Sound Card for Power Mac G4 Quicksilver

I was having a look around for sound cards for the Power Mac G4 Quicksilver and read about the M-Audio Revolution 5.1 and 7.1. Are these the best sound cards available for the G4 Quicksilver? Are there better ones?
Sam

I've started using the iMic by Griffin. It's an USB stereo input/output audio adapter with both mic and line level input/ouput. They provide a free download of their audio editing software called Finyl Vinyl (I think), which lets you record and edit audio mainly (though you can input video with the adapter - need different software though). Though it's intended mainly for recording from turntables, you can input and edit most any audio with a mini plug to RCA jacks cable. I've used a cassette deck and a mini disc recorder so far. I haven't played much with the mic input so far, but the line in audio is very good (I've worked in community radio for a while now, so I have a pretty good ear). The adapter also works with other audio editing software like Audacity and Logic Express (possibly Garageband too, I haven't tried). And it's available for under $30 on places like eBay.
http://www.griffintechnology.com/products/imic

Similar Messages

Sound Card for Power Mac G5 (Late 2005)

Hi folks, I'm sure this question has probably been asked here before but I'll appreciate it if someone could give me some info on pci-e sound cards for the late 2005 Power Mac G5.

Hi Joe Goes;
Instead of going to PCIe cards which I think would be extreme expensive, I would suggest connecting the optical cables to a receiver or amp and then connecting the multiple set of speakers to it. Which is what I did. I picked up an amp at used equipment table at the local sound store for nearly nothing. In fact the optical cables I needed cost me more the amp if you can believe that.
Allan

Sound Card for the Mac Pro

Hello,
I've searched around but can't seem to find any definitive answer to buying a sound card for my Mac Pro. I want to plug in a guitar and microphone for garageband and voice overs on FCP. Any ideas?
Thanks,
Jake

Best look for usb/fw audio interfaces which can be inexpensive and easy to get up an running.
There are many many cards on the market all depending on how many I/O you are chasing and overall sonic results.
If your in the market for entry level cards - check out
www.m-audio.com
www.focusrite.com
www.digidesign.com
or
if your in the semi-pro market, look at www.rme-audio.com (mainly the fireface series)
My pick if you are an entry level user wanting a great 2in/2out interface, have a look at the Duet by Apogee.
http://www.apogeedigital.com/
(I use all their top end pro kit and can tell you they are a very good company in both product and support)

Need new low-end graphics card for Power Mac G5 (PowerPC 970)

My Power Mac G5 (PowerPC 970) has recently died I believe due to a bad
ATI RADEON X800 XT MAC EDITION video card.
Reason for thinking its the card, is that the machine was performing its intended tasks for several days even though the monitor was snow.
Having trouble determining a low-end replacement. (I no longer need the enhanced features of the RADEON X800 for this machine.
Much appreciated if someone could suggest a product appropriate for PowerPC 970.
Thanks!

I also ran into this issue with my dual G5. When I bought it, I didn't get wireless because it was a dedicated desktop on the network, but I'm upgrading and giving it to the kids to use in a room without wired network. Now that wireless would be really nice and it looks like the official solution is:
"Apple Wireless Upgrade Kit for Power Mac G5 Dual or Power Mac G5 Quad MA252G/A"
which is really expensive and difficult to install. But the weird thing is that I do have bluetooth. I wonder if there's just some little doodad I need to connect to get wireless going too, but I can't find any info on the card, and it looks like it's buried on the motherboard behind all the cooling stuff. I'll probably just spring for one of the USB solutions.

Best graphics card for power mac g4 500 dual

I recently acquired a power mac g4 500 dual core processor, and i'm looking for an upgrade for the graphics card. I currently have the stock ATI rage 128 pro, and it doesn't seem to cut it very well, especially since I installed 10.5 leopard on it (hacked through open-firmware). I've been doing some research, and I've had a hard time finding the best upgrade. I'm not looking to really play any games or do anything graphics intensive, I just want all the basic tasks to be quicker. I'm looking for something that supports Quartz extreme, and possibly core image. Thanks.
-Aaron

Hi-
Leopard needs Core Image. The best card is the Radeon 9800 Pro Mac edition.

Which card for Power Mac G3

Which airport card do I need for my Power Mac G3?
I found (through this discussion forum) a list of which computers need the "original" airport card and which computers need the airport extreme card, but I cannot find Power Mac G3 on either list.
I am also wondering whether Apple still sells the older cards.

