SPA112 no call waiting tone - works in PAP2T

Hi, 
SPA 112 fw 1.3.2
We are using an spa112 with Asterisk.  The phone is not hearing a call waiting tone; the caller just hears that the extension is busy.  Using an older pap2t, call waiting tone works fine.  
I've tried turning on and off Call Waiting Service.
Thank you.

Hard to give useful advice with almost no detail. I assume you didn't enabled the CW feature properly.
Catch the SIP dialog between Asterisk and SPA112 (use 'sip set debug ...' command of Asterisk's console). Also, turn on syslog&debug messages on SPA112 and catch them as well. It will help with further analysis.

Similar Messages

  • I have iPhone 5 iOS 7.0.2 and my call waiting stopped working. Anyone know how to fix this ? Or also having this issue? I hear the beep when the call comes in but not ID and no option to switch calls.

    My call waiting stopped working in iPhone 5 iOS 7.0.2 ? Anyone have this issue or know how to fix it?

    I have this issue as well and it really bothers me.

  • SPA 5xx Call Waiting Tone Length

    I am struggling to shorten the Call Waiting Tone length on a Cisco SPA514g, running sofware ver. 7.5.3, hardware ver 1.0.0.
    I am using the Metaswitch SIP Provisioning server to send a custom config fragment <Call_Waiting_Tone>440@-5;1(.1/.1/1)</Call_Waiting_Tone> to the phone.
    I have verified via the phone ui that the value is successfully entered in the "Call Waiting Tone" field under the "Regional" tab. The tone length never changes. I can remove it altogether, but not affect the -db levels or the length.
    Any ideas or suggestions?

    I've recently ran into this issue also.  I found it happens whenever I set my remote media gateway model to anything other then the default ringtone I get the extremely long CW beep.  When I set it to the default Cisco Synth tone the tone follows the config UI you stated above.

  • Dropped calls after call waiting tone

    I have been getting intermittent dropped calls for the past month when receiving incoming call waiting tones. I reported it to comcast call center. They said they performed a remote test but I never saw any resetting of the modem take place. The agent said it must be the modem. I told her that the modem (DPC3141 - Triple Play) was 3 months old and the levels were almost perfect at the modem. The agent said she would send a tech to replace the modem. I felt that it was a canned response because she really didn't know what was wrong. I later cancelled the dispatch because I didn't feel it was a modem issue. Any one out there experience same symptoms? I live in Boynton Beach, Fl.

    Hi,
    Please update to the latest version for Lync server 2013 and test again.
    You can use the Lync server logging tool on Mediation server and FE server for further troubleshooting.
    Here is the link of using the Lync logging tool:
    http://blog.schertz.name/2011/06/using-the-lync-logging-tool/
    Note: Microsoft is providing this information as a convenience to you. The sites are not controlled by Microsoft. Microsoft cannot make any representations regarding the quality, safety, or suitability of any software or information found there. Please make
    sure that you completely understand the risk before retrieving any suggestions from the above link.
    If Lync server 2013 not have Lync logging tool you can download Microsoft Lync Server 2013 Debugging Tools separately in the link below:
    http://www.microsoft.com/en-in/download/details.aspx?id=35453
    Best Regards,
    Eason Huang
    Eason Huang
    TechNet Community Support

  • Why doesn't my call waiting feature work AT ALL?

    My call waiting feature does not work at all. I receive absolutely no alert when I am on the phone and have a second incoming call. My phone goes straight to voicemail for the person who is attempting to call me while I'm on the phone.

    Em83, We know that every call is important so let's look into this together! When did this issue first begin? Any new updates to the phone applications or software? Please confirm the software currently loaded in your phone, as well. We'll . Please share details.
    TanishaS_VZW
    Follow us on Twitter @VZWSupport
    If my response answered your question please click the �Correct Answer� button under my response. This ensures others can benefit from our conversation. Thanks in advance for your help with this!!

  • HT4528 I keep hearing a call waiting tone on my Iphone 4S when I am talking on my phone?

    I keep hearing a tone for call waiting when I am talking on my Iphone 4S and there is no call waiting all?

    I am having the same problem. I downloaded it from my 4S and my ITunes account shows it was downloaded. It's not listed in the ringtones on my 4S. When I open ITunes, and plug in my 4S, I can look at the media on my device. There is a checkmark next to it and a circle to the far left, but it is not on my phone. This has not happened before. Hopefully there will be an answer soon.

  • Call waiting not working in Nokia 3120 classic

    In my Nokia 3120 classic mobile, the call waiting option is not working. If a new call comes while you're on a call, it shows the new call. But if I try to answer it, it shows some error.
    Pls help.
    Solved!
    Go to Solution.

    Call waiting is actually a network service. Your phone only facilitates this service by transmitting a command to the network when you change certain settings. 
    You should start debugging this problem by contacting your network to make sure there isn't a problem with the service.  

  • UCCX - Call Waiting Tone?

    Does anyone in the community know of a way to send an audible tone to agents (via the ear piece) when a call is in a Queue they belong to?
    My client is replacing an Aspect system which offers this functionality and they would like to have this when UCCX is implemented.
    Thanks,
    Tom

    The only idea I have seen on this topic is to create a shared line appearence with the Idle Alert Setting set to Beep and the Busy Alert Setting set to None on all of the agents' phones. Within the script you can use a place call step to ring the DN for a few seconds and then just terminate it right away. It's far from ideal but it's better than 'not possible'. Be careful with your CTI Port utilization here; I would add a sepearate CCG for this.

