Sound works with speakers but not without.

The sound suddenly went off earlier today,can hear when plugged into speakers or head phones only?

Try the following to rule out a software probleM
- Reset. Nothing will be lost.
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Restore from backup
- Restore to factory defaults/new iPodIf you still have the problem you likely have a problem with the headphone jack in the iPod. They can be replaced. I would make an appointment at the Genius Bar of an Apple store to identify/determine the cause.

Similar Messages

Sound works with headphones but not with computer speakers

I've got an iPhone 3GS and an iPad. A few weeks ago I setup an older pair of computer speakers in my living room and I've been using that as a bookshelf stereo. I just plug in whatever device happens to be around, the phone or iPad to drive the music.
Tonight though, the iPhone will not output any sound to the computer speakers. It will play music through the external speakers without any issue - same for the iPod headphones. Originally I chalked this up to an issue with my speakers, but when I hook the ipad up to them, I get sound.
Any ideas as to what this could be? The phone worked fine until tonight and I've tried to restart the phone and turn it off.

Hey polofson,
Thanks for the question. I understand you are experiencing issues with Siri in relation to your microphone. On the iPhone 5, Siri utilizes both the mic in the receiver opening and the mic near the rear camera. You may want to make sure these are not blocked (commonly by third-party cases):
iOS: Troubleshooting Siri
http://support.apple.com/kb/TS4079
Ensure that Siri can clearly hear you
If Siri is unable to clearly understand what you are saying, make sure your microphones are not blocked.
iPhone 4s
Verify that the bottom microphone, located to the left of the dock connector, is not blocked.
iPhone 5
Verify that both the mic in the receiver opening and the mic near the rear camera are not blocked.
iPod touch (5th generation)
Verify that the mic near the rear camera is not blocked.
iPad (3rd generation)
Verify that the mic at the top center, above the FaceTime camera, is not blocked.
All models
- If you are using a protective case, try removing it.
- Try turning your device off and then on again.
Thanks,
Matt M.

Siri works with headphones but not without headphones

Ever since I installed iOS 7, Siri has not work through the microphone, only with the headphones. I have checked everything. The microphone works fine with the phone, but not with Siri. This has to be a bug in iOS7. Cany anyone heklp with this issue. If so please respond
Thanks
<Email Edited by Host>

Hey polofson,
Thanks for the question. I understand you are experiencing issues with Siri in relation to your microphone. On the iPhone 5, Siri utilizes both the mic in the receiver opening and the mic near the rear camera. You may want to make sure these are not blocked (commonly by third-party cases):
iOS: Troubleshooting Siri
http://support.apple.com/kb/TS4079
Ensure that Siri can clearly hear you
If Siri is unable to clearly understand what you are saying, make sure your microphones are not blocked.
iPhone 4s
Verify that the bottom microphone, located to the left of the dock connector, is not blocked.
iPhone 5
Verify that both the mic in the receiver opening and the mic near the rear camera are not blocked.
iPod touch (5th generation)
Verify that the mic near the rear camera is not blocked.
iPad (3rd generation)
Verify that the mic at the top center, above the FaceTime camera, is not blocked.
All models
- If you are using a protective case, try removing it.
- Try turning your device off and then on again.
Thanks,
Matt M.

My iPods internal speaker isn't working, the sound works with headphones but now without. I've turned it on and off several times and pulled the headphone out and put them back in but nothing seems to work, please help?!

My sound usually works but just yesterday it totally just stopped. The sound is turned on full, the headphones are out, and I've tried turning it off then back on but it didn't help at all. It's an iPod touch 2nd generation, 8G.

Try the following to rule out a software probleM
- Reset. Nothing will be lost.
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Restore from backup
- Restore to factory defaults/new iPodIf you still have the problem you likely have a problem with the headphone jack in the iPod. They can be replaced. I would make an appointment at the Genius Bar of an Apple store to identify/determine the cause.

My bank id works with IE but not in Firefox, even if I run without extensions. What is the problem?

