Sound not herd in Soundtrack Pro

I'm trying to record my voice in soundtrack pro and there is sound going in but no bounce in SP, no feedback either. Help Please! Thanks!~

Similar Messages

Sound Soap equivalent in Soundtrack Pro 2?

Does anyone know if there is an equivalent to Bias Sound Soap in Soundtrack Pro 2? Sound Soap clears hum and etc. while preserving the good sound. It has an easy to use interface - particularly important for newbies like me.

I haven't seen SoundSoap but Soundtrack Pro 2.0 has a "Noise Reduction" feature.
Here are the instructions :-
Noise Reduction
Some audio files contain unwanted noise, making it difficult to hear the voices, music, or
other content of the file. Soundtrack Pro features two commands, Set Noise Print and
Reduce Noise, that you can use together to reduce noise in an audio file or selection.
Set Noise Print
The Set Noise Print command lets you select part of an audio file containing only the
noise that you want to remove as a “noise print.” The noise print provides a signature of
the frequencies to reduce or remove from the file.
Setting the noise print before reducing noise is optional. If you do not set a noise print
before using the Reduce Noise command, Soundtrack Pro extracts a noise print from
the selected part of the audio file. If there is an existing noise print, it will be used, even
if it is from a different audio file, unless you set a new noise print.
To set part of an audio file as a noise print:
1 In the waveform display, select the part of the audio file containing only the noise you
want to reduce.
2 Choose Process > Noise Reduction > Set Noise Print.
The selected noise is stored as a noise print.
Reduce Noise
The Reduce Noise command uses the frequency content of the noise print to reduce
noise in the audio file or selection.
To reduce noise using the noise print:
1 In the waveform display, select the part of the audio file in which you want to reduce noise.
2 Choose Process > Noise Reduction > Reduce Noise.
The Reduce Noise dialog appears. In the Reduce Noise dialog, you can optionally set
the noise threshold and tone for noise reduction. You can also preview the noise
reduction with the dialog open.
The noise threshold determines the level below which audio in the noise print is
considered to be noise. Lowering the threshold results in only very low signals being
reduced, while raising the threshold results in more high-level signals being reduced.
To set the threshold of the noise reduction:
m In the Reduce Noise dialog, drag the Noise Threshold slider left to lower the threshold,
or drag it right to raise the threshold. You can also type a value (in decibels) in the
Noise Threshold field.
To set the amount of noise reduction:
m Drag the Reduction slider left to decrease the amount of noise reduction, or drag it
right to increase the amount of noise reduction.
To change the tone of the noise reduction:
m In the Reduce Noise dialog, drag the Tone Control slider left to preserve more
low-frequency content (bass), or drag it right to preserve high-frequency content
(treble) during noise reduction.
You can preview noise reduction with the Reduce Noise dialog open and adjust the
threshold and tone of noise reduction. You can also hear the audio file or selection with
and without noise reduction, or hear only the noise to be removed.
To preview the file with noise reduction:
m Click the Play button in the lower part of the Reduce Noise dialog.
To set the preview volume level:
m Drag the Volume slider in the lower part of the Reduce Noise dialog left to lower the
volume or right to raise the volume.
To compare the file with and without noise reduction:
m Click the Bypass button to hear the file without noise reduction. Click the button again
to hear the file with noise reduction.
To hear only the noise to be removed:
m Select the Noise Only checkbox.
To use a noise reduction preset:
1 In the Reduce Noise dialog, click Show Presets.
The Presets drawer appears.
2 In the Presets drawer, select a preset from either the Factory Presets or User Presets list.
3 Click Apply.
Is that simple enough ?
You can also set and add ambient noise.
Ian.

Sound engineer feedback on soundtrack pro

Hi..
the following comments are my feedback based on my job in sound engineering for tv commercials.
I love the software, nevertheless there are some features that I would love to see changed as soon as possible.
The faders' curve is so odd.. It makes them really hard to use, becouse the most important dB range, close to 0 (both up and down), have a really small room..
this way, mix precision is impossible
it looks like a classic fader with inverted curve...
same for metering and for track automation. that's really nasty.. please change it!!!
Also, metering without dB indicators is pretty annoying and many times useless (same as protools, a feature that I really hate).