  • 6233 call waiting tone when in a car kit

    Can anyone help with this one? when on a call with a 6233 there is an obvious audible tone to alert you to the fact that you have another call coming in. However when in a car kit this tone is not obvious and calls are being missed altogether. Is there any way to resolve this? Can I get an audible tone to alert me to calls. Your help would be appreciated.

    No

  • Call waiting disconnects first call on SPA-3102

    Ive got this strange problem.
    When on the phone using Line 1 (voip account):
    1. I hear a call waiting tone,
    2. I press the flash hook and accept the second call.
    3. The first one gets disconnected.
    Some details about my setup:
    Enabled Codecs are G.729, G.711u and G.711a
    Preferred codec G.729
    Use Preferred Codec Only: NO
    Timer values: I found the PSTN flash hook timer value which is set at .25 sec. But this problem is when using Line 1 VoIP. So I doubt this is the issue.
    Now I "think" the SPA3102 can handle two G.729 calls (I think the spa3000 only did one G.729 codec). But even if this was the case, the codec shouldn't be a problem as my provider will allow BOTH G729 and G711.
    Any help with this is really appreciated !!
    VoIP Addict

    try the following values. these worked fine on a DECT phone according to another forum..
    Hook Flash Timer Min: 0.06
    Hook Flash Timer Max: 0.2
    Callee On Hook Delay: 0
    Reorder Delay: 5
    CPC Delay: 0.5
    CPC Duration: 0.1
    Hook Flash Tx Method: NONE
    --using a panasonic cordless phone Hook Flash Timer Max: .3 then set Flash Time on the phone itself to  400ms to 600ms..
    | isolate! isolate! isolate! |

  • Call Waiting / Conference call / Call Held Notification

    I do not get a notification saying Call waiting when i call other person who is on another line. Other phones have the notification where it show is a conference is active or if your call is on hold. Is there a way for me to get this notification on my Iphone.

    I'm not sure I quite understand what it is you are asking. Of course, not many others have either, that is why you didn't get a reply to the first time you posted this. It wasn't necessary to post a second time, you could have just bumped the first post.
    If I understand you correctly, you are expecting some type of notification on your phone when you call someone else and they are on their phone? Generally, unless they have call waiting, you get a busy signal. If they have call waiting, you can hear the phone ringing in your ear, but unless the other party answers, you get no type of notification. I've never heard of any type of notification like that before. My guess would be to contact the carrier, but again, this is something I've never heard of before.
    Or are you referring to you getting a call waiting tone on your phone if you are using the phone and someone else calls you?

  • Call waiting on 7910 phone

    Does the call waiting feature work with a 7910 phone? If so how?

    The Call Waiting feature is enabled very similarly to your phone at home where as you flash the hook in order to accept the 2nd call. Also like your phone at the house you can switch back and forth between lines by flashing the hook repeatedly (ie using the hold button on the phone)

  • 1.call information such as call waiting,call forwarding, call holding is not working when caller the call me or im wait for my call i cant see any title by iphon , and also holding is the same.2. there is not any option for call baring.

    Hi. please solve my problem.
    .call information such as call waiting,call forwarding, call holding is not working when caller the call me or im wait for my call i cant see any title by iphon , and also holding is the same.2. there is not any option for call baring.3.playback music is not hearing by second partner during the call.4.i cant select ringing ton from saving tons.
    thank you in advance.

    Hi Ersin,
    Exception 1 would seem to be FORMATTING_ERROR, which suggests something in the design of the Smartform.  However, that doesn't fit with the form being generated from a report, but only erroring when called from a function module.  I can think of no reason why the different calling method would be a factor.
    When FORMATTING_ERROR is raise it should also set a message ID and number, are you able to determine what they are?
    Regards,
    Nick

  • Call waiting option isn't working

    Im using i6 phone and currently my call waiting option isn't working. I want to know how can I Enable it?

    Hey pramodsean,
    If your carrier supports call waiting, you can turn it on by going to Settings > Phone > Call Waiting. If the setting is not available, contact your carrier. See this article for reference -
    iPhone: Understanding phone features - Apple Support
    Thanks for using Apple Support Communities.
    Happy computing,
    Brett L 

  • Call Waiting, Exchange Peak On/Off, Ring tone voly...

    When are Nokia supposed to fix:
    Call Waiting Error for Telia & 3 users in Sweden that appeared after 12070 update?
    When do we get Peak On/Off when using Exchange sync?
    Separate volym for Ringtone and other Media so you don't miss a call?
    Wy don´t Nokia send an Symbian phone to MS so they know what we want in a Nokia phone!!
    I like both Symbian and Windows Phone and I need to have both now to get complete.
    Windows Phone good user interface. Symbian all settings and features.
    Kads

    Please search the forums...you'll see several post for the same question...
    Pulling the battery is the only way stop it. It'll work normal for a while and then happen again. Known issue with the 5.0 software upgrade.

Maybe you are looking for