SPA Reboot Reason "System 4"
Hello all,
I have a deployment of around 30 Cisco SPA504g's and 5 of them are constantly going offline. The reboot reason I get is "System 4", I have looked through all manuals and Googled extensively and cannot shed any light on this?
I have factory reset the phones and reprovisioned them, but they still constantly reboot with this reason. Any ideas?
Kind regards,
Ashley
Hi,
Not sure about this error but there was discussion before if it helps you.
https://supportforums.cisco.com/discussion/11685251/spa504g-754-and-751a-search-enterprise-directory-results-reboot-kernelerror
Thanks
Vivek
Similar Messages
-
What is the "Backup IP" reboot reason on the Cisco SPA 50x IP phones?
Hi,
We have a customer, at a remote site with SPA504G phones, they have a problem with the phones rebooting once in a while, typically once an hour.
In the reboot history on the phones the reason is "Backup IP".
I cant find any reference to this in the SPA 50x manuals or anywhere else, so what do this actually mean?
The phones are deployed using SIP, and are running firmware 7.4.9c.
The phones /admin/status.xml has this information:
< <Reboot_Reason_1>Backup IP(01/01/2003 12:00:00)</Reboot_Reason_1>
<Reboot_Reason_2>Backup IP(04/25/2012 07:43:29)</Reboot_Reason_2>
<Reboot_Reason_3>Backup IP(04/25/2012 06:40:45)</Reboot_Reason_3>
< <Reboot_Reason_4>Backup IP(04/25/2012 05:38:02)</Reboot_Reason_4>
<Reboot_Reason_5>Backup IP(04/25/2012 04:35:18)</Reboot_Reason_5>
The manual has information about several other reboot reasons, but I can't find any information about this "Backup IP" reason.
- Martin Mikkelsen, Zisson ASWrong forum, post in "Small Business voice - SPA phones". You can move your posting with the Actions panel on the right.
-
What reboot reason forces SPA perform new DHCP Discover
Hi,
I know there are different kinds of reboot reasons for the SPA-phones.(https://supportforums.cisco.com/docs/DOC-9889)
But could anyone specify what reboot reasons that makes the SPA perform a new DHCP Discovery, Request etc.?
//AnnaFreebox HD (the media box) is not configurable (at least by user). This is a device provided by Internet service provider in France. Therefore I'm not able to set static address. However, if I connect Freebox HD without Cisco SLM2008 in between it will boot okay, and if I rewire it with SLM2008 afterwards (without powering down) it will continue to work fine.
In other words, if Freebox HD got IP address it may work through cisco without the problem. However it's not possible to move Freebox HD next to the TV without unplugging it from the outlet
So the only problem as it seems is to get DHCP Discover packet through the Cisco. I have 3 SLM2008 switches in my installation. The last one was bought this year I believe, so must be still under warranty.
May be it's a good idea to swap them. However, I feel that this is not a hardware issue, but a firmware. And all of them has same firmware version 2. something...
I'll attach my traces when I get home.
Nikolai
P.S. I've just found this articles on the internet:
http://serverfault.com/questions/337591/spanning-tree-blocking-dhcp-requests-in-windows-bootp
http://www.dummies.com/how-to/content/spanning-tree-protocol-stp-and-portfast.html
Someone has similar problem with different Cisco switch. They suggest the problem is about STP. I've seen some settings about STP in my configuration pages.... -
WLC 4402 - APs last reboot reason power loss
st1\:*{behavior:url(#ieooui) }
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Normale Tabelle";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman";
mso-ansi-language:#0400;
mso-fareast-language:#0400;
mso-bidi-language:#0400;}
Hi,
we have a Wireless LAN Controller WLC 4402, Software Version 4.1.192.22M (Mesh).
At the moment there are 6 Access Points in one house, one of them is the root AP. The others are only connected via electrical socket.
AP’s are: AIR-LAP1131AG-E-K9 / Boot Version 12.3.8.0 / IOS Version 12.4(3g)JMC1
I think the configuration worked fine over a period of 2 years.
