Sound on itouch fades in n out, also jack only plays on ear bud?

Sound on itouch fades in n out and earplugs (good ones) only play on one side. THX.

Sounds like the jack is bad and may need to be replaced.
Dave M.
MacOSG Founder/Ambassador  An Apple User Group  iTunes: MacOSG Podcast
Macsimum News Associate Editor  Creator of 'Mac611 - Mobile Mac Support'

Similar Messages

Audio out jack only plays sound in the right speaker.

Whenever I plug anything (speakers, earphones, etc.) into the Audio Output jack, it only plays sound through the right speaker/earphone. The left speaker/earphone hardly has any sound at all.
How should I go about fixing this problem?
It ***** and it's annoying. At first, I thought it was just my earphones but they work perfectly fine with my iPod and other devices.

HI Chris,
my daughter has the ipod touch 4th generation and it started only having sound come out of the right speakers in both of my vehicles. I read also it could be a broken socket causing it. Do you know about this? How does one break a socket and how would I repair that? The person on y*hoo answers said to either send it to apple refurbished unit or replace it. Replace it? Really? It's a 64 GB ipod touch that I won at work with reward points which is the only reason I could afford it. Looking for better solution like your's above but I'm worried I will have to send it in. I was looking on my iphone 4 and noticed the volume balance was under Settings>General>Accessibility so I guess it's different on an ipod touch?

IPhone sound jack, only hear one ear

iPhone 4, OS 5.1.1 only hear sound from one ear bud, had headphone jack replaced same problem. was recommended to back up and restore and see if that works. Any thoughts?

Ok, but make sure you push down firmly. Sometimes the last "bump" is a little hard to get over when inserting your earphones. If you're sure it is, you may want to try another pair of earphones/headphones to make sure it's the phone that's the problem. Otherwise, you can try restoring your phone, first using your backup. If that fails you'll have to save as much of your data as possible and restore it as a new phone, without using your backup. If the problem remains after restoring as a new phone then you'll have to make an appointment to take it to the Apple store for evaluation as it may be a hardware problem. Be sure to back it up first in case it has to be replaced.

I put my samsung headphones in all the way and there's no treble and sound is muffled, halfway in and sound is fine but headphones fall out of jack.

They are the stock headphones that came with my Samsung Galaxy S.

Also when I plug in my Samsung headphones there is 3 stages of volume:
1, when the jack is completely out and the iPod is in speaker mode, the volume automatically gets set to zero.
2, I have them half-in and they work normally, and I keep at 50% volume, but fall out if I don't hold it in
And 3, when I push it completely in and the volume changes for a third time, to another volume value..

Headphone jack only plays out 1 headphone (Right side)

Really need help, im a DJ and use this laptop for it!!
My headphones only have sound coming from 1 side, ive tried reinstalling drivers etc and everything else ive read online.
I need this resolved ASAP so any help is appreciated.
Thanks

Hi @chadhogan121
Welcome to the HP Support Community! I saw your post regarding the problems with sound only coming out on one side of the headphones. I will be happy to help you with that. Have you tried a different set of headphones to see if the same thing happens? This HP document No Sound from Speaker will show you how to use the built-in Windows troubleshooter. Give that a try.
Please click “Accept as Solution ” if you feel my post solved your issue.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Thank you,
BHK6
I work on behalf of HP

5g ipod nano 8GB no sound through ear buds or headphone jack only when docked.

5g ipod nano 8GB no sound through ear buds or headphone jack only when docked. any suggestions? i don't want to replace any of the parts inside if at all possible.
I have a 5th generation 8GB iPod nano. I bout it off of eBay in May of 2010 and it has worked great until now (Apr 2011). The 5th gen plays music through the headphone jack even when no ear buds are plugged in. I was using it one day and it just stopped. I tried resetting it manually and automatically and I tried reinstalling iTunes. Nothing has worked. Now it won't even play sound though the ear buds (or the aux hook up in my car), only when it is docked to my iHome. Does anyone have any suggestions? I dont want to replace the iPod or any parts inside if at all possible. ANY SUGGESTIONS ARE WELCOMED! THANKS!

Headphone jacks are only good for so many in and out usages. Usually its the headphone jack itsefl that goes bad first but sometimes it is the internal part. If you are lucky you can clean out the inside and get it to work.
These devices are not made to last for someone who actually has those headphones around there neck and acually uses there listening devices through out the day plugging it in and out. This is not in any way an Apple thing, it is a problem with many devices. The male ends tend to get dirty hanging around then scratch the female end when used. In fact, using higher end headphones you can really notice even the smallest particles of dust on the male end of plug when used, that is the small popping you might notice when the cord moves.
Hopefully its a problem on the male side of things.
I would recommend a person that wants to use headphones alot to keep a small 2 inch extension plugged into there device that can be replaced when it goes bad inplace of wearing out the original plug.
Again, this is not an Apple problem alone.

