Sound system

I have a problem with my sound system which i have tried to update my notebook's components but it still does not produce good sound. The problem with my notebook is that when ever there is a sound i hear the sound breaking off and on. I plead on your behalve to help me figure out the problem with my notebook and a solution to it. Thanks

Hello Dasana. In order to assist you, I need you to answer a few questions:
What computer model do you have? If you need assistance locating that, you can refer to this document: http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&docname=c00033108
What operating system do you have?
What is the model number of the sound system?
Has it worked perfectly before?
Please respond as soon as possible. I'm only here to help!
Mario
I worked on behalf of HP.

Similar Messages

My sound system does not work AFTER installing pc to tv wireless connection

my sound system does not work after installing hp pc to tv wireles device when I am using lap top for other purposes.

Hi,
You don’t install VS2010 on the client PC, then where did the Form Invoice not work? When you run it from another version of VS? Or when you run the application with application.exe?
Based on your description, one form works well, another form does not. I assume that two forms are in two different projects, then please check the .Net Framework used by the two projects. If they are different, you can use the
one used by the Form contact for Form Invoice.
Because this issue is a project issue, I recommend you to consult it on some application forum such as Windows Forms General forum for better support.
VS General Question forum mainly discusses
the usage of Visual Studio IDE such as
WPF & SL designer, Visual Studio Guidance Automation Toolkit, Developer Documentation and Help
System and Visual Studio Editor.
Thanks,
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

How to connect a apple tv to a panasonic sa-pt860 home theater sound system?

how do i connect my apple tv to a panasonic sa-pt860 home theater sound system? Having no luck, what leads do I need please?

Welcome to the Apple Community.
Does it have HDMI inputs and outputs.

Apple TV...how to connect to get sound through my sound system (I have a satellite receiver and also Russound system)

Just hooked up my Apple TV. It's great. I have a satellite receiver and also a multi room sound system where I would like the sound to come through. Can anyone tell me how I would connect to accomplish this. My HDMI is connected so the sound is coming through my TV just fine. I would like it to come through my sound system instead. Your assistance is very much appreciated.

goaliemother wrote:
Hi:
My system is as follows. 1 only HDMI output on TV. I purchased an HDMI switch box/unit. I have the output from the Switch Box Unit going into my TV.
I have 5 inputs on the switch box unit. 2 I have used.....
1 input from my television satellite receiver
2 input from my Apple TV
My other equipment is
1 home theatre system. This is where the sound from my TV goes through
1 russ sound whole home sound distribution system
When I play my Apple TV I am still getting the sound of my satellite TV.
This suggests that your satellite receiver is connected to your "home theater system" (which I will shorten to AVR "Audio/Video Receiver") for audio. Is this correct?
If so, then your problem is that you're switching video inputs, but not audio, and what I listed as (2) applies:
2. You can connect the ATV to the TV using HDMI. Then you can either:
2a. Connect the TV to the AVR using an optical cable for audio.
2b. Connect the ATV to the AVR using an optical cable for audio.
You've connected the ATV to the "switch box" instead of the TV, which amounts to the same thing, as you're just expanding the number of HDMI ports on the TV by using the switch. So your simplest solution is either 2a or 2b. If your TV has an audio out port, and it's the same kind of port that your satellite receiver uses, you can just disconnect the audio cable from the satellite receiver and plug it into your TV. You may have to enable "external speakers" or whatever they call it in the TV settings. This would be best, because then you wouldn't have to change inputs on the AVR to select the correct audio; you would just change inputs on the switch, and both video and audio would switch between the satellite box and the ATV, solving your problem. Note that an optical cable is required to get Dolby Digital 5.1 audio (surround sound), and I mention that because it's possible you're using an analog audio (RCA) cable. So an optical cable is best.
Beyond this, I would really need to know your TV and AVR model numbers, preferably accompanied by links to specification pages or manuals, and it would be very helpful to know how the satellite receiver is connected to the AVR for sound.