Now the problem is that the number of access points connected to the controller is changing nearly every minute. At times there is only one AP connected to the controller. So it is impossible for the clients to build up a steady connection. They have to log in via the guest user web interface at short intervals or they can’t see the wireless lan.
First we thought it would be a problem of one or two “defect” access points. But we replaced 4 of the 6 access points and the problem is still there.
An example, yesterday:
13:17 o’clock – 2 AP’s
13:19 o’clock – 4 AP’s
13:21 o’clock – 5 AP’s
13:23 o’clock – 4 AP’s
13:25 o’clock – 5 AP’s
13:25 o’clock – 4 AP’s
13:26 o’clock – 5 AP’s
13:26 o’clock – 6 AP’s
13:28 o’clock – 4 AP’s
13:28 o’clock – 2 AP’s
Eye-catching is the following message of the log, which appears often: “52 Mon May 16 13:21:56 2011 AP 'AP001d.e557.6fd8', MAC: 00:1d:70:01:bc:20 disassociated previously due to AP Reset. Last reboot reason: power loss
Also eye-catching is the AP up time. The Root AP is up for over 80 days. But all the other access points show an up time of a few minutes until some hours…but not more.
Does anybody know what the problem could be?? I read some similar threads but no solution.
In the following an abstract of the log:
21 Mon May 16 13:25:43 2011 AP 'AP0021.d847.ffca', MAC: 00:23:5e:49:9d:e0 disassociated previously due to AP Reset. Last reboot reason: power loss
22 Mon May 16 13:25:30 2011 AP Disassociated. Base Radio MAC:00:1d:70:01:b5:a0
23 Mon May 16 13:25:30 2011 AP's Interface:1(802.11a) Operation State Down: Base Radio MAC:00:1d:70:01:b5:a0 Cause=Heartbeat Timeout
24 Mon May 16 13:25:30 2011 AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:00:1d:70:01:b5:a0 Cause=Heartbeat Timeout
25 Mon May 16 13:25:05 2011 Mesh child node '00:23:5e:49:9d:ef' has changed its parent to mesh node '00:1f:ca:cc:b7:40' from mesh node '00:1d:70:01:bc:20'.
26 Mon May 16 13:24:10 2011 AP Disassociated. Base Radio MAC:00:23:5e:49:9d:e0
27 Mon May 16 13:24:10 2011 AP's Interface:1(802.11a) Operation State Down: Base Radio MAC:00:23:5e:49:9d:e0 Cause=New Discovery
28 Mon May 16 13:24:10 2011 AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:00:23:5e:49:9d:e0 Cause=New Discovery
29 Mon May 16 13:23:59 2011 AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:00:1d:71:e1:b2:20 Cause=Admin Configured
30 Mon May 16 13:23:59 2011 AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:00:1d:71:e1:b2:20 Cause=Admin Configured
31 Mon May 16 13:23:59 2011 AP's Interface:1(802.11a) Operation State Up: Base Radio MAC:00:1d:71:e1:b2:20 Cause=Admin Configured
32 Mon May 16 13:23:59 2011 AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:00:1d:71:e1:b2:20 Cause=Admin Configured
33 Mon May 16 13:23:58 2011 AP 'AP001d.45d8.4ea6', MAC: 00:1d:71:e1:b2:20 disassociated previously due to AP Reset. Last reboot reason: power loss
34 Mon May 16 13:23:31 2011 AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:00:1d:70:01:b5:a0 Cause=Admin Configured
35 Mon May 16 13:23:31 2011 AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:00:1d:70:01:b5:a0 Cause=Admin Configured
36 Mon May 16 13:23:31 2011 AP's Interface:1(802.11a) Operation State Up: Base Radio MAC:00:1d:70:01:b5:a0 Cause=Admin Configured
37 Mon May 16 13:23:31 2011 AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:00:1d:70:01:b5:a0 Cause=Admin Configured
38 Mon May 16 13:23:30 2011 AP 'AP001d.e557.6f0c', MAC: 00:1d:70:01:b5:a0 disassociated previously due to AP Reset. Last reboot reason: power loss
39 Mon May 16 13:23:13 2011 Client Association: Client MAC:00:1d:71:e1:b2:2f Base Radio MAC :00:1d:70:01:bc:20 Slot: 1 User Name:c1130-001D45D84EA6
40 Mon May 16 13:23:13 2011 Mesh child node '00:1d:71:e1:b2:2f' has changed its parent to mesh node '00:1d:70:01:bc:20' from mesh node '00:1f:ca:cc:b7:40'.