I personally think that the 'Pro' suffix was a little premature. I would love to be able to use Soundtrack Pro for professional work, but it lacks so many of the features of the big guys!
Having to switch between editors to do simple fades for example, remind me of ProTools from 12 years ago. That is simply not good enough.
I would really love to know if any one is really using STPro for tv spots, documentaries etc... I keep trying, but with the lack of simple editing options found in other packages, I just keep going back to them. I mean, even LogicPro is better for spotting effects and editing 'post' audio.
I have been though the manual several times, after thinking, 'I must be missing something'.....

OMF files and AAF files from AVID not working in soundtrack Pro 2

OMF files from avid work in Logic studio but always need converting to 44.1K so are useless.
In Soundtrack Pro I can't get them in without about a million glitches. First of all it creates about four clips of every audio clip and dumps them in bulk at the begining of the time line in a great big jumble (sometimes it's not visible). Audio clips are often not selectable and it doesn't take the timecode from the OMF. It's a mess, don't apple test these things?
AAF - (files that I have checked do work on other systems) I can't get to work at all.
I can't export AAF or OMF either, even though the manuals say I can.

Look in the Utilities folder for Apple Loops Utility. The manual is in under the Help menu of that app.
2 posts in an hour with the same question . . . I hear an echo

Why is my FaceTime sound not working in Macbook Pro?

why is FaceTime sound not working in my Macbook Pro?

how do i get my sound back on my Macbook pro?

Sound not working in MacBook Pro OS X

Hello,
I have a mid 2011 MacBook Pro. The silica gel packet in my backpack broke and it went inside my Mac's headphone jack. I tried to remove it with a tooth pic, knife, cotton swab, cotton swab with glue etc etc. And finally sound stopped working when the sillica gel went deep inside. The volume icon is grayed out since then.
At times I see a red light from the headphone jack. I understand that the speaker is ok, because I have a parallel installation of windows and the sound works fine in that! I also hear sound via external speakers and bluetooth headset in OS X. I took it to the Apple Store and they told me that I had to replace the entire motherboard which might cost around $550! I am not ready to do that! Everything else works just fine!
Anyone knows any fix for this problem? My MacBook is mute for a long time

how do i get my sound back on my Macbook pro?

Logic 8 sound not working on Macbook Pro

Hi has anyone else had problems with the sound not working on a MacBook pro.
Build in audio works fine but when I launch Logic all i get is a clicking sound.
MacBook is brand new.
Thanks

yer i did the latest updates and have it configured right too. when i open up a new project it works but when i open a full track i made in logi 7 it does have any sound and makes clicking noise.
i am wondering if its a UB update on one of my plug-in's? god its annonying aaaaaaarrr

Surround Sound not working on Mac Pro (Early 2008)!

I'm writing this as my last ditch attempt to solve my problem.
Recently I bought a 5.1 Onkyo AV Receiver, model HT-R558 as for the audio output of my machine.
I have connected the device components, however when connected to my Mac using a TOSLINK cable, all i recieve is stereo sound through the front left, center, and front right speakers. - The rear speakers give no output, and the subwoofer only works in iTunes.
As far as I was aware the process was as follows:
Mac Pro with output set to Digital Out connected to the digital out port --> Optical/Toslink Cable --> connected to receiver (Onkyo HT-R558 through optical in on receiver.
I have followed several Knowledge Base articles with no success.
Is the Mac Pro actually capable of 5.1 sound output, or is it an added non-working feature?
I have tried a system utility called Perian, but no luck, also i have found articles saying this can be fixed with Terminal, no luck either.
If anyone has any advice on correctly connecting surround sound to my Mac I would be extremely grateful! I only hope there is something I have overlooked.
At the moment i am running the system using Pro Logic II, though it feels like a let down.