I have adobe Premiere Elements 13. It will not let me delete audio or have it fade in or out. I can move the yellow line all the way down till the volume reads -0.0, but the sound is still there on playback. I can click on fade in and fade out and the yel

I have adobe Premiere Elements 13. It will not let me delete audio or have it fade in or out. I can move the yellow line all the way down till the volume reads -0.0, but the sound is still there on playback. I can click on fade in and fade out and the yellow line that graphs volume takes a sharp raise or dip at the beginning or end of the clip, but there is no change in volume when I play back. What am I doing wrong?

rickeyt
Thanks for the reply. Great news about the volume adjusts.
Now about those fades for the volume. How are you doing that?
1. Right click the Timeline video audio and select Fade and then
see the Fade options (I had a video with audio file, so I saw the choices as shown in the screenshot)
2. You can also create two volume keyframes at each end of the Timeline audio clip rubberband (orange line that goes horizontally across the middle of the audio clip). At the position of the Timeline Indicator, click the Add/Remove Keyframe icon, and then with the mouse cursor position the white dots (volume keyframes) to achieve the Fade In and Fade Out audio. In the screenshot below I have moved the Timeline Indicator so that you could better see the white dots (volume keyframes).
Please let us know if any of the above works for you with regard to the audio fades.
Thank you.
ATR

When I play itunes from my laptop which uses a Y-cord plugged into a sound board, the songs fade in and out, softer/louder ...anyone know what would cause this? I have bought new cords, speaker cords, speakers...and the laptop is only 1 year old...

when I play itunes from my laptop which uses a Y-cord plugged into a sound board, the songs fade in and out, softer/louder ...anyone know what would cause this? I have bought new cords, speaker cords, speakers...and the laptop is only 1 year old...

when I play itunes from my laptop which uses a Y-cord plugged into a sound board, the songs fade in and out, softer/louder ...anyone know what would cause this? I have bought new cords, speaker cords, speakers...and the laptop is only 1 year old...

IPhone 5 voice call quality fade in and out. Noise Cancellation interference?

I've been having this huge problem with the iPhone5. The evidence i've collected seems to indicate this is a problem with all iPhone5's.
On calls in certain places both indoors and outdoors, the callers voices over the iPhone5 fade in and out. Their voices occasionally completely fade completely away, and only come back momentarily. The low volume for 50% of the time forces me to raise the volume, but raising the volume does not help because when the voice does come back, the volume is too loud for my ears.
I went back to the Apple store and they are not able to help me. They suggested a clean restore, which I did. They offered to replace the phone, which I did, but it is the same problem.
- iPhone 5 vs. iPhone 4S, the fading does not occur. I make the call to the same voice mail system I have, and the sounds from the other side are consistently the same volume for the 4S, but fades in and out for the 5.
- I connected up a 8mm jack between my iPhone 5 and my mac in an attempt to record this problem. In that instance, the sounds from the voice mail DO NOT fade in and out. I did find out that the dynamic range on the iPhone 5 is MUCH greater than that of the iPhone 4S, for some strange reason.
- When I hold the phone up to my ear, the fading in and out does occur, but it is less noticeable. But it's still there.
- When I leave my work area the problem goes away. However, because the iPhone 4S on the same AT&T service does not have this problem, this leads me to believe it's NOT a lack of transmission power from the AT&T cell tower. Rather, it is a reception issue at the iPhone5 side.
- I turned off LTE, data and then made the calls. Same issue.
I use this phone to make 60 minute calls for conference calls frequently. I cannot use it. Please advise. I am seriously considering returning this phone. Except i've sold my old iPhone 4 already. I'm in a bad place. Please help.
Here's another post of a fellow with the same exact problem.
http://forums.macrumors.com/showthread.php?t=1456404
Apple, please look into this. I believe this is a problem with the noise cancellation software.

