Sound not working on MacBook Pro

the other night my earphones were plugged in to my MacBook Pro and it dropped on the floor and wedged the jack inside. I eventually managed to get it out but now the sound doesn't work at all. Any ideas how I can fix this? And will it be expensive?
any help would be appreciated, thank you!

I hope it isn't expensive either! I got told the logic board would need to be replaced but wasn't sure if I was being ripped off; surely there would be a separate component off it for the 3.5mm jack...
I'm not an expert though, so I will just carry on looking around and get a few more opinions!
Thank you for the advice

Similar Messages

Why is my FaceTime sound not working in Macbook Pro?

why is FaceTime sound not working in my Macbook Pro?

how do i get my sound back on my Macbook pro?

Sound not working in MacBook Pro OS X

Hello,
I have a mid 2011 MacBook Pro. The silica gel packet in my backpack broke and it went inside my Mac's headphone jack. I tried to remove it with a tooth pic, knife, cotton swab, cotton swab with glue etc etc. And finally sound stopped working when the sillica gel went deep inside. The volume icon is grayed out since then.
At times I see a red light from the headphone jack. I understand that the speaker is ok, because I have a parallel installation of windows and the sound works fine in that! I also hear sound via external speakers and bluetooth headset in OS X. I took it to the Apple Store and they told me that I had to replace the entire motherboard which might cost around $550! I am not ready to do that! Everything else works just fine!
Anyone knows any fix for this problem? My MacBook is mute for a long time

how do i get my sound back on my Macbook pro?

Logic 8 sound not working on Macbook Pro

Hi has anyone else had problems with the sound not working on a MacBook pro.
Build in audio works fine but when I launch Logic all i get is a clicking sound.
MacBook is brand new.
Thanks

yer i did the latest updates and have it configured right too. when i open up a new project it works but when i open a full track i made in logi 7 it does have any sound and makes clicking noise.
i am wondering if its a UB update on one of my plug-in's? god its annonying aaaaaaarrr

Sound not working on Macbook Pro 13in" 4gbRam late 2009

My macbook pro started going crazy and then the sound stoped working can someone help me?

Try SMC and PRAM resets:
http://support.apple.com/kb/HT3964
http://support.apple.com/kb/HT1379
Ciao.

Youtube videos not working on macbook pro

youtube videos not working on macbook pro?

I just purchased a 13" Mid 2012 MB Pro, first time on YouTube, the videos would not play, google "Adobe Flash", download and install the player and you should be good.

Thunderbolt display not working on Macbook Pro - previously the display did work

Thunderbolt display not working on Macbook Pro - previously the display did work

I have upgraded ML but when the MBP tries to restart with the upgrade the MBP does not restart so I susapect the ML upgrade is not complete ? When you refer to 10.8.5 supplemental is this a separate upgrade ? When I connect the Thunderbolt to the MBP the Thunderbolt charges my MBP & I can play music from iTunes via the Thunderbolt. It is only the display that is not working on the Thunderbolt

Lightroom (CC) 2015 is not working with Macbook pro 2015 model ! any clues about it ??

lightroom (CC) 2015 is not working with Macbook pro 2015 model ! any clues about it ??

Ahmed
Generally signing out and signing in (signing out and back into the Creative Cloud application ) will fix this. If it isn't resolving the issue for you, let us know what you see and we can try something else.
Pattie

Sound quit working on MacBook Pro

sound quit working on macBook. have tried all PRAM/SMC resetting ideas. it seems that in SysPrefs/Sound/Output........"internal speakers" is no longer listed, and mute is checked. how can i re-add "internal speakers" as an output option?

