Sound from one speaker

I only get sound playback in one speaker when playing a short recording thru QT Player 7, and QT Player. The video is recored on a go pro hero 2, using a radio shack #274-397 3.5mm stereo male to 2.5mm stereo female adapter and a Drift audio external mic.

never was an answer to this question.

Similar Messages

  • Scratchy sound from one speaker- a35-s209

    was given laptop and warned about "sound issues". seems one speaker ok, other speaker scratchy,no volume. volume control on side of laptop seems intermittent,too. tried contact cleaner and cycling control, no joy. feel issues are related, but scared to do a teardown to get to control. could it be driver? any suggestions?
    Solved!
    Go to Solution.

    during remote assistance from my brother, he remembered a situation in which a line-in input interfered with sound. went to volume control and muted line-in. sound cleared up immediately. thanks bro,great catch!

  • Only hear sound from one speaker

    I have been going nuts trying to find help on this. There were some but not exactly the same. So here is my dilemma.
    I am capturing miniDV footage from my camera (Sony DVR PC 330) and used a Sennheiser MKE 300 Shotgun Video Camera Mike to capture audio. Then I captured in into FCE and also Toast 6. Both only produced audio on the left side. Now I checked the speakers, used headset and it was the same. I listened to iTunes and audio from other sources and both speakers and headset worked fine on both sides. Only bringing in from my camera did the sound from only the left speaker. So it's my camera or external mic. Well, I checked that too and I listened to the tape with headsets and heard everything fine on both sides. So the tape has all the audio. So could it be that the firewire is bad? Or is there something I have overlooked. Last week I imported a CD into FCE and produced a CD of audio that was fine. So the program is not at fault I would think. Any ideas would be great.
    iMac G5   Mac OS X (10.3.9)  

    Panning on audio . . . . .>
    The panning is set all the way to the left and shows -1. But this is the default setting. As when you click the little red (x) it will go to the left. And I just opened another project that works fine and it is all the way left with -1. If I move that sequence it sound less full with not bass or something, it just isn't right. So not sure this is the solution. And now I have to go out of town for a few days so will look forward to any other thoughts you all have when I return. Keep thinking
    Jon

  • Faulty sound from one speaker due to jack plug on unit

    Hi
    I realize that my system is prehistoric (Cambridge Desk Top Theatre 5.1 DTT2200) but it works fine EXCEPT for one problem - the centre speaker doesn't have any sound
    I have checked the integrity of both the speaker itself and the cable by swapping around so it must be down to the jack plug on the back of the unit
    Any suggestions?
    Would it be worth taking the bass unit apart and seeing if there is a loose connection or something? Or would I risk destroying the unit completely?!
    Although the system is old, I imagine that the problem would be relevant to later systems too
    Many thanks
    bobbycow

    You probably already checked in system preferences (lightswitch with apple on it) that on the output tab under sound the balance is set to the middle? I've seen where this has, for no apparent reason, moved to one extreme. If that's not the issue, you can try resetting the PRAM: http://support.apple.com/kb/HT1379

  • Sound on one speaker only

    Last night, while using iChat with another Mac user I was only getting sound from one speaker (right). Both speakers work with iTunes so it's not my hardware (I don't think it is anyway). Could this just be poor bandwidth?
    Thanks.
    MacBook Pro   Mac OS X (10.4.6)  

    Hi MacBoy70,
    This is the iChat software preventing you getting feedback as the MacBook Pro internal Mic is in the left hand speaker grill.
    4:30 PM Thursday; May 18, 2006

  • 17 inch late 2011 MBP with no sound from right speaker (Help)

    Hello community,
    I purchased a new MBP 17inch model and noticed sound only comes from one speaker.  I've checked the system preferences and moved the balance 100% to the right and no sound at all.  I don't believe this is normal, but before I make a case I wanted to speak with the community first. All responses are appreciated Thank you.

    Before you take it in, try resetting Pram.
    http://support.apple.com/kb/ht1379
    and SMC if that didn't work.
    http://support.apple.com/kb/HT3964

  • Airtunes Audio from One Speaker Only

    I've been running my Airtunes device for about a month now. However, I've just noticed that the sound is only coming from one speaker. I have done all the normal things such as changed the speakers, and changed the audio cable, but the problem persists. Apart from that, the devices exhibits no other problems.
    Before I send it back on warranty, anyone have any ideas on what I might be able to check. TIA.

    Have the same problem mate...really annoying.... i went and bought a better quality cable but to no avail!! Bringing it to local mac service place tomorrow to get it checked out. Looks like the stereo input port is wrecked!!

  • SOUND OF ONE SPEAKER OF NOKIA BH103 BLUETOOTH HEAD...

