Soundblaster Audigy 2 ZS - Vista - speaker calibration etc

Hi,
I've searched but I can't find an obvious answer to what I suspect is a common question.
I've got an Audigy 2 ZS Pro which I've just installed using the drivers from the site. It's working ok but there is no applciation for set up of the speakers in a room - as there was in the original CD that I used with XP.
Can anyone help? Or am I just imagining that a utility did exist when I last installed this on an XP machine?
Thanks
PH

JRe: Soundblaster Audigy 2 ZS Platinum - Speaker issues not covered by FAQs0 I'm afriad that the CMSS3D option did not work? ? I still cannot get any speakers to play out of the rear of the soundcard.
As I said before, the goal is to try to get sound to play out of both the headset and the speakers attached to the rear of the soundcard simuntaneously.
The headset is plugged into one of those devices in the front that is in a 5 & /4" bay that has the individual knobs for adjusting volume for the headset and outbound levels for the microphone.
The speakers are plugged into the back of the soundcard and do not play any sound in any of the sockets, starting from the firewire port and counting 3 over.
Any suggestions? I? thought it might have something to do with the setting of the speakers from control panel - > Sounds and Audio Devices -> Advanced and picking the right choice there. No luck however. Same for the Creative Speaker Settings as well.
I'm at wits end and I'd be very thankful to whoever can resolve this for me. =)

Similar Messages

Speaker Calibrator with Latest Vista Driver (1/1

My original Vista driver for my Audigy 2 ZS timed out over the weekend, so I downloaded and installed the new one. Unfortunately, now I only get sound out of one speaker (the front-left one) on my 7. speaker setup. And every time I try to run the speaker calibrator to fix this, I receive the following error message:?Error obtaining Calibrator Interface!? Please install and register CTSCAL.DLL. I haven't been able to find any information related to this error message on Google or in the Creative knowledge base. Does anyone else know what's going on or how to fix it's? I'd really like to be able to hear at least STEREO sound again, and preferably 7.!
Thanks,?--Matthew

I don't think any of the cd's software works with the newer drivers. I think all that works right now is the driver, the new MediaSource Player, and the new cd update for MediaSource. Try uninstalling everything and then just install the driver package and the new MediaSource Player and the cd update for it. You'll get AudioConsole. Unfortunately you'll also find that DVD Dolby Decoding has been removed, as well as the EAX stuff with the exception of the environments for old games that don't use EAX. The MediaSource Player will also only rip and encode to burn in Wave or Windows Media Formats unless you purchase a Creative AudioCodec plugin. A user here who probably had the cd stuff installed found that the new player does do mp3 encoding for free if the older software is on the system. Since that stuff doesn't work on Vista I decided not to install it, or all its stupid background processes that can't be turned off since the software won't open. (Well, we can delete the items from the registry run key I suppose.)?Make sure that when you uninstall the driver in Device Manager you check the box that tells it to remove all related files and software. I would reboot, remove the Multimedia Audio Device that will be in Device Manager after Vista fails to find a driver when it automatically tries. Then restart again and let it fail to install the driver. (Let it automatically try then fail.)? Then install the latest download. Some have had the installer not recognize a Creative SoundBlaster Hardware (a noted problem historically with Creative installers). I think resetting the Device Manager as I suggested might jog the registry so that the Creative installer will work. Cross your fingers. If not, extract the download and run the DriverSetup.exe from the Driver folder, restart twice, then run the Setup (the original download) again. It will then probably uninstall the driver, restart the computer, install the new driver and then AudioConsole. Don't restart right away when that is finished. Let Windows boot up, then restart the computer. Things should work fine after that. I'm using the new driver on a fresh Vista Business install and it sounds great. I need to adjust bass and treble from the Windows controls or the WMP EQ though, as the AdvancedEQ is not there. So, you set up your speaker configuration from Creative AudioConsole, and the rest from the Windows Mixer and playback and recording devices Windows control. Don't run the Windows speaker setup. It just messes things up (don't even open the button). You should get 5. (or whatever you have).