41 Mon May 16 13:23:04 2011 Mesh child node '00:1d:70:01:b5:af' has changed its parent to mesh node '00:23:5e:49:9d:e0' from mesh node '00:1f:ca:cc:b7:40'.
42 Mon May 16 13:22:57 2011 AP 'AP0021.d847.ffca', MAC: 00:23:5e:49:9d:e0 disassociated previously due to AP Reset. Last reboot reason: power loss
43 Mon May 16 13:22:39 2011 AP Disassociated. Base Radio MAC:00:23:5e:49:9d:e0
44 Mon May 16 13:22:39 2011 AP's Interface:1(802.11a) Operation State Down: Base Radio MAC:00:23:5e:49:9d:e0 Cause=New Discovery
45 Mon May 16 13:22:39 2011 AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:00:23:5e:49:9d:e0 Cause=New Discovery
46 Mon May 16 13:22:39 2011 AP 'AP0021.d847.ffca', MAC: 00:23:5e:49:9d:e0 disassociated previously due to AP Reset. Last reboot reason: power loss
47 Mon May 16 13:22:17 2011 Mesh child node '00:23:5e:49:9d:ef' has changed its parent to mesh node '00:1d:70:01:bc:20' from mesh node '00:1f:ca:cc:b7:40'.
48 Mon May 16 13:21:57 2011 AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:00:1d:70:01:bc:20 Cause=Admin Configured
49 Mon May 16 13:21:57 2011 AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:00:1d:70:01:bc:20 Cause=Admin Configured
50 Mon May 16 13:21:57 2011 AP's Interface:1(802.11a) Operation State Up: Base Radio MAC:00:1d:70:01:bc:20 Cause=Admin Configured
51 Mon May 16 13:21:57 2011 AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:00:1d:70:01:bc:20 Cause=Admin Configured
52 Mon May 16 13:21:56 2011 AP 'AP001d.e557.6fd8', MAC: 00:1d:70:01:bc:20 disassociated previously due to AP Reset. Last reboot reason: power loss
53 Mon May 16 13:21:39 2011 Client Association: Client MAC:00:23:5e:49:9d:ef Base Radio MAC :00:1f:ca:cc:b7:40 Slot: 1 User Name:c1130-0021D847FFCA
54 Mon May 16 13:21:32 2011 Client Association: Client MAC:00:23:5e:49:9d:ef Base Radio MAC :00:1f:ca:cc:b7:40 Slot: 1 User Name:c1130-0021D847FFCA
55 Mon May 16 13:21:12 2011 Mesh child node '00:1d:71:e1:b2:2f' has changed its parent to mesh node '00:1f:ca:cc:b7:40' from mesh node '00:1d:70:01:b5:a0'.
56 Mon May 16 13:21:05 2011 Client Association: Client MAC:00:1d:70:01:bc:2f Base Radio MAC :00:1f:ca:cc:b7:40 Slot: 1 User Name:c1130-001DE5576FD8
57 Mon May 16 13:20:32 2011 Mesh child node '00:23:5e:49:9d:ef' has changed its parent to mesh node '00:1f:ca:cc:b7:40' from mesh node '00:1d:70:01:bc:20'.
58 Mon May 16 13:20:11 2011 Mesh child node '00:1d:70:01:bc:2f' is no longer associated with mesh node '00:1f:ca:cc:b7:40'.
