SPA112 - my outgoing calls are disconnected after 30 seconds?

I have a SPA112 2 port phone adapter connected to a TP-LINK TL-WR841N. I can receive calls without problems. I can dial out, yet after 30-40 seconds into the call, I am disconnected. Can someone please help me resolve this issue. Thank you. Mike

Hard to help without informations. Please catch full syslog&debug messages
Debug and syslog Messages from SPA1x2 and SPA232D ATA (Analog Telephone Adapters)
and catch SIP messages
Installing and Using Wireshark for Capturing Network Traffic

Similar Messages

  • Video call are disconnected after 15 minutes

    Hello,
    help me pls, after 15 minutes video call disconnected every time.
    My configuration CME86 <-SIP-> CME71 <- SIP-> CUCM7.1.3.
    I perform call from caller on CME86 to callee on CUCM7.1.3.
    I collected debug logs on CME86 and see BYE message from callee on CUCM7.1.3.
    Disconnect cause CC/SIP: 16 /200.
    Thanks in advance

    Cause code 16 is normal call clearing. Does CME71 see the same BYE from CUCM7.1.3? If yes you would need SDI/SDL traces, w/ troubleshooting traces enabled, from CUCM to figure out why it dropped the call.
    Please remember to rate helpful responses and identify helpful or correct answers.

  • PAP2T Dialout disconnects after 15 seconds. Dialin Fine...???

    I have the PAP2t, I am using Gizmo5 service.
    I can get calls dialed in no problem.
    Dialing out, I get a problem  -  all calls are disconnected after 15 seconds - always the same!.  I have tried a ton of different settings and resetting to defaults, upgrading firmware...  Any ideas?
    Solved!
    Go to Solution.

    Thanks, but I just got it fixed.  Was a problem with my (dare I say?) Netgear router - WRV2000.  All the netgear's router latest firmware (from a year or more) all are incompatible.  Had to downgrade firmware to something that worked 1.1.3.9
    Now works like a charm...

  • Mail outgoing servers say they are disconnected - after an update was installed

    When I updated to Mavericks I had this problem with Gmail and a Yahoo account.  I can receive e-mail, but not send. It tells me the outgoing servers are disconnected.  Now the problem is back after an update.  I tried the 995 and 465 ports - does not work.

    Hello slesage,
    Thanks for using Apple Support Communities.
    To troubleshoot issues with Mail on your Mac please follow the steps in the article below.
    OS X Mail: Troubleshooting sending and receiving email messages
    http://support.apple.com/kb/TS3276
    Take care,
    Alex H.

