SPA 502G Web interface

Hi I am junior admin and because we have 1 port /working place I need to configure that IP phone and pc are connected together. I configured VLANs, and port is configured as trunk. When I configure (via Phone settings) VLAN membership, phone is operational but PC is not. I read that there is PC vlan ID somewhere , but if I try to access it via Web I can only see configuration, and cannot change. There is no login button, so that I can log in with that account. Can you please help me and explain how to access admin page ?
Firmware version is 7.4.8a, there are some older one also. I plan to upgrade to newest firmware.
Regards,
Alex

It's because you are supposed to configure via the UC500. In SCCP mode, the config is supposed to be pushed down from the UC as opposed to SIP mode.
You can see if you can get the admin layout to show up. Press **# on the keypad and see if you can get the additional parameters to show up in the phone UI. Then in the web UI, see if you can go to the System tab and change the Phone UI read only to no.
If that still doesn't allow you to make the changes that you want, you can factory reset and make your changes to the VLAN when the phone is in the default SIP mode. Then plug into the UC500 setup.
But ideally, you're suppose to make all the changes through the UC500 system.

Similar Messages

3850 web interface slow to load, especially for webauth

Hi all,
Got a cat 3850 switch acting also as a wireless controller. Running 3.6.0E One thing that I've noticed is that loading the web interface to configure it is terribly slow. Also for guest authentication, it takes a long time for the web page to load. Tried IE and firefox with same results.
Thoughts?