59 Mon May 16 13:20:06 2011 Mesh child node '00:1d:70:01:b5:af' has changed its parent to mesh node '00:1f:ca:cc:b7:40' from mesh node '00:1d:70:01:bc:20'.
60 Mon May 16 13:19:57 2011 AP Disassociated. Base Radio MAC:00:1d:70:01:b5:a0
61 Mon May 16 13:19:57 2011 AP's Interface:1(802.11a) Operation State Down: Base Radio MAC:00:1d:70:01:b5:a0 Cause=Heartbeat Timeout
62 Mon May 16 13:19:57 2011 AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:00:1d:70:01:b5:a0 Cause=Heartbeat Timeout
63 Mon May 16 13:19:49 2011 AP Disassociated. Base Radio MAC:00:1d:70:01:bc:20
64 Mon May 16 13:19:49 2011 AP's Interface:1(802.11a) Operation State Down: Base Radio MAC:00:1d:70:01:bc:20 Cause=Heartbeat Timeout
65 Mon May 16 13:19:49 2011 AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:00:1d:70:01:bc:20 Cause=Heartbeat Timeout
66 Mon May 16 13:19:39 2011 AP Disassociated. Base Radio MAC:00:23:5e:49:9d:e0
67 Mon May 16 13:19:39 2011 AP's Interface:1(802.11a) Operation State Down: Base Radio MAC:00:23:5e:49:9d:e0 Cause=Heartbeat Timeout
68 Mon May 16 13:19:39 2011 AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:00:23:5e:49:9d:e0 Cause=Heartbeat Timeout
69 Mon May 16 13:19:36 2011 AP Disassociated. Base Radio MAC:00:1d:71:e1:b2:20
70 Mon May 16 13:19:36 2011 AP's Interface:1(802.11a) Operation State Down: Base Radio MAC:00:1d:71:e1:b2:20 Cause=Heartbeat Timeout
71 Mon May 16 13:19:36 2011 AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:00:1d:71:e1:b2:20 Cause=Heartbeat Timeout
Greetings Lydiast1\:*{behavior:url(#ieooui) }
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Normale Tabelle";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman";
mso-ansi-language:#0400;
mso-fareast-language:#0400;
mso-bidi-language:#0400;}
Hey,
last week I tried to upgrade the controller step-by-step.
Under the software 4.1.192.35M the problem was still there… access points were often disassociated from the controller.
There were problems with Software 4.2.207.54M too. The access points couldn’t reach the download-status. The log of the access point said that it could not open the tar-file.
So I went back to 4.1.192.35M. Of course the controller lost some of its configuration. I configured it new with the same settings as before.
After it the wireless connection seemed to be a little bit more robust. I asked the users to test the connection at the weekend and this is the answer:
“so we tested the WLAN during the weekend. The situation definitely improved with respect to before. Authetication is much faster and the connection (when active) is sensibly faster.
However the connection is still very unstable and it is necessary every five-ten minutes to reconnect (especially for intense network traffic like when watching a streaming content or using VOIP applications. Actually switching off and on again the WLAN card (Airport) often a new authentication is not required. However, without doing so the connection would not resume alone to a working state.
So what to say? Better than before (thanks) but far from being fixed. From last September to January we did not experience any problem, so it must be something that chronologically happened at the beginning of the year, it is not a systemic problem.
But there were no changes or anything else at the beginning of the year.
Do you mean it makes sense to resume upgrading? I’m a little bit afraid of more problems like under 4.2.207.54M
Greetings Lydia -
i have a blinking Amber on my extreme now and it cannot extend the network. It was working fine and nothing has changed. I have restored to factory settings moved it to another room and rebooted the system without luck. Any suggestions
What OS are you running?
Please give me a screenshot of the current AE setup..
I strongly recommend if you have issues.. take control of all the variables. Apple routers have too much auto..
Here is a list that I use for setups when using Yosemite.. but it relates to any OS.
You will need to factory reset again to get going.