I found the problem, the digital out on my Mac Pro is only capable of outputting stereo, this appears to be an OS X 10.6.8 issue that would need to be addressed via a supplemental update.
I know DVD Player can output 5.1 when set up correctly, so can iTunes movies; unfortunately this appears to be a problem that only has few solutions.
1. Downgrade OS X to a version prior to 10.6.8 (however doing this causes incompatibility with my iOS devices.)
2. Add a PCI Express compatible sound card, or use an external card (requires additional hardware purchases.)
3. Use only stereo capable units with the machine (as anything with higher speaker configurations requires use of Pro Logic II from the receiver/amplifier; not to mention sounds terrible.)
Until, or if this is ever fixed I will stay with option 2, as it doesn't require use of additional software just to use audio, allows me to use the respective amplifier fully, and also sounds better.
Thank you for your advice, I just have to remember to be a little more careful when choosing audio products for use with Mac it seems.
I am closing this question.
Regards,
Peter.

Sound not working on MacBook Pro

the other night my earphones were plugged in to my MacBook Pro and it dropped on the floor and wedged the jack inside. I eventually managed to get it out but now the sound doesn't work at all. Any ideas how I can fix this? And will it be expensive?
any help would be appreciated, thank you!

I hope it isn't expensive either! I got told the logic board would need to be replaced but wasn't sure if I was being ripped off; surely there would be a separate component off it for the 3.5mm jack...
I'm not an expert though, so I will just carry on looking around and get a few more opinions!
Thank you for the advice

Sound not working on Macbook Pro 13in" 4gbRam late 2009

My macbook pro started going crazy and then the sound stoped working can someone help me?

Try SMC and PRAM resets:
http://support.apple.com/kb/HT3964
http://support.apple.com/kb/HT1379
Ciao.

Install Soundtrack Pro without Compressor 2

I've run in to major problems with Compressor 2. I am running Production Studio (FCP4.5, DVDSP3, etc). I purchased the Soundtrack Pro Upgrade and it also added Compressor 2. I have experienced many problems with compressor 2 (I've seen them listed here) and needed to totally rebuild to get back to a working system with Compressor 1. I tried many of the suggestions with little luck. I have not yet installed Soundtrack Pro, as I cannot afford to bring my system to a halt again with Compressor 2. Is there any way to install Soundtrack Pro without Compressor 2? I've been through the install and the documentation, but did not see the option. Anyone know any way to do this?

If you get Charles Srstka's Pacifist, you will be able to install whatever you need to wherever you want... Beware: this is not for the faint of heart - you must know what you're doing!
http://www.CharlesSoft.com/

Soundtrack Pro crashes on launch. New OS 10.6.6 update?

Hey all,
I just installed Logic Studio yesterday and updated to OS 10.6.6 today. Soundtrack Pro is crashing on start. Are these two issues related? Is anyone else having this problem?
The error report tells me this:
Dyld Error Message:
Library not loaded: /Library/Application Support/ProApps/SharedA/Frameworks/ProFX.framework/Versions/A/ProFX
Referenced from: /Applications/Soundtrack Pro.app/Contents/MacOS/Soundtrack Pro
Reason: image not found
Other details I have:
My Soundtrack Pro version is3.0.1. The only other audio apps I have are GarageBand '11 and Amadeus Pro.
I have restarted the computer, and I have repaired disk permissions.
Thanks in advance,
David
Message was edited by: David Sprunger

