SPA2002 in SIP server environment

Hello,
I am using the SPA2002 that registers remotely to a SIP server. The phones register correctly and can reach any other user agent (not SPA2002). the problem is that other user agents cannot call the SPA2002 until the SPA2002 calls first then the other US calls immediately. If other UA does not call the SPA2002 for about 10 minutes then calls to the SPA2002 will not be possible.
Did any one meet this problem before?

There is a setting "NAT Keep Alive Enable" which will send a message every 15 seconds or so to the SIP server to keep the router sip signalling port open. Did you try setting that field to yes?

Similar Messages

CVP - SIP Server Groups and Redundant SIP Proxy (CUPS)

I am migrating from a CVP 7 + UCCE 7.5 solution which uses srv.xml files on the CVP servers to implement redundancy
from CVP to the SIP Proxies (which are CUPS based).
In the new CVP 8.5 + UCCE 8.5 solution, I am trying to set up equivalent redundancy, which
is now done via Server Groups.
The solution is geographically diverse, with one CVP server + a CUPS server (publisher) at Site1,
and the second CVP + CUPS server (subscriber) at site 2.
Previously (on CVP 7), I was able to configure each CVP server so that its priority was to use the CUPS server at its
"local" site. Hence there were 2 different srv.xml files, one for each CVP server.
To configure this in CVP 8.5, I would need 2 SIP Server groups, to give each CVP a group
configured to prefer the "local" CUPS server. But when I configure a SIP server group(s) pointing to CUPS, I seem to be only able
to get one single Server Group to work. That single Server Group only works if the server group name
matches exactly the Domain Name configured in CUPS. Since CUPS' Domain name is a single cluster wide name,
I can get only one Server Group working, not the two that I need.
So, where am I going wrong?
Regards.

Fairly new to CVP and had a question about how to configure the dialed number patterns so they point to more than 1 CUCM. My environment doesn't have a SIP Proxy or DNS Srv. That said, I tried to create as what was mentioned above - SIP Serve Group with 2 CUCM Subs then have a dialed number pattern point to it. However, when I initiate a call to an ICM script and eventually hit an agent, it flips between ready and reserve. When I change the dialed number pattern to point to a specific CUCM, it works fine. Followed all the aobve recommendations as well. Any idea how to make this work? Hoping I'm just missing something here...

Unable to connect to SIP server

Hi,
Need some assistance here.(using E71)
When i try to connect to a SIP Server(USING Sip Express Router), it failed to get registered. From the sniffing via the ethereal(WIFI), the Flow are follow :
1. UA request register request to sip server
2. Sip Server reply with : Status : 401 Unauthorised
In a actually environment, the UA should have the 3rd steps where it re-sent the reqgister request with the username and password.
But somehow, nokia E71 is not doing it.
any suggestion?
P/S : http://www.sipcenter.com/sip.nsf/html/SIP+Application+Server+Functionality
(it shows how the UA should connect to the Server)

The problem could be the router or its firewall, but it could also be that your Indian isp is blocking voip connections. There have been reports that this is not unknown in India. Sometimes this type of blocking is done by discarding packets destined to the standard voip sip signalling port 5060. You can easily change the sip signalling port in the SPA3102 for the packets coming back to the SPA and in fact routers often changes the port without your knowledge, but packets going to the voip provider must use the port number specified by the provider. Since you can access the internet with your pc, I would try to run some tests to see if this is the case.
I would run some ping tests and tests to see if I could register with other providers or services that use alternate or alternative sip signalling ports.