Factory reset universal
Power off the AE.. ie pull the power cord or power off at the wall.. wait 10sec.. hold in the reset button.. be gentle.. power on again still holding in reset.. and keep holding it in for another 10sec. You may need some help as it is hard to both hold in reset and apply power. It will show success by rapidly blinking the front led. Release the reset.. and wait a couple of min for the AE to reset and come back with factory settings. If the front LED doesn’t blink rapidly you missed it and simply try again. The reset is fairly fragile in these.. press it so you feel it just click and no more.. I have seen people bend the lever or even break it. I use a toothpick as tool.
Then redo the setup from the computer with Yosemite or whatever you are using.
1. Use very short names.. NOT APPLE RECOMMENDED names. No spaces and pure alphanumerics.
eg AEgen5 for basestation.
Use AE24ghz and AE5ghz for wireless on each band, with fixed channels as this also seems to help stop the nonsense.
2. Use all passwords that also comply but can be a bit longer. ie 8-20 characters mixed case and numbers.. no non-alphanumerics.
3. Ensure the AE always takes the same IP address.. this is not a problem for router but if the AE is bridged you can have trouble.. Try using the static IP method or control it via the main router dhcp reservations.
4. Check your share name on the computer/s is not changing.. make sure it also complies with the above.. short no spaces and pure alphanumeric..
5. Make sure IPv6 is set to link-local only in the computer. For example wireless open the network preferences, wireless and advanced / TCP/IP.. and fix the IPv6. to link-local only.
6. Set up the extend to the Express using 2.4ghz and then see how good or bad the connection is.. this is better in the old v5 utility but if you hover your mouse over where it shows connection an extra chunk of info comes up.
I have specifically used 5ghz to make the extend.. because by testing it works better.. but do not be fooled.. this good connection is poor.. the RSSI.. which is difference signal .. at -79dbm is down the bottom of the stable.. and it drops out on a daily basis.. you want to see that signal around -60dbm at min.
There is a lot more jiggery pokery you can try but the above is a good start.. if you find it still unreliable.. don't be surprised. -
All of a sudden, I go to open Adobe Photoshop Elements 10 and get this message in a box:
"DirectX is installed, but could not be initialized. Please reboot your system and relaunch Organizer."
Using Windows 7 Professional 64-bit, Office 2010 Home and Student on a Dell T3500 workstation with 3.20Ghz Xeon Processor, 12 GB Ram and a 2GB EVGA 650ti Boost graphics card.
The only thing I can think of since the last time I used PSE10 Organizer was the October, 2014 Windows updates were installed.
Any ideas anyone, Adobe seems fairly silent on this issue, and there is not much info out there on this for a Windows 7 Pro 64-bit system.
Please help.All Windows OS updates installed, all Norton Internet Security updated daily.
Went to Microsoft to try downloading DirectX just in case that was the problem, and they say you already have the newest version.
Still receive the same message. I'm at a loss, not sure what to do. -
My ipod touch died as I was rebooting the system. It won't charge?!?!
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar
It includes how to place in recovery mode -
What is the best way to reboot the system using system function in an application?
Dear Developers,
Greetings!!!!
As, i would like to reboot my WinCE 7 based system with an application. I am using one system defined function SetSystemPowerState.
Below is the sample code -
DWORD result;
result = SetSystemPowerState(NULL, POWER_STATE_BOOT,0);
if(result){
DEBUGMSG(TRUE,(TEXT("The system is going to boot\r\n")));
else{
DEBUGMSG(TRUE,(TEXT("ERROR: While trying to reboot the system :%d\r\n"),GetLastError()));
But, when I run my application I got the following debug messages -
100418 PID:4740016 TID:319004e CePerf.dll is absent - performance data will not be recorded
100422 PID:2cc0652 TID:234063a OSAXST1: >>> Loading Module 'coredll.dll' (0x9E411740) at address 0x40010000-0x40165000 in Process 'System_Reboot_DEBUG.exe' (0x9E4C379C)
100423 PID:2cc0652 TID:234063a OSAXST1: >>> Loading Module 'System_Reboot_DEBUG.exe' (0x9E4C379C) at address 0x00010000-0x00016000 in Process 'System_Reboot_DEBUG.exe' (0x9E4C379C)
PB Debugger Loaded 'System_Reboot_DEBUG.exe', no matching symbolic information found.