    SOUND OF ONE SPEAKER OF NOKIA BH103 BLUETOOTH HEADSET IS TOO LOW..I RESETED THE HEADSET..THEN TOO,THE PROBLEM PERSISTS

    Hi: i am able to do the pairing and I can use the handsfree phone but I cannot hear the sound from my U tube through my stereo headset. Can you help.

  • Sound from the speaker iPhone 4S 5.1.1. disappeared!?

    About one hour ago I lost the sound from the speaker iPhone 4S 5.1.1. Lost in the middle of a conversation with a friend whom I put on speakerfon, first started to choking and after that sound is disappeared, and than appears in the fraction of a second and after is completely gone. On two occasions it choking when I put some videos and that's all. There is no sound even when someone call me, only vibrates. Note that phone was never dropped, as a new one, and I got it from July last year. Headphones works normaly. Any help without service?

    Try This...
    Close All Open Apps...  Perform a Reset... Try again...
    Reset  ( No Data will be Lost )
    Press and hold the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears. Release the Buttons.
    http://support.apple.com/kb/ht1430
    More Info Here  >  http://support.apple.com/kb/TS2802

  • Moving sound from one clip to another?

    Can I take the sound from one clip and move it so that it plays during another clip?
    In other words, if I have some narration in one clip that would be better in another clip, can I pluck out that sound (narration) and re-locate it so that it plays at the same time another clip (video) is playing?
    I know that FCP can do this..you just cut out the sound portion you want and cut/paste it into whereever you want, beneath the visual part of whatever clip you want it to play with.
    thanks!
    ray

    Is it possible to take sound from one clip and put it in another clip?
    Yes

  • TS1630 Hi I have a problem with my iPhone 4S,  I have no sound from my speaker ,keyboard or notifications ,  and my volume control buttons are not working is anyone experiencing this? Any help would be great full, also I have reset the iPhone many times.

    Hi I have a problem with my iPhone 4S I have no sound from my speaker , keyboard, notifications.   or volume controls,  I have reset my iphone many times and still the same, any advise will be greatful
    Thanks

    I don't think that a software update from Apple will solve the issues that you are having. You have a rogue installation. After you posted I have just done the following:
    Disk Utility can verify  my partitioned Volume (including my boot disk) AND REPAIR the non-boot disks on the same Volume without a glitch. It repairs the non-boot disks containing data smoothly.
    I have used Mail to send some mails from some Yahoo and Hotmail accounts to my Thunderbird client containing GMail accounts - absolutely normal.
    I have iLife '09 but my iMovie '09 and iPhoto '09 open in a jiffy and I see no issues here. I have 6GB RAM (Maximum) on an early 2008 Macbook Pro with a 750GB hard drive partitioned with 120GB reserved for the Boot Drive.
    I am sorry that I cannot help further but I am sure there must be a way to reinstall the software without having to revert to restoring your ML backup. I have two clones and if you have such I would attempt to do that through that rather than through Time Machine - that is of course if you have a cloned drive.
    Good luck!

  • No audio from one speaker using the front jack

    I have an hpe-230f. Today I tried to use my headphones and I found out that I only got sound with one speaker.  I used a few other sets of headphones and got the same result. The sound jack on the rear is fine so I suspect that the front port dongle/cable is faulty. 
    I contacted HP support to try to get them to send me a replacement front dongle but they want me to send it in but I can't because I need the computer for schoolwork and if they end up reformatting my hard drive while it's being serviced I''ll be stuck on the phone with Microsoft for quite some time trying to get them to reacivate my Office 2007 key .
    Any ideas?

    Hi,
    Try the following.
    Shut down the notebook, unplug the AC Adapter and then remove the battery.  Hold  down the Power button for 30 seconds.  Re-insert the battery and plug in the AC Adapter.
    Tap away at the esc key as you start the notebook to launch the Start-up Menu and then select f10 to enter the bios menu.  Press f5 to load the defaults ( this is sometimes f9, but the menu at the bottom will show the correct key ), use the arrow keys to select 'Yes' and hit enter.  Press f10 to save the setting and again use the arrow keys to select 'Yes' and hit enter.

  • No Sound From Center Speaker [Win 7]

    $No Sound From Center Speaker [Win 7]? Hi,
    I downloaded the Darkest of Days demo and noticed that the speech volume was very low if i positioned it center of the camera. But if i positioned it on the left or right of the camera, the speech volume would increase. I found it strange.
    I closed the game. And ran my speakers through window's speaker test. Every speaker responded with a sound. Unconvinced, i opened a few songs. That's when i noticed the center speaker wasn't producing a sound. Even on 5. content (movies & music) the center speaker wouldn't work.
    **bleep**, no wonder those AC3 movies had low speech and i had to manually boost the speech volume. I noticed the low sound in games before too...but i attributed it to the 5. surround thing. Guess i was wrong!
    System Rig:
    Intel Core 2 Duo E6400 @3.2Ghz
    Gigabyte P965-DS3
    [color="DarkOrange">ATi HD4850
    Twinmos 3xGB DDR2 800Mhz + GB OCZ 800 MHz
    Zalman 9700
    Creative Audigy2 ZS
    Creative Fatalty Gaming Headset
    250GB Seagate SATA-II 7200.0 8MB
    Enermax 535W PSU
    Logitech X-540 5. Speakers.