My bank id works with IE but not in Firefox, even if I run without extensions. What is the problem?

Make sure you are using the correct user name / password.
https://support.mozilla.org/en-US/kb/firefox-cant-load-websites-other-browsers-can
https://support.mozilla.org/en-US/kb/secure-connection-failed-error-message

My sound works for music but not apps

My sound works for music but not apps

Try this - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.)
Check your settings. The iPads have a small switch on the right edge. It can be used as a rotation lock to keep the screen from automatically reorienting itself as you move around, but you need to have the tablet’s settings configured properly. That same switch, right above the volume buttons, can also be set to function instead as a mute button to silence certain types of audio.
If the switch is set to work as a mute button, you can change its purpose to “screen-rotation lock” by tapping the Settings icon on the home screen. On the Settings screen, tap General on the left side, and on the right side of the screen flick down to “Use Side Switch to.” Tap to select Lock Rotation or Mute to set the button’s function. Even if you set the side switch for your preferred use, you can still mute the Mini or lock the screen. Just double-click the Home button, and when the panel of apps appears along the bottom edge of the screen, flick the row from left to right with your finger. Tap the icon on the far left side of the row to either lock the iPad’s screen or mute the iPad’s alerts, notifications and sound effects. Music, podcasts and video are not muted unless you turn the volume all the way down.
iPhone: No sound or distorted sound from speaker
http://support.apple.com/kb/ts5180
iPhone: Can't hear through the receiver or speakers
http://support.apple.com/kb/ts1630
http://www.atreks.com/app-no-sound-on-ipad-4-%E2%80%93-what-to-do/
To solve some sound problems, just follow these simple steps
1. Go to Settings
2. Tap on General
3. Tap on Reset
4. Tap on Reset All Settings
 Cheers, Tom

Better touch tool works with touchpad but not magic trackpad, better touch tool works with touchpad but not magic trackpad

better touch tool gestures works with touchpad but not magic trackpad, why please ?

this was an error problem solved

UTube video sound works on iPhone5S but not on Macbook Pro?

UTube videos from a variety of sources works on iPhone5S but not on Macbook Pro? Thinking it has to do with recommended Flash settings on the MAC. Is there an app to resolve this inoperability on a MAC without having to make Flash active?

What format is the video? Is it .wmv? Do the DVD's have any type of protection or encryption? This information will help in finding a solution.

Strange on - Wake on LAN (WOL) works with Win2K3, but not Windows 7

Hi,
I have a PC that I originally had Windows 2003 on. With Win2K3, I can send a wakeonlan (magic) packet (WOL) and get it to power on remotely from my home network/LAN.
I just installed Windows 7 Ultimate 64-bit, in a dual-boot configuration, i.e., so I can boot the machine to either Windows 7 Ultimate 64-bit or Win2K3.
As mentioned, I can power the machine up remotely (from my home network/LAN), but if I've LAST booted into Win7, then shutdown, it doesn't respond to the WOL packet.
I've confirmed that if I boot into Win2K3, then shutdown, the WOL works fine.
I have another PC that has both Win2K3 and Windows 7 (also dual boot), and that works fine with WOL.
One difference between the one that doesn't work vs. the one that works is that the one that works is a machine that I just built a couple of weeks ago, which uses an MSI 880gm-E43 motherboard.
The one that doesn't work also has an MSI motherboard, but it's an older one, an MSI K9NBPM2-FID.
I've cross-checked the various Windows power management settings between the one that works, and the one that doesn't work, but I just can't get WOL to work with Win7 on that older machine. I've even turned the Windows Firewall off completely on the machine where WOL isn't working, but no matter what I've tried thus far, no joy :(...
The only thing that I can think of is that the network card driver (it's the MS one, from the Win7 distribution) might not work with WOL, but I've checked, and it's the latest driver from MS (Nvidia Nforce Networking Controller - 10/17/2008 - 1.0.1.211), and MSI doesn't have a specific Win7 64-bit driver for this motherboard.
So, I was wondering if anyone has any ideas about this?
Is there some registry setting or something that might allow WOL to work?
Thanks in advance,
Jim