  • Incomng and Outgoing calls are stop routing every five min

    Dear Team,
    Please find the attached running config and logs.Incoming and outgoing calls are landing on the gateway properly. But call stop working every five min.PRI is up and no error on controller E1.
    Please advise how to identify the issue?
    CUCM version 4.2
    debug isdn q921
    *Sep  2 08:48:21.874: ISDN Se0/0/1:15 Q921: User TX -> INFO sapi=0 tei=0, ns=2 nr=34
    *Sep  2 08:48:21.890: ISDN Se0/0/1:15 Q921: User RX <- RR sapi=0 tei=0 nr=3
    *Sep  2 08:48:21.942: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=34 nr=3
    *Sep  2 08:48:21.942: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=35
    *Sep  2 08:48:27.866: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=35 nr=3
    *Sep  2 08:48:27.866: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=36
    *Sep  2 08:48:34.322: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=36 nr=3
    *Sep  2 08:48:34.322: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=37
    *Sep  2 08:48:34.326: %ISDN-6-CONNECT: Interface Serial0/0/1:27 is now connected to 0503726912 N/A
    *Sep  2 08:48:34.326: ISDN Se0/0/1:15 Q921: User TX -> INFO sapi=0 tei=0, ns=3 nr=37
    *Sep  2 08:48:34.342: ISDN Se0/0/1:15 Q921: User RX <- RR sapi=0 tei=0 nr=4
    *Sep  2 08:48:39.694: %ISDN-6-DISCONNECT: Interface Serial0/0/1:29  disconnected from 0094777382372 , call lasted 181 seconds
    *Sep  2 08:48:39.698: ISDN Se0/0/1:15 Q921: User TX -> INFO sapi=0 tei=0, ns=4 nr=37
    *Sep  2 08:48:39.706: ISDN Se0/0/1:15 Q921: User RX <- RR sapi=0 tei=0 nr=5
    *Sep  2 08:48:39.730: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=37 nr=5
    *Sep  2 08:48:39.730: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=38
    *Sep  2 08:48:39.734: ISDN Se0/0/1:15 Q921: User TX -> INFO sapi=0 tei=0, ns=5 nr=38
    *Sep  2 08:48:39.746: ISDN Se0/0/1:15 Q921: User RX <- RR sapi=0 voice-port 0/1/2
    *Sep  2 08:48:49.746: ISDN Se0/0/1:15 Q921: User TX -> RRp sapi=0 tei=0 nr=38
    *Sep  2 08:48:49.758: ISDN Se0/0/1:15 Q921: User RX <- RRf sapi=0 tei=0 nrsh
    *Sep  2 08:48:59.762: ISDN Se0/0/1:15 Q921: User TX -> RRp sapi=0 tei=0 nr=38
    *Sep  2 08:48:59.766: ISDN Se0/0/1:15 Q921: User RX <- RRf sapi=0 tei=0 nr
    *Sep  2 08:49:01.946: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=38 nr=6
    *Sep  2 08:49:01.950: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=39
    *Sep  2 08:49:01.950: %ISDN-6-DISCONNECT: Interface Serial0/0/1:27  disconnected from 0503726912 , call lasted 27 seconds
    Voice-Gw#
    Voice-Gw#
    Voice-Gw#
    Voice-Gw#
    *Sep  2 08:49:01.954: ISDN Se0/0/1:15 Q921: User TX -> INFO sapi=0 tei=0, ns=6 nr=39
    *Sep  2 08:49:01.962: ISDN Se0/0/1:15 Q921: User RX <- RR sapi=0 tei=0 nr=7
    *Sep  2 08:49:02.034: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=39 nr=7
    *Sep  2 08:49:02.034: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=40
    controller E1 0/0/1
     pri-group timeslots 1-31
    interface Serial0/0/1:15
     no ip address
     encapsulation hdlc
     isdn switch-type primary-net5
     isdn incoming-voice voice
     no cdp enable
    =======================
    Voice-Gw#
    *Sep  2 08:55:25.214: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=71 nr=27
    *Sep  2 08:55:25.214: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=72
    *Sep  2 08:55:25.234: ISDN Se0/0/1:15 Q921: User TX -> INFO sapi=0 tei=0, ns=27 nr=72
    *Sep  2 08:55:25.246: ISDN Se0/0/1:15 Q921: User TX -> INFO sapi=0 tei=0, ns=28 nr=72
    *Sep  2 08:55:25.250: ISDN Se0/0/1:15 Q921: User RX <- RR sapi=0 tei=0 nr=28
    *Sep  2 08:55:25.258: ISDN Se0/0/1:15 Q921: User RX <- RR sapi=0 tei=0 nr=29
    *Sep  2 08:55:27.518: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=72 nr=29
    *Sep  2 08:55:27.518: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=73
    *Sep  2 08:55:27.522: ISDN Se0/0/1:15 Q921: User TX -> INFO sapi=0 tei=0, ns=29 nr=73
    *Sep  2 08:55:27.534: ISDN Se0/0/1:15 Q921: User RX <- RR sapi=0 tei=0 nr=30
    *Sep  2 08:55:27.546: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=73 nr=30
    *Sep  2 08:55:27.546: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=74
    *Sep  2 08:55:33.318: ISDN Se0/0/1:15 Q921: User TX -> INFO sapi=0 tei=0, ns=30 nr=74
    *Sep  2 08:55:33.330: ISDN Se0/0/1:15 Q921: User RX <- RR sapi=0 tei=0 nr=31
    *Sep  2 08:55:33.390: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=74 nr=31
    *Sep  2 08:55:33.394: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=75
    *Sep  2 08:55:37.190: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=75 nr=31
    *Sep  2 08:55:37.194: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=76
    *Sep  2 08:55:38.534: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=76 nr=31
    *Sep  2 08:55:38.534: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=77
    *Sep  2 08:55:38.538: %ISDN-6-CONNECT: Interface Serial0/0/1:27 is now connected to 0504312690 N/A
    *Sep  2 08:55:38.538: ISDN Se0/0/1:15 Q921: User TX -> INFO sapi=0 tei=0, ns=31 nr=77
    *Sep  2 08:55:38.554: ISDN Se0/0/1:15 Q921: User RX <- RR sapi=0 tei=0 nr=32
    *Sep  2 08:55:42.542: ISDN Se0/0/1:15 Q921: User TX -> INFO sapi=0 tei=0, ns=32 nr=77
    *Sep  2 08:55:42.554: ISDN Se0/0/1:15 Q921: User RX <- RR sapi=0 tei=0 nr=33
    *Sep  2 08:55:42.606: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=77 nr=33
    *Sep  2 08:55:42.606: ISDN Se0/0/1:15 Q921: User TX -> RR sapi=0 tei=0 nr=78
    *Sep  2 08:55:46.766: ISDN Se0/0/1:15 Q921: User RX <- INFO sapi=0 tei=0, ns=78 nr=3
    % Invalid input detected at '^' marker.
    Voice-Gw#sh controllers e1 0/0/1
    E1 0/0/1 is up.
      Applique type is Channelized E1 - balanced
      No alarms detected.
      alarm-trigger is not set
      Version info Firmware: 20060711, FPGA: 13, spm_count = 0
      Framing is CRC4, Line Code is HDB3, Clock Source is Line.
      CRC Threshold is 320. Reported from firmware  is 320.
      Data in current interval (99 seconds elapsed):
         0 Line Code Violations, 0 Path Code Violations
         0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
         0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
    Voice-Gw#
    Voice-Gw(config)#do sh isdn statu
    Global ISDN Switchtype = primary-net5
    ISDN Serial0/0/0:15 interface
            dsl 0, interface ISDN Switchtype = primary-net5
        Layer 1 Status:
            DEACTIVATED
        Layer 2 Status:
            TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
        Layer 3 Status:
            0 Active Layer 3 Call(s)
        Active dsl 0 CCBs = 0
        The Free Channel Mask:  0x00000000
        Number of L2 Discards = 0, L2 Session ID = 0
    ISDN Serial0/0/1:15 interface
            dsl 1, interface ISDN Switchtype = primary-net5
        Layer 1 Status:
            ACTIVE
        Layer 2 Status:
            TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
        Layer 3 Status:
            3 Active Layer 3 Call(s)
            CCB:callid=E3C0, sapi=0, ces=0, B-chan=30, calltype=VOICE
            CCB:callid=E3C6, sapi=0, ces=0, B-chan=31, calltype=VOICE
            CCB:callid=E3CB, sapi=0, ces=0, B-chan=29, calltype=VOICE
        Active dsl 1 CCBs = 3
        The Free Channel Mask:  0x8FFF7FFF
        Number of L2 Discards = 0, L2 Session ID = 2
        Total Allocated ISDN CCBs = 3