There are many possible causes for this issue. Take each of the following steps that you haven't already tried. Some may not apply to your model. Back up all data before making any changes.
1. Start with the steps recommended in this support article. Don't skip any of the steps. It's the starting point for further efforts to solve the problem.
2. Run Software Update and make sure you have a fully up-to-date installation of OS X.
3. If you've installed an application called "Memory Clean" or any other third-party software that is supposed to "clean" or "purge" memory automatically, remove it according to the developer's instructions and restart. You should do that even if the software is not causing the problem, because it's useless.
4. Other third-party software that has been reported to interfere with sound output includes "Boom" and "Samsung Kies." If applicable, uninstall according to the developer's instructions (not by dragging something to the Trash.)
5. If an AirPlay device is selected for sound output from iTunes (or from other applications via third-party software such as "Airfoil"), deselect it.
6. Launch the application "Audio MIDI Setup" by entering the first few letters of its name in a Spotlight search and selecting it in the results (it should be at the top.) Select Built-in Output from the list on the left. If the Mute boxes are checked, uncheck them.
7. If a red light is visible in the audio-out port when sound should be playing, the internal switch is stuck in the position for digital output. You may be able to free it by inserting and removing a mini-stereo jack of the proper size. Inserting any kind of tool in the port may cause damage that won't be covered by your warranty.
If there's no red light, the switch may still be stuck in the headphone position. Try to free it the same way.
8. Disconnect all wired peripherals except keyboard and mouse, if applicable. If more than one display is connected, disconnect all extra ones. Restart and test.
9. If you have a MacBook Air, turn off Bluetooth and restart.
10. Start up in safe mode. Don't log in; just restart as usual when the login screen appears. When you do, make sure the words "Safe Boot" do not appear in the login screen. If they do, the system is still in safe mode and sound won't work.
11. Reset the NVRAM.
12. Reset the SMC.
13. Triple-click anywhere in the line below on this page to select it:
/Library/Preferences/Audio
Right-click or control-click the highlighted line and select
Services ▹ Reveal in Finder (or just Reveal)
from the contextual menu.* A folder should open with an item selected. Move the selected item to the Trash. You may be prompted for your administrator login password. Restart the computer and empty the Trash. Recreate your settings in the Sound preference pane.
*If you don't see the contextual menu item, copy the selected text to the Clipboard by pressing the key combination command-C. In the Finder, select
Go ▹ Go to Folder...
from the menu bar and paste into the box that opens by pressing command-V. You won't see what you pasted because a line break is included. Press return.
14. Reinstall OS X after backing up all data.
15. Make a "Genius" appointment at an Apple Store.

HT6337 sms forward not working on macbook pro

I am using an iPhone 5 running iOS 8.1and a macbook pro late 2011 model running OS X 10.10. I am able to call from my macbook pro but i am not able to send an sms. When i go to settings>messages>text message forwarding I can see my Macbook pro's name listed but when I enable it I don't receive any one-time code on my mac!

yer i did the latest updates and have it configured right too. when i open up a new project it works but when i open a full track i made in logi 7 it does have any sound and makes clicking noise.
i am wondering if its a UB update on one of my plug-in's? god its annonying aaaaaaarrr

Audio not working on macbook pro

Hi,
I have a 2007 Macbook pro. I have changed battery for this laptop twice in the past 5 years. As everyone else, I experience overheating issues. Otherwise, it has been working fine.
Today, I started using the itunes store to browse tv shows, books, and music. Suddenly I heard a big rattling noise (really loud) in my mac and it was coming from the top left side (probably the fan!). I quit the applications and shut down my laptop. When I restarted the mac, I could not listen to any songs neither from my mac nor from the internet, say youtube. No audio of any sort is working in my mac right now, not even the alert sounds.
- I checked the system preferences and could not change any output controls.
- After sometime, Ive also started noticing the red light in the headphone jack. But, this red light comes on intermittently. I tried putting my headphones in and out 3-5 times, it still did not solve the issue. The light may go off, but there is still no audio from my mac.
- Everytime I restart my mac, I hear the rattling sound. I checked my hardware, repaired the disk (using the Mac OSX disk), reset SMC, PRMV settings. None of these helped.
Im worried that my fan has gone bad and this in turn has also affected my internal audio system for some reason? I would appreciate any troubleshooting tips in this regard!
Thank you!

Well, for the red light issue, cut the end off a Q tip, or clean cut a Wooden tootooth pick(NO PAPAER CLIPS OR ANY OTHER CONDUCTIVE MATERIAL) and GENTLY "massage the headphone jack,(there is a micro switch that can hang, stop at the LEAST amount of resistance). Reboot see if that helps.
Also go to system preferences>sound>output tab and make sure the mute box is not checked, set the volume slider is at least half way up, and make sure built in speakers are selected.
If this does not solve your issue, go to utilities>Audio/MIDI set up, click putput tab, and make sure source is set to built in speakers, when selected double click on the built in speakers log out and reboot.
If you have been using Garageband, launch GB and go to GB preferences>Audio/MIDI, and select from the output tab intrenal speakers.
Here's what worked for me. It's not a workaround, this acutally solved the problem and I haven't had speaker issues since.
Go to "Activity Monitor" (you can hold "Command" "Shift" and press "U" if you're on the desktop).
Locate "coreaudiod" under "All Processes"
Right click it and click on "Quit"
After several seconds, "coreaudiod" will restart on it's own and your speakers will return to normal.
I tested this by restarting to see if it was a fluke workaround. Then I turned it off and waited a day (I had things to do so the waiting a day was easy lol). Turned it on, it was fine. I put it on sleep mode, waited 10 mins. and took it off of sleep mode. It was fine. Everything went back to normal for me.
Rattling sound is a concern for me as ths not normal, I would back up eveything, as this could br a HDD on the way out, and you want to save your data.
Also, you can try a a Pram reset:
If you have a removable battery, power doen your MBP, disconnected the power adapter, remone the battery, hold the power button down for 10 seconds, reinstall battery and mag safe and booy up.
If you have a MBP that has a non removable battery, follow the folling instructios.
Power off MBP, power it back on, holding the following keys: option, command,P,R, (no commas), press these key immediatly before the start up chime ringd, continue you to hold therse keys till you hear the start up chime ring ring 2 timess amd release.
Reboot
Since you had the battery replaced, you might want to try an SMC reset if non of the above offers any help. Power down MBP, power back up, hold the following keys before the star up chime. Left key shift,control, option, contine to hold these keys till the gear stops spinning.
Rebot.
All the best, I hoe this helps.
Let me know if this worked for you