I've got an update on this problem with fading volume. I've isolated it to the set volume on the phone for voice calls when using headphones. When the headphone volume is set between 1 and 6 (out of 16 squares) the callers volume will consistently fade in and out. The fading which is normal to zero volume at 2-5 Hz is serious enough that normal conversation is impossible. When the volume is raised above 6/16 then the callers voice stabilize and I can hear all their words again. Unfortunately, at 6/16 volume their voices are too loud for the headphones.
Furthermore, when headphones are plugged in, and I initial a call after the iphone5 was idle for several minutes, the first dial tone has preceded by a very loud pop an the tone, as though there was too much pressure (charge) that was dissipated all at once.
Other details:
- I used 3 different earphones, iPhone 4 headphones, altec earphones, an the new iPhone 5 earbuds. Same.
- I turned on and off lte, data, Bluetooth, wifi. Problem persists unaffected.
- when switching to iPhones earpiece and mic, the fading is gone.
- I have 3 out of 5 bars where I teste this, in the city outside and on hwy 5 in central California. Same symptoms in all places I've tested.
- I have exchanged my phone at the apple store. Same issue with both iPhones an I suspect all ipjone5s.
- the ipjone4s does NOT have this problem when the volume is set lower. I can tell that the iPhone 5 must have a new audio filter to make the sounds have larger dynamic range. I liked the 4s better, because it is easier on the ears!

I have used I tunes to download music with a paid I tunes card. I can no longer open the music store to download my music. When I do open the music store it fades in and out, preventing me from downloading music.

I can nolonge download music from I tunes, because the music store page fades in and out and will not remain permanent to allow me to download music with a pre-paid I tunes card.
Also, why is it you can only download music to an I-pod from one primary computer. Is there a method that will allow me to download music from a variety of computers.

it only happens for previous purchases - if you have a computer you can try to download your purchase history there and then just sync them to your device - http://support.apple.com/kb/ht2519 - http://support.apple.com/kb/ht1386.

I placed my ipad on top of my CPU with a music playing,i heard a crack on the sound and when i checked it,i can no longer hear a sound playing on my ipad.i tried to check place a headphone its still playing a sound but when i pull it out,wont play at all.

i placed my ipad on top of my CPU with a music playing,i heard a crack on the sound and when i checked it,i can no longer hear a sound playing on my ipad.i tried to check place a headphone its still playing a sound but when i pull it out,wont play at all.

I don't know if this will work but it's worth a try. I wonder if somehow you ended up with a short inside of your iPad. Give the things below are trying to see if that helps. Good luck.
Try a Restart.
Press and hold the Sleep/Wake button for a few seconds until the red "slide to power off" slider appears, and then slide the slider. Press and hold the Sleep/Wake button until the Apple logo appears.
Resetting your settings
You can also try resetting all settings. Settings>General>Reset>Reset All Settings. You will have to enter all of your device settings again.... All of the settings in the settings app will have to be re-entered. You won't lose any data, but it takes time to enter all of the settings again.
Resetting your device
Press and hold the Sleep/Wake button and the Home button together for at least ten seconds, until the Apple logo appears. Apple recommends this only if you are unable to restart it.
Or if this doesn't work and nobody else on the blog doesn't have a better idea you can contact Apple.
Here is a link to their contacts with most of the information below.
http://www.apple.com/contact/

The sound on my iPhone 4S cuts out when playing music/podcasts.

The sound on my iPhone 4S cuts out when playing music/podcasts. If I unplug and replug in the headphones, the sound comes back on, but often for only 20 seconds or so before cutting out again. Sometimes it will play for 15-20minutes before cutting out. The track is not "paused", and appears to continue, just no sound. I tried cleaning the headphone jack with compressed air to no avail. I also noticed the the same phenomenon occurs when I sync my bluetooth to my car audio. That is, it will play for a while, then the sound will cut out, even though the track is still shown to be playing. If I reset the bluetooth, the sound comes back on.
This started happening about a week ago, but no "event" that I can think of caused it. I didnt' get the phone wet, forcefully drop it, or leave it in extreme heat. I've tried doing a reset of the phone. I also was running iOS5 when I first noticed this, and since upgraded to iOS6. The problem appeared with both.
Any help would be greatly appreciated.
Thanks,
Steve

One thing that helped was getting a toothbrush and scrubbing the dock connector on the phone. I scrubbed the connector and used compressed air for about 1/2 hour till the connector looked much cleaner. An Apple employee told me that the pins on the phone had a little corrosion and sand. The problem hasn't gone away completely, but has been significantly reduced. I'm going to hold out until my contract expires after which time I'll switch to an iPhone5 (or newer) or Android phone.

How do I Fade in and out, working with Midi events?

I'm new to logic.
How do you set certain virtual instruments(midi events) to fade in or out. I have a string arrangement written, and whenever the strings end it is very abrupt and unnatural. I want them to fade out, as opposed to just cutting like they do. I would also like to know how to fade in. Is it the same process?
Please help me out if you know how to do this.
Thanks...