    Hi
    Can you clarify that are getting the voice when you play the DVDs/CDs?If you are not getting the voice and you are getting the sounds only? Then there could be some connectivity issue for Center Speaker.Pl check the connections .. Regds Balu

  • No sound from right speaker on Pavilion g6-1353ea after installing Windows 8

    I've had no sound from right speaker on my HP Pavilion g6-1353ea after installing Windows 8. I've checked all drivers, and have done the sound test in sound properties (left speaker beeps fine, but then nothing from the right). Anyone else having this problem/found a solution?!

    Hi,
    Try the following.
    Download the IDT Audio installer on the link below and save it to your Downloads folder.
    http://ftp.hp.com/pub/softpaq/sp59001-59500/sp59154.exe
    When done, open windows Control Panel, open Device Manager and open up Sound, Video and Game Controllers.  Right click the IDT device and select Uninstall - you should also get a prompt to remove the current driver, tick the box to allow this and then proceed with the uninstall.
    When complete, shut down the notebook, unplug the AC Adapter and then remove the battery.  Hold  down the Power button for 30 seconds.  Re-insert the battery and plug in the AC Adapter.
    Tap away at the esc key as you start the notebook to launch the Start-up Menu and then select f10 to enter the bios menu.  Press f5 to load the defaults ( this is sometimes f9, but the menu at the bottom will show the correct key ), use the arrow keys to select 'Yes' and hit enter.  Press f10 to save the setting and again use the arrow keys to select 'Yes' and hit enter.
    Let Windows fully load - it will automatically load an audio driver, but just let this complete.  Then open your Downloads folder, right click on the IDT installer and select 'Run as Administrator' to start the installation.  When this has completed, right click the speaker icon in the Taskbar and select Playback Devices.  Left click 'Speakers and Headphones' once to highlight it and then click the Set Default button - check if you now have audio in both speakers.
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • TS2771 only getting sound from one side of the headset.  Any fixes available?

    I have an used Ipod touch.  When i connect a headset, i only sound from one channel.  Any fixes out there?

    - Try cleaning out/blowing out the headphone jack. Try inserting/removing the plug a dozen times or so.
    Try the following to rule out a software problem
    - Reset the iPod. Nothing will be lost
    Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Reset all settings
    Go to Settings > General > Reset and tap Reset All Settings.
    All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
    - Restore from backup
    - Restore to factory settings/new iPod.
    - Make an appointment at the Genius Bar of an Apple store. Seems you have a bad headphone jack.
    Apple Retail Store - Genius Bar
    Apple will exchange your iPod for a refurbished one for this price. They do not fix yours.
    Apple - iPod Repair price
    A third-party place like the following will replace the jack for less. Google for more.
    iPhone Repair, Service & Parts: iPod Touch, iPad, MacBook Pro Screens
    Replace the jack yourself
    iPod Touch Repair – iFixit

Maybe you are looking for

  • Error in installing  NW04s SR1 Portal

    Hi all, I am trying o install NW04sSR1(usage type EP). During the installation it went past all the satges unitl it again got stuck in the Configure development Infrastructure stage(stage 34 of 35). The error it shows is (output of sapinst) : ERROR 2

  • How to purge BPEL data on 10.1.3.1

    Hi Experts, I want to purge OLD data on BPEL dehudration repositiory. a) I did read notes in Metalink and talks about 10.1.2.. However mine is 10.1.3 b) I also read the belwo url http://orasoa.blogspot.com/2007/02/delete-bulk-bpel-instances.html c) C

  • Register namespace prefixes in JDeveloper?

    Hi, Is it possible to register namespace prefixes for namespaces in JDeveloper, so you can use the same prefixes for the same elements in different BPEL processes? As it is JDeveloper generates prefixes like ns1, n2 etc. which makes BPEL code less re

  • Keep the TR850 information message on background process

    Hi gurus, Does anybody know if there is some way to keep de message above in background process? I have a scenario here with a RFC Function is called by R/3 system and because of this message on the process chain changing into this FM, the system giv

  • Black Fri PS CC & LR5 deal misleading : only implies you need to be CS3 or above owner after order

    I was on the Adobe website, when I saw this Black Friday deal for Photoshop CC and Lightroom 5. Upon clicking Join now, I got to the following page : From this page, I then read both the FAQ and the terms. The FAQ said the following : And the terms s