The Powermac G3 is not on the list because... no PowerMac G3 model is "Airport ready". PowerMac G3s were manufactured before Apple developed the Airport wireless networking system.
You need a non-Apple solution such as:
1. a PCI card based wireless adapter with MacOS driver support such as:
http://www.macwireless.com/html/products/11g11bcards/11gPCI.php
2. a wireless bridge device designed to connect to your Mac's ethernet port like the Linksys WET54G or the Netgear WGE111.

AirPort Extreme Card for Power Mac G5 (August 2005) 7,3

I've Power Mac G5 (August 2005) Model 7,3 (Model M9748)
Is this Airport Extreme Card the right one for my mac:
1. Airport Extreme Wireless Card 802.11G A1026
Is there any difference between M8881LL/A A1026 and 802.11G A1026 or are they the same?

Shree, Welcome to the discussion area!
Yes that card is what you need. No there is no difference between the cards referenced with those terms.

Airport Extreme Card for power mac G5 help!!

I have a late 2005 Power mac G5. I got an Airport Extreme wireless card. I put the card in there, and there are 2 wires i presume or have read to presume they are used for the antenna. I attempt to put 1 wire in the port on the back of the card. The wire and the port on the back of the card do not match or plug in flush.
Then i remember I have the "T" shaped antenna and attempt to plug that into the back port of the airport extreme card. again it does not really fit flush in the back of the card.
What do i need to acquire to connect this card to either the wires or "T" shaped antenna. Ive seen some installation instructions and notice that some of the wires have a more suitable connector. Please help! Thanks, ~adam~

That computer accepts a combined AirPort and Bluetooth card; the standalone AirPort Extreme card can't be used with it even though it may fit onto the logic board. Click here for more information.
(44057)

Looking for Video Card for Power Mac G5 August 2005

I have a Power Mac G5 built August of 2005. My ATI Radeon X850 XT G5 Mac Edition 256MB Video Card is toast. Is it an AGP card? I need to replace it. Will the Apple G5 PowerMac ATi Radeon 9600 XT 128MB Video Card ADC DVI Graphics work on my G5?

The 9600 XT will work, but you won't be impressed after life with a X850.
The occasional X800XT OEM can still be found.
This trusted seller has OEM X800XT cards available.
Might get a bargain in this auction.
X850XT cards are dear when available.
IMO, the performance difference between X800 and X850 doesn't really justify $100...
http://www.barefeats.com/radx800.html
If you don't need the ADC port, a flashed FireGL X3 makes a nice dual DVI X800XT .
The Geforce 6800 Ultra DDL is always a performance value.

Sound card for my G4 quicksilver

can anyone point me in the direction of a cheap sound card for my quicksilver?
i want to fit it with an optical output to connect it to a surround system just like newer powermac models. i will not be needing a bunch of analog outputs or any inputs. i want to make this as cheap as possible.
any suggestions?

Dear Hans-Marius ?verland,
...can anyone point me in the direction of a cheap sound card for my quicksilver?...
Well, I don't know how much cheap you want this sound card you're after, but I reccon that the M-Audio Revolution 5.1 PCI card would certainly return you the best bang for your buks.
It's Mac OSX savvy and plays DOLBY 5.1 surround GREAT!
At under US$100,00 I haven't found anything better so far.
Hope the above is of some help to you.
Ciao.
Costa

Suggest me a usb sound card for mac mini

please suggest me a usb sound card for mac mini (i need 5.1 sound)

The Griffin Technology FireWave will give you the 3 'cables' ("FireWave outputs six channel audio through three 1/8” (3.5mm) stereo mini-jacks: Left/Right, Center/Subwoofer and Right Surround/Left Surround.") connection for surround sound (speakers) audio. Whether or not a particular headphone set is compatible, you might ask Griffin directly about that. If you're playing a DVD with VLC or the Apple DVD Player, you will get surround sound. But, you'd have to find an MP3 with multi-channel audio inside it to play surround sound out of iTunes.
-Doug

Sound Card for Mac Pro?

I've come over to a Mac Pro after PC's for many years. My PC had a sound card that accepted the 1/8 mini plugs of my Klipsch 4.1 Pro Media speakers. I would plug into the front and rear outputs on the sound card. The Mac Pro only has 1 analog output.
Is the only answer, to get a Y adapter, to connect the front and rear speakers, or do I need to get a sound card?

I connect my Klipsch Pro Media 5.1s through a Creative Digital Decoder (DDTS-100) which is connected through optical cable to my Mac Pro.
Crystal clear 5.1 THX certified sound.