Built in Audio not working in MacBook Pro after update to 10.7.3

The Built In Audio is not working in My MacBook Pro (Early 2011) after update to 10.7.3; I tried resetting the PRAM and SMC but it didn't helped me out. I can get audio only if i reboot my mac from Safe Mode or reboot after Repairing Disk Permissions in disk utility using the Recovery Partition;. If i make a normal restart or just startup then the built in audio disappers (audio is displayed gray in the menu bar) . Everything was working well with the 10.7.2
- Audio Works well with the Boot Camp Partition. and There is a sound during boot up.

I dont have any backups and i dont have time capsule or an external hard drive ready to be used for backup.
My macbook is my the only one computer. The problem is that the animation is lagging when i change the window to dashboard or safari or mail or another window. Inspite of this my macbook works well.
But 5 minutes ago, I noticed that if i run autocad on my mac- the lags go away!!!!

One earphone not working in Macbook pro

For some reason the audio output on my macbook pro is only working on one earphone. It is not the earphones as I have tried other earphones and the same thing happens. I had a problem recently with the output not working at all...and there was a red light coming out of the headphone jack. But the red light ended up going away on its own...and the sound came back. However...there is still only sound coming out of one earphone.

Hi again.
Nice website, except the wma files.
It is the right workflow to monitor what you mix before sending the material to the mastering studio. Although if you use Logic Pro 8 then you have compressor and can make this mastering by yourself (if you want to).
I try to say it easy: Without Light you can't paint, without suitable equipment you can't monitor an surround-mix. Only stereo is possible with your hardware. You can mix in surround in logic and listen in stereo. This is not optimal but the only chance to do this without buying an audio interface with minimum 6 outputs.

Internal mic not working on macbook pro

Hello,
A few days ago I was trying to use my macspeech dictate software on my new macbook pro for the first time, I had to plug in the mic it came with and it would not work. Now my internal mic will not work at all in any other programs. I made sure it was selected under system preferences but for some reason it does not pick up on any sounds. I have my computer all up to date with version 10.6.8. Does anyone know what the problem might be?
Thank you

I doubt that the update did it, My daughter Macbook has it too and it is a general update of Yosemite. But, if you can backup your files you could go to the restore partition and reinstall Yosemite. The reinstall only installs the operating system and usually does not alter any of the other files. But having a backup is always a good idea. You can start by holding down Option or Option R at startup to do the reinstall.I cannot tell you that this will fix the internal mic problem as it could be that it is defective.

Old MagSafe Airline Adapter not working with MacBook Pro Retina

I've got an old MagSafe Airline Adapter (one I bought when it first came out) that I'm trying to use with my MacBook Pro Retina (using a MagSafe to MagSafe 2 Converter). Sometimes the light is green, sometimes it is off, sometimes the battery icon in the menu bar shows plugged in, sometimes not, but in any combination, the machine is not maintaining charge; the battery discharges at a normal rate for just being on battery. For giggles, I borrowed my seatmate's year-or-two-old MagSafe adapter (the one with the right-angle plug) and plugged it into my machine (also using the MagSafe to MagSafe 2 converter). The light on that one turns orange, and though the battery icon shows "Not Charging", the battery is maintaining charge with the newer adapter. (My adapter, BTW, is able to maintain the charge on her 13" MacBook Pro.)
Was there a change to recent versions of this adapter to make the new ones work with the Retina MacBooks where the old one will not?

the green light on the mag safe turns on?
you should reduce your usage to a very minimal amount as I'm sure the airline doesn't output a strong enough signal for you to be running full screen films with high res. Maybe you should close your macbook P and see if it is charged after a little while of not using it.
turn your screen lights down, turn the sound gHZ down, quit all the downloadin'.
if you must run flash make sure you have the latest version (from the adobe site).
You're computer is intense and if you use it more then it's gaining, of course it going to be draining .
But this is probably moot since you're probably on said plane now. or was.
I'd imagine if you're not satisfied with the product you should return it detailing your situation.

Sound not working on MacBook Pro

Similar Messages

Maybe you are looking for