Ok, here's an update on my attempt. nolanscott, you state:
+reinstalling the old ProKit.framework 5.1 from TimeMachine again,+
+Soundtrack 1.5 opens again...+
+(HD / System / Library / PrivateFrameworks / ProKit.framework)+
I'm using Soundtrack Pro 3.0.1, and I don't find a "PrivateFrameworks" folder. But I did dig into a Mac Pro that has Final Cut Studio and did find what this iMac seems to be missing. But wow, not sure exactly how huge this is, but the ProApps directory on the iMac only has:
--Bundles [directory]
--Internal Plug-Ins [directory]
--Logic Studio System ID
--ProAppsSystemID
While the Mac Pro which has Final Cut Studio (admittedly no Logic Studio) has much more robust contents!:
--Bundles [directory]
--Final Cut Studio System ID
--Internal Plug-Ins [directory]
--MIO [directory]
-- ProAppsSystemID
-- SharedA [directory]
So, in the original error message I got, the entire ShareA folder doesn't even exist. The ShareA folder has 3000+ items in it. I've copied it on the corresponding location on the iMac (Volumes/Macintosh HD/Library/Application Support/ProApps/)... and SoundTrack Pro still fails. This time the relevant message is:
+Dyld Error Message:+
+Library not loaded: /Library/Frameworks/ProMetadataSupport.framework/Versions/A/ProMetadataSupport+
+Referenced from: /Applications/Soundtrack Pro.app/Contents/MacOS/Soundtrack Pro+
+Reason: image not found+
Again, comparing the two computers, inside of the iMac to the Mac Pro, the ProMetadataSupport.framework folder is absent from the iMac. I copy that folder over from the Mac Pro and...
BINGO. We have launch.
Now, the one thing about doing this is, that I assume I'm not the only Soundtrack Pro'er out there who is having this problem. I don't know what this will do when Apple releases and update for this. Will my fix cause new problems that conflict with Apples? Or did this in fact having nothing to do with updating to 10.6.6 and stem from something else I did? All I did was install Logic Studio, and run System Update. Didn't launch Soundtrack until after I had updated to 10.6.6, so don't know if the problem is connected to that...
Thanks nolanscott for inspiring my research!
--David

Soundtrack Pro 3 training

I'd like to get some basic training in Soundtrack Pro 3 that could get me started as a novice. I've cracked opened Soundtrack a few times and played around with it, but I really didn't know what I was doing. I know some stuff about working with sound, and most of the components in Soundtrack are things I understand, but I need something to get me started.
I've enjoyed stuff from Ripple Training in the past, but the only thing I see there is their "Sound Editing & Mastering in Soundtrack Pro" package. Scanning through the lessons, this looks extremely complex. I'm looking for something more along the line of their "Motion Fast Forward" series.
Any suggestions?

Robert,
I have "Motion 3 Fast Forward" and at least one other package from Ripple Training, and these work well for me. However, the description of the Soundtrack package says, "Whether you're an editor working in Final Cut Pro, or a dedicated sound mixer with experience using other audio workstations, this tutorial presents a complete picture on how to edit, process, mix and ultimately master your soundtracks using Apple' Soundtrack Pro 2."
To me, that sounds more complex, but I'm hearing you say that isn't the case. Correct?
I DO know a fair amount about audio, I'm just looking for a resource that will give me clear instructions about how to get where I want to go.

Why my Logic Studio 9 (upgrade) does not install Soundtrack Pro, sound effects etc..?

I just bought Logic Studio 9 (latest I suppose) upgrade version. Now I figured out that it does not allow me to install for example Soundtrack Pro, Sound Effects etc... How can I install them?
Logic Studio 8 was not installed prior to install because OS X Lion does not allow me to install logic studio 8.
What should I do now? Complete uninstall OS X and only update to OS X Leopard?

Hi
You have either moved the Applications or re-named them. For the updaters to work the Apps must be named "Logic Pro" and "MainStage.
CCT

Soundtrack Pro is Not Opening

I am having a problem opening Sound Track Pro. I am using version 1.1 (Final Cut Studio 1) and this is the second time I have had this problem. Double clicking on the program, it tries to open, then I get the message "Soundtrack Pro has unexpectedly quit." The last time this happened, I had some other problems too, so I just reinstalled the whole operating system. Nothing has gone wrong until now. I've tried logging on to a new "test" user account, but it is not my personal account (I did not log out however, but used fast user switching. I am a student participating in the Apple Insomnia Film Festival this weekend, so I need my computer fixed ASAP. Thanks in advanced to all

Hello. Sorry nobody responded sooner. Try right clicking on a small .aif file and selecting open with STP. Your problem might possibly be that whatever you were working on before became too large. Just a guess.
Hey, how did Insomnia go? I am competing as well. I can't wait till the voting begins on Oct. 19th. Do you know if there will be a link to the movies from the Insomnia home-page for voters? Hope you do well, What's your team name?

Sound not herd in Soundtrack Pro

Similar Messages

Maybe you are looking for