    Hi.
    Can you please also attach a CUCM trace during a disconnected call?
    Thanks
    Regards
    Carlo

  • My outgoing calls are blocked from Southern Ireland how to unblock

    My outgoing calls are blocked from irelandneed to unblock them

    Hi ,
    Welcome to the community.
    What phone are you using?
    What network are you on EE/T-Mobile/Orange?
    And last question are you on contract?
    If you could reply with this, I will try andf get you sorted to make calls in Ireland .
    Thank you.

  • My outgoing calls are block, how do I correct this?

    My outgoing calls are blocked, how do I correct this on my 4S?

    Settings > Phone > Show My Caller ID > Show My Caller ID > On.

  • Blank login screen on the iPad keeps popping up and wifi disconnecting after 20 seconds

    hi, we have an ipad running IOS 5 that keeps having a blank login screen on the iPad keeps popping up and wifi disconnecting after 20 seconds. 
    I am yet to find out why this is, any clues?  (note that both apple.com and facebook are blocked at the router, but nothing else)...

    actually we cannot due to policy reasons... it appears through testing that the iPad is phoning home and sending private data to Apple regardless, it is also odd they placed these PRIVACY settings in About hidden away so that no-one knows they are there.
    From the iPad homescreen, tap on Settings > General > About
    Tap on "Diagnostics & Usage" > select "Don't Send"
    So... anyone else know why if we block Apple, the iPad disconnects from the internet via Wifi?

  • Calling a method after 10 seconds

    Hello,
    I need to call a method after 10 seconds. That is to make sure that if one particular field is updated, say 3 times in a window of 10 seconds, I should just be able to take the last value and process it, in my ajax app. I am so far using the Timer class, but the problem is, it ticks off a thread for every single request to be processed after 10 seconds and processes all the 3 requests, where as I should just be running that method once for the last request. Could you please help me with this ?
    Cant do this at the client level, for the page may be closed within those 10 seconds of the event and the setTimeout wont work then.
    This is what I made so far.:
    final Map<String, Object> mp = new HashMap<String, Object>();
    if(form.getEmpId() != null )
                mp.put(form.getEmpId().toString(), form);
                new java.util.Timer().schedule(new java.util.TimerTask()
                   public void run()
                      EmpForm form1 = (EmpForm)mp.get(empId.toString());
                      String empId = form1.getempId().toString();
                      String value1Changed = form1.getValue1Changed().toString();
                      String value2Changed = form1.getValue2Changed().toString();
                      myService.changeData(empId, value1Changed, value2Changed),
                }, 10000);
             }

    Thanks for replying
    tjacobs01 wrote:
    My recommendation is that you share an AtomicReference between your timer and the listener that is receiving the updates. This way, the listener can just update the value, and the timer uses the latest one when it wakes upOk, out of my limited understanding, I looked up AtmoicReference and found it a class. I think I cant use that since I am maintaining a list of empIds against the object that holds their data in a hashmap, expecting the map to override the empId on the second request. So, I made a final map and thought Id just push the timer scheduler method in another method, but the problem is, for me to ask that thread (which I expect to run after 10 seconds of my calling) to run, I need to call it somewhere, and as soon as I get a request I am calling the method which runs/ticks off the thread.
    I was thinking that since I am passing and using a final map (that I declared as a class level variable), I will be able to put update the map object and whenever the thread runs, will fetch the latest value (of the empId) in the map. But I guess I am doing it wrong. :(

  • Skype account keeps disconnecting after 30 seconds

    hi guys,
    its driving me nuts.  my skype account keeps disconnecting after 30 seconds and i haven't even done anything.  it does it on windows, and on my iphone too.
    what's going on? is this a problem with skype?  i've seen similar posts. and i'm using skype 6.20

    That generally means there is an issue with your Microsoft account.  You may have to verify some settings in your account to make sure a configuration isn't causing it.  The only solution I'm aware of is temporarily unlinking your account.  I do not know if reconnecting it will resolve the issue right away.
    https://support.skype.com/en/faq/FA12211/

  • Hi.. I got some problem  when i want to type something , letters are not displaying immediately , they are displaying after some seconds. can you help me out

    Hi.. I got some problem  when i want to type something , letters are not displaying immediately , they are displaying after some seconds. can you help me out

    Hello:
    I am not being critical, but you seem to want Safari to behave exactly like Chrome.  Every software developer has a plan.  Sometimes features in one product parallel other products - sometime not.  There might be some things available that would help you.  Do not hold your breath, however, for suggestions from people who use these forums.  Most of us use (and like) Apple products.  If you wish to make suggestions for future improvements, there is a feedback area on this web site that Apple employees read/review.
    Candidly, your approach would be akin to suggesting that Apple emulate the "features" in Windows (heaven forbid).
    I use Safari (and have for years).  I use Firefox (not a bad product) as my alternate browser.
    Sorry for what appears to be a pedantic lecture.  However, I think most of us adapt to different products if we really want to use them.
    Barry
    Message was edited by: Barry Hemphill

  • Help me! After updating my iphone 3g is no longer able to call. Outgoing calls are completely silent for the recipient

    Help me! After updating my iphone 3g is no longer able to call!!
    Outgoing calls can be made ​​but the recipient does not feel anything. I own a phone that is useless!

