Sound blaster zxr mic problem

Hi,
I know this issue has been discussed, but still no solution.
Problem is that when i use mic on skype, my friends says my voice sounds damped and bass rich. It helps if i turn crystalizer off but then it gets static noise from somewhere(like fan humming).
Too pricy card to have this kind of issues unsolved.
Software related?

Can you retry your ZXR microphone with Skype again but with the SBX ProStudio effects turned off? I think your noise cancellation wedge setting in the control panel may be too narrow, so you get the muffled voice sound instead of a light, airy sound.
Originally Posted by Jupe
Hi,
I know this issue has been discussed, but still no solution.
Problem is that when i use mic on skype, my friends says my voice sounds damped and bass rich. It helps if i turn crystalizer off but then it gets static noise from somewhere(like fan humming).
Too pricy card to have this kind of issues unsolved.
Software related?

Similar Messages

Sound Blaster ZxR latency problems

I bought SB ZxR last week and I'm using it for gaming, recording and just rehearsing guitar playing (my preamp is connected to sound card AUX in). I'm having trouble getting the sound in sync with my playing. In fact it's pretty much impossible to play properly, because the sound is always some 20-30ms late. I understand that when I output to optical output, then there might be some delay, but the delay is there also when outputting to analog outputs (though not so bad, but makes playing impossible still). I've tried all the settings in ZxR control panel and I haven't found working combination. Seems like the card is doing some processing to incoming signal in all occasions. I'm really disappointed, since the sound quality is otherwise excellent. I haven't had this kind of problems with my previous sound cards (Terratec 6fire, X-fi Elite pro, Auzentech Prelude). Prelude created latency when enabling DD live or DTS encoding, but disabling those made latency almost zero.
Has anyone tried playing any instrument live with this card and maybe found a solution for these latency problems?

Originally Posted by slumberfi
...(I suspect the hardware simply isn't capable of significantly better performance).
Incorrect in my experience.
I've just installed a Sound Blaster Zx - purchased because it is supposed to have near zip latency.
and it was so - with 92000 sample rate and 192 samples! Latency was near zero.
Before it was near 10-20 milliseconds with my old SB Fx 1270 THX
My keyboard is so fast it's weird getting used to it.
Notes:
1. select the Sound Blaster SBZ series ASIO, NOT the "Creative ASIO".
2. Be sure to remove all old Creative software before installing. I tried it without doing this cleaning, and got odd silences in my browsers at random-seeming times. It seems to work better now.
3. Measuring tool: DPC latency checker V 1.2.0
(CEntrance latency test did not work)
Results: Average latency 26 microseconds,
peak latency 1120 microseconds when starting up Kontackt 5 (note: Micro, not Milli-seconds)
I'll let you know here if I have problems -
Ken Rushton
Background: running Kontact 5 Player.
OS Name Microsoft Windows 7 Home Premium
Version 6.1.7601 Service Pack 1 Build 7601
Other OS Description Not Available
OS Manufacturer Microsoft Corporation
System Name KEN-PC
System Manufacturer System manufacturer
System Model System Product Name
System Type x64-based PC
Processor Intel(R) Core(TM) i7 CPU 950 @ 3.07GHz, 3068 Mhz, 4 Core(s), 8 Logical Processor(s)
BIOS Version/Date American Megatrends Inc. 0803, 8/6/2012
SMBIOS Version 2.5
Windows Directory C:\windows
System Directory C:\windows\system32
Boot Device \Device\HarddiskVolume1
Locale United States
Hardware Abstraction Layer Version = "6.1....
User Name Ken-PC\Ken
Time Zone Pacific Standard Time
Installed Physical Memory (RAM) 12.0 GB
Total Physical Memory 12.0 GB
Available Physical Memory 8.79 GB
Total Virtual Memory 24.0 GB
Available Virtual Memory 20.7 GB
Page File Space 12.0 GB
Page File C:\pagefile.sys

