Spa 2102 with power led flashing red

anyway to fix this? cannot access the unit via pc or ivr. BTW this is the second unit that has done this in the last 2 months

Im just guessing but sounds to me its the firmware or its not configured right.
Thats all i can think of at the time.
I hope you the best in gettin it fixed.
The default IP address for the adaptor is  192.168.0.1
Push that in the address bar on the brower.
Try the user name....user
The the password.....admin
Message Edited by sjl24 on 07-23-2007 08:19 AM

Similar Messages

  • Pxi 8360 power led flashes red

    I have a PXI 8360 MXI Express board mounted in a PXI 1050 chassis. I am seeing the power LED occasionally flash red and I lose communication with the computer. The power LED will return to solid green status after a few minutes but I am not able to do much with NI DAQ to test the system since it has failed self test. The suspicion here is the power supply may be bad but how do we check that.
    The system with the computer has worked well over the past several years and we are concerned about possible damage from a power fluctuation that happened here around Christmas time.

    Hi Xavier,
    The red flashing light is on the PXI 8360. I have not seen any flashing lights on the chassis.
    The modules present in the system are
    PXI 8360  MXI Express
    PXI 4071  7 1/2 digit flex DMM
    PXI 4110  Programmable DC power supply
    PXI 4110
    PXI 4110
    PXI 8252  1394 Host Adapter
    TB 2627  multiplexer terminal block
    PXI 6289  M series multifunction DAQ
    SCXI 1306
    SCXI 1303
    SCXI 1303
    SCXI 1300
    So far all testing has been done with all modules installed. Another person has tried reseating all modules to see if that would fix the problem but it does not.
    The system will work fine for a few hours and then the blinking LED will begin and somewhere near that time the communications fail with the computer. The light will blink for a few minutes and then will return to solid green. Once the error has occurred it seems that the only way to re establish proper operation is to shut down the whole system, PXI chassis and computer, and restart. I saw one time where the power LED on the 8360 went from flashing red to solid green when the computer was turned off.
    The computer is  a Dell Precision 690 with PCIe 8361.
    I will be opening up the chassis hopefully in the next day or two to check fuses and voltages where I can.
    Bill

  • PXI Chassis Power LED Flashing Red: What to do?

    My NI PXI-1042 keeps blinking red the Power LED. I know it means the voltage is out of the specs. What to do?

    FilipeTaveiros wrote:
    But it is not continuously red.. It is blinking red.. Thanks for your help. Anyone? 
    This is copied right out of the manual: 
    The chassis power switch has an integrated LED. This LED indicates one
    of three different conditions:
    • If the power switch LED is steady green (not flashing), the chassis is
    powered on and operating normally.
    • If the power switch LED is flashing green, the air-intake temperature
    has exceeded the chassis operating range.
    • If the power switch LED is flashing red, the power supply outputs are
    not within voltage regulation requirements.
    You either have a power supply problem, or you are loading it down with too many modules.  Try running it empty and see what the light does. 
    Using LabVIEW: 7.1.1, 8.5.1 & 2013

  • My z10 led flashing red when charging and even at battery full it blinks red. no green at any note..

    My z10 led flashing red when charging and even at battery full it blinks red. no green at any notification. But at below 10% charging level it blinks with a combination of red and green. Please send me any settings to be changed if.. at full charged no green light is blinking.. how many colours does z10 led have..and when it works and how to make those settings..or was my led not working fine? I am worried so much..plz help me

    Your LED is fine, on the Z10 there is not "network signal available" green LED, as you're accustomed to from the legacy devices. At reaching 10%, the LED will blink orange.
    Red for message or applicaiton notifications.
    if you want to edit and create specific LED color combination, see the third party apps such as BeBuzz or Hub++
    1. If any post helps you please click the below the post(s) that helped you.
    2. Please resolve your thread by marking the post "Solution?" which solved it for you!
    3. Install free BlackBerry Protect today for backups of contacts and data.
    4. Guide to Unlocking your BlackBerry & Unlock Codes
    Join our BBM Channels (Beta)
    BlackBerry Support Forums Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • I bought my 6 plus last night decided to upgrade the IOS 8 like they suggest and now all I see is a white screen with the apple sign in the middle with an occasional flashing red screen. Did my new phone seriously just crash? What do I do now?

    I bought my 6 plus last night decided to upgrade the IOS 8 like they suggest and now all I see is a white screen with the apple sign in the middle with an occasional flashing red screen. Did my new phone seriously just crash? What do I do now? I left it overnight with the white screen, thinking maybe it'll go away and needs time to upgrade. Woke up this morning, nope still white screen. Very disappointed with Apple. I was so excited to get my phone and can't even use it right now.