Soundblaster Audigy 2 ZS Platinum - Speaker issues not covered by FAQs

FSoundblaster Audigy 2 ZS Platinum - Speaker issues not covered by FAQs? ?
Greetings..
Running into a bit of a issue here I can't seem to fix. I've gone through the troubleshooting guides and FAQs already and they aren't resolving the issue.
My normal setup is a couple of desktop speakers plugged to the rear of the card through the standard ports (non-digital) and a headset with mic plugged to the device in front that includes volume controls for both mic and speakers.
I've just did a complete reinstall of Windows XP (32 bit) including everything up through SP3 and a reinstall of the drivers and associated software applications for the card as well.
The problem I am having is that I can no longer make the rear speakers (desktop speakers) play when plugged in. The 2 headset speakers still play just fine that are plugged in the front however.
What should I do to resolve this issue so that I can have both the desktop speakers and headset speakers both playing? I'm fairly sure I'm just missing a setting somewhere but for the life of me I can't figure where to fix this.
Thank you,
Culann HS

JRe: Soundblaster Audigy 2 ZS Platinum - Speaker issues not covered by FAQs0 I'm afriad that the CMSS3D option did not work? ? I still cannot get any speakers to play out of the rear of the soundcard.
As I said before, the goal is to try to get sound to play out of both the headset and the speakers attached to the rear of the soundcard simuntaneously.
The headset is plugged into one of those devices in the front that is in a 5 & /4" bay that has the individual knobs for adjusting volume for the headset and outbound levels for the microphone.
The speakers are plugged into the back of the soundcard and do not play any sound in any of the sockets, starting from the firewire port and counting 3 over.
Any suggestions? I? thought it might have something to do with the setting of the speakers from control panel - > Sounds and Audio Devices -> Advanced and picking the right choice there. No luck however. Same for the Creative Speaker Settings as well.
I'm at wits end and I'd be very thankful to whoever can resolve this for me. =)

Creative L3500 Speaker system and Soundblaster Audigy 2 ZS Soundcard (I have a driver probl

Yes I have had a driver problem so i went to the download section of this site and picked up a driver program for my soundcard yet it doesn't work. When i do uninstall my soundcard (i need to uninstall current driver to install new driver)and i restart my comp after removing the old one i get sound, but i notice i don't get very good sound, not as good as my old before it stoped working. But then after i install new one it just doesn't work!
Please help me if you know about drivers!!!!
PS: I use windows XP and if you need any more info just request it from me.Message Edited by Nick345 on 02-28-200605:05 PM

JRe: Soundblaster Audigy 2 ZS Platinum - Speaker issues not covered by FAQs0 I'm afriad that the CMSS3D option did not work? ? I still cannot get any speakers to play out of the rear of the soundcard.
As I said before, the goal is to try to get sound to play out of both the headset and the speakers attached to the rear of the soundcard simuntaneously.
The headset is plugged into one of those devices in the front that is in a 5 & /4" bay that has the individual knobs for adjusting volume for the headset and outbound levels for the microphone.
The speakers are plugged into the back of the soundcard and do not play any sound in any of the sockets, starting from the firewire port and counting 3 over.
Any suggestions? I? thought it might have something to do with the setting of the speakers from control panel - > Sounds and Audio Devices -> Advanced and picking the right choice there. No luck however. Same for the Creative Speaker Settings as well.
I'm at wits end and I'd be very thankful to whoever can resolve this for me. =)

What happened to the Speaker Calibrator Wizard from the Audigy 2?, why is it Go

Hi, there I know the X-fi has a Speaker Calibrator Wizard in the thx section as in the audigy 2, however the part where there is the basic and advanced calibration options that guide you to calibrating your system aren't there. Also the surround mixer on the audigy 2 isn't there where you can control the levels of all 7. speaker channels, ie move the surround channels to half way up and down.
I really miss this feature, and can anyone from Creative support give me a link to get the software back. I currently have the x-fi elite pro and I really want to calibrate my speakers using that utility.

If any of you are unfamilar with this, note that in the thx setup console in the audigy 2 there were some options, in which creative had a choice of either basic or advanced calibration. The x-fi doesn't have that option.

Connecting Soundblaster Audigy 2 to 2 speaker syste

Hi all,
I am using a Soundblaster Audigy 2 ZS. My PC is connected to a 7. Creative THX system.
That is working pretty fine.
I also have my LCD TV connected to my PC as secondary display and I've got a Teufel 5. system which I want to connect to the audigy.
Reason: I want to watch movies played on my PC on my normal television. I could of course connect the audigy to the Teufel system, BUT this would mean switching cables all the time (from PC 7. to TV 5.).
Is there some kind of high quality switch with which I could save this reconnecting of cables all the time?
Thanks a lot in advance.
and kind regards
Sven