100435 PID:2cc0652 TID:234063a OSAXST1: >>> Loading Module 'locale.dll' (0x9E412C00) at address 0x40170000-0x401B1000 in Process 'System_Reboot_DEBUG.exe' (0x9E4C379C)
100526 PID:2cc0652 TID:234063a OSAXST1: >>> Loading Module 'normalize.dll' (0x9E412E3C) at address 0x401E0000-0x401FF000 in Process 'System_Reboot_DEBUG.exe' (0x9E4C379C)
100535 PID:2cc0652 TID:234063a CePerf.dll is absent - performance data will not be recorded
100537 PID:400002 TID:db0006 PM: DEBUGCHK failed in file d:\bt\2034\public\common\oak\drivers\pm\pdd\default\pwsdef.cpp at line 424
100538 PID:400002 TID:db0006 DefaultPowerStateManager::PlatformMapPowerStateHint: returning 2
100539 PID:2cc0652 TID:234063a The system is going to boot
100539 PID:2cc0652 TID:234063a Dll list:
100543 PID:2cc0652 TID:234063a OSAXST1: <<< Unloading Module 'coredll.dll' (0x9E411740) at address 0x40010000-0x40165000 in Process 'System_Reboot_DEBUG.exe' (0x9E4C379C)
100543 PID:2cc0652 TID:234063a OSAXST1: <<< Unloading Module 'normalize.dll' (0x9E412E3C) at address 0x401E0000-0x401FF000 in Process 'System_Reboot_DEBUG.exe' (0x9E4C379C)
100544 PID:2cc0652 TID:234063a OSAXST1: <<< Unloading Module 'locale.dll' (0x9E412C00) at address 0x40170000-0x401B1000 in Process 'System_Reboot_DEBUG.exe' (0x9E4C379C)
100545 PID:2cc0652 TID:234063a OSAXST1: <<< Unloading Module 'System_Reboot_DEBUG.exe' (0x9E4C379C) at address 0x00010000-0x00016000 in Process 'System_Reboot_DEBUG.exe' (0x9E4C379C)
PB Debugger Unloaded symbols for 'System_Reboot_DEBUG.exe'
But, the system does not boot. Any conclusion with the above observations???Using SetSystemPowerState (NULL, POWER_STATE_RESET, POWER_FORCE) will finally call the KernelLibIoControl((HANDLE)KMOD_OAL, IOCTL_HAL_REBOOT, NULL, 0, NULL, 0, NULL)
you have to implement IOCTL_HAL_REBOOT Kernel IOCTL in OAL part of your BSP.
Please mark as answer, if it is correct.
Please vote,if it is helpful post.
Vinoth.R
http://vinoth-vinothblog.blogspot.com
http://www.e-consystems.com/windowsce.asp -
I disabled my Macbook Hard Disk and lock the settings, after i try to reboot, the system wouldn't come up. It refuses to read instructions from the hard disk. How can i enable the hard disk when the system wouldn't come up?
How do you disabled it if running the same?
-
when I upgraded to 4.0 the program states "You must reboot your system to an earlier version" and it locks you out of the internet unless you have another server proxy
You can check for problems with the <b>places.sqlite</b> database file in the Firefox profile folder.
*http://kb.mozillazine.org/Bookmarks_history_and_toolbar_buttons_not_working_-_Firefox
*https://support.mozilla.org/kb/Bookmarks+not+saved#w_fix-the-bookmarks-file
*Places Maintenance: https://addons.mozilla.org/firefox/addon/places-maintenance/
You can try to restore the bookmarks from a JSON backup (bookmarks-####-##-##_xxxx_$$$$.json) in the bookmarkbackups folder.