    First turn the iPhone off and back on and see if it works.  If that doesn't work then do a Reset by holding the Sleep / Wake Button (The Power Button) and the Home Button at the same time until the white Apple Logo appears, the release both Buttons and wait until a Full Reset occurs.  The iPhone 6 should come back to your Lock-Screen.  If that doesn't work then you could connect the iPhone 6 via the Lightning Cable to a Computer with a Current Version of iTunes.  Then open iTunes on the Computer and wait until your see a Button that represents your attached iPhone and click on it.  This should bring up a Summary Screen on the Computer within iTunes.  At that point your can choose Update Software if an Update is available or Restore the iPhone to Factory Settings / New In The Box, or you could try to Restore from your Backup if a current Backup had already been saved from a previous iPhone.
    If you don't have a computer with iTunes and you can get the iPhone back on, then go to Settings>General>Software Update and see if the iPhone is still on iOS 8.0 or if it is now on iOS 8.0.2

  • Z10 - blank screen + led flashing red

    On connecting my new Z10 with BBlink, was given a an option for available upgrades. On upgrading the screen went blank and LED flashes red - 3 short 2 long - blank and starts the sequence again. Am unable to restore, restart or anything. Help wanted please email. 
    Solved!
    Go to Solution.

    Glad, that you were able to resolve the problem, Hopefully future releases of the BB link would work better with Mac's..

  • Satellite A200-AH1 - power LED flashes blue

    Hi
    Ok I got a old laptop it's a Toshiba A200-AH1 it's was working ok then just stop ... the wannabe IT Tech in my home town said that it was the External Power adaptor so we bought a brand new one now all that it does is flashing ... si to be sure i'm talking about the blue light beside the picture of a power cable the one to the left of all the little pictograme of cd, battery, HD ect ect ect
    The rate of flashing is steady at bout 2 blink per second more or less
    Please help me out

    Hi
    From my knowledge the power LED flashes only if an error has been detected on the motherboard.
    I think you should contact the Toshiba authorized service provider in order to find out what is exactly wrong with your notebook.
    I think the ASP technician has more experience with Toshiba notebooks as an common wannabe IT technician.
    Good luck

  • Playbook won't turn on, boot, or charge. LED flashing red.

     Playbook won't turn on, boot, or charge. LED flashing red.

    Try this, while connected to your charger. Press and hold the Power key, up and down volume (-/+) all three buttons simultaneously, for about 10-12 seconds. You should the red LED blink and that should allow a reset of the PlayBook and to power up.
    1. If any post helps you please click the below the post(s) that helped you.
    2. Please resolve your thread by marking the post "Solution?" which solved it for you!
    3. Install free BlackBerry Protect today for backups of contacts and data.
    4. Guide to Unlocking your BlackBerry & Unlock Codes
    Join our BBM Channels (Beta)
    BlackBerry Support Forums Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • SPA-2102 automatic power cycle problem

    I have the SPA-2102 with one VOIP line.  Often it will power cycle automatically every 15 minutes or so.  All three lights go off for a second and then it comes back up and works for another 15 minutes.  I had my provider replace the first one as they thought it was a faulty unit but the new one is doing the same thing.  If this happens when I am on the phone the line goes dead and disconnects.
    Also I was getting close to 5Mbps then it suddenly seemed to cap out at 4Mbps once this problem arose.
    Suggestions?
    Thanks

    If you observed that every 15 minutes the SPA2102 is really turning off, is can be a sign of harware problem. I suggest contacting Cisco Tech support to further look into your concern. I believe this unit belongs to the business series devices that Cisco is now supporting. Try to go to this link for the other business series devices and the site where you can get hold of Cisco for support: 
    http://www.cisco.com/web/products/linksys/index.html

  • SPA-2102 with Cisco Unified Communications Manager (callmanager)...

    Has anyone used SPA-2102 with a UCMgr or CallManager?
    If you do.... how many DLUs (device license units) do you need for each SPA-2102?

    I have tried to get the SPA2102 to register to CUCM with no luck.  However, there was another way to get them to talk.
     Setup a Cisco router with SP Services IOS as a SIP Gateway.  Build a "voice" dial-peer for incoming calls, build another for outgoing calls to the SPA2102, and another to the CUCM.
    Configure the SPA2102 to NOT register with SIP Proxy and to point to the Cisco router instead.
    This costs NO DLU's.
    Depending on how your dial-peer's are configured you can have both lines appear as the same number.or different numbers.

  • Power led flash when i try to start up my Mac Pro.

    I have a Mac Pro (Early 2008). I have now got a problem. I can't start it up.
    When i start it by pressing the Power switch the fans inside start to sound and the powerled beside the power swich starts flashing.
    After that nothing more happens ( i have waitind for several hours), I have to stop the Mac by pressing the Power switch.
    It looks like the Ram is OK becouse the lams on the Ram boards lights up abd then turns of agian (no indication of error);
    i have changed to backup battery and reset the PARAM and SMC with no effect. i have also removed all extra Harddisks and also
    the Graphic card to see if ther was any problems with these.
    So i guess the the flasing Power led is an indication somthing is wrong but i can't find an expanation when i search the net.