Hi,
Unbelievable!
Just for the record, I got WOL working with the older machine, JUST after I posted the original msg.
Here's what I did:
- I was in Device Manager, and did Update Driver, but
- I selected to let me choose, and then I checked the "Show Compatible devices" checkbox
Then, a 2nd, older (10/6/2006 - 6.2.0.127) driver appeared, so I figured, "what the heck?" and tried that. I then shut the machine down, and sent a WOL packet to it, and kind of forgot about it (machines in a different room), but a few minutes later "bing!", the machine had powered up and booted into Win7!!
Anyway, as I said, for the record, and hope that this helps someone in the future.
Jim

XPath query works with CLOB but not with object relational

hi all
i have the following queries,the XQuery work with all, but XPath queries work with XMLType CLOB and Binary XML, but they do not work with XMLType as Object relational,
select extract (object_value,'movies/directorfilms/films/film [studios/studio = "Gaumont"]')
from xorm;
select extract (object_value,'movies/directorfilms[director/dirname = "L.Cohen"]/films/film[position()=2]/t')
from xorm;
they shows this message
ORA-00932: inconsistent datatypes: expectd SYSTEM.name683_COLL got CHAR
thanks

Hi Marco
fisrt here is my RO
BEGIN
DBMS_XMLSCHEMA.registerSchema(
SCHEMAURL=>'http://......../ORMovies.xsd',
SCHEMADOC=>bfilename('DB','Movies.xsd'),
LOCAL =>false,
GENTYPES=>true,
GENTABLES=>FALSE,
CSID=>nls_charset_id('AL32UTF8'));
END;
create table XORM of xmltype
xmltype store as object relational
XMLSCHEMA "http://......../ORMovies.xsd"
ELEMENT "movies";
INSERT INTO XORM
VALUES(XMLType(BFILENAME('DB','ORMovies.xml'),nls_charset_id('AL32UTF8')));
here the XQuery format that work fine with the OR
A/D
select XMLQuery ('for $a in movies/directorfilms/films/film
          where $a/studios/studio = "Gaumont"
          return $a'
     passing object_value
     returning CONTENT)"TitleX"
from xorm;
child element query
select XMLQuery ('for $a in movies/directorfilms/director[dirname = "Feyder"]
          let $b:=$a/../films/film[position()=2]
          return $b/t'
     passing object_value
     returning CONTENT)"TitleX"
from xorm;
here is the XPath format which doesn't work
select extract (object_value,'movies/directorfilms/films/film [studios/studio = "Gaumont"]')
from xorm;
select extract (object_value,'movies/directorfilms[director/dirname = "Feyder"]/films/film[position()=2]/t')
from xorm;
by the way all queries work fine with the CLOB or Binary XML
many thanx Marco

Ichat works with wireless, but not ethernet

Just moved into new office and bought new iMac. I can get internet with ethernet or wireless, but iChat works only over wireless. This is true with my intel Macbook as well. Is this a port or firewall problem, and if so, why would wireless work, but not ethernet?
Core2 Duo 24", 1 g ram Mac OS X (10.4.9)

Who is supplying the wireless internet connection?
Who is supplying the wired internet connection? If
it's two different entities, the IT Secret Police may
be blocking ports on the wired side.
TimeWarner comes in from the outside, but a private contractor is involved in the setup of the wireless which is connected to the TW modem. But if the wireless goes into the TW cable, why does it work as wireless, but not directly plugged in? It is as if converting the signal to wireless cures the problem.
Core2 Duo 24", 1 g ram Mac OS X (10.4.9)
Core2 Duo 24", 1 g ram Mac OS X (10.4.9)
Core2 Duo 24", 1 g ram Mac OS X (10.4.9)

Why does the FP 10 work with firefox but not with IE8

I down loaded the folowing for xp FP uninstall, FP plugin and FP debug from the link in one of your replys. now I can watch youtube with firefox but not with IE8. you asked me before if i was using 16 bit. whats that mean and how do I find out? please help I just want to watch youtube on IE!