Deploying war file in weblogic SIP server 2.2

Hi,
I trying to deploy a "sar" file in weblogic SIP server,but it is not allowing me to do that.So one of my collegue told me to change the "sar" to "war" and try to deploy.
When i am trying to deploy that it is saying that unable to find deployment descripter WEB-INF/web.xml in the war file.Actually it is there.But i don't know why it is giving that error.
Actually i need to deploy "sar" file and i changed that file into "war" file
What are all the trail and error to solve this problem
(1)I made the "war" file from file folders.
suppose my application directory name is "myapp"
then i am going into the "myapp" folder and from there i am trying to make war file and it is having all the related class files , sip.xml file , web.xml file.
Then i tryed to deploy that file from weblogic SIP server 2.2.console.
(2) Next I included the weblogic.xml file also into the war file.
(3)The "sar" file working fine in SDS 3.1,but not in we blogic SIP server.
(4)The SDS3.1 is working with JRE 5 so i changed that JRE from 1.5 to jre 1.4. and again prepared the sar file and changed that SAR file to WAR file.
I created a domain in SIP server which was created in "user_projects."
For e.g., the domain name is "mydomain" and
the directory structure is
mydomain
|
|
|----------applications(dir)
|
|----------myserver(dir)
|
|----------rmfilestore(dir)
|
|----------sipserver(dir)
|
|-----------boot (file)
|
|-----------config.xml
|
|-----------startWeblogic
|
|-----------stopWebLogic
|
|----------upload-------xxxxmanager----META-INF---WEB-INF----log4j.properties
--------------sip.xml
-----------------web.xml
-------------weblogic.xml
web.xml, sip.xml,log4j.properties are under WEB-INF folder
Do i need to change any path setting in startWebLogic.cmd file.I didn't change any thing in the startWeblogic.cmd.
Since my war file is having all the related files like all the related "jar" files in that.
Any body's help will be appriciated.
Thanks
vish

Can any body please reply for above question.
Hi BEA support please flash some light on my above question
vkviswanadh

Intermittend DNS resolution, timeserver, group policy updates errors in client logs in Win 2012 R2 single server environement

We recently switched hardware and server software Win SBS 2008 to 2012R2 for a small network roughly 40 clients (Win7 Pro / Win 8.1 Pro) about 16 running concurrently at a given time and one network printer with the printer queue residing on the DC as well.
I read that a single server environment might not be ideal in particular no fail-over but that is an accepted risk in this particular network here.
Errors:
Error 1043: Timeout during name resolution request
Error 1129: Group policy updates could not be processed due to DC not available
Error 5719: Could not establish secure connection to DC, DC not available
Occasionally but disappears after a while
Error 134: As a result of a DNS resolution timeout could not reach time server
Symptoms
On Win 7 Clients
Network shares added through Group Policy will not show sometimes
Network shares disconnect (red X) and when accessed return access authorization error after one or two clicks on the share finally grant access again
When the issue with accessing network shares occurs, it usually also affects Internet access meaning a 'server not responding' error appears in the browser windows when trying to open just any web page
nslookup during the incident returns cannot resolve error
ipconfig on client shows correct default router (VDSL Router) and DHCP / DNS Domain Controller
Also, the Win system log shows the above errors during these incidents, however, the nuimber of incidents vary from 20-30
On Win 8.1 Clients
Same as above with the slight variation for network shares apparently due to Server 2012 and Win 8.1 clients managing drive shares differently. However, network share refresh does not work with this clients. In most cases only a gpupdate /force returns
drive shares but usually only for the active session. After logoff / logon the shares are gone again.
The issue does appear to be load related since it occurs even if there are only one or two workstations active.
Server Configuration
Dell R320 PowerEdge 16GB / 4TB 7200RPM RAID10 / GBitEthernet
Zyxel 1910-48 Port Switch
VDSL 50Mbps Down / 20Mbps Up
Since the DC is the only local DNS and there are no plans to add another one or move DNS to another server, the DNS server is configured with this own address as preferred DNS with three DNS forwarders 1) VDSL Router 2) ISP DNS1 3) ISP DNS2
Currently only one Network card is active for problem determination reasons.
There appears to be no consensus concerning IPV6 enabled or disabled, I tried both with no apparent effect
I have set all network cards server and client to Full Duplex and the same speed, also disabled Offload functions within the adapter settings. Some but no consistent improvements.
Best Practice Analyzer Results
DNS server scavening not enabled
Root hint server XYZ must respond to NS queries for the root zone
More than one forwarding server should be configured (although 3 are configured)
NIC1 should be configured to use both a preferred and alternate DNS (there is only one DNS in this network)
I have found some instructions to apply changes to the clients through a host file but I would rather like to understand whether this DNS response time issue can be resolved on the server for example timing setting perhaps. Currently the DNS forwarders are
set to 3 second.
Since a few people have reported issues with DNS but most are working with multi DNS, DC environment I could not really apply any suggestions made there. perhaps there is anyone like me who is running a single server who has overcome or experience the same
issues. Any help would be appreciated