Creative Sound Blaster ZxR Optical s/pDIF Surround Recording

I just downloaded and installed Audacity for Windows version 2.x.x (the latest Audacity version).
I'm recording my xbox 360 game play sound and possibly some OTA Antenna receiver Dolby 5.1 Surround through a Toslink optical cable input on the daughter card of the SB ZxR sound card.
I'm using an Intel Core i7 2600 in an Asus p8p67 deluxe running Windows 7 Ultimate x64 using the Creative Labs Sound Blaster ZxR.
It works fine for Xbox 360 dashboard System Settings, Console, Digital Audio, set to Stereo (2 channel sound), but does not when xb360 is set for Dolby Digital 5.1 output since the Audacity drop down list box for the recording device has only the options for Stereo or Mono--even when 5.1 Surround is being output by the xb360.
When the incoming audio stream of 5.1 surround is recorded by audacity, the sampled sound is a huge amount of loud almost white noise of random digital static sound.
What audio device capabilities enumeration is being used to determine if incoming AC3 multichannel digital optical signals are more than stereo since this stream could, in theory, change on the fly depending on the program material being sent by the source device?
Is this the fault of the sound card driver from Creative Labs and is being reported improperly to MS Windows intermediate level device driver layers, that are in turn reported to audacity in its enumeration of the device's input stream contents?
To see the physical appearance of the Creative Labs Sound Blaster ZxR DBpro daughter card with its gray output Toslink female socket and its black input Toslink socket, do a Google image search as follows:
"sound blaster zxr" optical in dbpro "daughter card"
http://goo.gl/ewO6ha
Is there any way to circumvent this sad state of affairs as a temporary work around for this problem with an interim software source code revision?
Could a software layer or function be added in audacity to parse the incoming data stream to determine the streams' characteristics (possibly on the fly -- in real time)?
When in the Creative Labs SB ZxR software control for mixer, etc, I have the settings for the card sometimes set to "listen to this device" for the Optical Toslink input port, and the sound coming out of the Speaker Outputs does not get sent to the Optical Output Toslink port to go to my Dolby digital audio receiver--my default Windows sound device--so that I cannot hear any of the supposed input audio stream at all.
Why is this effective pass through functionality not working?
I have two or more Hauppauge ComputerWorks High Definition Video capture devices with Toslink optical inputs, and they work fine to capture higher level multichannel AC3 optical streams.
What is wrong with the Creative Labs Soundblaster ZxR recording capability for such streams?
Can the driver be updated to fix these problems?
I have posted a few hours ago on the Audacity software's web forums to see if anyone there has any answers as to what can be done and what is happening and what is at fault in this process...
http://forum.audacityteam.org/viewto...p?f=46&t=84846

I noticed the following when I more closely examined the SB ZxR Mixer settings...
The Toslink / optical s/pDIF input levels, even when an AC3 surround 5.1 channel stream is being input displays level control sliders for only Left and Right channels, when there should be 6 channels.
Creative Labs Dolby is improperly being handled within both their driver and application software for the sound card, or the card itself is designed NOT to handle properly multichannel AC3 in a dynamic fashion as provided by the source optical device.
Why?

Sound Blaster ZXR Creative Audio Control panel

Hi. I bought a soundblaster ZXR. I uninstalled the driver for the old sound blaster X-Fi card, then shut off my computer and installed the ZXR card (which fits into a different slot than the X-Fi did), then restarted the computer and installed the software for the ZXR.
My situation is as follows: when I click on the Creative Audio Control panel, I get a message saying "The audio device supported by this application is not detected". I looked thru the internet and the general advice seems to be that the software for the older X-Fi card is not easily removed, and to remove it, I should uninstall the ZXR software, remove the ZXR card, re-install the old X-Fi card, then use some rather advanced techniques to make sure all of the software for the X-Fi card is uninstalled, then turn off the computer and take out the X-Fi card, then install the ZXR card, and re-install the software for the ZXR card. With some reluctance, I was about to do that, but then I noticed a folder called Sound Blaster Z Series was installed, so I opened it and clicked on Sound Blaster Z Series Control Panel, and a program opened up which allows me to make some changes to my sound set up.
My question is - When I click on the Creative Audio Control panel, am I supposed to get a message saying "The audio device supported by this application is not detected", because the Sound Blaster Z Series Control Panel is taking it's place? ...or does that error message tell me that there's something that I should address to avoid any future problems. I want to learn how to work with various sound programs, like sound forge, cakewalk, acid pro, kontakt, etc. and I want to start with a proper setup to help me avoid any unneeded frustrations. I have a fairly new computer with an ASUS P8H77 motherboard. Under Device Manager - Sound, Video and game controllers, I have the following entries:
High Definition Audio Device
Sound Blaster Audio Controller
Sound Blaster ZxR
Sound Blaster ZxR DBpro
I right clicked the High Definition Audio Device, then disabled it, but that didn't help so I enabled it again.
Thanks.