Power Mac G4 Quicksilver Won't Wake From Sleep

I have a Power Mac G4 Quicksilver 933MHz that will not wake up after it goes to sleep. It is currently running OS X 10.3, has had its hard drive replaced, system reinstalled, and been DiskWarrior'd. Haven't tried replacing the PRAM battery yet but get no indication its dead (clock keeps time wen off). It always connected to an Apple 17" Cinema Display--could that be the source of the problem?

Hi, Toolshed4!
Third Party USB devices and USB PCI cards are notorious potential culprits for no wake from sleep issues so please follow japamac's lead and look at them as potential culprits. Disconnect the external peripherals and test sleep/wake. Swap a third party keyboard and/or mouse with your Apple one(s) and test. Remove any PCI cards, and test. (It's perhaps good practice to reset the PMU after you add or remove an internal component.)
A Cinema Display, especially one with a built-in USB port or hub problem, could create an issue, though it would more likely to be one of not sleeping, rather than not waking. You might quickly check your system log for possible indicators of USB issues with the Display, if you have reason to suspect that its ports may not be functioning properly.
Resetting NVRAM in Open Firmware sometimes resolves the issue. Resetting your PMU as japamac suggested will take care of the NVRAM reset for you.
If the above didn't resolve things, please continue on...
Corrupt Energy Saver preferences are sometimes the cause. Quit System Preferences if it's opened and navigate to /Library/Preferences/System Configuration (folder) and delete the following preference files:
com.apple.PowerManagement.plist
com.apple.AutoWake.plist
(The AutoWake plist file may or may not be present, depending on whether or not you have/had scheduled sleep settings.)
Then navigate to ~/Library/Preferences and delete the com.apple.systemuiserver.plist preference file. Restart and test sleep again.
If your battery is old, it's a good idea to just get a new one. The worst that can happen is that you'll have a spare when you need it. They're about $5 online. If you go to Radio Shack with the one you have, they'll test it for you. Alternately, put a voltmeter on it and insure that you're reading at least 3.3 volts DC. New ones read 3.6 - 3.9 volts.
Gary
Message was edited by: Majordadusma

Wireless Net card for old PM G4 Quicksilver

Hey alllll, does anyone know which non-Apple wirless PCI or even USB card might work with a PowerMac G4 Quicksilver 800mhz?
Using latest OS etc..
I don't really want to run cables everywhere in my new clean crisp office...:-))
Thanks,
X
QS 800mhz 1.5GB RAM, Dual Raptors, Radeon 9000
PM G4, dual raptors, Powerbook G4, 23inch display, ipod vido, nano and more and more...

Xerxes, welcome, see the post below "I NEED A WIRELESS CARD FOR MY MAC".
Joe
Power Mac G4 Gigabit Ethernet Mac OS X (10.3.9) 1.5 GB Ram, ENCORE/ST G4, Tempo SATA, ATI Radeon 9000, Adaptec 4000

Powering ON/OFF Problems on a Power Mac G4 (Quicksilver Order M8360LL/A)

Hi G4 Specialists !
I have a major problem. @ First Model description:
Power Mac G4 (Quicksilver Order M8360LL/A)
System version : Mac OS X 10.4.8
Boot volume : Eclypse
Hardware Overview:
Machine speed : 867 MHz
Bus speed : 133 MHz
Number of processors : 1
L2 cache size : 256K
L3 cache size : 2MB
Machine model : Power Mac G4 (version = 2.1)
Boot ROM info : 4.2.3f1
Customer serial number : #######-###-####
Sales order number : Not available
Memory Overview:
Location Type Size
DIMM0/J21 SDRAM 128 MB
DIMM1/J22 SDRAM 256 MB
DIMM2/J23 SDRAM 256 MB
DIMM3/J24 empty
Network Overview:
Built-in:
Devices and Volumes
PCI:
SLOT-1(AGP):
Card Type : display
Card Name : NVDA,NVMac
Card Model : GeForce2 MX
Card (Video) Memory : 32 MB
Hard Drive:
Disk Size : 57.26 GB (1K = 1024) 62 GB (1K = 1000)
Unit Number : 0
ATA Device Type : ata
Device Serial : #######-###-####
Device Revision : ER6OA44A
Device Model : IBM-IC35L060AVER07-0
Eclypse:
Volume Size : 57.26 GB (1K = 1024) 62 GB (1K = 1000)
Ejectable : No
Writable : Yes
Hard Drive:
Disk Size : 37.27 GB (1K = 1024) 41 GB (1K = 1000)
Unit Number : 1
ATA Device Type : ata
Device Serial : WD-WMAD11234827
Device Revision : 05.03E05
Device Model : WDC WD400BB-00DEA0
CD-RW/DVD-R:
Disc Burning : Fully supported.
ATA Device Type : atapi
Device Revision : 1.90
Product Identification : DVD-RW DVR-103
Vendor Identification : PIONEER
Now the Problem:
in the last time I ear that the G4 after clicking on the Login Window on SLEEP is often gone to shutdown. The last week I made this check and the G4 gone to shutdown and after x seconds again ON without external intervention. Was this not a real shutdown (the light on the Power button was NOT PULSING)
What I have just done:
I resetted trought booting + OF all Boot parameters, I made the CUDA reset, I bought a new PMU Battery and now (all disconnected also the HDs) when I push the Power Botton the Fan TRIES to go but after a microsecond is cutted off power. The last time, while trying to take care of my G4, that it had made a little of work was tonight WHITOUT PMU/Battery I made login, I have seen that THE DATE WAS RIGHT (without PMU-Battery !!!) I just choose the right Display Conf, then I started DiskUtility first CHECK Disk and then I was looking for solutions @apple Support on another machine PUFF the G4 has gone OFF and ON and OFF than I unplugged the POWER cable.
Now I don t know any more, suggestions ?
Massimo
G4 QuickSilver 867, G4 PB 867, Classic Mac OS X (10.4.8)

