Sound Turns off when opening MIAW

Hello,
I'm a beginner at Director and I've run into an issue. I
basically created an mp3 player which can open up a game I created
in a MIAW. The problem I have is that whenever the MIAW is opened
the mp3 player goes silent. The mp3 player and game utilize
different sound channels. Any clue what might be going on??? thanks
-izzy

Hi and welcome to the community! Since you're new please be sure that you have checked out our Discussion guidelines.
Just to clarify, does this only happen when using Spotify or does it impact other applications like Walkman too?
What are your thoughts about this forum? Let us know by doing this short survey.
 - Official Sony Xperia Support Staff
If you're new to our forums make sure that you have read our Discussion guidelines.
If you want to get in touch with the local support team for your country please visit our contact page.

Similar Messages

  • Sound turns off when listening to misuch thtough earphones

    My phone turn off the sound randomly when listening to Spotify with earphones. Have tested different volumes, but happens regardless of which volume it is. It is extremenly annoying, has anyone experienced this as well?

    Hi and welcome to the community! Since you're new please be sure that you have checked out our Discussion guidelines.
    Just to clarify, does this only happen when using Spotify or does it impact other applications like Walkman too?
    What are your thoughts about this forum? Let us know by doing this short survey.
     - Official Sony Xperia Support Staff
    If you're new to our forums make sure that you have read our Discussion guidelines.
    If you want to get in touch with the local support team for your country please visit our contact page.

  • Ipad turns off when opening photos app

    When i open my photos on ipad 1 16gb wifi i turns off then about a minute later it shows apple logo and it back on
    any ideas and how to fix?
    thx in advance ben

    Try a Reset [Hold the Home and Sleep/Wake buttons down together for 10 seconds or so (until the Apple logo appears) and then release. When the screen goes blank then power ON again in the normal way.] It is 'appsolutely' safe!

  • All sounds turned off when they should be on!

    Help - my phone no longer rings or makes any noises when recieving texts, notifications, unlocking or typing etc.
    When I go to settings everything appears to be turned on so I can't figure out how to fix this?
    Please help!

    Is the silent switch on?  It's the switch above the volume controls on the side.

  • Why did the swoosh sound turn off in Mail?

    Why did the swoosh sound turn off when I send and e-mail message in Mail?
    Thank you.
    jcbmillard

    First is your volume turned up and not muted?
    Also check system preferences/sound/sound effects, make sure play sound effects thru internal speakers is checked, make sure alert volume is turned up (not all the way down), Play user sound effects id checked.

  • When the sound turns off on my macbook, the miniplug stereo port emits a wildly uncontroled load leading to noise.

    When the sound turns off on my macbook and my macbook pro, the miniplug stereo port emits a an enormous 'pop', i.e. wildly uncontroled load leading to noise. Goundline hum follows. I am running OS 10.6.6. I have noted previous threads noting the same problem on OS 10.4.x and 10.5.
    How do I stop my mac from trying to ruin my stereo and speakers every time I connect them?

    You don't say which year you have, however...
    ...there are known problems with the mid-2010 models (see http://support.apple.com/kb/TS4088?viewlocale=en_US&locale=en_US) as well as early and late 15" 2011 models (see https://discussions.apple.com/thread/4766577?tstart=0).
    Apple has taken ownership of the problems with the 2010 model but, unfortunately, the free logic board replacement for that model has probably long expired for you - three years after date of purchase.
    One the 2011 models Apple has admitted no defect. You'll just have to skim the articles to get an overview of the problems that people are having (usually showing up as screen glitches at first and then going downhill from there).
    Good luck,
    Clinton

  • Macbook freezes or turns off when I try to open .ppt, .pptx, .pps files

    macbook freezes or turns off when I try to open .ppt, .pptx, .pps files

    Which model Macbook Pro do you have?  If you really have a Macbook, post in their forums.  Macbook Pro and a Macbook are 2 different type of computers.
    It is very difficult to offer troubleshooting suggestions when the "os version" you are using is unknown as each os has their own troubleshooting solutions. 
    Please describe in detail all you have attempted to do in order to resolve the issue. 
    Please complete or update your system profile so the users here can properly help you. 

  • Alarm clock on iPad turns off when I open cover:

    Recently (the last 2 weeks) when I have an alarm on my iPad set to go off in the morning, this is what happens: I hear the alarm going off. I open the cover to hit snooze. In the past, when I opened the cover, I had the option of hitting snooze or ok. (Ok to turn off alarm clock alarm.). The odd thing that's been happening now is, when the alarm goes off, the minute I open the cover, the alarm stops. I can't hit snooze or OK, because opening the cover is triggering the alarm to turn off. I haven't changed any settings. No one else uses my iPad 2. It's not happening every day, just randomly. I have rebooted my iPad, but it still does it. (more often than not!). Thanks

    music turns off when i open emails on my iphone 5s. How can I fix this?

  • Why does my music turn off when I open Safari on my iPhone 5c?