Hey thanks for the reply Rasika. Yes, I'm aware that the GUI isn't quite there yet. However for the webauth, I would expect it to be somewhat fast. The webauth file is custom, but small.
Here's the contents of the flash directory and some config:
3850#sh start | inc webauth
aaa authentication login webauth_local local
service-template webauth-global-inactive
parameter-map type webauth global
parameter-map type webauth guest_web
type webauth
custom-page login device flash:/webauth/webauth_login.html
custom-page success device flash:/webauth/webauth_success.html
custom-page failure device flash:/webauth/webauth_failure.html
custom-page login expired device flash:/webauth/webauth_expired.html
security web-auth authentication-list webauth_local
security web-auth authentication-list webauth_local
3850#sh flash:
-#- --length-- ---------date/time--------- path
2    2097152 Oct 24 2014 20:58:23.0000000000 +00:00 nvram_config
3     742912 Oct 20 2014 19:16:56.0000000000 +00:00 webauth.tar
4       4096 Oct 20 2014 19:16:58.0000000000 +00:00 webauth
5       4096 Oct 20 2014 19:16:57.0000000000 +00:00 webauth/css
6       2098 Oct 20 2014 19:16:57.0000000000 +00:00 webauth/css/signin.css
7         96 Oct 20 2014 19:16:57.0000000000 +00:00 webauth/css/starter-template.css
8       4096 Oct 20 2014 19:16:57.0000000000 +00:00 webauth/dist
9       4096 Oct 20 2014 19:16:57.0000000000 +00:00 webauth/dist/css
10      19791 Oct 20 2014 19:16:57.0000000000 +00:00 webauth/dist/css/bootstrap-theme.css
11      17706 Oct 20 2014 19:16:57.0000000000 +00:00 webauth/dist/css/bootstrap-theme.min.css
12     126432 Oct 20 2014 19:16:57.0000000000 +00:00 webauth/dist/css/bootstrap.css
13     102897 Oct 20 2014 19:16:57.0000000000 +00:00 webauth/dist/css/bootstrap.min.css
14       4096 Oct 20 2014 19:16:57.0000000000 +00:00 webauth/dist/fonts
15      20290 Oct 20 2014 19:16:57.0000000000 +00:00 webauth/dist/fonts/glyphicons-halflings-regular.eot
16      62850 Oct 20 2014 19:16:57.0000000000 +00:00 webauth/dist/fonts/glyphicons-halflings-regular.svg
17      41236 Oct 20 2014 19:16:57.0000000000 +00:00 webauth/dist/fonts/glyphicons-halflings-regular.ttf
18      23292 Oct 20 2014 19:16:57.0000000000 +00:00 webauth/dist/fonts/glyphicons-halflings-regular.woff
19       4096 Oct 20 2014 19:16:57.0000000000 +00:00 webauth/dist/js
20      58327 Oct 20 2014 19:16:57.0000000000 +00:00 webauth/dist/js/bootstrap.js
21      27748 Oct 20 2014 19:16:57.0000000000 +00:00 webauth/dist/js/bootstrap.min.js
22       4096 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/img
23      98601 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/img/web_auth_background_blur.jpg
24        174 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/img/web_auth_close.png
25      30325 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/img/web_auth_onloklogo.jpg
26       5768 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/img/web_auth_onlok_logo.png
27        251 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/img/web_auth_open.png
28       4096 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/js
29       3861 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/js/affix.js
30       2582 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/js/alert.js
31       3048 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/js/button.js
32       6445 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/js/carousel.js
33       5228 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/js/collapse.js
34       4484 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/js/dropdown.js
35       2636 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/js/html5shiv.min.js
36        694 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/js/ie10-viewport-bug-workaround.js
37       6975 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/js/modal.js
38       3488 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/js/popover.js
39       4377 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/js/respond.min.js
40       4622 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/js/scrollspy.js
41       3413 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/js/tab.js
42      11908 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/js/tooltip.js
43       1964 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/js/transition.js
44       1334 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/webauth_expired.html
45       1618 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/webauth_failure.html
46       1932 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/webauth_login.html
47       1641 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/webauth_success.html
48      10445 Oct 28 2014 19:03:11.0000000000 +00:00 wnweb.tgz
49   82672260 Oct 19 2014 06:29:54.0000000000 +00:00 cat3k_caa-base.SPA.03.06.00E.pkg
50    6601404 Oct 19 2014 06:29:54.0000000000 +00:00 cat3k_caa-drivers.SPA.03.06.00E.pkg
51       1235 Oct 19 2014 06:29:59.0000000000 +00:00 packages.conf
52       1156 Oct 19 2014 06:43:36.0000000000 +00:00 vlan.dat
53   33747948 Oct 19 2014 06:29:54.0000000000 +00:00 cat3k_caa-infra.SPA.03.06.00E.pkg
54       4096 Dec 27 2013 03:17:04.0000000000 +00:00 mnt
55       4096 Dec 27 2013 03:17:04.0000000000 +00:00 mnt/images
56       4096 Dec 27 2013 03:17:09.0000000000 +00:00 mnt/images/ap.bak
57         40 Dec 05 2013 18:36:37.0000000000 +00:00 mnt/images/ap.bak/ap1g2.md5
58   11612160 Dec 05 2013 18:36:37.0000000000 +00:00 mnt/images/ap.bak/ap1g2
59         40 Dec 05 2013 18:36:37.0000000000 +00:00 mnt/images/ap.bak/ap3g1.md5
60   10475520 Dec 05 2013 18:36:38.0000000000 +00:00 mnt/images/ap.bak/ap3g1
61         40 Dec 05 2013 18:36:37.0000000000 +00:00 mnt/images/ap.bak/ap3g2.md5
62   13670400 Dec 05 2013 18:36:37.0000000000 +00:00 mnt/images/ap.bak/ap3g2
63         40 Dec 05 2013 18:36:37.0000000000 +00:00 mnt/images/ap.bak/c1140.md5
64   10321920 Dec 05 2013 18:36:37.0000000000 +00:00 mnt/images/ap.bak/c1140
65         11 Dec 05 2013 18:36:37.0000000000 +00:00 mnt/images/ap.bak/version.info
66   42769724 Oct 19 2014 06:29:54.0000000000 +00:00 cat3k_caa-iosd-universalk9.SPA.152-2.E.pkg
67       4096 Oct 19 2014 06:42:45.0000000000 +00:00 dc_profile_dir
68     169223 Oct 19 2014 06:42:45.0000000000 +00:00 dc_profile_dir/dc_default_profiles.txt
69     169223 Oct 19 2014 06:42:45.0000000000 +00:00 dc_profile_dir/dc_default_profiles.txt.bkp
70   25711500 Oct 19 2014 06:29:54.0000000000 +00:00 cat3k_caa-platform.SPA.03.06.00E.pkg
71   98462528 Oct 19 2014 06:29:55.0000000000 +00:00 cat3k_caa-wcm.SPA.10.2.102.0.pkg
1196404736 bytes available (343171072 bytes used)

Problems access to a web application (Web Interface or Web report)

Hi,
We found problems with the access to web application. Some users have problems with direct links to the web applications(Web Interface or Web reporting), when they click on the link an error message appears, the message displays the following text:
"Cannot open file Bex?sap-language=ENbsplanguge=ENcmd=idoc_TE.."
Clicking in details the message is "No Access to specified file"
For this users the access to excel reporting is correct, the message appears when they click on the direct web links through the browser or directly in BW system, but if they type the URL they can access. Other users can use the direct web link without problems.
I highly appreciate any help or idea about how to solve this issue.
Thanks in advance.