Hello all,
I am having a similar issue. I would like to connect my Audigy 2ZS to a Sony Reciever (STR DE-898) preferably via the digital out. The sound card and reciever are 25 feet apart.
I have read that the digital out on the Audigy 2ZS is specifically for creative lab speakers, and that if you connect it to a normal reciever that it may damage the reciever is this true?
Second, the other option that I have is to buy the 7. adaptor and connect RCA extension cables to the reciever.
The last option is to connect it to the regular headphone jack out, and use an extension cable to connect to the reciever (This is what I am currently using), but the sound quality is terrible.
Please help, I read the recent post on digital out ,which helped some, but still the question remains... if you connect the digital out on the Audigy 2ZS to a Sony receiver will this damage the receiver?Message Edited by asharabi98 on 05-27-2006 0:38 AMMessage Edited by asharabi98 on 05-27-2006 0:39 AM

Creative Soundblaster Audigy 2 Zs help

Before I start rambling on about my problem here are my specs (BTW I'm not incredibly computer literate; my dad helped me install everything before I left for school):Cpu: Intel Duo Processor 2.66 GhzRAM: .5 GB DDR2Video Card: ATI Radeon 9600 (soon to be one of their newer models)OS: Windows XPSound Card: Creative Soundblaster Audigy 2 ZS?Ok so I was reinstalling everything after I had to format my computer. I get through installing my creative sound card and figure everything went great. I was playing my music when I had realized that I forgot to configure my sound card for them, as I was getting mono instead of stereo (was only playing out of left speakers). So I go into speaker setup and click on "calibrate speakers" or something like that. Anyway, the speaker calibrator says that It could not be ran for some reason (i forget). I figure that it wasn't working because I hadn't updated anything yet. I update, and I still get the same message. So I reinstalled the software and updated it again and now when I try to run ANY of my creative software related to the sound card (I.E. EAX console, Speaker Setup) it says that "The Audio device supported by this software is not detected. The Application will now shut down."? Now remember that I'm not great with computers, so my solution now will probably sound stupid. But anyways I figured that I had installed the wrong sound card software (it gives me three choices on the disc). I uninstall everything and choose another setting. I still got the same problem. So I try the third choice and I get the same problem. Any suggestions? I've tried all three choices and I still get the same problem.

tony8gj wrote:
I have the SoundBlaster Audigy 2 ZS sound card installed in my Dell 8400 PC. Does anyone know what the latest SoundBlaster Audigy 2 ZS driver version is? I currently have driver v 5.2.4.445 and date 8.7.04 I've tried to install this from the Creative site: SBA2_PCWDRV_LB__84_55-R.exe but keep getting a "setup could not detect and sound blaster audigy 2 on your system" error. The driver on the Dell site is: Creative Labs SoundBlaster Audigy 2 ZS: R92022.exe Thanks! Tony.
Hi
You may first need to patch the driver package by using ctcomp.exe to get std. drivers (eg. not Dell specific) installed to your Dell PC. Search this forum after ctcomp.exe --> there you'll find some instructions too.
You can also find a link to the latest drivers available (I personally use Audigy 4 drivers from november 2005 --> can be found from creative support pages) by searching this forum (I think the latest WHQL version is .~62 for the original version).
jutapa

Creative SoundBlaster Audigy Advanced MB software activation probl

Hello!?I bought?a software named Creative SoundBlaster Audigy Advanced MB, when I ordered my notebook Inspiron 720 from DELL, on the 8th? of September, 2007. They provided a CD for the software, which I installed, and it worked. But then later that day (when I recieved the laptop), I formatted the hard-disk for the following reasons - ) It only had 2 partitions for the entire dri've, one of which was a recovery partition, and I wanted to create more.2) I wanted to remove MediaDirect.3) I wanted to remove bloatware that DELL gave me with it, ie, DELL Quickset, DELL Support, DELL this, DELL that, Norton AntiVirus etc.4) I wanted Vista installed by my way. After I had done everything I wanted, I started to re-install the Creative software, the same way like I did before. But this time, when it took me to the transaction page and asked me for the reason of re-installing this software, it said "The CD Key has expired."?I have tried 2 different browsers,?I have cleared my cache, I have penta-checked my CD-Key before each install and have done anything a Computer Software engineer (me) would do, with the help of the Internet as well. But my every effort went in vain. Then, I did something I didn't want to do, I contact DELL technical support. Their solutions ranged from installing the latest drivers (yes, drivers for a software), to removing and re-installing the latest Internet Explorer (yes, they asked me to REMOVE IE) to put the HARDWARE in some other machine. Quite clearly, the 4 support executi'ves I talked to there at DELL had no clue as to what is going on and what is the problem. Then, after a 2 hours chat with another one of them, I was told that they just provide the software, and it is Creative's duty to handle everything later and asked me to talk to you. The email support page do not have the option of support for this software, so I selected some other product but sent my problem.
It would be very nice to know if there exists a solution to this problem, and how should I approach it. It has only been 20 days since I bought this software. Thank you!