*http://kb.mozillazine.org/Backing_up_and_restoring_bookmarks_-_Firefox
*http://kb.mozillazine.org/Lost_bookmarks
You can try to restore an older copy of the sessionstore.js file via the Time Machine if you use this.
*http://www.apple.com/support/timemachine/
*https://support.mozilla.org/kb/Recovering+important+data+from+an+old+profile
You can use this button to go to the currently used Firefox profile folder:
*Help > Troubleshooting Information > Profile Directory: Show in Finder -
My development environment is
- Model - Apap
- UI - Webdynpro for java
Do I must reboot my System to apply Apap fild that is modified or inserted something?
Now I'm, every time, reboot my system after reimport Apap model.
Reboot needs too much time.
If I not to do, web server appers 500 error.
Is there any other a manner to apply modifiy or inserted Apap filed?Hi
If you are making any changes in back end system or there is any change in rfc structure, then it is must to re-import your model.
Once you re-imported the model you need to restart your server to make the changes become effective.
To avoid following this procedure, you have another option to delete and re-build model again.But for this you have to change your application logic. You can also comment code related to model and rebuild new enhanced model and use it.(May not be recommended but for small applications it is effective)
Mandeep Virk -
I have ebook in epub format. I was using it in Windows XP. However, recently I rebooted my system to Windows 7. Now I am not able to open it in Adobe Digital Edition. It gives an error saying "Document is licensed for a different user account". Can please someone give me a solution for this. the book is expensive and i don't want to lose it. Please help.
I have ebook in epub format. I was using it in Windows XP. However, recently I rebooted my system to Windows 7. Now I am not able to open it in Adobe Digital Edition. It gives an error saying "Document is licensed for a different user account". Can please someone give me a solution for this. the book is expensive and i don't want to lose it. Please help.
-
Error when running Tomcat after reboot the system
when i first install the tomcat without reboot the system (win2k), it start the tomcat without any error message and i also able to view jsp page. but when i reboot the system and try to start tomcat i receive this kind of error message
Catalina.start: LifecycleException: null.open: java.net.BindException: Address
in use: JVM_Bind
LifecycleException: null.open: java.net.BindException: Address in use: JVM_Bin
d
at org.apache.catalina.connector.http.HttpConnector.initialize(HttpConne
ctor.java:1116)
at org.apache.catalina.core.StandardService.initialize(StandardService.j
ava:454)
at org.apache.catalina.core.StandardServer.initialize(StandardServer.jav
a:552)
at org.apache.catalina.startup.Catalina.start(Catalina.java:775)
at org.apache.catalina.startup.Catalina.execute(Catalina.java:681)
at org.apache.catalina.startup.Catalina.process(Catalina.java:179)
at java.lang.reflect.Method.invoke(Native Method)
at org.apache.catalina.startup.Bootstrap.main(Bootstrap.java:243)
----- Root Cause -----
java.net.BindException: Address in use: JVM_Bind
at java.net.PlainSocketImpl.socketBind(Native Method)
at java.net.PlainSocketImpl.bind(Unknown Source)
at java.net.ServerSocket.<init>(Unknown Source)
at java.net.ServerSocket.<init>(Unknown Source)
at org.apache.catalina.net.DefaultServerSocketFactory.createSocket(Defau
ltServerSocketFactory.java:118)
at org.apache.catalina.connector.http.HttpConnector.open(HttpConnector.j
ava:946)
at org.apache.catalina.connector.http.HttpConnector.initialize(HttpConne
ctor.java:1114)
at org.apache.catalina.core.StandardService.initialize(StandardService.j
ava:454)
at org.apache.catalina.core.StandardServer.initialize(StandardServer.jav
a:552)
at org.apache.catalina.startup.Catalina.start(Catalina.java:775)
at org.apache.catalina.startup.Catalina.execute(Catalina.java:681)
at org.apache.catalina.startup.Catalina.process(Catalina.java:179)
at java.lang.reflect.Method.invoke(Native Method)
at org.apache.catalina.startup.Bootstrap.main(Bootstrap.java:243)
i already set the JAVA_HOME and CATALINA_HOME as following:
JAVA_HOME
e:\jdk1.3.1_02\bin
CATALINA_HOME
e:\Apache Tomcat 4.0
is anyone can help me to solve this problem? thanks!Although i'm not too familiar with Tomcat, i'm pretty sure this is because something else is already using that port. Try changing the port to something different maybe?