HI,
please ask to your basis that check the language of every single user on su01 tx.
This is the problem i think.
Natalia.

Unable to capture trace, when user logs in throuigh Web Interface

The Trace shows 'No Records Found', when user logs in through Web Interface of CRM. But there is Trace found, when the same user logs in through logon pad and carries out normal actvities.
sufficient auth. is provided.
Is there any setting in ST01, through which i can get trace , when user logs in through Web Interface
Regards

ST10 traces 1 instance only.
Your CRM web interface could use another instance than your backend. Go to transaction SM21, choose the appropriate server and run ST10 again.
Succes!
Kind regards,
Lodewijk Borsboom

LIST OF VALUES not Populating in BPS WEB INTERFACE ( LAYOUTS )

Hi BI Guru's
I have created a WEB interface for BPS in BI ( version 7.0) . But when i execute this in internet explorer, I do not get the LIST OF VALUES for Material.
When I click on "input help" the system open a new window for "Value selection". When I specify the material code, it gives me blank LIST OF VALUES.
But it is working for other fields like Customer, UOM in the same layout.
Please suggest some solution.
Thanks,
Nilesh Labde

hi,
Thanks for the reply.
Master data is avaliable for the Material Code. The problem is in Internet Explorer and not in SAP GUI .
If i run Planning folder for the same layou in SAP GUI it is working fine.

ASA 5505 configured for WebVPN connecting to Citrix Web Interface

ASA 5505 configured for WebVPN connecting to Citrix Web Interface.
i have a ASA 5505 that I am attempting to configure for WebVPN with passthrough into Web Interface . The user authenticates into WebVPN OK and gets the option to click on the Citrix Link (which is i add bookmark citrix server http:// 172.30.40.5.) i enter the citrix and then for example i want to open to outlook it can not open. (when i want to open some application no application is open)).there is no alarm at asa. how i solve this issue?
thanks.

Teymur,
Can you confim that after disabling the ssl/tls on the Citrix server (secure connectivity) that you are getting exactly the same error. It is possible that it is generating a different error.
The bug where we have see the existing error was CSCtf06303 but that has been fixed in 8.4.1. Can you confirm the exact version of code you are running on the ASA.
If you have confirmed the above two notes it may be adventageous to open a TAC case as we may need to do some live additional troubleshooting.
Thanks
-Jay

Distortion in Save For Web interface

I am still having problems with my Save For Web interface. Attached is a screen where you can see that with just the Optimized view showing (in this case 72%), the picture looks as expected. But if I go to 2-up or 4-up views, the 2nd image (which was the 72% Optimized) is now all pixelated as if it were a GIF.

OMG! How many years have I been using this program and I have never noticed this until now?!?
Sorry for the brain fart and thanks for pointing that out!!!
I am really having a good laugh at myself about this one!
Jules

Cisco AP 1131AG Web Interface Problem

Hello,
I purchased two Cisco access points (model AIR-AP1131AG-A-K9) from a seller on eBay. The Access Points power up fine and are able to get an IP address (I can see the AP's MAC address on my router), but it won't let me connect to the web interface to manage it. I have tried using different browsers, but they all say something along the lines of "The page could not be found" when I enter the IP address into my browser. No login screen, no nothing: just a time-out error.
When the Access Points are powered on, the Ethernet and Radio lights start out green, but then the Ethernet light stays green and the radio light flashes amber and the two alternate being lit. The status light on the outside of the Access Point goes from green to orange to red and back again, looping infinitely.
Any ideas what could be wrong? Thanks for any and all help in advance! (Please let me know if you need more information; I don't ahve the AP's with me, but I will be home in a few hours and can respond then.)

do a show cdp neighbor detail on the port the AP is connected to. Take a look at the software that is running, IOS will show k9w7, and lightweight will show k9w8.
if it''s k9w8, you'll need to convert them back to IOS
http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918
HTH,
Steve
Please remember to rate useful posts, and mark questions as answered