Finally, I got a reply from the email team, and they sought some further information, which I duly provided. Then, they provided me with a new CD Key. But here is the thing, they say after 3 times of re-installing the software, I will have to pay for it. What?Why would I pay for something which I bought, again and again? The whole world knows about Windows Vista, how incompatible it is with more than 80% of the software, and it will be the same till SP is released. I have since this Sunday gone have re-installed vista 4 times, once due to the fact that AHCI in the BIOS was not enabled by default, and I had to re-do the installation, then it was SATA drivers not presentonthe Vists disk, then the nVidia drivers had problem with Vista and it crippled it and won't go and then the Windows Media Player , quite clearly still not fully functionable, made my system bust. And I can say that it will happen again, so why do I have to pay some part of the software's price again? I am not using it on any other machine, and that is checked by it's CRC checker anyways, I am not using it for any business project, which shouldn't be a problem even if I did, as I own it. If any of you guys have an answer to this, please let me know.
Thank you, and have a very nice day all!

PAX Live-Audigy Se Vista 7 v1.00

PAX Li've-Audigy Se Vista 7 v.00
Creative all rights be long to Creative and logos. Creative giving me there writing persimmon by Robert McClelland.
PAX related logos and software and drivers are own by PAX
- Please don't remod my work with out permission you can contact me at Hardwareheaven.com
Celebrating
5 years of PAX drivers.
- Vista/Win7 32/64Bit - Read me
PAX
Performance Audio Xeleration
Tweaked Drivers for Creative Soundcards:
Better Performance. Better Audio. Better Xeleration.
Tweaked Edition
Supported cards:
PAX Li've-Audigy Se Vista 7 v.00
Supported OS:
Vista, Win7
32 and 64Bit
Based on:
SB24_PCDRV_LB__04_0090
+ Updated Tweak As of .08.0
+ Support Speaker Default to 5.
Important :
Before installing, remove all traces of any previous drivers and all driver related software, using add/remove programs within the control panel and following that, by removing the driver within "Device Manager". To clean up any excess files left on your system, you should use a 3rd party program to do this job (unless you've a good understanding of the registry) A recommended program to do this is Driver Sweeper - which is freeware, and available from http://www.guru3d.com/category/driversweeper/ or paid version at hardwareheaven.com driver cleaner.net
To install the software suite and driver :
Providing you've followed the steps above, restart your computer and run Setup.exe. Follow through the prompts until the installation has completed.
Please used register cleaner like tune up Advanced SystemCare iobit.com or crapcleaner
Please make sure you installed lastest direct x included in the suite of June 200 if you haven't done so.
What is Pax
Formally known as Youpax, Pax was founded by Robert McClelland 5 years ago, who is continuing to provide an alternati've tweaked driver to the Official driver released by Creative.
Why should I install this Pax alternati've
Pax is aimed at improving sound quality and to give a more deeper bass sound, while retaining the clarity of the overall output audio. Most users continue to use Pax drivers once moving over and never look back!
PAX 2005-200
http://dl.technewshw.com/drivers/PAX/PAX%20Li've-Audigy%20Se%20Vista%207%20v.00.7z

& What did you especially fix or add? I have surfed all around in gameheaven forums and other places but the only thing you wrote is" better performance, better exelaration etc" . I dont think it is enough , you HAVE TO tell which software modules you added or what you have tweaked.
If I were you I would take a look at Daniel_k's threads and take them as reference before posting..................

How to install The Soundblaster Audigy SE in Windows 7 RC?