    So i guess the the flasing Power led is an indication somthing is wrong but i can't find an expanation when i search the net.
    Yes it is.
    If it is single flashes something is wrong with your ram.  A red diagnostic led may be lit on the riser that failed.
    If the flashes are in groups of 3 a bad dimm slot (or slots) were detected and there should be lit diagnostic leds next (or near) to the dimms that failed.
    Try reseating your dimm no matter how it is blinking.  But look inside for lit diagnostic leds anyhow.
    Also blow all the dust out of your machine while you are in there.

  • Router WRT54G Power led flashing!

    hi,
    Somebody can help with this issue, I have a WRT54G router v.3.1 the power led is flashing and I can not access to configure the router, I tried everything, I tried using a static IP on my lan card and I can not access to doing a ping, I tried press and hold the reset buttons for 1 minute and power down for a 30 sec and nothing happended, the led still flashing. When a connect the straight UTP cable on my computer the connection icon appears blinking but I can not access to configure the router for any way.
    someone have a new suggestion?
    this is a critical case to me and I appreciate all the help that you give me.
    Thanks for advance,

    you will need to upgrade the firmware...
    now since you are able to ping the router using a static ip....first download the latest firmware from the website (make sure that u get the .exe file) . then run the file normally....it should upgrade the firmware.

  • Blackberry Pearl 8100 randomly shuts off and the status LED flashes red

    My pearl was reciently unlocked and changed from AT&T service to t-mobile. after this switch the pearl started having fits of rage where it will turn off randomly, weather any keys have been hit or even if it is idle. the device LED then flashes red, sometimes once, other times it will flash once every 4 seconds for hours. then it will randomly turn back on either to the exact screen it had been on before it powered off or it will reboot completley and start the normal start-up procedure and varify security checks just as if the battery were removed. i tried removing the batery and leaving the phone disassymbled for a few nights but in the morning the plague is back and unrelenting. sometimes all i have to do it pick the device up and it will shut off. other times i will be plugging away with it for 20 or so minutes on the internet and then it will die suddenly. it also cuts out in the middle of phone calls. if anyone can help,please let me know.
    blackberry 8100 v4.2.1.96

    Is it a new phone? If it's less then a month old see if you can return it, otherwise you can try reloading the OS.
    So if you're willing to try that, do the following.
    First download and install the Desktop Manager from here (4.6 without Media Manager is recommended): https://www.blackberry.com/Downloads/entry.do?code=A8BAA56554F96369AB93E4F3BB068C22
    Next you can use the Backup and Restore feature present in the software to make a backup of all the data on your phone.
    Next download and install the handheld software from here: http://na.blackberry.com/eng/support/downloads/download_sites.jsp
    Afterwards try reloading the OS by connecting the device to your computer, open the Desktop Manager, then go into the Application Loader. This will open a wizard that steps you through reloading the OS onto your device. More detailed steps can be found here:
    http://www.blackberry.com/btsc/KB03485
    If someone has been helpful please consider giving them kudos by clicking the star to the left of their post.
    Remember to resolve your thread by clicking Accepted Solution.

  • Power LED flashes, firmware updates good, and can still access the router

    I have a wrt54G first version as there is no version number. About two months ago, the power led started dropping out and with a reset worked for a day or so, then, it became worse, every hour, and now only a couple of minutes. according to the help side of this site, the router will not be accessible, but it is. I upgraded to the 4.7.1.1 firmware, the problem continues, un plug and start it up. Any ideas? Could it be the 12 volt power supply going bad or over shooting the power?

    yes, that is the level, verified at the router. the help side of this site says that if the led flashes like this that it would be corrupt an un accessible, but a restart of the router stops it, and it is accessible, moreover, the upgrade fails since that is the level at the router. just that it is happening about every 15 minutes (8/3) - could it be that comcast is sending packets of ??? to blow out routers? Thee state they don't like people using routers - that you are not supposed to use more than one computer with their broad band connection. Yes - serious, the e have said this twice in the last 6 months. Don't know what it could be, Saturday - Sunday it has not dropped out at all

  • MacBook Power Cable Flashes Red! Computer Dies!

    Hi, i have a macbook and the laptop battery broke a few months a go and now it only works whilst using a power cable. But over the past 2 weeks i have found that the light on the power cable sometimes flashes red and then the laptop dies, do you think this is a problem with the cable? and getting a new one would fix it? or is it a problem with the laptop its self.
    Help

    Hi LexSchellings,
    Thank you for your quick response.
    My 15" MacBook Pro was bought in March 2010 and has recently been upgraded to Lion OS. The MBPro has been playing up for a while, so I have also had the hard drive and the motherboard replaced. In fact, I picked it up from Apple less than a week ago with the replaced motherboard. The reason for replacing the motherboard was because the MBPro was crashing all the time.
    It was running fine all week including last night, but when I tried to switch it on this morning it was dead. Since the powercable that came with the MBPro did not show a light at all when connected, I tried an older powercable and this is when I noticed that the amber light was flashing.
    I'm taking it in to a Geniuys bar tomorrow, so hopefully they should be able to sort it out.
    Again, many thanks for your response.
    Trond

Maybe you are looking for