    First try Resetting it: Hold down the home and sleep button, ignore the red OFF slider, wait for the Apple logo then let go.
    If that does not work, Restore your iPhone in iTunes from your backup.
    If that still does not fix it, Restore your iPhone and a new phone (not from backup) and see how it works. If it is doing fine you have a app you are using that is probably causing your problem. Load them one and a time until the problems recur and you will have found the one that is a problem.

  • Call gets disconnected after playing the menu from CVP

    Hello,
    When I make a call, the call is going to the ICM and then it is coming to the Call server then to the VXML gateway and then it goes to the VXML server and plays the promt.
    The problem i am facing is that once the menu audio is played the call gets disconnected.  It doesnt let me choose any options. I feel it is not able to identify the my inputs
    I have some debug outputs
    Mar  1 01:09:03.095: //-1/C113522D805A/CCAPI/cc_api_display_ie_subfields:
       cc_api_call_setup_ind_common:
       cisco-username=1000
       ----- ccCallInfo IE subfields -----
       cisco-ani=sip:[email protected]:5060
       cisco-anitype=0
       cisco-aniplan=0
       cisco-anipi=0
       cisco-anisi=1
       dest=sip:[email protected];transport=udp
       cisco-desttype=0
       cisco-destplan=0
       cisco-rdie=FFFFFFFF
       cisco-rdn=
       cisco-rdntype=0
       cisco-rdnplan=0
       cisco-rdnpi=-1
       cisco-rdnsi=-1
       cisco-redirectreason=-1   fwd_final_type =0
       final_redirectNumber =
       hunt_group_timeout =0
    *Mar  1 01:09:03.103: //-1/C113522D805A/CCAPI/cc_api_call_setup_ind_common:
       Interface=0x67213130, Call Info(
       Calling Number=sip:[email protected]:5060,(Calling Name=)(TON=Unknown, NPI=Unknown, Screening=User, Passed, Presentation=Allowed),
       Called Number=sip:[email protected];transport=udp(TON=Unknown, NPI=Unknown),
       Calling Translated=FALSE, Subscriber Type Str=Un
    R1#known, FinalDestinationFlag=TRUE,
       Incoming Dial-peer=811, Progress Indication=NULL(0), Calling IE Present=TRUE,
       Source Trkgrp Route Label=, Target Trkgrp Route Label=, CLID Transparent=FALSE), Call Id=65
    *Mar  1 01:09:03.103: //-1/C113522D805A/CCAPI/ccCheckClipClir:
       In: Calling Number=sip:[email protected]:5060(TON=Unknown, NPI=Unknown, Screening=User, Passed, Presentation=Allowed)
    *Mar  1 01:09:03.103: //-1/C113522D805A/CCAPI/ccCheckClipClir:
       Out: Calling Number=sip:[email protected]:5060(TON=Unknown, NPI=Unknown, Screening=User, Passed, Presentation=Allowed)
    *Mar  1 01:09:03.103: //-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
    *Mar  1 01:09:03.103: :cc_get_feature_vsa malloc success
    *Mar  1 01:09:03.103: //-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
    *Mar  1 01:09:03.103:  cc_get_feature_vsa count is 1
    *Mar  1 01:09:03.103: //-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
    *Mar  1 01:09:03.103: :FEATURE_VSA attributes are: feature_name:0,feature_time:1732532552,feature_id:23
    *Mar  1 01:09:03.103: //65/C113522D805A/CCAPI/cc_api_call_setup_ind_common:
       Set Up Event Sent;
       Call Info(Calling Number=(TON=Unknown, NPI=Unknown, Screening=User, Passed, Presentation=Allowed),
       Called Number=(TON=Unknown, NPI=Unknown))
    *Mar  1 01:09:03.111: //65/C113522D805A/CCAPI/cc_process_call_setup_ind:
       Event=0x67452800
    *Mar  1 01:09:03.119: //65/C113522D805A/CCAPI/ccCallSetContext:
       Context=0x65097114
    *Mar  1 01:09:03.119: //65/C113522D805A/CCAPI/cc_process_call_setup_ind:
       >>>>CCAPI handed cid 65 with tag 811 to app "_ManagedAppProcess_bootstrap"
    *Mar  1 01:09:03.143: //65/C113522D805A/CCAPI/ccCallProceeding:
       Progress Indication=NULL(0)
    *Mar  1 01:09:03.147: //65/C113522D805A/CCAPI/ccCallConnect:
       Progress Indication=NULL(0), Data Bitmask=0x0
    *Mar  1 01:09:03.151: //65/C113522D805A/CCAPI/ccCallConnect:
       Call Entry(Connected=TRUE, Responsed=TRUE)
    *Mar  1 01:09:03.239: //65/C113522D805A/CCAPI/cc_api_event_indication:
       Event=141, Call Id=65