:How to install The Soundblaster Audigy SE in Windows 7 RC?Y Two days ago I bought a Soundblaster Audigy SE-retail soundcard. I have a dual boot PC with Windows XP-SP3 and Windows 7 RC. The installation of the soundcard?in Windows XP was easy, no problems, good sound.
But how to install in Windows 7 RC ?
I have the installation and applications CD with XP and Vista drivers and I have the driver-download from Creative.com SB24PCDRV LB 0 - 04 - 0090.
Windows 7 tells me "No device for audio output is installed". Windows automaticly?installed a driver, but that doesn't work. (code 39). The driver download from?creative does not install new drivers and when I try it manually Windows tells me "The best driver is already installed"
When I uninstall?the driver that Windows installed and try to install the downloaded?creative driver for Windows 7, the driver will not install, and Windows message is something like "?no audio device is installed on this computer"
What to do ? A computer without sound is nothing...
Thanks,
Arie

>Re: How to install The Soundblaster Audigy SE in Windows 7 RC?% Meocene is 00% on the money. Dan K.'s pack is the best. I have used the pack on four different systems with AUDIGY LS and SE cards that I bought cheaply (all four on Ebay for $40). The package has worked under XP, Vista, and Windows 7 very well.
I have friends that play Left4Dead and they have been immensely pleased when playing the games in their flats with or without headphones, as compared to their old "onboard RE--t-k" sound.
The package also works well on a Gateway or HP machine when disabling onboard audio first then installing the Audigy and installing drivers and apps for the first time. Gi've up on using your old CDs, you will only run into a mountain of trouble trying to "Auto-Update" all that with the newest patches.

Speaker Calibration Wizard not working at a

Hi all,
I've just recently purchased a second-hand Audigy 2 ZS Platinum Pro. I've downloaded the Audigy 2 ZS Series driver disc (courtesy of a poster on this forum) and installed all fo the software from there. I have also updated the main windows driver, to the latest version availiable from the Creative site.
Everything is hunky-dory thus far, however i have found one issue with the software. Whenever i try to start the "Calibrate Speakers" wizard in the "Speaker Settings" page, nothign happens. There is a brief flicker of activity form the HDD, and then it stops? I've tried reinstalling the "Speaker Calibration" software from the driver disk, but that hasnt solved anything.
As always, any ideas or thoughts would be greatly appreciated.
Cheers
--Jakk

Hi all,
I've just recently purchased a second-hand Audigy 2 ZS Platinum Pro. I've downloaded the Audigy 2 ZS Series driver disc (courtesy of a poster on this forum) and installed all fo the software from there. I have also updated the main windows driver, to the latest version availiable from the Creative site.
Everything is hunky-dory thus far, however i have found one issue with the software. Whenever i try to start the "Calibrate Speakers" wizard in the "Speaker Settings" page, nothign happens. There is a brief flicker of activity form the HDD, and then it stops? I've tried reinstalling the "Speaker Calibration" software from the driver disk, but that hasnt solved anything.
As always, any ideas or thoughts would be greatly appreciated.
Cheers
--Jakk

Connecting Soundblaster Audigy 2zs to Home Theater Amplif

Can I connect my Soundblaster Audigy 2zs directly to an amplifier and still get 5.,6.,or7. speaker setup? I feel it's kind of redundant to use a reciever when the Audigy has all the capabilities of a Home Theater Reciever. And it outputs sound at 92khz, which currently is only available on more expensi've recievers.
My goal is to use my pc as a souce and connect it directly to amps and speakers. I would like to put money I save on recievers into a high end speaker system
I have read in the previous posts that it may be possible to do 5. by getting an mini jack to RCA adapter for each channel. But no details on 6. or 7..

I am in the same situation as you. As the CL told me
http://forums.creative.com/creativelabs/board/message?board.id=soundblaster&message.id=5343 --
You can either use the audigy to decode the sound or your reciever to decode the sound with the SPDIF passthrough. Just whichever has the better specs.
From my situation I would recommend having speakers with analog hookups to the front/rear/center sub rather then the digital output. The only way to take advantage of the digital output is with a DVD and in that case you can just watch a DVD on your TV rather then your computer. For games the analog 5. hooks is better as well because with games it decodes it and with your reciever it would only have 2. sound.

