to a few seconds to a few?minutes then returns to normal. I?Tried updating driver and it still does it.
Specs
Sound Blaster Audigy 2 ZS
Dell 5650 5. Surround Sound Speakers with Subwoofer
Dell Dimension XPS Gen 4<span class="sign"><span class="gensmall">

My sound was working perfect until recently. I'll be listening to windows media player,internet music,playing games when suddenly the sound gets quieter for up to a few seconds to a few?minutes then returns to normal. I?Tried updating driver and it still does it.
Specs
Sound Blaster Audigy 2 ZS
Dell 5650 5. Surround Sound Speakers with Subwoofer
Dell Dimension XPS Gen 4<span class="sign"><span class="gensmall">

Sound blaster Audigy 2zs platinum setup with creative inspire 5.1 digital 5

what should the setup be for the sound blaster Audigy 2zs platinum and the reati've inspire 5. digital 5500 because with the decoder in i only get center fl fr on games. i dont get sound from the rear speakers.but when i take the decoder out and just plug the 3 leads straight into the back of my sound card i get 5. any help plz.i done a thx sound test with the decoder in it does fl i can hear it but i can hear the center as well
and no sound comes out on the 2 rear speakers when doing the test.but when puting the 3 cables straight into the back of the sound card i runed the test and i could hear all the speakers fine even the rear speakers any help plz is this ment 2 happen or do i have to change some settings thanks for any help plz help me thanks.