    *Mar  1 01:09:03.243: //65/C113522D805A/CCAPI/cc_api_event_indication:
       Event Is Sent To Conferenced SPI(s) Directly
    *Mar  1 01:09:03.243: //65/C113522D805A/CCAPI/cc_api_caps_ind:
       Destination Interface=0x0, Destination Call Id=-1, Source Call Id=65,
       Caps(Codec=0x0, Fax Rate=0x2, Vad=0x2,
       Modem=0x0, Codec Bytes=20, Signal Type=2)
    *Mar  1 01:09:03.243: //65/C113522D805A/CCAPI/cc_api_caps_ind:
       Caps(Playout Mode=1, Playout Initial=60(ms), Playout Min=40(ms),
       Playout Max=250(ms), Fax Nom=300(ms))
    *Mar  1 01:09:04.163: //65/C113522D805A/CCAPI/ccCallHandoff:
       Silent=FALSE, Application=0x6773AB4C, Conference Id=0xFFFFFFFF
    *Mar  1 01:09:04.295: //65/C113522D805A/CCAPI/ccSetDigitTimeouts:
       Initial Digit Timeout=0(ms), Inter Digit Timeout=0(ms)
    *Mar  1 01:09:04.295: //65/C113522D805A/CCAPI/ccSetDigitTimeouts:
       Call Entry(Inter Digit Timeout=0(ms), Initial Digit Timeout=0(ms))
    *Mar  1 01:09:04.295: //65/xxxxxxxxxxxx/CCAPI/ccCallReportDigits:
       (callID=0x41, digit_event=0x1, enable=TRUE, consume=FALSE)
    *Mar  1 01:09:04.299: //65/C113522D805A/CCAPI/ccCallReportDigits:
       Enabled=TRUE, Call Id=65
    *Mar  1 01:09:04.303: //65/xxxxxxxxxxxx/CCAPI/cc_api_call_report_digits_done:
       (vdbPtr=0x67213130, callID=0x41, disp=-4, digit_event=0x1, enable=TRUE, consume=FALSE)
    *Mar  1 01:09:04.307: //65/C113522D805A/CCAPI/cc_api_call_report_digits_done:
       Enabled=TRUE, Disposition=0xFFFFFFFC, Interface=0x67213130, Call Id=65
    *Mar  1 01:09:04.311: //65/C113522D805A/CCAPI/cc_api_call_report_digits_done:
       Call Entry(Initial Digit Timeout=0(ms), Inter Digit Timeout=0(ms))
    *Mar  1 01:09:05.291: //65/C113522D805A/CCAPI/ccAssociateStream:
       Coder=5, DTMF Relay=4, Vad=0,
       Record Function=0x0, Event Queue=0x66954714, Stream Context=678B0364,
       Record Context=0x0, Stream Call Id=66, Call Id=65
    *Mar  1 01:09:05.295: //65/C113522D805A/CCAPI/ccAssociateStream:
       Call Entry(Stream Status=2, Digit Enable=TRUE)
    *Mar  1 01:09:05.327: //65/C113522D805A/CCAPI/cc_api_call_associated:
       Interface=0x0, CallId=65, Disposition=0
       Play Function=0x62C2DFA8, Codec=0x5, Vad=0x0
       Media Type=0x3, SPI Context=0x678D2480, Stream CallId=66
       TX Dynamic Pt=0x0, RX Dynamic Pt=0x0
    *Mar  1 01:09:05.531: //65/C113522D805A/CCAPI/ccSetDigitTimeouts:
       Initial Digit Timeout=5000(ms), Inter Digit Timeout=10000(ms)
    *Mar  1 01:09:05.535: //65/C113522D805A/CCAPI/ccSetDigitTimeouts:
       Call Entry(Inter Digit Timeout=10000(ms), Initial Digit Timeout=5000(ms))
    *Mar  1 01:09:05.535: //65/xxxxxxxxxxxx/CCAPI/ccCallReportDigits:
       (callID=0x41, digit_event=0x1, enable=TRUE, consume=FALSE)
    *Mar  1 01:09:05.535: //65/C113522D805A/CCAPI/ccCallReportDigits:
       Enabled=TRUE, Call Id=65
    *Mar  1 01:09:05.535: //65/xxxxxxxxxxxx/CCAPI/cc_api_call_report_digits_done:
       (vdbPtr=0x67213130, callID=0x41, disp=-4, digit_event=0x1, enable=TRUE, consume=FALSE)
    *Mar  1 01:09:05.539: //65/C113522D805A/CCAPI/cc_api_call_report_digits_done:
       Enabled=TRUE, Disposition=0xFFFFFFFC, Interface=0x67213130, Call Id=65
    *Mar  1 01:09:05.543: //65/C113522D805A/CCAPI/cc_api_call_report_digits_done:
       Call Entry(Initial Digit Timeout=5000(ms), Inter Digit Timeout=10000(ms))
    *Mar  1 01:09:08.723: //65/C113522D805A/CCAPI/ccDisassociateStream:
       Record Context=0x0, Stream Call Id=66, Call Id=65
    *Mar  1 01:09:08.723: //65/C113522D805A/CCAPI/ccDisassociateStream:
       Call Entry(Stream Status=1, Digit Enable=TRUE)
    *Mar  1 01:09:08.735: //65/C113522D805A/CCAPI/ccAssociateStream:
       Coder=5, DTMF Relay=4, Vad=0,
       Record Function=0x0, Event Queue=0x66954714, Stream Context=678B0364,
       Record Context=0x0, Stream Call Id=66, Call Id=65
    *Mar  1 01:09:08.739: //65/C113522D805A/CCAPI/ccAssociateStream:
       Call Entry(Stream Status=2, Digit Enable=TRUE)
    *Mar  1 01:09:08.747: //65/C113522D805A/CCAPI/cc_api_call_associated:
       Interface=0x0, CallId=65, Disposition=0
       Play Function=0x62C2DFA8, Codec=0x5, Vad=0x0