Soundblaster Audigy 2 ZS - static no

Hi,
I have a Soundblaster Audigy 2 ZS soundcard in my Dell Dimension 4700 computer. Recently I started getting a lot of static - like rice crispies crackling.
It would go away sometimes after powering down, but come back after a few hours. After reading some of the posts here I tried moving the card further away from the video card. This seems to allow me to run longer without the static - a few days was my last try. But the static did come back and I had to power down to get rid of it. Now I am static free for several hours, but I think it will be back. I can't move the card any further away now - it is in the last slot. I'd appreciate any feedback on ways to fix my problem and what exactly my problem is. I don't really understand what is causing the static. Thanks in advance,Steve

I have the same card -- and the same problem -- in my Dell XPS Gen 3 system.
Two weeks ago, I started getting constant static though my speakers. I didn't know what the source of the problem was and, since I have a year left on my warranty, I called Dell tech support. I subsequently embarked on a two-week troubleshooting nightmare which involved all sorts of fun stuff including:
A system restore (rolling everything back to factory settings and having to reinstall everything)which did not solve the problem
Determination that I had faulty speakers (which turned out not to be the case after the speakers were replace with brand new ones)
Complete reformatting of my hard dri've and a full reinstall of the operating system (Windows XP Professional (turns out the XP professional disk I got with my computer actually contained XP Home, so I am looking forward to another round of reinstalling the OS once Dell ships me the proper software). The reinstall did not solve the problem.
The Dell people finally had me relocate my computer and 6-piece speaker system to another room (to see if an electrical source was causing the static). Static was still there.
They finally determined that the problem was in the Creative sound card, even though their diagnostics gave it a clean bill of health. My guess is that one of the input jacks developed a bad connection with the card after 2 years of use.
I have not yet received the replacement sound card. I'm crossing my fingers that when the new one arri'ves, the static problem will disappear.
So if you work through Dell tech support, do yourself a favor and cite my problem. It may save you hours and hours and hours of frustrating troubleshooting.
To be fair, I have to say that the various Dell tech reps I worked with were very thorough, polite, and accommodating. They did things by the book, which is really the only way to approach a mystery problem like the one I'm having.
The downside is, during the past two weeks, I've spent more time trying to get my computer back in shape than I've spent working (I'm self-employed). But it was also a learning experience and I now know a lot more about computers than I did before.
I hope you get your sound card problem solved quickly with less pain and suffering than I went though.

Soundblaster Audigy 2 ZS Platinum Remote prob

I have had this problem ever since I bought the Audigy 2 ZS Platinum.
My creative remote works fine but the External I/O Module accepts any sigal from any of my other remote controls. So if I want to change anything else in the room like the tvchannel or increas volume on the amplifier, the audigy thinks that i want to change someting like mute och start mediasource player.
At first i thought this was normal but now I cant find anyone else with the same problem.
Everything works fine except for the remote problem. Is this enough to get a new Audigy 2 ZS Platinum?

JRe: Soundblaster Audigy 2 ZS Platinum - Speaker issues not covered by FAQs0 I'm afriad that the CMSS3D option did not work? ? I still cannot get any speakers to play out of the rear of the soundcard.
As I said before, the goal is to try to get sound to play out of both the headset and the speakers attached to the rear of the soundcard simuntaneously.
The headset is plugged into one of those devices in the front that is in a 5 & /4" bay that has the individual knobs for adjusting volume for the headset and outbound levels for the microphone.
The speakers are plugged into the back of the soundcard and do not play any sound in any of the sockets, starting from the firewire port and counting 3 over.
Any suggestions? I? thought it might have something to do with the setting of the speakers from control panel - > Sounds and Audio Devices -> Advanced and picking the right choice there. No luck however. Same for the Creative Speaker Settings as well.
I'm at wits end and I'd be very thankful to whoever can resolve this for me. =)

Soundblaster Audigy on MSI K8N Diamond Plus, Sound Linked? vs Audigy2 ZS?

Had a couple of quick questions regarding the Soundblaster Audigy onboard chip on my MSI K8N Diamond Plus. I have the audio connected to a front panel, and when I try and change the Right or Left speaker volume balance in Windows (by going to volume control and dragging the balance slider right or left), the volume slider goes down and the balance slider snaps back to center. As in my previous post, I had some damage to my front panel connector pins and wanted to make sure this wasn't a hardware issue requiring a replacement of the board.
Also, I have a Soundblaster Audigy2 ZS card from my previous system, and I was wondering if it added anything the onboard Soundblaster chip doesn't provide. I was thinking of installing it, but if the onboard audio does everything the card would, I'd rather just use the onboard solution.
Thanks.

Quote from: syar2003 on 21-August-06, 06:59:38
Onboard creative is just live24 marketed as Audigy SE
live 24bit is an audigy SE striped down of some features.

Soundblaster Audigy 2 ZS - Vista - speaker calibration etc

Similar Messages

Maybe you are looking for