Itunes won't play anymore through external sound system

My mac functions as a Protools recording studio. The hardware (a Digi002 system) attaches to my G5 by firewire. Until recently, itunes worked just fine playing through this external system. I'd simply go to system preferences, change the sound inputs and outputs to Digi002.
These days I can still get all of my pro music software to play through this external Digi002 system. But something has gone amiss with itunes. It doesn't matter if itunes is already open, or not yet open. If I go to sound preferences and switch it to DIGI002, itunes ONLY plays through my internal compouter speaker. And if i go back to the sound preferences, i find that the external audio choice had been unchecked, as if by some function within itunes itself.
i have asked this same question on the Protools forum. Respondees give mixed answers, but basically say, yes it used to work, and no, it no longer works. Some say it WILL work, but you have to fire up your sound system BEFORE you turn on your computer. That is a totally disfunctional "solution" for my situation. Who wants to keep a sound system on all day long, when I may not use it for several hours at a time?
So what's going on here? And what did I install that made itunes suddenly not function with my external system? I strongly suspect it may be some newer version of itunes itself. If so, is there some workaround utility that will let me re-connect itunes to the Digi system? any help is appreciated.

Hate to do this, but we've gotta start with the simple **** first, and work our way up. The volume control in iTunes isn't turned down, is it?
Aside from that, you should launch Quicktime Player, go to File - Open, and open one of your iTunes songs in that, and see if you can hear sound there.

How do I connect the ipod nono 7th gen. to Panasonic home theater sound system

I ordered an ipod nano for my daughter for christmas as her old original ipod died. She has a Panasonic home theater sound system (SA-PT950) that came with a little dedicated ipod station to connect her ipod to and get surround sound music. Now I see the 7th gen. nano has a different interface and won't work in this station. Is there an adapter available or does anyone know another way to connect it? Thanks

http://store.apple.com/us/product/MD823ZM/A/lightning-to-30-pin-adapter?fnode=72

HT4587 Hi, I want to set up a sound system in a new house using apple equipment. I have few sets of Bose speakers that I would like to utilise, my question is - what do I need to set it up and how do I do it with regards to AirPlay? Thanks

Hi, new to the forums and apple tbh.
Moving into a new house and want to set up a sound system, thought apple would be the way to go as I have iPads, iPhones, iPod touch and nanos. I also have a few sets of Bose speakers which I would like to incorporate. What I am wondering is, what else do I need to buy to do this? Do I need seperate devices to attach to each speaker? Do I need a new router? And how would I configure it?
Ideally I would like 4 rooms each with their own speakers that could play simultaneously.
Thanks in advance!!!!

First, please check out the following Apple Support article for details on setting up an AirPort Express Base Station (AX) for iTunes streaming. Note: You will need a separate AX for each set of speakers that you want to stream to. Also, note that you can stream a single audio file to one or more speakers, but you cannot stream separate audio files to different speakers simultaneously.
Second, the Bose speakers you mentioned would need to have an audio input jack, either analog or optical digital to receive the stream from the AX. As you know, Bose makes a number of different speaker/home theatre audio options. If your specific model of speakers do, then it's just a matter to use the appropriate audio cable between the audio port of the AX and the speakers.

A black airplay info window floats around on my HDTV screen when sending audio content via airplay up to sound system w Apple TV. How can I get rid of this?

A black airplay info window floats around on my HDTV screen when sending audio content via airplay up to sound system w Apple TV. How can I get rid of this?

Had this happen to me after a recent update, was super annoying. To turn off, go to Settings > AirPlay > Conference Room Display > Off.

Is there a way to adjust the bass and treble on my iMac Power PC sound system?

Is there a way to adjust the bass and treble on my iMac Power PC G5 sound system? It has a lot of volume (more than my JBL speakers).

No, but iTunes has an Equaliser that enables you to do that.