Ok Shag, since you hadn't been on a Forum before, then I'll take some of what I said back:-) I wanted you to stay on one thread, you can get in trouble trying things that may cause you more problems than you had in the beginning. I just had your best interest at heart
I'll even overlook your all caps here:-) At least you responded
Now since you say you fixed it, what you should do is to confirm it is fixed by taking a look at your Flash folder. This contains all of the Flash files for IE and FF. Then make sure you have the IE add on and the FF add on. That way if you have any future problems, at least you would know it is not the Flash Player.
You should only have 2 .exe files for IE and 1 for FF.
For Video editing, I would check Microsoft and see what they have. Perhaps someone else will come along with other info for you.
No, I don't get paid here, since I am not an employee. Just a user helping others, since I had a problem at one time and after 4 hours of researching solved it.
Let me know if you want to check the Flash files.
Thanks,
eidnolb

When I click on pictures in eBay or Facebook. It will not show the pictures....Will work with IE but not FF

When I click on pictures on eBay and Facebook...it will not show pictures/enlargements...just blanks....will work with IE. NOT ff

You can use these steps to check if images are blocked:
*Open the web page that has the images missing in a browser tab.
*Click the website favicon ([[Site Identity Button]]) on the left end of the location bar.
*Click the "More Information" button to open the "Page Info" window with the Security tab selected (also accessible via "Tools > Page Info").
*Go to the Media tab of the "Tools > Page Info" window.
*Select the first image link and scroll down through the list with the Down arrow key.
*If an image in the list is grayed and there is a check-mark in the box "Block Images from..." then remove that mark to unblock the images from that domain.
See also:
*http://kb.mozillazine.org/Images_or_animations_do_not_load
There are also extensions (Tools > Add-ons > Extensions) and security software (firewall, anti-virus) that can block images.
*https://support.mozilla.org/kb/Troubleshooting+extensions+and+themes

Airtunes works with music but not with tv show

I have an AE wired to my to my A/V receiver and I play itunes music wirelessly thru the AE and it works fine. Problem: I downloaded a TV show and the audio will not stream via the AE and will only play thru the computer. The video works fine fine in both cases as I have it hooked to my TV via my A/V receiver from my Macbook display port. I am running itunes 8.1 and my AE is on firmware version 7.4.1.
Anyone know why the songs audio works and the tv show audio does not?

Thanks for that fast and definitely a fix at this time. It also works with internet radio, not just the iTunes radio stations. Now my wife will be able to listen to KFOG from San Francisco and I can actually hear my movies, since I am using a MacBook and it is just not loud enough.
Thanks Again Andy.
I love these forums.

Madison Square Garden web site opens but when I click on view all concerts tab at the MSG site it does not open. It works with AOL but not Firefox

I go to '''www.thegarden.com''' I click on the tab '''View Full Calendar'''. It does not open. It works on AOL but not Firefox. And for some reason it also does not work when I use Internet Explorer. The majority of times when I click on that tab (in Firefox) it does not work. On a rare occasion it will open. I am not doing anything differently either time.
Any help would be greatly appreciated.

Clear the cache and the cookies from sites that cause problems.
"Clear the Cache":
* Tools > Options > Advanced > Network > Offline Storage (Cache): "Clear Now"
"Remove Cookies" from sites causing problems:
* Tools > Options > Privacy > Cookies: "Show Cookies"
Start Firefox in [[Safe Mode]] to check if one of the extensions is causing the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > Appearance/Themes).
*Don't make any changes on the Safe mode start window.
*https://support.mozilla.com/kb/Safe+Mode
*https://support.mozilla.com/kb/Troubleshooting+extensions+and+themes

Sound works with speakers but not without.

Similar Messages

Maybe you are looking for