I Have had a problem for ages. I have the Audigy 2 ZS Platinum and Inspire 5. digital 5500.
I have copied the advice I received/didnt recieve from creative.
Best of luck
Dear Martin
Thanks for your reply
I am sorry for the problem you are facing.
To achieve outputs from all the speaker during speaker test, you will need to have an analog connection, or digital DIN connection.
That will be possible if you connect the three line out jacks on your soundcard, to the three audio input (analog jacks->green,black,orange) on your speaker, if it has this connection. Or, you may connect them using Digital DIN, if they have this connection.
If you are using digital connection (coaxial, optical), there will be no way to achieve sound output from all the speakers during 5. speaker test, as they carry stereo signal.
Best Regards
(Mod Note: Name Removed)
Creative Customer Support Services
Creative Labs Europe:
Original Message Follows:
Hi
I understand you must be busy, so no problem.
No I do not hear EAX when in Pro-logic mode. I only hear (depending on the game in question)
Half life two: front left-right and centre. NO rears
Fear: Front, left, right, & centre. No rears
Farcry Front left, right & centre. No Rears
When I run your speaker test HISSSSS, No Rears, no front left or right
Beats me?
Regards
Martin
-----Original Message-----
From: CLE Customer Support [[email][email protected]]mailto:[email protected][/url]]
Sent: 24 January 2006 5:44
To: Martin
Dear Martin
I apologize for the delay on the answer.
If you select Dolby Prologic mode on the decoder, are you able to listen
the game audio, with EAX, in all of the speakers?
Regarding to the optional bay dri've, you can purchase it from ou
Best Regards
(Mod Note: Name Removed)
Original Message Follows:
Hello
Your email was helpful, unfortunately, not for my unit, you see I would
have
connected the Jack leads in by now if the inspire had Jack lead inputs
as
you describe
Please don't think I am being sarcastic, but from reading the
correspondence
below it would seem as if your department is having difficulty
understanding
my problem.
Also it would seem your department doesn't have the necessary technical
information on your very own product, so to help with your dilemma I
have
taken photos of the input/outputs on the Inspire unit.
You will clearly see the inspire has no inputs other than Coaxial and
Optic.
This leaves me back to my last post. I think the solution would be for
me to
purchase the correct processor, which would have come with the original
sound card had I not been a little tight on the money front.
I have attached a photo of the sound card with the processor, I would
love
to buy this processor but find myself unable to locate this product on
your
web site. Would you possibly be able to send me the correct link to this
item so I can buy this Processor Please?
Kind regards
Martin
-----Original Message-----
From: CLE Customer Support [[email][email protected]]mailto:[email protected][/url]]
Sent: 8 January 2006 0:3
To: Martin
Subject: RE: CLE -
Dear Martin
Thanks for your reply
Your soundcard is Audigy 2 ZS
Your speaker is Creative Inspire 5. Digital 5500
You will need to have a 3:3 cable(with the color green, black, orange)
to connect your soundcard to your speaker, to achieve the 5. effects
with games.
Below is the connection:
- Connect line out jack of Audigy 2 ZS
to 'Front' of Creative Inspire 5. Digital 5500 using the green color
connection
- Connect line out 2 jack of Audigy 2 ZS
to 'Rear' of Creative Inspire 5. Digital 5500 using the black color
connection
- Connect line out 3 jack of Audigy 2 ZS
to 'Center/Subwoofer' of Creative Inspire 5. Digital 5500 using the
orange color connection
Once you have done the correct connection, play the game DOOM3.
Ensure you have selected either the EAX or surround option in the game
settings.
Does it work?
Best Regards
(Mod Note: Name Removed)
Creative Customer Support Services
Creative Labs Europe
Original Message Follows:
You have lost me. Your sound card clearly states that I can have EAX
surround decoding from the sound card I have purchased.
All of the games on your web site claim to give me an environmental
effect
that will blow my mind, hence EAX.
All I have done wrong is NOT buying your decoder that comes with the
sound
card. My mistake.
All I want to do is re-address this issue and buy the correct
decoder/processor.
Can you point me to the correct link on your web site so I can buy the
correct decoder/processor?
As for the PCM out of the above cables, this foxes me as my other
equipment
only use Optical cabling on my Lexicon processor and from that I have DD
7., DTS 7. and meridian 5. lossless.
My issue is more to do with NO EAX from the rear and centre channels
while
in-game.
Kind regards
Martin
-----Original Message-----
From: CLE Customer Support [[email][email protected]]mailto:[email protected][/url]]
Sent: 6 January 2006 09:3
To: Martin
Subject: RE: CLE - Technical Support Request (KMM887805I6636L0KM)
Dear Martin
Thanks for your reply
All commercial digital connection eg. optical or coaxial cable will only
carry PCM stereo signal. If you want to output the signal to a surround
5. with extra EAX environment effects, it will not be possible at all
since it is only restricted to stereo channel signal.
As per current industry limitations, we are bound to follow the standard
one-signal output for all our SPDIF and Optical output jacks. This is
something that is currently shared by all vendors for all products.
Please note that all games are not dolby digital, even they are , it
will require certain motherboard to encode it to dolby digital signal,
which our soundcard does not support.
You can only use analog connections to gain true 5. surround for
gaming..
email.
Best Regards
(Mod Note: Name Removed)
Creative Customer Support Services
Creative Labs Europe
Original Message Follows:
Hi Joong
I don't fully understand your email, but I do get the gist of what
you're
saying and understand I need to connect the analogue cable to fully
appreciate the sound in EAX.
Would you be able to tell me what product I could buy from your
catalogue
which would marry up with the sound card I have, as I understand now
that
the Inspire 5. will not do the job.
Kind regards
Martin
-----Original Message-----
From: CLE Customer Support [[email][email protected]]mailto:[email protected][/url]]
Sent: 6 January 2006 04:00
To: Martin
Subject: RE: CLE - Technical Support Request (KMM8875697I6636L0KM)
Dear Martin
Thank you for the reply.
Computer games written with support for 3D audio do not require a Dolby
Digital Interacti've Content Encoder (DICE) to output multichannel sound,
with no exceptions. Sound devices that support the real time encoder
technology from Dolby will simply receive the multichannel wave file
output and encode it in real time to a somewhat modified Dolby Digital
bitstream. Creative does not support the Dolby Digital Interacti've
Content Encoder on any of its sound cards.
The only difference between a Sound Blaster card and an audio card that
has a real time encoder, is that you can make a one-wire, digital