       Media Type=0x3, SPI Context=0x678D2480, Stream CallId=66
       TX Dynamic Pt=0x0, RX Dynamic Pt=0x0
    R1#
    R1#
    *Mar  1 01:09:16.143: //65/C113522D805A/CCAPI/ccDisassociateStream:
       Record Context=0x0, Stream Call Id=66, Call Id=65
    *Mar  1 01:09:16.143: //65/C113522D805A/CCAPI/ccDisassociateStream:
       Call Entry(Stream Status=1, Digit Enable=TRUE)
    *Mar  1 01:09:16.175: //65/C113522D805A/CCAPI/ccCallDisconnect:
       Cause Value=16, Tag=0x0, Call Entry(Previous Disconnect Cause=0, Disconnect Cause=0)
    *Mar  1 01:09:16.179: //65/C113522D805A/CCAPI/ccCallDisconnect:
       Cause Value=16, Call Entry(Responsed=TRUE, Cause Value=16)
    *Mar  1 01:09:16.227: //65/C113522D805A/CCAPI/cc_api_call_disconnect_done:
    R1#Disposition=0, Interface=0x67213130, Tag=0x0, Call Id=65,
       Call Entry(Disconnect Cause=16, Voice Class Cause Code=0, Retry Count=0)
    *Mar  1 01:09:16.235: //65/C113522D805A/CCAPI/cc_api_call_disconnect_done:
       Call Disconnect Event Sent
    *Mar  1 01:09:16.235: //-1/xxxxxxxxxxxx/CCAPI/cc_free_feature_vsa:
    *Mar  1 01:09:16.235: :cc_free_feature_vsa freeing 67445940
    *Mar  1 01:09:16.235: //-1/xxxxxxxxxxxx/CCAPI/cc_free_feature_vsa:
    *Mar  1 01:09:16.235:  vsacount in free is 0
    I have some  basic VXML gateway configuration
    R1#show run
    Building configuration...
    Current configuration : 2588 bytes
    version 12.4
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname R1
    boot-start-marker
    boot-end-marker
    no aaa new-model
    memory-size iomem 5
    ip cef
    no ip domain lookup
    ip domain name lab.local
    ip auth-proxy max-nodata-conns 3
    ip admission max-nodata-conns 3
    multilink bundle-name authenticated
    voice service voip
    sip
      header-passing
    application
      service cvperror flash:cvperror.tcl
      paramspace english index 0
      paramspace english language en
      paramspace english location flash
      paramspace english prefix en
      service new-call flash:bootstrap.vxml
      paramspace english index 0
      paramspace english language en
      paramspace english location flash
      paramspace english prefix en
      service ringtone flash:ringtone.tcl
      paramspace english language en
      paramspace english index 0
      paramspace english location flash
      paramspace english prefix en
      service ringback flash:ringtone.tcl
      service handoff flash:handoff.tcl
      paramspace english index 0
      paramspace english language en
      paramspace english location flash
      paramspace english prefix en
      service bootstrap flash:bootstrap.tcl
      paramspace english index 0
      paramspace english language en
      paramspace english location flash
      paramspace english prefix en
    archive
    log config
      hidekeys
    interface FastEthernet0/0
    ip address 192.168.1.253 255.255.255.0
    duplex auto
    speed auto
    interface FastEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    ip forward-protocol nd
    no ip http server
    no ip http secure-server
    control-plane
    dial-peer voice 9191 voip
    service ringtone
    session protocol sipv2
    incoming called-number 91919191
    codec g711ulaw
    no vad
    dial-peer voice 9292 voip
    service cvperror
    session protocol sipv2
    incoming called-number 92929292
    codec g711ulaw
    no vad
    dial-peer voice 1503 voip
    destination-pattern 1503
    session protocol sipv2
    session target ipv4:192.168.1.57
    dtmf-relay rtp-nte h245-alphanumeric h245-signal
    codec g711ulaw
    ip qos dscp cs3 signaling
    no vad
    dial-peer voice 100 voip
    destination-pattern 10..
    session target ipv4:192.168.1.100
    dial-peer voice 811 voip
    service bootstrap
    session protocol sipv2
    session target sip-server
    incoming called-number 81T
    codec g711ulaw
    no vad
    line con 0
    exec-timeout 0 0
    privilege level 15
    logging synchronous
    line aux 0
    exec-timeout 0 0
    privilege level 15
    logging synchronous
    line vty 0 4
    login
    end
    Please help me out how o fix this issue/