I'm not sure what you mean about fading the instrument and not the notes. I just want to fade out one note/per instrument at the end of certain passages. Care to expound?
In general, MIDI does not provide a mechanism to control the volume of individual notes.
In MIDI (and sequencer terms), a note has a note on, a note number (which key was pressed) and how hard you hit that key (velocity). Then a corresponding note off. There is nothing in a note specification that let's you control the volume of a note through it's duration.
In MIDI terms, you can use a controller MIDI message, typically #7 which is used for volume, and modify that over the time the note is playing. But this is controlling the volume of the instrument not the individual notes - the same as turning up and down the volume on the instrument. All notes that the instrument is playing are affected equally - if you are holding a chord, the entire chord will ramp in volume. You cannot just ramp the volume of one note within the chord using this method.
(The closest MIDI can get to controlling individual notes volume is with polyphonic aftertouch, but this is not often supported and is a more advanced technique - given that you are new to this I'm going to ignore it for now to avoid over-complicating things. I mention it to stop all the people chiming in with "you're so wrong Beejay you muppet you can do this with poly aftertouch don't you know anything" blah blah).
Is that more clear?
Also, if you wouldn't mind, could you give me a step by step on opening the hyperview in the piano roll?
Open the piano roll, select View -> Hyperdraw -> Volume.
You can click/draw in it with the pencil tool to create MIDI volume (CC#7) changes.

How do I fade in or out music, because i want to put in muiltible song in one clip? can anyone help????

i want to fade in or out music to put heaps of music inb one clip please help

I'm not sure what you mean about fading the instrument and not the notes. I just want to fade out one note/per instrument at the end of certain passages. Care to expound?
In general, MIDI does not provide a mechanism to control the volume of individual notes.
In MIDI (and sequencer terms), a note has a note on, a note number (which key was pressed) and how hard you hit that key (velocity). Then a corresponding note off. There is nothing in a note specification that let's you control the volume of a note through it's duration.
In MIDI terms, you can use a controller MIDI message, typically #7 which is used for volume, and modify that over the time the note is playing. But this is controlling the volume of the instrument not the individual notes - the same as turning up and down the volume on the instrument. All notes that the instrument is playing are affected equally - if you are holding a chord, the entire chord will ramp in volume. You cannot just ramp the volume of one note within the chord using this method.
(The closest MIDI can get to controlling individual notes volume is with polyphonic aftertouch, but this is not often supported and is a more advanced technique - given that you are new to this I'm going to ignore it for now to avoid over-complicating things. I mention it to stop all the people chiming in with "you're so wrong Beejay you muppet you can do this with poly aftertouch don't you know anything" blah blah).
Is that more clear?
Also, if you wouldn't mind, could you give me a step by step on opening the hyperview in the piano roll?
Open the piano roll, select View -> Hyperdraw -> Volume.
You can click/draw in it with the pencil tool to create MIDI volume (CC#7) changes.

It sounds stupid but I cannot figure out how to create a TOC

It sounds stupid but I cannot figure out how to create a TOC

You'll find some good video tutorials with these Google searches:
(search Google for these terms without quotes)
* indesign paragraph styles tutorial
* indesign table of contents tutorial
* InDesign paragraph styles in table of contents tutorial
The simple principle is: InDesign creates a TOC by "pulling out" heading paragraphs from your document. To help it know which paragraphs are the headings you want in the TOC, you need to create paragraph styles, and apply them to the heading paragraphs. Then, when you perform Layout > Table of Contents, you choose the heading paragraph styles, and run the process.
It may be daunting if you've never done anything like this. But, if you've done it in MS Word or other word processor, the principle is the same - make the headings identifiable in some way, so the software can extract them.
Look at the video tutorials, create a heading paragraph style, create a TOC, and let us know the result.
If your document is one of several that are gathered into an InDesign book, search Google for terms like "working with InDesign books tutorial," and "InDesign book table of contents tutorial," without quotes.
It would help if you can provide screen shots of your result. Search Google for terms like "how to create a screen shot on mac," or "how to create a screen sot on windows," without quotes. It also helps to display hidden characters when you make the screen shots. Search Google for terms like "how to display InDesign hidden characters," without quotes. Search Google for terms like "how to post a screen shot on an adobe user forum," without quotes.
HTH
Regards,
Peter
Peter Gold
KnowHow ProServices

Sound on itouch fades in n out, also jack only plays on ear bud?

Similar Messages

Maybe you are looking for