Displaying a BW query in web interface

Hello People ,
I am trying to see a BW query in a web interface . I will tell you how am I doing it . I run the transaction RRMX which opens an excel sheet and gives me a tol bar from which I open a query . Then I choose info areas from the next window and it shows me a tree structure with two nodes
1) Financial
2) Industry sectors
I expand industry sectors > retail > staff works
This takes me to two nodes
1)       operational
2)       sales infocube
I expand sales infocube and this takes me to a couple of nodes
1)       Key business driver
2)       Manager forcasted sales
3)       Productivity data source
4)       .
5)       .etc
I select key business driver and choose the CHANGE icon from the toolbar . This opens the query designer . There I have an icon in the toolbar which says display quey on web . I click that and it attempts to display the query in internet explorer .
Now the problem is the the message that appears on the browser is
Warning sign : variable OFPER for characterstic fiscal year/period has been converted to required entry .
Error sign : Error when generating data provider .
Now my question is what does this message mean ?Does this mean that the required content that I am trying to access has not been activated or there is some configurational issue ?
Regards
Deepak Singh

Hi Deepak,
It means that there is a selection screen for Fiscal period in which you have to enter the Fiscal Period. Only for the Fiscal period for which you entered the data would be displayed.
But the best way to create teh web report is to goto Web Application Designer -> Drag and drop the "Table" webitem on the right hand side -> Assign the Query to the web item. Now execute it in browser from the Web Application designer. Copy the link and use it whenver you want it.
Bye
Dinesh

BPS_WB-Can i add a query to a Web interface tabpage?

Dear experts,
In a BPS web interface application, i have already a tab page which allows users to input their data. Now i would like to add a second tabpage which allows to display the existing data.
Is that possible to link a BEX query to a Tabpage BPS web interface application? I would like that the query is launched and the result is displayed each time an user click on this tabpage.
Thanks in advance.

Include your query in a web template and follow the approach given in the link http://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/a861d590-0201-0010-248a-fc70d8d29f26
Edited by: Deepti Maru on Nov 30, 2010 10:24 AM

Executing the planning function while opening the web interface

hello all,
I have created a planning area based on multiprovider.This multiprovider is based on two transactional cube ie,COPA cube and Cost Center cube.
This planning area is meant for enabling integrated planning.One plans in COPA cube and other plans in Cost Center cube the income statement gets planned based on this two.
I selected planning items in multiprovider layout to display the income statement.The layout is as follows:
PlanningItem Amount
Net Sales: 9.000,00 INR (This comes from COPA)
Sales Overheads: 200,00 INR (This comes from Cost Center)
Depreciation: 200,00 INR (This comes from Cost Center)
Other Expenses: 300,00 INR (This comes from Cost Center)
EBIT: 0,00 INR
Interest Income: 0,00 INR
Interest Expense: 0,00 INR
Operating Income: 0,00 INR
Taxes: 0,00 INR
Now EBIT planning item is to be calculated from the planning items as follows:
EBIT = Net Sales-Sales Overheads-Depriciation-Other Expenses
For this i have created a planning function which calculates EBIT.This function works properly,there are no issues in it.
My problem is that i want this function to be executed as soon as i open the web interface for my planning application and the result should be as follows:
PlanningItem Amount
Net Sales: 9.000,00 INR (This comes from COPA)
Sales Overheads: 200,00 INR (This comes from Cost Center)
Depreciation: 200,00 INR (This comes from Cost Center)
Other Expenses: 300,00 INR (This comes from Cost Center)
EBIT: 8.300,00 INR
Interest Income: 0,00 INR
Interest Expense: 0,00 INR
Operating Income: 0,00 INR
Taxes: 0,00 INR
Can anybody suggest how to go about this problem?
Thanks in advance.
regards,
Yogesh

Hi Yogesh,
as far as i know, there is no standard functionality for that purpose, but there are workaround for it.
1. Modify the BSP Application.
 Go to SE80 --> Repository Browser --> BSP Application --> your WI name --> page with flow logic --> double click on page1.htm --> Event handler tabstrip --> on the drop down selection press F1 --> add a function module that call you BPS function in specific event (e.g: OnInitialization).
2. Use WI-Exit Class / WI-Extention (ABAP OO).
Here you need to create sub class from Class: CL_UPWB_BSP_APPL, and assign the class to your WI. You can then add a function module that call you BPS function in method:
2.1. Load --> performed only once on intial execution of WI.
2.2. Initialisation --> called once for each server response.
2.3. Dispatch --> called at each action and also for each WI component.
You can see further information in SAP how to paper:
How to Validate manual input in WEB planning application, New BPS-Features delivered with SAP BW 3.5, etc.
You can call your BPS function with BPS API FM (See F.Group: UPC_API)
But there is also more easier way to realize your ebit calculation. If you define your EBIT calc. manually in layout (define with manually defined Lead column). With this way, You will always get your EBIT analog with inputed values.
Then you add your EBIT calc.function to Layout Component in WI in property: 'Function After Data Change'.
Best Regards,
Suan Liono

P&L report (using web interface builder)???