    I noticed that my music turns off when I open safari on my iPhone 5c. What's the deal?

    I figured out this will happen if any of the pages that are open in safari on your phone are open to a page that contains media.  Note this means any page regardless of whether it's the one you are viewing.  So if you go to a site that has media, then open a new browser window and go to a page that doesn't have media and then open iTunes and play a song...when you switch back to safari, the music will stop.  If you close the first browser window and try it again...the music will continue to play.

  • Sound drops off when using hdmi outport to connect computer to an AV reciever

    Satellite M640,I5 2410 processor, windows 7HP. After about three minutes the sound drops off when connected to the av reciever through the hdmi outport. If I touch the trackpad the computer reconnects for another three minutes and  then disconnects. If I touch the the trackpad about every two minutes the computer stays connected indefinetly. This problem does not occur if I use the computer to play an audio CD. Any fix suggestions.

    Hi peter,
    try to repair your permission by open application folder > utilities > disk utility > repair permission.
    It should fixed the unexpectedly quit for several applications.
    And try to get latest info from Griffin sites, maybe this one will help too:
    http://www.griffintechnology.com/support/article.php?artnum=314
    ps: why not try macbook built in microphone?
    Good Luck.

  • Horizontal spry menu style appears turned off when on the internet though can view it in live mode!?

    The style of the horizontal spry menu seems as to have been turned off when on the web though is visible and functioning on CS4 Dreamweaver design and live views. I have styled the spry menu and can view it in the properties section though the style setting is there on the internet it looks as if the styles have turned off and appears unformatted vertically when it should be a cascading horizontal menu bar. Not sure where the error is, I have looked at the coding and as I'm not the most experienced with spry.....
    this is the coding above the head.
    <script src="../SpryAssets/SpryMenuBar.js" type="text/javascript">
    <link href="../SpryAssets/SpryMenuBarHorizontal.css" rel="stylesheet" type="text/css" />
    <!--
    var MenuBar1 = new Spry.Widget.MenuBar("MenuBar1", {imgDown:"SpryAssets/SpryMenuBarDownHover.gif", imgRight:"SpryAssets/SpryMenuBarRightHover.gif"});
    //-->
    </script>
    I have noticed that SpryMenuBarHorizontal.css doesn't appear in the spry assets folder, does this matter? (not sure how to insert into the assets menu).  Any help would be greatly appreciated!

    thanks for testing it. I'm not sure how to proceed though as the css file is in my local_sites/spry assets folder for the website. I've tried to point it to other (copies of SpryMenuBarHorizontal.css) and spry assets folder externally from the site and again internally in the root folder and seems to make little or no difference.
    Your suggestion of what it should read,(sorry to sound so naive at all this) though would you mind giving a step-by-step guide on how to go about it? as I'm obviously missing something in the setup process.
    thanks again for your help.

  • Macbook works fine when plugged in, turns off when unplugged.

    Hello all,
    As stated my 2008 Unibody 13 inch, serial number W8******1AX turns on and works fine when it is connected to power.
    When it is unplugged it instantly turns off and turns its fans on full until it depletes the battery (so it is obviously getting power.. just not where I want it)
    Since the problem began I have tried two new batteries, neither of which had any different symptoms.
    Before this, the computer had an intermittent life, it would turn off when it saw fit, which got progressively worse.
    I have followed the guides to resetting the SMC but have had no luck
    I have been running it without the battery (to save it charging and discharging for no reason) and sometimes when plugged in without a battery
    the magsafe green indicator light goes from dim to bright.
    With the battery installed it stays bright orange until it is charged and then switches to bright green.
    (I have tried it with another charger, same symptoms)
    Here is the Battery Read out;
    Battery Information:
      Model Information:
      Serial Number:          ?00€›Æ⁄¬+9tt
      Manufacturer:          GSA-1280
      Device Name:          ASMB016
      Pack Lot Code:          3230
      PCB Lot Code:          30db
      Firmware Version:          ddae
      Hardware Revision:          dac2
      Cell Revision:          2b39
      Charge Information:
      Charge Remaining (mAh):          4113
      Fully Charged:          No
      Charging:          Yes
      Full Charge Capacity (mAh):          4200
      Health Information:
      Cycle Count:          1
      Condition:          Normal
      Battery Installed:          Yes
      Amperage (mA):          379
      Voltage (mV):          12275
    System Power Settings:
      AC Power:
      System Sleep Timer (Minutes):          15
      Disk Sleep Timer (Minutes):          10
      Display Sleep Timer (Minutes):          5
      Automatic Restart on Power Loss:          No
      Wake on AC Change:          No
      Wake on Clamshell Open:          Yes
      Wake on LAN:          Yes
      Current Power Source:          Yes
      Display Sleep Uses Dim:          Yes
      PrioritizeNetworkReachabilityOverSleep:          0
      Battery Power:
      System Sleep Timer (Minutes):          2
      Disk Sleep Timer (Minutes):          10
      Display Sleep Timer (Minutes):          1
      Wake on AC Change:          No
      Wake on Clamshell Open:          Yes
      Display Sleep Uses Dim:          Yes
      Reduce Brightness:          Yes
    Hardware Configuration:
      UPS Installed:          No
    AC Charger Information:
      Connected:          Yes
      ID:          0x0100
      Wattage (W):          60
      Revision:          0x0000
      Family:          0x00ba
      Serial Number:          0x00ebc719
      Charging:          Yes
    Power Events:
    Repeating Events:
      Type:          Wake or Power On
    If this at all helps.
    I'm at my wits end with this thing, I know it is getting on in age, but other then this, it has been flawless in its operation.
    If anyone has any suggestions I would be happy to hear them.
    Many thanks!!
    <Edited By Host>