connection from your audio card to your home theater receiver and enjoy
discrete multichannel sound from the game. However there will be a
continuous, slight delay, known as "latency", as the encoder is creating
and transmitting the bitstream, and of course the compression scheme
being used is "lossy" (i.e. not bit-accurate).
If you want to enjoy 3D audio in 3D enabled PC games in multichannel
surround sound with a Sound Blaster card, it is recommended that you
connect the analog outputs of the sound card directly to the analog
inputs of the receiver. This will require 3 cables for 5. surround
sound, one for front right and left, one for rear left and right, and
another one for front center and subwoofer. Though it requires more
cables than a real time encoder system, it will not have any latency
issues. When connecting PC audio to a home theater receiver, Creative's
latest sound cards such as Sound Blaster Audigy, Sound Blaster Audigy 2
are likely to provide higher quality audio than any Dolby Digital real
time encode system available for the PC today.
Please retain all the previous correspondence when replying to this
email.
Best Regards
(Mod Note: Name Removed)
Creative Customer Support Services
Please do not use this link to submit technical queries
Original Message Follows:
Hi
One particular game which has "in-game" DD is Farcry; I used this as my
benchmark disc for DD and to push my Nvidia 7800 GTX GPU's (I have tried
it
on friend's machines and they get the full surround effect so I Know
this
version is ok. I also have ALL of the game patches & updates.
I would like to point out that while playing Doom 3, Half Life 2,Fear,
Colin
McRae rally 04,FIFA 2004,Meddle of honour pacific assault, Rome, Shadow
ops, All these games have EAX HD, which is enabled within the options
menu
"in-game", But I do not get ANY use out of the rear's and I might as
well
listen in stereo.
No, inspire 5500 does not automatically switch while "in-game" when DD
is present as you would expect, but does if it was a Movie, which makes
me
think the DD stream isn't getting to the processor.
I originally thought I could put all this to rest if I could buy the
control
panel that would have come with the Sound card if I had not tried to
save
money, but every time I search your accessories site I get completely
lost,
it really isn't user friendly, the sub-menus are very time consuming and
point you in the wrong direction because they are not categorised as Joe
public would understand
I downloaded your TEST Movies and creative demo player utility, ran it
but
still no EAX HD or DD if that were present.
I want to put this card and Processor into my boys computer (which is
the
same Spec as mine and I will update to the FX series, but I am unwilling
if
I cannot find a logical reason why this set-up cannot work first.
Would it have anything to do with the pins on the Digital out on the
sound
card plug, the one I bought and was attached to the last email? Only
sending
certain channels down to the processor?
Regards
Martin
-----Original Message-----
From: CLE Customer Support [[email][email protected]]mailto:[email protected][/url]]
Sent: 5 January 2006 08:09
To: Martin
Subject: RE: CLE - Technical Support Request (KMM8868993I6636L0KM)
Dear Martin
Thanks for your reply
Your speakers are fine as you mentioned that there is sound from all the
speakers when you are playing movie.
May i know what game are you playing when there are no sound from the
rear speakers?
Have you done the appropriate settings in the game to achieve the 5.
sound?
Is there any game patches that you will need to update?
Does the Dolby Digital LED light up when you are playing the game?
Please retain all the previous correspondence when replying to this
email.
Best Regards
(Mod Note: Name Removed)
Creative Customer Support Servic
Original Message Follows:
Hi
I am sorry; I should have said the Inspire 5. was model number digital
5500
S/N SW330030026.
The inspire has these connection on the back of the processor
>From top/back of unit
Audio Outputs
Front
Rear
Centre/subwoofer
Audio inputs
Audio line in
Coaxial
Optical
DIN
The Din to a remotely located Subwoofer which has the speaker leads
inputting into it. Plus power.
Attached is the creative view of the controls menu and I have attached
the
invoice I was sent, it shows the lead I was told to fit.
As I said, I can now hear DD5. while within a movie from ALL speakers
BUT
no sound from rears during IN GAME DD5.
I do not use this PC for films only games.
Regards
Martin
If you are having a digital connection, it is normal for only get only
front left/right is you use the speaker test option.
http://us.creative.com/support/kb/article.asp?l=3&sid=4858
Speaker test only outputs from two front speakers?
You mentioned that that you are unable to get any sound from the rear
speakers when playing game right? May i know are you using a digital
connection? May i know what speaker settings have been made under
Creative Speaker settings?
Do get back to me on the above.
Thanks
Original Message Follows:
Operating System: Windows XP Professional x64 Edition
Creative Model Number: SBO 350
Computer Brand/Model: home made
Processor/CPU: AMD 64
Memory: Gig DDR 4
BIOS Type/Revision: 5. 39
System Board/Chipset: ASUS A8N-SLI Deluxe
Detailed Problem Description:
I have the above Sound card.
I also own Inspire 5. amp/processor
I Wanted to save money by connecting above sound
card to amp/processor
Connections on sound card made life very difficult
I contacted Creative for help. you told me to buy
an RCA to mini jack cord which also has other connections, from your
web site, (I tried to find
the product number for you, but your sub-menu
system is so poor I couldn't locate the RCA/mini
3.5 /to phono link for you) this cord connects
directly into the digital in, on the sound card (3.5 Mini jack) to the
coaxial input on the
inspire 5. amp/processor.
I have enabled ALL sp-diff settings and digital in
setting on every program/utility/kitchen sink and all.
I have an SP-Diff wire from DVD burner to creative
sound card, and yes its enabled and digital only
is selected.
I can play a DVD and see the inspire 5.
automatically change from Pro-logic to Dolby
digital when it See's an AC-3 stream.
when I try and play ANY game you say has EAX
,2,3,4 I cannot get any sound from my rear
speakers (see above in Dolby Digital ALL speakers
work correctly)
when I enter the set-up menu within the creative
software you supply with the sound card and select
5. speaker, digital only, test the speakers via
the white noise function, all i hear is left and
right noise. no centre, no rears.
I phoned you tech support line, the boy on the
phone didn't have much of a clue about your
product and I had to tell him what connections sit
on the inspire 5. series amp/processor.
I want to build another PC for my son, I want to
add the FX series sound card and amp, but i am not
willing to buy anything until i feel you have
helped me to solve this problem first.
please can you help, I am at the end of my tether
with this sound card.
kind regards
Martin Waite
Message Edited by Daniel-CL on 0-28-2006 :36 PM