Hi all,
Can someone explain BPS report concept for me?
For example,
In my P&L report, I will have fixed cost, variable cost, and revenue...etc.
I created fixed cost layout, variable cost layout, and revenue layout...etc.
My question is how those layouts generate a P&L report on the web interface??? If I enter planning data in the fixed cost layout and the values should be in the P&L report as well. How can I create P&L report in the web interface after I finished all layouts???Thank you for sharing
J.

Hi
You should create a BEX Web Query and integrate it in the upper level of WEB Layout.
Check this link for a step by step guide about this topic
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sap.km.cm.docs/library/how-to%20guides%20-%20rig%20official/bi/nw04/how%20to%20integrate%20bex%20web%20applications%20into%20bps%20web%20interfaces.doc
Ciao
Andr

How to configure the web interface of service desk

Hi All,
We are currently doing a configuration on solman service desk. I am on a stage where in i need to use the web interface of service desk via tcode notif_create_bsp. However, every time i call the transaction code (call the url) i cant view the web. Only an error the "Network Access Message: The website cannot be found".
I already activate needed services and already publish
SIAC_PUBLISH_ALL_INT but it still doesnt work.
I might have missed some configs/procedure on how to do it correctly.
My questions are.
1. How am i going to know the qualified domain name
of the Web AS for solman? How to configure it?
2. Can anyone give me some guide and any step by step documentation/procedure on this.
You help/suggestion will be very much appreciated
Thank you very much,
Ice

Hi,
+"Check the following 2 things. See if the port 8000 is open and in the url for the BSP in internet explorer, replace the host name with the IP address of your Solman server.+
+"+
That was a helpful tip. I change the host name with the ip address ofour solman server. However, upon login, it promts me to enter username and password. I've tried to login using my solman password but it shows an error like this.
Business Server Page (BSP) error
What happened?
Calling the BSP page was terminated due to an error.
SAP Note
The following error text was processed in the system:
Die URL enthält keine vollständige Domainangabe (10.123.161.125 statt 10.123.161.125.).
Exception Class CX_FQDN
Error Name
Program CX_FQDN=======================CP
Include CX_FQDN=======================CM002
ABAP Class CX_FQDN
Method CHECK
Line 10
Long text -
Error type: Exception
Your SAP Business Server Pages Team
Is there anything i need to configure so that i can maintan the username and password?
Thank you for your assistance,
Ice

How can I find out the web interface a module function is executed from?

Hello all,
I was wondering if anybody knows how would be possible de determine the web interface a function is being launched from, within the function.
I've got this function that is used for a exit variable that updates the variable value depending on another variable in a web interface. The thing is that this very same function and variable will be used in many web interfaces and the "source" variable will be different for each mask.
So, for example, mask 1 will have variable 1 as a selector variable and variable X will be updated by it. Then I also have variable 2 in mask 2 as a selector variable and variable X will be updated by it as well.
I want to develop a code, within the function module, that depending on the web interface that is calling it, it will use a source the correct variable and for this I need to know which web interface is calling the function.
I hope to have been able to explain myself clearly. It's a purely technical question.
Thanks in advance.
Best regards.

Hi Francesco,
Are you talking about that ??? )) It will explain you about to get the name of the web page when you are executing an abap function for determining the values of variables...
<a href="https://www.sdn.sap.comhttp://www.sdn.sap.comhttp://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sap.km.cm.docs/library/biw/g-i/how%20to%20make%20a%20variable%20even%20more%20flexible%20in%20bw-bps.pdf">How to make a variable even more flexible in BW-BPS?</a>
This is weird: I wrote that document a few weeks ago, it is theorically published on SDN but this is not possible to find it by using the research tool... Maybe because it applies only to BPS in 3.5. I did not have enough time to migrate that solution to BI-IP 7.0.
Regards
Laurent

My contacts are not showing up on the PC app or the web interface. Why isn't this working?

My contacts are not showing up on the PC app or the web interface. Message+ works fine on my Note 4 though. My contacts are saved in my Google account.
I've tried several things but message+ acts like there are no contacts in the app yet there are names and pictures in my conversations. Can anyone help me?

matthttam,
Let's make sure that we get you up and running with no issues. I want to make sure that we are on the same page. Are your contacts actually listed in the address book on your phone? Are you using Verizon Messages? Or the third party Messages from the Play Store? Please keep us posted.
KevinR_VZW
Follow us on Twitter @VZWSupport

SPA 502G Web interface

Similar Messages

Maybe you are looking for