I have a ipod nano, and I bought a Bose portable sound system, when I put my ipod in the unit and play my songs in shuffle mode, it plays the same song over and over, how do I get it to play in shuffle mode?

I have a ipod nano, and I purchased a Bose portable sound system to play my ipod on
but it will not shuffle the music, it will play the same song over and over, until I hit the
next song on the remote or do it manually. Does anybody have a solution?????

Sounds like the repeat setting has been enabled. See your iPod's User Guide for information on how to turn it off.
http://manuals.info.apple.com/en_US/iPod_nano_6thgen_User_Guide.pdf
B-rock

Beats-Audio / Sound System Enhancement dv7 / HP Envy 15

Beats-Audio - Sound system Enhancement
Test system
dv7t – 6100 Quad / Windows 7- 64bit
Beats-audio
Introduction - Cave Sound Caper
Edits 29-Nov-2011
This is a re-write of this document.
Parts One and Two have been flipped. It's a work in progress.
The purpose of this Post is to provide a method to enhance the sound coming from your onboard beats-audio speakers. The quality of the sound should improve - more importantly, MORE sound should be available. This is important if your system is suffering from lack of enough sound from the onboard speaker system.
This process does not make use of the Loudness Equalization enhancement. I tested the Loudness Equalization enhancement (for a different purpose). Setting the enhancement on my test system and then switching the enhancement off resulted in the “Low Sound” syndrome. It took some amount of work to recover from that mess. The Loudness Equalization enhancement, in this author's opinion, is to be avoided unless its use is necessary.
FLIPPED:
The original intent of this procedure has been to provide a means to increase the amount of sound available from the onboard speakers on notebooks that are equipped with beats-audio IDT sound drivers. The “Pre-work” on my original post was overwhelming the intent. If your system is healthy, and the only reason to read this document is to enhance the amount of sound from the speakers, there is no need to hash through the work to fix your IDT driver installation. I’ve moved that section to the end – IDT installation and other work has become Part Two.
You must have your IDT HD driver successfully installed into your system.   The proper IDT HD driver contains the beats-audio interface.
Where to Start?
If you have “No Sound”, the Enhancement process may not work for your system. Please take a look at Part Two and decide whether any of the steps in that section apply to you. It is not my intention that you waste your time trying things you’ve already done over and over to regain the sound on your system. There are many posts on the forum on how fix “No sound”. This post addresses only a couple of “No sound” issues.   There is one slight possibility – see the section about the controls in iTunes – make sure your sound players volume controls are not mis-matched – and make sure you didn’t turn something OFF by accident. If you turned off the sound while watching a movie and now the HDMI sound is off - Poof! You might not have any sound – anywhere. It's just something to check...
If you have “Low Sound”, you might consider reinstalling your IDT driver to see if the issue can be corrected: IDT reinstallation is described in Part Two.
SideBar: As of 24-Nov-2011
If you have a dv7t: check on your HP Software and Driver website for a new IDT HD audio driver. Depending on your model, there may be a new version of the IDT driver, BIOS, and other important updates.
Part One
Some Setup Checks and on to the Enhancement
Make sure all basic Sound settings are set to “Default” to start.
Portions of this procedure are "not of my invention". Full credit will be given later in the Post. This section explains how to increase the amount of sound coming from the onboard speakers. It also attempts to give you a bit of control over the kind of sound coming from the speakers that you may not have at the present. Beats-audio is great; frankly, though - it's made for external powered speakers or headphones... what you get from the speakers on the notebook leaves something to be desired.
A while back I found a very interesting post on the topic of increasing the sound from the onboard speakers. The post was originally written for the HP Envy15. I believe the post has merit - Part One of this procedure is based on that original post.
I tested the suggested combined actions – it does work (at least on a healthy system). The sound quality showed improvement over the standard “out-of-the-box” beats-audio setup and the quantity of volume increased. In other words, this procedure makes the sound coming from the onboard speakers louder without the use of the Loudness Equalization enhancement setting.
I would suggest trying this “Enhancement” under the following circumstances:
Sound Quality is Poor, or the amount of sound from the speakers needs improvement
Sound is quantity “LOW”*
Sound is absent AND you believe the absence is NOT due to hardware failure.** See note on iTunes.
NOTES:
* If your LOW sound issue is severe, it may ONLY respond to using the Loudness Equalization enhancement, in which case this procedure is not recommended for your use. The two are not compatible. See Part Two.
** If there is NO sound on your computer, it’s possible that completing this procedure may not result in any improvement. See Part Two.
Sound Controls – iTunes, Media Player
I would add to the emphasis on checking the volume on one’s iTunes setting. If iTunes volume is turned down, the notebook’s speakers will respond to that – turn up the volume in iTunes without adjusting the volume in the volume mixer and the sound on the notebook will not increase properly (or will suddenly jump). It’s a juggling act and one that must be taken into account when the sound is being reset.   Additionally, if you have other audio players on your computer – in addition to those mentioned in the post – be sure to check them for volume controls: it is important during a sound reset that all the sound players be in sync. If you miss this, you may not get your sound back.
Check for this mismatch in sound volume controls if you do not have sound or if you did have sound and, at some point you turned OFF your sound while watching a moving, a DVD, a something on HDMI controlled audio - and suddenly - you do not have any sound. Sound controls get tangled up. Sometimes you just have to unplug it, but you do have to check the controls.
Sample Rate and bit Depth
I do not use the suggested Sample Rate and bit depth of 24bit 96000 Hz. My system cannot tell the difference and defaults everything to 16bits – my recording equipment cannot discern the difference.   My ears lack sample rate sophistication.   I’ve left my dv7t Quad sound, Default Format (sample rate bit depth) at 16bit, 48000 Hz (DVD Quality). Sounds fine and it’s where most of my crummy recordings are set anyway. Don’t lose sleep over this one.
Where’s my Taskbar ICON?
A couple of HP forum posts have mentioned the loss of the beats audio icon from the Taskbar tray – the icon should restore itself if one can force the IDT driver to reinstall. Without the IDT driver, beats-audio is not going to work. Assuming the driver has installed and one can reach the beats-audio panel from the Control Panel, THEN it’s possible that for some weird reason the Taskbar icon didn’t reset. It might be possible to try and force a reload of the beats panel controller into the Taskbar. I think this is the file.
For a 64bit system:     C:\Program Files\IDT\WDM\sttray64.exe
The Original Post and Credits:
The original procedure and excerpts from that Post follow. Edits have been made to make it easy to read and to follow. The credits and original link are at the bottom of this page. My thanks go to JJ and JJ’s HP Envy15.
From the Original Post:
Originally Posted by bigcat400
I find the volume on this machine extremely low. Unless the room is totally quiet I can't hear a thing. Is this normal on this system, or could it be a driver issue? I am running the latest sound driver from HP's web site.
From JJ:
It took me awhile but I now have the sound level about 3x what it was to start with. Try these tweaks:
Sound Enhancement Procedure
Control Panel > Sound > Playback > (Highlight) Speakers and Headphones > Configure
New Window ‘speaker setup’ > Test (should hear sound L/R) > Next >
           UNCHECK ‘Front left and right’ (if checked) > Next > Finish
Sound > Playback > (Highlight) Speakers and Headphones > Properties >
            Enhancements > bass boost > settings > 80 Hz / boost 3db > Apply
             Tone Controls > Bass +1 Treble +3 > Apply
             Advanced > Default Format > 24 bit 96000Hz > Apply
NOTE:
After this DO NOT use the Beats control (Fn + B) or it will reset the tone controls.
HP dv7(t)
Taskbar > beats-audio panel
OR
Control Panel > Beats Audio Control Panel
        Listening Experience > Graphic Equalizer > Custom
        -1, +8, +10, +8, +9, +9, +9, +8, +9
Remember that these are suggestions – start here and re-adjust later as desired.
LEFT SIDE
Make sure Beats Audio is CHECKED
        Click the “Music” radio (round) button
        65, 65, 85, 65, 65
NOTE: The Left Side settings are somewhat arbitrary. The “Center” setting is higher – this provides the most sound and should be set higher at least initially for testing, especially if your system has sound issues.
The next section is partially excerpted from the original Post – Remember: JJ’s post was written for HP Envy15 – please adjust your results accordingly. Edits have been made for readability.
Control Panel > Beats Audio Control Panel
Playback > Speakers and headphones > Arrow above Speaker symbol and Select Small Speakers