Also, there's a possibility that Tomcat is already started as a service in win2k. Check your services for something like Apache Tomcat to see if it's starting the service automatically.
These are really just educated guesses, but worth a try maybe. -
Unable to install the GEAR driver set at this time.The GEARAspiWDM service used bz the GEAR driver set is scheduled to be deleted during the next system reboot.Please reboot the system and run iTunes again.help me..I understand this problem..thanks
Hi there, i had the exact same problem and posted a thread a few above yours, and these forums wasnt much help nobody replied, so i did a bit of research and followed all the intructions on this site: http://www.gearsoftware.com/cfknowledgebase/articledisplay.cfm?articleid=296
If you follow the steps very carefully and do as each says, this will solve your problem.. Now i am very happy i can actually install iTunes and use it for my iPod.
Remember to be carefully with the steps as the things you will be deleting are very important to your comp.
Hope this helps.
Windows XP -
I have a windows PC with windows 8.1 and have had it for 13 months. I have PE 9 installed and have been using it without a single problem when out of the blue I can't open the Organizer. I can open the editor but not the organizer. When I attempt to open it I get this...Direct x is installed but can't be initiated. Please reboot your system and then relaunch Elements organizer. Obviously, I have done this many, many times. I have had two computer experts look through my computer for a total of 13 hours and neither one of them knows what the problem is. One of them thought the issue might be bad graphics driver but the other computer guy thought that was definitely not it.
The second technician thought it was a corrupt file somewhere in the catalog. We downloaded a trial version of PE 12 and tried to open that and it won't open either. Seriously at my wits end here. I'm willing to pay to have this fixed. I've already spent hundreds of dollars to no avail. Rest of the computer works flawlessly.
We have done everything that has been posted here on this topic without success. Rebuild the thumbnail cache, repair the catalog via the catalog manager, gone in and made sure that Direct x was actually turned on...it is! I'm truly expecting a miracle as this is basically my last resort. I have over 30,000 images and just don't know what to do. Clearly installiung a new program is not the answer as PE 12 trial version came up with the same issue. HELP!!!!!!!!!!!!!!!....PLEASE!!!!!!!!!Hi,
Please try out the instructions mentioned by Vaishali in forum thread:
https://forums.adobe.com/thread/1388269?tstart=0
Thanks,
Anwesha
Maybe you are looking for
-
PLEASE HELP ME I CAN'T GO ON MY MACBOOK ANYMORE
-
EPMLCM-37009: Error parsing application artifact listing metadata. ....
This is a freshly installed 11.1.2.2 Foundation services (including CalcMgr and EPMA), RA (framework, FR and WA), Planning and Essbase are installed Only Foundation services (including CalcMgr and EPMA), RA (framework, FR and WA) are configured. OHS
-
For some reason, I can't close out any windows I have open in quicktime... i can play them and control them, but I can't close them out, or move them by clicking on the panel at the top of the window. It acts as if that panel is not part of the windo
-
Hard drive full need help moving to an external drive
i have a macbook pro with a full drive, i have 25GB of imovie events from older versions of i movie and i cant see them in the current imovie 9, how can i move them and see them in my current version?
-
Tethered Support for Nikon D-610
By reading comments herein, one is led to believe that LR 5.3 provides tethered capture support for the Nikon D-610. Well, I have a MacBook Pro and OSX, and beg to differ. I cannot, for the life of me, get LR 5.3 to recognize my D-610. If the came