The Creative Audio Control Panel is a single entry leftover from your old X-FI. Uninstall just that. Then you can make a shortcut to the other you were speaking off and put that shortcut wherever you wish. I uninstalled an X-FI before and I had that control panel left over even after uninstalling what I thought was everything.

Sound Blaster Arena Headphones Problem - On and Off

I have a problem with my Sound Blaster Arena Headset. Its been working perfectly until yesterday. It keeps turning on and off in the playback devices but it stays off unless I replug the USB or switch USB ports. Then shortly after it works again it turns off again. When it says "No audio output device installed" on the list of playback devices, there is a static noise coming out of the headphones like a beat of a pulse. I tried reinstalling numerous times and still no difference. I also tried plugging in the USB in the back of the computer, but with same results, the headset becomes "unplugged" again. Thanks for reading and please try to help.

Yo, if you ever come back here(you last visited in March) We can probably help one another. The wires you are talking about are:
red/blue = V+ or volume up
red/green = MIC switch on/off
green/copper = G (ground for the LED)
FULL red = L or left earphone. I have this associated with tp7.
I have no wires connected to my circuit board. I have been using trial an error to identify what goes where. However I have been given ONE godsend. When the wires were ripped from the circuit board the white sheathed wire left a little section on the circuit board identifying it as tp5.
IF all you have is the four missing connections you could easily use trial n error. Touching the missing wires to each node.
for the mic switch. Open up ventrilo and get it listening for the mic.
process of elimination. Then you can do volume up. or get the led working by touching the ground to the nodes(possibly the easiest)
I'm going back to the drawing board with the the red wire.

Sound Blaster ZX mic muffled and low volume

Hey guys!
I'm having a bit of trouble with the microphone bundled with the ZX card. The ACM mic that is.
I'm not sure if it's the card or the mic, but my problem is that when recording or talking on Skype/TeamSpeak, my voice if very low (even tho I have all sliders maxed out) and it's muffled. It basically sounds like I'm talking in to a pillow.
If I connect the mic to the built-in Realtek crap on my motherboard, the sound recorded is sooo much clearer though.
I got to have both the volume and the mic boost maxed out in the Sound Blaster control panel to even hear myself at all. If I turn the noise reduction off the sound gets a bit clearer, but the static noise gets so bad it's unbearable.
Is my card faulty or is this a driver issue?

I have exactly the same problem. On Teamspeak my friends were complaining that I was barely audible and sounded muffled/distorted. I tried plugging my logitech desktop mic into the soundblaster, but this didn't solve the issue - so I presume the problem is not with the ACM mic. I also tried playing with the settings in the control panel, but this had little effect. Increasing the boost to 30db improves it slightly, but then the mc also starts picking up my fans and even movement from the headphone cable. Possibly a driver issue???
Like you I have had to resort to plugging my microphone into the onboard sound card.
In fact I've just realised that this problem is being discussed in another thread: http://forums.creative.com/showthrea...=699346&page=2

Creative Sound Blaster Audigy SE problems

Alright first of all I am new to Linux in general.
I have two soundcards in my computer. One is an onboard card (Intel) that is faulty and doesn't work; another is a Creative Sound Blaster Audigy SE which does work.
My problem, of course, is getting the latter to work.
So I realize this is nothing new, searching the forums and reading ALSA's wiki. However there seems to be some issues with making this work on ALSA, so is there a way to configure this with OSS?
"lspci | grep audio" returns both soundcards:
00:1f.5 Multimedia audio controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) AC'97 Audio Controller (rev 02)
01:00.0 Multimedia audio controller: Creative Labs CA0106 Soundblaster
"ossdetect -v" returns:
Detected Sound Blaster Audigy LS / Live7.1
Detected Intel AC97 (ICH5)
USB support available in the system, adding USB driver
Detected Generic USB audio/MIDI device (BETA)
I use "soundoff" and "soundon", then "osstest":
Sound subsystem and version: OSS 4.1 (b 1052/200903241101) (0x00040100)
Platform: Linux/i686 2.6.29-ARCH #1 SMP PREEMPT Wed Apr 8 12:47:56 UTC 2009
*** Scanning sound adapter #-1 ***
/dev/oss/oss_audigyls0/pcm0 (audio engine 0): AudigyLS front
- Performing audio playback test...
<left> Device returned error: Input/output error
/dev/oss/oss_audigyls0/pcm1 (audio engine 2): AudigyLS center/lfe
- Performing audio playback test...
<left> Device returned error: Input/output error
/dev/oss/oss_audigyls0/pcm2 (audio engine 3): AudigyLS surround
- Performing audio playback test...
<left> Device returned error: Input/output error
/dev/oss/oss_audigyls0/pcm3 (audio engine 4): AudigyLS 5.1 output
- Skipping multi channel device
*** Scanning sound adapter #1 ***
/dev/oss/oss_ich0/pcm0 (audio engine 9): Intel ICH5 (24D5)
- Performing audio playback test...
<left> OK <right> OK <stereo> OK <measured srate 47982.00 Hz (-0.04%)>
*** Some errors were detected during the tests ***
Basically it seems like it detects the crappy onboard sound (which is unusable, I stress) and not my soundcard. I really don't know how to fix/configure this and sound is really important to me if I'll be using Arch.
Thanks for any help offered, if more information about something is needed I'll be more than happy to oblige.