    Thanks for the respose
    The microapp what I use is user.microapp.ToExtVXML[]
    This is the activity log in the CVP application. I dont see any error logs.
    192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.109,,start,newcall,
    192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.109,,start,ani,NA
    192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.109,,start,areacode,NA
    192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.109,,start,exchange,NA
    192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.109,,start,dnis,NA
    192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.109,,start,uui,NA
    192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.109,,start,iidigits,NA
    192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.125,CVP Subdialog Start_01,enter,
    192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.593,CVP Subdialog Start_01,exit,done
    192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.593,Greetings,enter,
    192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.597,Greetings,interaction,audio_group,initial_audio_group
    192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.703,Greetings,exit,done
    192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.703,Menu,enter,
    192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.707,Menu,interaction,audio_group,initial_audio_group
    192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.875,Menu,exit,
    192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.875,,end,how,hangup
    192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.875,,end,result,normal
    192.168.1.57.1368611401109.0.ImationIVR,05/15/2013 15:20:01.875,,end,duration,1
    192.168.1.57.1368611406531.1.ImationIVR,05/15/2013 15:20:06.531,,start,newcall,
    192.168.1.57.1368611406531.1.ImationIVR,05/15/2013 15:20:06.531,,start,ani,NA
    192.168.1.57.1368611406531.1.ImationIVR,05/15/2013 15:20:06.531,,start,areacode,NA
    192.168.1.57.1368611406531.1.ImationIVR,05/15/2013 15:20:06.531,,start,exchange,NA
    192.168.1.57.1368611406531.1.ImationIVR,05/15/2013 15:20:06.531,,start,dnis,NA
    192.168.1.57.1368611406531.1.ImationIVR,05/15/2013 15:20:06.531,,start,uui,NA
    192.168.1.57.1368611406531.1.ImationIVR,05/15/2013 15:20:06.531,,start,iidigits,NA
    192.168.1.57.1368611406531.1.ImationIVR,05/15/2013 15:20:06.531,CVP Subdialog Start_01,enter,
    192.168.1.57.1368611406531.1.ImationIVR,05/15/2013 15:20:06.921,CVP Subdialog Start_01,exit,done
    192.168.1.57.1368611406531.1.ImationIVR,05/15/2013 15:20:06.921,Greetings,enter,
    192.168.1.57.1368611406531.1.ImationIVR,05/15/2013 15:20:06.957,Greetings,interaction,audio_group,initial_audio_group
    192.168.1.57.1368611406531.1.ImationIVR,05/15/2013 15:20:07.109,Greetings,exit,done
    192.168.1.57.1368611406531.1.ImationIVR,05/15/2013 15:20:07.109,Menu,enter,
    192.168.1.57.1368611406531.1.ImationIVR,05/15/2013 15:50:25.718,,end,how,app_session_complete
    192.168.1.57.1368611406531.1.ImationIVR,05/15/2013 15:50:25.718,,end,result,timeout
    192.168.1.57.1368611406531.1.ImationIVR,05/15/2013 15:50:25.718,,end,duration,1819
    192.168.1.57.1368611576312.2.ImationIVR,05/15/2013 15:22:56.312,,start,newcall,
    192.168.1.57.1368611576312.2.ImationIVR,05/15/2013 15:22:56.312,,start,ani,NA
    192.168.1.57.1368611576312.2.ImationIVR,05/15/2013 15:22:56.312,,start,areacode,NA
    192.168.1.57.1368611576312.2.ImationIVR,05/15/2013 15:22:56.312,,start,exchange,NA
    192.168.1.57.1368611576312.2.ImationIVR,05/15/2013 15:22:56.312,,start,dnis,NA
    192.168.1.57.1368611576312.2.ImationIVR,05/15/2013 15:22:56.312,,start,uui,NA
    192.168.1.57.1368611576312.2.ImationIVR,05/15/2013 15:22:56.312,,start,iidigits,NA
    192.168.1.57.1368611576312.2.ImationIVR,05/15/2013 15:22:56.312,CVP Subdialog Start_01,enter,
    192.168.1.57.1368611576312.2.ImationIVR,05/15/2013 15:22:56.750,CVP Subdialog Start_01,exit,done
    192.168.1.57.1368611576312.2.ImationIVR,05/15/2013 15:22:56.750,Greetings,enter,
    192.168.1.57.1368611576312.2.ImationIVR,05/15/2013 15:22:56.782,Greetings,interaction,audio_group,initial_audio_group
    192.168.1.57.1368611576312.2.ImationIVR,05/15/2013 15:22:56.937,Greetings,exit,done
    192.168.1.57.1368611576312.2.ImationIVR,05/15/2013 15:22:56.937,Menu,enter,
    192.168.1.57.1368611576312.2.ImationIVR,05/15/2013 15:53:25.718,,end,how,app_session_complete
    192.168.1.57.1368611576312.2.ImationIVR,05/15/2013 15:53:25.718,,end,result,timeout
    192.168.1.57.1368611576312.2.ImationIVR,05/15/2013 15:53:25.718,,end,duration,1829
    Thank you