Select Equalization> Select 'custom'>
Adjustments for this are mainly to boost the signal level in the preamp so we get higher volume while not distorting the sound from the tiny built in speakers.
My setting values are as follows: left to right;
-1, +8, +10, +8, +9, +9, +9, +8, +9, +10
MAKE SURE TO CLICK SAVE WHEN DONE!
Note: Do not crank up the Bass (31hz) control or it will overload the speakers which can't reproduce this anyway, you can even turn down more if you have distortion at high volume.
Check that the slide controls for 'master' and 'speaker symbol' are all the way up.
This should make a big difference in sound volume and quality, and there is one last way to get louder sound. Depending on what you use to play back your audio you can adjust the program’s sound settings or EQ controls also.
In iTunes the EQ has a 'preamp' slider which I boost to about +6, this increases the output level while leaving the EQ settings alone (make sure to check the turn EQ on box).
Windows media player: you have to raise all EQ levels equally (not too much) to boost without affecting sound quality.
In general it is not a good idea to use more than one EQ system in an audio signal or you get more distortion, so don't adjust the EQ curves or bass/treble on more than one device. I chose the Beats / IDT EQ to make the tonal adjustments because it is the audio driver program and preamp that outputs to the speakers, so it should have the best sound quality.
Any adjustments before the preamp that add distortion will just be amplified, so go easy on adjustments in your play back programs.
Finally, when you play your audio,
Sound > Open Volume Mixer >
Make sure to click the Sound logo in the Taskbar so the slider pops up>
Click ‘mixer’ then you should see all the sliders for your devices;
You can independently adjust the levels for the right mix.
If you open the Beats panel and minimize it then a mixer slider also shows for this and you can dial in the effect of the EQ settings.
Headphones:
One last thing; When listening to headphones you will need to increase the bass EQ setting (since headphones can reproduce the low frequencies) in the Beats panel or I just change the drop down selector to the one with a flat curve (beats studio I think) -- the volume for my headphones was not an issue so I defeat the EQ for better sound quality.
Whew. I Didn't think it was this complicated when I started typing....
Hope everyone enjoys better sound with this.
JJ
ENVY 15 l i5 540M l ATI 5830 GPU l 8GB DDR3 1333 l 2 x 160 GB SSD l 1920x1080 glossy l Win7 Pro l 10,273 3Dmark06   Last edited by JJB : 12-27-2009 at 03:41 PM.
End of Excerpted Post
Credit belongs to the original author of the original procedure:
JJB from HP beats-audio / Sound Reset Procedure
Part Two
Loudness Equalization – and the LOW Sound Result
I was testing the system sound… CD playing in the background: Sting “If on a Winter’s Night” 02 Soul Cake playing through iTunes – standard speakers-headphones (beats-audio coasting along).
Sounds -> Playback Devices -> Speakers and Headphones -> Properties -> Enhancements
I have rewritten this part three times trying to get it right. Here’s the gist:
I switched on the “Loudness Equalization” enhancement. The sound jumped; it was loud and distorted. I switched the enhancement off – the sound dropped off and didn’t come back. I turned up the volume (with the slider) and down and up and down – and I was hearing Less and less sound from the speakers: “Low Sound Syndrome”: I was hearing what would be expected at setting of 7%. Well, that sucks. (Technical term.)
Based on this experience, I hypothesize that it’s possible to lose one’s sound entirely just by initially adjusting this one enhancement and then losing control over the ensuing ever diminishing returns. I didn’t continue to test this into a theory. It’s a hypothesis. If I had an extra dv7 sitting around, I might sacrifice it on such testing. I gave up right away and went into recovery mode while I still had some sound.
Recovery:
After the Loudness Equalization was turned off,
Recovery Attempts to recover normal sound levels included:
Resetting all Sound to Default settings,
Installing the driver from the webpage (standard load – download, double-click and install), reboot,
“Hard Reset”.
It was finally necessary to force load the IDT HD driver to recover the sound to its normal levels; that is, the driver was Uninstalled and allowed to reinstall at boot. (“Local” install from the Device Manager also works.)
Commentary:
I did not bother with a registry cleaning at this point - it may have made a difference, though it's unlikely since the driver needed to be completely reset by this time. I advocate registry cleaning! Bad things happen to good computers because of a dirty registry. Use your favorite or download CCleaner (free).
Try a Driver Update:
You can always check for Driver updates here – If the driver does update - you may be done with this part. Check the sound and proceed to "Enhancements".
At the Right-Click > Update Driver Software
Audio Driver “Uninstall”
Control Panel -> Device Manager -> Sound, video and game controllers
          Right-Click IDT High Definition Audio CODEC -> Uninstall
You have a choice at this point
If you do not have the means to replace your driver,
THEN do not delete your driver from the computer
OR - If you believe the driver is not working at all,
And / Or you have tried the standard Uninstall/self-install method previously without results,
AND You have the means to REINSTALL that driver from scratch*
Then you may delete the driver -
*Driver Installation From Scratch Requires the following:
You have your IDT HD driver on your computer as a sp*.exe file, for example, in Downloads
Reinstall with Boot:
Shut down the system
Reboot
The driver may install itself at login as the system scans for hardware changes
OR
Reinstall WITHOUT BOOT - Initiate the scan for hardware changes:
Right-Click on the IDT driver , > "Scan for Hardware Changes"
--> Check your sound at this point. It's possible that the driver has in reinstalled itself.
Manual Driver Installation - Comments:
There are a couple of paths used to get the IDT driver onto your system. You can download it from your HP Software and Driver website. You may have been given the path to your IDT driver at the HP ftp softpaq site. The package is downloaded as a sp*.exe file.   You may download the software as often as you need it. Make sure you have the package downloaded before you delete your driver.
Once you have downloaded that package onto your system, the original sp* file will stay intact. As long as you do not delete it, you can reuse it. Once you do install the driver onto your system, an installation directory is created in C:\SWSetup, named the same as the sp* file (without the .exe extension).
In C:\SWSetup\sp* are all the files necessary to reinstall your driver. If you install the software from the sp*.exe file in your Downloads folder, the new installation will ask you whether to overwrite the data in the SWSetup/sp* with the contents of the .exe package – do it. The reinstallation is just unwrapping and redistributing what’s in the .exe file into the same SWSetup/sp folder.
If the "Driver Store" is removed, that is, if the driver package is ever removed from C:\SWSetup, you can reinstall from the sp* file as long you you have it in your Downloads folder - it will recreate that SWSetup/sp* folder.
What about Versions?
Latest is Usually best. If you are concerned AND you think you may not be able to get another a copy of an older driver that is in C:\SWSetup\sp*, make a copy of the folder before uninstalling any driver or making any changes.
Installation from the Original sp* package
Find the sp* file on your system. It will be most likely be located in your “Downloads” folder.
Simple Driver Installation from the 'Saved' installation sp* file:
Close everything that isn’t needed, browsers, games, windows…
Right-Click on the installation package (the sp* file), Select 'Run as Administrator' and start the installation
Answer any questions…and follow the instructions
or...
Installation from the Device Manager
If the driver software is still on the system from a previous installation, it is located in C:\SWSetup
You can tell the Device Manager to access the package on the system:
Control Panel > icons > Device Manager > (Highlight) IDT High Definition Audio CODEC >
                      Right-Click > Update Driver Software > Browse my computer for driver software
                      Browse to C:\SWSetup\sp*
                      Be sure the “Include Subfolders” box is CHECKED
27-Nov-2011
Audio Services Check / Restart
This section is not strictly part of the "Enhancement" procedure. It has been included because it is necessary that these settings be correct so that the sound can function properly. If you are not having sound issues, skip this part...
Check system Services to make sure that your sound related services are running as they should.
Restart each service (except as noted): Right-Click > Restart
Control Panel -> icon -> Administrative Tools -> Services > bottom of page > Standard (optional - makes it easier to column sizes)
Sound services must be showing as
Status = Started
Startup Type = Automatic
Sound Services:
Audio Service
Multimedia Class Scheduler
Windows Audio
Windows Audio Endpoint Builder
Power (check only)
RPC (check only)
That’s it.
It’s a matter of tweaking the settings to get results. Do not forget that that Left/Right Speakers setting is turned off in Speakers Configure. It’s not a big deal (assuming this works), but it’s DIFFERENT and it needs to be kept track of.
I hope this helps your sound work better!
Kudos are Earned!
Kind Regards,
Dragon-Fur