I would start by disabling the on board sound in your BIOS if you are not going to use it. As a novice user much of the documentation kind of covers the simpler case and this might help you navigate them better.
Keep in mind the Audigy SE is not a real Audigy (like Audigy 2 which has very good linux support). If you are just looking for straightforward playback you should have no trouble, but you will not get hardware mixing with SE IIRC.

Sound Blaster ZxR - Whats going on, where is it?

Hello everyone looking for some answers here.
Wanting to know when the ZxR is going to be out in the UK. Everything I have seen has spoken about early December, this is now the last day of. So what's going on here? The release date has passed and I still cannot find anything explaining it from you guys? I have been waiting nearly a year to upgrade my faulty Sound Blaster X-Fi that has finally died after years of hardcore service and to be honest none of the recent creative cards have been worth swapping it for. Honestly if this card isnt out soon I'll just have to buy a Xonar or something I have always been a creative customer never bought anything other than your sound cards but this is just a joke now and is definitely going to lose your company customers.
I would like some actual information on when it is coming out or if you don't know the proper reason why it isn't out. If its due to faults or issues your customers would want to know this, it would make them happier that you care about quality of use for example. Ignoring us just makes people get annoyed and turn away
Look forward to a reply
Greg M
Glasgow, UK

That's still the bare minimum of information, and still as vaige as it can be... Can't you guys do better than this? where the f... is the customer satisfaction? this is almost funny how bad this is :/
I suppose I will wait 14 more days if I cant get it by the 18th I'll just go get a card from another company. It wont be what I want but atleast I CAN get one and the customer service will be a bit better Creative you need to pull yourselves together I am very disappointed with this company lately. Can't even get a good sound card from my favourite manufacturer. I will just have to keep listening to my Zen Vision:M YES I HAVE ONE OF THEM TOO!!!

Sound Blaster Tactic3d alpha problems

Hi, i have some problems with installing Sound Blaster Tactic3d alpha drivers.
First is that i don't have pannel after installing drivers and second one is that my microphone is muted. Can someone help me ?
*EDIT*
Problems fixed (downloaded and installed this : http://www.userdrivers.com/Sound-Card/Creative-Sound-Blaster-Tactic3D-Alpha-Pack--0-000-for-Windo... ), but now control pannel is freezing on pop up.

Hi,
This could be caused by residual files from previous installation. It would advisable to uninstall and reinstall the package with a clean boot of your system. This article may help.

Sound blaster ZXR not detected

Hi,
I just popped in the ZXR, both cards, in my computer after i uninstalled the old xfi Xtreme music physically and all software. In bios the card is seen in the slot that i've put it in. When i boot in windows it doesn't find the card in the device manager or if i install the driver.
Things i already tried:
- disabled fast boot
- in the bios meniu for PCX OpRom settings: first - legacy support only; second try - UEFI support only in the.
- default settings in bios
- disconnected the 2 cards and left just the main in.
I'm running a Z87 chipset motherboard.
here is a dxdiag file:
http://www65.zippyshare.com/v/97450374/file.html
Any more suggestion about what to do?

Thanks, for the help! The problem was me... i was trying to install another driver that wasn't for my sound card. i just installed the driver from the cd in the box and it worked. The funny thing is that windows didn't see any new hardware in the pc but after i installed the driver from the cd the sound card appeared.
Again thanks!