    There may be a hardware cause behind the symptoms you cite, so a diagnostic
    is recommended to see which parts are weak or failed in the computer. A visit to
    an Apple Store with Genius bar may be helpful, as they can perform testing there.
    A call ahead or use their web page, to schedule an appointment, is advised.
    In the US and Canada, the Genius bar at a retail Apple Store can perform
    a diagnostic service, for no fee, even on Apple products without AppleCare.
    See links:
    Apple - Concierge
    Genius Bar - Apple Retail Store:
    http://www.apple.com/retail/geniusbar/
    List of Apple Stores, cities, countries:
    http://www.apple.com/retail/storelist/
    Also authorized Apple service providers who can test, repair and guarantee their
    work should be able to handle an out-of-warranty older Mac, within age limits...
    Ones too old for the Apple Store could be serviced at a Specialist, instead.
    •Find Locations - Sales, Service, Training, Consulting:
    https://locate.apple.com/
    •Did you try resetting the System Management Controller?
    Intel-based Macs: Resetting the System Management Controller (SMC)
    •A reset of NVRAM may help with some issues:
    About NVRAM and PRAM
    •Calibrating is part of maintenance, esp with older portables:
    Apple Portables: Calibrating your computer's battery for best performance
    •The power adapter can be problematic and cause issues, so there's this:
    Apple Portables: Troubleshooting MagSafe adapters
    Also another item, other than keeping the magnetic connections clean of
    debris, grime, and corrosion, is to check the MagSafe Board or have it
    checked as part of a greater diagnostic. This board is behind the port
    that supplies the computer and the battery with power from the adapter.
    When it partially fails or if/when one of the connecting wires or plug fails
    you can find odd issues or partial use. The battery may charge but it
    may not be able to power the computer, and other odd effects.
    https://www.ifixit.com/Device/MacBook
    In older portable Macs, this was generally called a 'DC-in board' and as
    such, you could read about it in an iFixit repair guide for the MacBook
    model you have. These vary so the matching article is recommended to
    see if that is something you may want to try. But I would have diagnostic
    testing done and avoid additional damages from attempted DIY efforts.
    There have been a few reports of other failure on the logic board that
    contributes to a partial failure of the charging system, so about all this
    may do is troubleshoot around the failure without finding an exact cause.
    However it goes...
    Good luck & happy computing!

  • I'm sure your'e going to tell me I just need a new phone but maybe there is hope for my iphone 4.  It will not charge past 66% (it's not the charger), it turns off when unplugged, and it will not even let me turn my wi fi to the on possition.  Help!

    'm sure your'e going to tell me I just need a new phone but maybe there is hope for my iphone 4.  It will not charge past 66% (it's not the charger), it turns off when unplugged, and it will not even let me turn my wi fi to the on possition.  Help!

    Hi there 8472kck!
    I have some information for you that can help you troubleshoot this issue a little further. That information can be found right here:
    Will not turn on, will not turn on unless connected to power, or unexpected power off
    Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
    Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion. Learn about LCIsand corrosion.
    Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
    After at least 15 minutes, if:
    The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen . Then unplug the phone from power. If it immediately turns off, seek service.
    The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
    Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
    If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.
    If the display turns on, go to step 4.
    If the display remains black, go to next step.
    Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
    If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.
    and that information comes from this article:
    iPhone: Hardware troubleshooting
    http://support.apple.com/kb/TS2802
    Thanks for being a part of the Apple Support Communities!
    Regards,
    Braden

  • TS1398 my iphone turned off when using wifi

    my iphone turned off when using wifi

    That sounds like you have internal damage in the SIM card slot. Try taking the phone to an Apple store for evaluation. Make a genius bar appointment first at http://apple.com/retail.

  • How to turn off "re-open all application windows"

    How to turn off "re-open all application windows". Even though its unselected in preferences. my computer still tries to do this and causes startup problems and delays. its been a hangup since lion. when are they going to fix this???

    Try this. . .
    You have two choices. You can choose that your applications not resume their previous state when you shutdown or restart the Mac by deselecting the checkbox that appears prior to shutdown:
    Or you can navigate to the General pane in System Preferences and deselect the Restore windows when quitting and re-opening apps option. However, if you do this, applications will never resume their previous state, even when quit and restarted during a single boot session.

Maybe you are looking for