Massimo,
I'm having a bit of a problem with the translation. I think what you're saying is that when you attempt startup, the Mac initially gets only a momentary bit of power, with the red LED lighting briefly, then shutting off, after which nothing happens. Occasionally, the Mac starts to the point where the hard drives begin to spin up, but then they, too, shut down. You would like to try booting to the install disc with the drives disconnected, but can't get far enough along in the startup process to open the optical drive tray.
If what I've said above is correct, you can open your optical drive tray manually. Use a fingernail to open the dust cover of the optical drive and look for a tiny hole on the face of the drive below the tray. If you insert a paperclip straight into this hole and push it firmly, the drive tray will begin to eject. When it comes out far enough to grasp with your fingers, pull it out to extend it fully. Insert the disc and manually push the tray back in. Boot to disc by depressing the "c" key at startup and holding it down until the turning grey cog wheel appears.
To attempt to get the Mac to start, perhaps you should try completely de-energizing and resetting it. Try this, (just leave your hard drives disconnected):
Disconnect everything externally except the power cord.
Touch your finger to a metal slot cover on the back of the Mac as a static discharge precaution, then disconnect the power cord.
Remove the battery.
Depress and hold the front power button for a five-count.
Fully depress the PMU for a five-count.
Take a thirty-minute break to insure that the internal capacitors are completely discharged.
Reconnect the power cord, monitor, keyboard, and mouse, leaving the battery out.
Attempt startup to the install disc.
Any luck? If so, reinsert the battery, connect the hard drives and boot to disc, launching Disk Utility and running Repair Disk and Repair Permissions. Check the Startup Disk option in the Installer menubar to insure the OS X system on your startup drive is still selected. Then quit the Installer to restart normally to the hard drive. If successful, you can then check the preference files for sleep-wake problem that it seems you were having, if I understood correctly.
BTW - When you get stuck in a situation where the Mac won't respond and you have difficulty powering down, try to avoid pulling the power plug, which can corrupt your files and drive directory if the drive is writing data. Instead, try the restart button if you have to force a complete shutdown. If that fails to work after holding it in for a few seconds, then try the power button. If it still won't power down after holding in the power button, then release it and immediately depress the restart button, which usually works. Pull the power plug on a running Mac only as a last resort. In any event, after any sudden shutdown, it's prudent practice to initially boot back to your Tiger install disc and run Repair Disk on the startup volume. If it isn't handy, then boot to Safe Mode by depressing the shift key at the next startup, which will force a file system check of the startup volume, which is like running Repair Disk without being able to see the results. Another way is to boot to single-user mode (depress & hold cmd+"s" at startup) and run fsck, where you'll be able to see the results of the drive repair.
Gary
1GHz DP G4 Quicksilver 2002, 400MHz B&W rev.2 G3, Mac SE30 Mac OS X (10.4.5) 5G iPod, Epson 2200 & R300 & LW Select 360 Printers, Epson 3200 Scanner

Sound Card for Power Mac G4 Quicksilver

Similar Messages

Maybe you are looking for