Windows Vista vs. Sound Blaster Audigy Value = Problem

I am facing problems with SoundBlaster Audigy Value when using it with Windows Vista. However i have downloaded and installed latest drivers (Version No. - SB24_VTDRV_LB__04_0077) supporting this card but still it is functioning as good as it worked with windows XP .
Prob # : I can hear sound from my TV Tuner device but cannot perform recording , an error ("Cannot render audio capture system") is generated whenever i try to do so. I also tried to set recording control of my Tv Tuner device to sound card's "line in" parameter as i used to do in XP but in Vista my device shows nothing. Why ?
Prob # 2: Can you tell me where I can find "creative graphic equalizer" for this card which supports windows Vista or please provide a link to download it's
Prob # 3: Why we cannot enable "Bass Boost" using new Creative Audio Console while using Creative Inspire 4400 (4. Channel Speakers) like i used to do in windows XP ?
I will be extremely thankful to you if you please provide a solution to these problems.
Thank You........

altho i tried this with audigy se u might wanna check this
http://forums.creative.com/creativelabs/board/message?board.id=Vista&message.id=7665#M7665

5.1 Optical Output on Sound blaster ZxR - Some questions

This may have been discussed before but I still cannot seem to find the answer! Anyway, I have a ZxR connected via optical S/PDIF out to a home theatre processor which supports Dolby Digital and DTS.
The manual states:
DTS Connect is a real-time encoding technology from DTS,Inc. for interactive media and is only available on the PC platform. Itconverts any audio signal on the computer into 5.1 channel DTS format andtransports it via a single digital cable.
In the software I select dts connect as the encoder. In widows I select the ZxR S/PDIF option as the default playback device, however I don't see 5.1 as an option when I go to properties/default format dropdown. I'm not sure if this should only appear when I am looking at the properties for analogue speaker options?
Anyway, when playing CD's I get a dts signal to the processor when using Power DVD or DBpoweramp's CD Ripper software. Foobar and Windows Media Player throws up unrecoverable errors. Anyone know why?
I tried playing Dragon age 2 game. Analogue connections give good surround sound. Dts Optical gives no sound at all. Will this be true for all games?
Finally, playing DVD's with Power DVD gives dts surround via optical OK. but strangely in the Power DVD's sound options I have to set it as 6 channel. If I use S/PDIF as the output I get no sound? I was under the impression that the DVD player software needed to be in throughput mode? Again I'm confused at this.
So, any help on the above or experiences using the optical out to a surround processor welcome!
Thanks,
Paul

1 rule, if you want 5.1 than configure everything for 5.1 even if it's not obviously related to optical sound. 2nd if you want the ZxR DTS encoder to "work" you just have to select it in the creative SBX menu and like it says underneath in that window leave your other output settings (windows) to speakers. Troughput mode is there for the DVD player to send your sound straight to your external decoder and your sound card does nothing with it.
You might want to read my thread, there is a lot of knowhow in it.
http://forums.creative.com/showthread.php?t=700132

Sound Blaster Live (Mic proble

I am a guitar player and I use a program called Guitar Pro to read sheet music and to tune my guitar quickly. However ever since I got a SB Li've it hasn't worked at all.
The microphones will record but only if I have my guitar at a crazy crazy volume.
I know it's the microphones because I've tried four different mics already (one being new out of the box).
I have the record volume all the way (even with mic boost 20db) and all options are all the way up. Anyone have any idea?

cowadvance, have you also tried increasing the volume at the Control Panel for Sounds and Audio Devices Properities?Hope that will help you.

Sound blaster 5.1 vx problem(headphones)

(sound blaster 5. vx problem(headphones)& guys i have bought sound blaster 5. vx and they are giving me awsome output on the creative 2. speakers
but the main problem is tht i want to play fps games with eax support and tht can be done by headphones
but soundblaster 5. VX is giving me a very bad output and the voulme is too low and i cant make out wht to and wht not to do
i tried everything to increase my headphones output in the software but i failed plz help me mods
p.s. the headphones is giving me awsome output on motherboard sound card but not on sound blaster
so plz tell me
the sound blaster is ok i suppose.otherswise it would have given me bad output on 2. also
my headphones are moserbaer mb 370 plz help me anyone

hey someone help me i am getting frustrated
plz help me anyone

Sound blaster xfi extreme music

I have been trying to download the driver for the above hardware, but everytime it comes up with broken link web page just as i press the agree button to the terms and condition page.. can somebody help please...

Hi,
Refer to this thread http:// forums.creative.com/t5/Sound-Blaster/driver-download-problem/m-p/565953/highlight/false#M58477 and download the driver posted in message 7.

Sound blaster zxr mic problem

Similar Messages

Maybe you are looking for