"Sound Blaster Audigy Fx" and stereo mix availability

If I buy/install the "Sound Blaster Audigy Fx" will it add the stereo mix option to my sound properties, also
does this card work on windows 8?
http://www.bestbuy.com/site/creative...&skuId=3287009

Re: Sound Blaster Xtreme Audio missing Stereo MixK I think I'm having a similar problem with my Windows 7 Professional system.
I'm am getting sound out of my card.
When I right click on the "speaker" icon in the task bar I see the following list of 5 options
Volume Mixer
Playback Devices
Recording Devices
Sounds
Volume Control Options
However when I click on "playback devices", "Recording Devices" and "sounds" nothing comes up.
What I did do is completely uninstall all traces of any installed Creative software and in the device manager did an uninstall for the SB Xtreme Audio Card.
My recording device is the integrated microphone in the Logitech Quickcam/IM that I have installed. If I go to accessories and click on "sound recorder" it doesn't start up either.
The other issue that I see is that when I go into Control Panel and click on Sounds, nothing happens.
Something is definitely going on but I can't seem to track down the cause.

Sound Blaster Audigy + Logitech G51 problem

Before I replaced the motherboard, graphics card, and processor, I had the SB Audigy [8000] version of the software for my Creative Sound Blaster Audigy sound card. All of the new versions I have downloaded, including the old one, are now [BF00]. Also for some reason, the drivers on the CD install [BF00] as well. Previously it didn't. I have the Logitech G5 surround sound speakers, and when I try to use the Matrix mode in-game, only some speakers will work. When I turn off the matrix, it becomes more surround sound, but I still do not hear some things - It shouldn't be doing this when the matrix is not turned on. When the matrix is not turned on, you would only be able to hear from the front left and right speakers only. When not playing a game, the Matrix seems to work fine, however when I don't have it turned on, I still get surround sound. Again, that shouldn't be happening.
The Matrix mode in game seems to not play all of the sounds in-game, and while not in-game, I still get surround sound without the matrix mode on. This shouldn't be happening; I should only be getting the sound from the front left and right speakers when the matrix is not turned on.
Outside of games, when I turn the bass and treble via the sound controls by the time display all the to the max (Not the acutal volume control for the speakers) it sounds garbled. Before this, that wouldn't happen.
Its all worth mentioning that for some reason, my computer does not have the " Audio Device on Definition Audio Bus " driver installed. My computer cannot find the drivers for it though.
With the [8000], when you didn't have the matrix turned on, you would only be able to hear the two speakers in the front. I cannot find the [8000] version online. Does anyone have any idea what the cause of this is?
Any comments are welcome, thank you
Computer specs:
Sound: Creative Sound Blaster Audigy
Speakers: Logitech G5 Surround Sound
Monitor: LG E2350V
Graphics: Asus GTX 460 GB
Motherboard: Gigabyte 870A-UD3
Processor: AMD Phenom II X4 965
OS: Windows XP SP 3

I'm having a similar problem as well i've had my card for a year now and its just this high pitched sound. it doesn't happen right away but it happens after a period of time of using sound of any type music, games....it getting iritating and gives me a headache i think we have a simlar problem i've looked into the drivers and i'm not all to sure what i need none seem to mach my needs? does anyone have any idea's please help!

Sound Blaster Audigy 2 ZS and Logitech 5.1 Surround So

Similar Messages

Maybe you are looking for