Nice extensive research on reseting Beats Audio on the HP laptops.
Just bought the Envy 17t-3000 and I updated all the drivers via HP Support Manager.
BEFORE the update, the Beats Audio worked well..
1. Press the dial and the popup box comes up ~3 secs
2. Volume indicator swirl appeared to show volume level
AFTER the update, something changed the Beats Audio... had to re-install the latest driver from HP website (even after contacting HP Tech support via chat and email several times)...
1. Press the dial and the popup box comes up ~10-12 secs now!
2. Volume indicator swirl DISAPPEARED so volume level indicator is GONE
Sure the sound works but NOW I do NOT know or remember the volume level whenever I listen to music.
You can barely tell on the Windows Speaker icon on Icon bar since 2 sound waves indicate at least 50% sound level but that's it!
I have the following softwares and checked their settings and set them all at 50% and use the Beats Audio dial to control the volume whenever the programs are used:
1. WinAmp
2. VLC player
3. MPC
4. WMP
No matter what I try, it appears that the Beats Audio Volume Control Swirl Indicator is GONE! Worse, there's NO Windows volume control indicator unless leave the Volume Mixer open!
Anyone know how to fix this problem and bring Back the Audio Beats volume indicator??
Thanks!

My sound system is not working after my last updates on my imac,what shall i do to get fixed?

Hello any body who can help me out here?
My sound system is not working on my imac after the last updates,
WHAT SHALL I DO FOR????

apollos211,
You marked this as solved, so chances are no one else will respond.
You can try going Applications>utilities>audio MIDI set up, output tab and check to see if built in is selected.
Also check in system preferences>sound >output and see what is selected there.
If you look in the headphone port and see a red light (this means it is in digital mode), try taking a set off headphones and plugging them in and out several times also wiggle them around gently. There is a micro switch that sometimes gets stuck.
Hope this helps, if still no joy try reposting so that more contributers might check it, as once checked as solved it reduces the number of people checking.
All the best

IMac 10.6.8, Snow Leopard with iTunes 11.0.1. loss of wifi speed when connecting a Bose Sound System via bluetooth

Hello, I have an iMac 10.6.8, Snow Leopard with iTunes 11.0.1. When connecting my Bose Sound System via bluetooth the wifi downloadspeed goes from snappy to a crawl, disconnecting the bluetooth connection, the downloadspeed goes up again. Don't have this problems with the Sound System when connecting it to my iPad. I like to mention too, that the downloadspeed of my iPad is always better than of my iMac. Are there any experiences concerning this problem? Thank you in advance.