  • Call is disconnected after being transferred by the AA SPA 400

    I have 2 groups set up in the AA to transfer to different groups ie "Accounts" or "Production". These all worked originally, but now they seem to have stopped working. Callers dial in and press "13" as per the prompts, then the AA message tells them to wait while the call is transferred, and then the call is disconnected.
    This only happens for one of the prompts, the other one is fine. As i said this all worked fine originall, and no settings have been changed.....
    Any ideas / help / suggestions greatly appreciated.
    System is SPA9000, SPA400, SPA942 x 3

    After having searched through this and a number of other forums I am amazed that no one has come across and understands the true reason this is happening.  The other posts do offer some insight and good suggestions but no one has realized the true underlying problem.  Apparently the AA, no mater what dial plan you use, will forward any partially dialed portion of the numbers that match the list.  So even if you specifically limit the acceptable numbers to only the extensions on your system you can still get a partial result passed on from the AA which does not have a valid extension on your system.
    For Example:
    DP1 = (120|102|103|152|100|9|<0:100>|<*8:vmm4>)
    AA Script 1 =
    <aa>
    <form id="dt" type="menu"><audio src="prompt5" bargein="T"/><noinput timeout="5" repeat="T"/><dialplan src="dp1"/>
    <nomatch repeat="F"><audio src="prompt3" bargein="T"/></nomatch>
    <match><case input="9"><audio src="prompt8" bargein="F"/></case>
    <default><audio src="prompt2"/><xfer name="ext" target="$input"/></default>
    </match>
    </form>
    </aa>
    You would think this would be sufficient to limit inbound calls to just the extensions listed in the dial plan.  Not so.  The caller can dial any part of the listed extensions (1,10,12,15,*...) and the call will still be transferred and subsequently dropped.  I tried every possible combination of dial plan settings including specifically rejecting (which you should not have to do) everything other then the desired combinations.  Problem is if you try to reject any subset of the valid combinations it interferes with them and they get rejected to.  The real problem here is in that how the dial plan is being processed allows these invalid partial number through.  Believe it or not this happens more then you think.  For whatever reason a digit is not heard or does not get registered will cause this to happen.  Adjusting the DTMF settings does improve things in most cases but does not solve the issue.  Problem is that any number passed on by the AA that does not translate to a valid destination will get dropped.
    After much trial and tribulation I have come up with a way using the AA script to eliminate any and all none desired digit combinations to prevent anything from getting transferred by the AA that will get dropped.  It is a work around but it is effective and reliable.  Solution is simple.  Use the AA script to take specific action on only the desired responses.  Everything else goes to the default which could play an "invalid..." message or other action.  Here's how it looks:
    DP1    =    (0S0|*8S0|xxxS0)
    AA Script 1 =
    <aa>
    <form id="aadpw" type="menu"><audio src="prompt5" bargein="T"/><noinput timeout="5" repeat="T"/><dialplan src="dp1"/>
    <nomatch repeat="F"><audio src="prompt3" bargein="T"/></nomatch>
    <match>
    <case input="*8"><audio src="prompt2"/><xfer name="ext" target="vmm4"/></case>
    <case input="0"><audio src="prompt2"/><xfer name="ext" target="100"/></case>
    <case input="100"><audio src="prompt2"/><xfer name="ext" target="$input"/></case>
    <case input="102"><audio src="prompt2"/><xfer name="ext" target="$input"/></case>
    <case input="103"><audio src="prompt2"/><xfer name="ext" target="$input"/></case>
    <case input="120"><audio src="prompt2"/><xfer name="ext" target="$input"/></case>
    <case input="152"><audio src="prompt2"/><xfer name="ext" target="$input"/></case>
    <default><audio src="prompt3" bargein="T"/></default>
    </match>
    </form>
    </aa>
    It is a little like using a sledge hammer to pound in a tack but it works.  It's the only thing I was able to come up with that does.  Oh, and by the way you may notice the case for "*8".  This allows transfer from and outside line to the voice mail manager ("vmm4") on line 4.  You can modify the dial plan and AA script for any sequence you want.  The case for "0" is there to allow outside callers to press "0" and get transferred to whatever valid extension or hunt group you wish to designate.
    Hope this offers a little more insight into what was really happening.  Let me know if anyone comes up with a better way to do this.

  • [SOLVED]Kindle 5 disconnects after few seconds (USB)

    Hi,
    I have problem with my Kindle e-book reader. It worked fine last week, but now it keep disconnecting from laptop.
    When I plug it in (using USB 2.0), it is recognized, according to lsusb, but after few seconds it "disappears" from list.
    Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
    Bus 003 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
    Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
    Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
    Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
    Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
    Bus 001 Device 004: ID 1949:0004 Lab126, Inc. Amazon Kindle 3/4
    Bus 001 Device 003: ID 2232:1018
    and dmesg shows this:
    [ 44.233222] usb 1-1.2: new high-speed USB device number 5 using ehci-pci
    [ 44.338977] scsi7 : usb-storage 1-1.2:1.0
    [ 45.341509] scsi 7:0:0:0: Direct-Access Kindle Internal Storage 0100 PQ: 0 ANSI: 2
    [ 45.347348] sd 7:0:0:0: [sdb] 2846720 512-byte logical blocks: (1.45 GB/1.35 GiB)
    [ 45.453629] sd 7:0:0:0: [sdb] Write Protect is off
    [ 45.453643] sd 7:0:0:0: [sdb] Mode Sense: 0f 00 00 00
    [ 45.563370] sd 7:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 45.784393] sdb: sdb1
    [ 46.013362] sd 7:0:0:0: [sdb] Attached SCSI removable disk
    [ 46.954279] usb 1-1.2: USB disconnect, device number 5
    [ 46.955449] sd 7:0:0:0: [sdb] Synchronizing SCSI cache
    [ 46.955581] sd 7:0:0:0: [sdb]
    [ 46.955591] Result: hostbyte=0x01 driverbyte=0x00
    For powersaving I use tlp and I have this device blacklisted, so it shouldn't be the cause. And the autosuspend for USB is set to 2000s. I tried to google but nothing helps.
    Thanks
    Edit: It was because of two bad cables, the third one works. Sorry
    Last edited by Kotrfa (2013-05-16 20:33:41)

    First, connect it to another computer and try a differnet video connection. THis will tell you if the computer is doing something to contribute to teh problem...a.k.a. sending a sleep signal. If it still does not work and exhibits the same behaviour, then I am inclined to think that the backdisplay charging system (the inverter board) is not working correctly... that is, a capacitor(s) has failed.
    ... an HP employee expressing his own opinion.
    Please post rather than send me a Message. It's good for the community and I might not be able to get back quickly. - Thank you.

Maybe you are looking for