UPDATE - PROBLEM SOLVED!!!!!!
You can thank me later - after an hour on the phone, I finally got through to a Senior Engineer.
Apperently the issues lies with GRID VIEW.
Open your Itunes, Click on TV SHOWS, then quickly change your view from GRID VIEW (Defaults to this) to List View and Viola!
We tested it out on the phone just minutes ago, my problem is solved and I suspect if you guys try this yours will be too.

Trying to understand the sound system

Here's my problem. My mic didn't work (neither the front mic nor the line-in in the rear), so after some research and trial and error I found that if I do
modprobe soundcore
my mic works on both the jacks
But here's where my confusion lies. This is the output of lsmod |grep snd before probing explicitly for soundcore
[inxs ~ ]$ lsmod |grep snd
snd_hda_codec_analog 78696 1
snd_hda_intel 22122 1
snd_hda_codec 77927 2 snd_hda_codec_analog,snd_hda_intel
snd_hwdep 6325 1 snd_hda_codec
snd_pcm_oss 38818 0
snd_pcm 73856 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss
snd_timer 19416 1 snd_pcm
snd_page_alloc 7121 2 snd_hda_intel,snd_pcm
snd_mixer_oss 15275 2 snd_pcm_oss
snd 57786 8 snd_hda_codec_analog,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_pcm,snd_timer,snd_mixer_oss
soundcore 6146 2 snd
[inxs ~ ]$
So as you can see, soundcore's already loaded, so why do I have to explicitly load it again to get the mic to work?
Once I add soundcore to my MODULES array and reboot, the lsmod output is also the same as above.
So my question is -- what does the explicit loading of soundcore do, that is not done by auto-loading of that module?

Oh... since your topic is Trying to understand the sound system, that puts you (and me) inside the whole world's population... chuckle. But I thought I'd pass along a document written by probably "The" main ALSA developer that I totally stumbled across just 3 days ago.
Go here:
http://kernel.org/pub/linux/kernel/people/tiwai/docs/
and download the flavor of your choice of the "HD-Audio" document, or simply view it online. It documents the deepest dive into the current ALSA snd_hda_* layers and issues that I've found to date (but still leaves me wanting).
Why that document isn't plastered across the interwebs is beyond me. I only get 11 hits when I search for it... such are the secrets of the ALSA world I guess.
Last edited by pigiron (2011-08-26 18:26:48)

I am new to all this technology. I just hooked up apple tv but the sound comes only thru tv and not my sound system, any advice?

What do I need to do to make sound come thru sound system, not just tv when using apple tv?

How is the Apple TV connected to your sound system? Are you using the HDMI cable or an audio cable?

Hi, recently purchased macbook 13", I have problem with sound when connect to my LG Smart tv with sound system. When i change sounds effect on my sound system also LG its all go quiet didn't have this problem with my laptop. Any advise ?

Hi, recently purchased macbook 13", I have problem with sound when connect to my LG Smart tv with sound system. When i change sounds effect on my sound system also LG its all go quiet didn't have this problem with my laptop. Any advise ?

Some progess I see. To be honest, i would not waste your time with trying to connect using wireless.
You are likely to get poor connections and dropping out.
If its working using a cable, then there is no need to bother with giving me the network settings, bu see how it goes, because sometimes giving the TV a static IP address can give better results.
There is an example of a couple of powerline adapters on the diagram below. Just ignore the network switch unless you want to connect other devices which are near to the TV.
http://forumhelp.dyndns.info/networking/powerline3.jpg
I will monitor the subject line of this thread, should you want to post any more information.
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

Sound system

Similar Messages

Maybe you are looking for