Hello Milos thx for your reply.. my comments below
1. What does it "switched"? You may mean migration or new installation. We do not know...
>> Switched is probably the incorrect term, replaced would be the appropriate wording. Before, there was a HP Proliant Server with SBS 2008 with distinct domain and now there is a Dell Server with MS 2012 R2 with a distinct domain. Client were
removed from one (SBS) domain and added to the new Server 2012 domain. Other components did not change for example same Network Switch or VDSL Router, Workstations and Printer
2. Two DCs are better alternative. Or backup very frequently. There are two groups of administrators. Those who have lost DC and those who will experience this disaster in near future.
>> Correct, and I am aware of that
3. NIC settings in W 7 and W 8.1, namely DNS points to DC (...and NOTHING else. No public IP or that of router DNS.))
>> Correct, this is how it's currently implemented. Clients point to DC for DHCP and DNS and Default Router, no public IP or DNS. The only references to ISP DNS exist on the VDSL Router itself as provided through ISP when establishing VDSL
Link and the list of Forwarders in the DNS Server configuration. However, I have just recently added the ISPs DNS as forwarders for test purposes and will probably learn tomorrow morning whether this had any effect for better or worse.
4. Do nslookup to RR on clients. RR branch is saying client basic info on LDAP parameters of AD.
>> Will post as soon as available
5. I do not use forwarders and the system works
>> Ok, does this mean it works for you in a similar or the same infrastructure setup or are you saying it is not required at all and I can remove any forwarder in a scenario like mine? If not required can you explain a bit more why it is not
required apart from that it does work for you that way?
6. DHCP should sit on DC (DHCP on router is disabled)
>> Correct, no other device is configured to provide DHCP service other than DC and DHCP is currently running on DC
7. NIC settings in DC points to itself (loopback address 127.0.0.1)
>> Are you sure this is still correct and does apply to Server 2012? I am reading articles stating that it should be the servers own IP but local loop or should this be added as alternate DNS in addition to the servers own IP?
8. Use IPCONFIG /FLUSHDNS whenever you change DNS settings.
>> OK, that was not done every time I changed some settings but I can do that next week. Reboot alone would not suffice, correct?
9. Test your system with dcdiag.
>> See result below
10. Share your findings.
Regards
Milos
Directory Server Diagnosis
Performing initial setup:
   Trying to find home server...
Home Server = GSERVER2
   * Identified AD Forest.
   Done gathering initial info.
Doing initial required tests
Testing server: Default-First-Site-Name\GSERVER2
      Starting test: Connectivity
         ......................... GSERVER2 passed test Connectivity
Doing primary tests
   Testing server: Default-First-Site-Name\GSERVER2
      Starting test: Advertising
         ......................... GSERVER2 passed test Advertising
      Starting test: FrsEvent
         ......................... GSERVER2 passed test FrsEvent
      Starting test: DFSREvent
         ......................... GSERVER2 passed test DFSREvent
      Starting test: SysVolCheck
         ......................... GSERVER2 passed test SysVolCheck
      Starting test: KccEvent
         ......................... GSERVER2 passed test KccEvent
      Starting test: KnowsOfRoleHolders
         ......................... GSERVER2 passed test
         KnowsOfRoleHolders
      Starting test: MachineAccount
         ......................... GSERVER2 passed test MachineAccount
      Starting test: NCSecDesc
         ......................... GSERVER2 passed test NCSecDesc
      Starting test: NetLogons
         ......................... GSERVER2 passed test NetLogons
      Starting test: ObjectsReplicated
         ......................... GSERVER2 passed test
         ObjectsReplicated
      Starting test: Replications
         ......................... GSERVER2 passed test Replications
      Starting test: RidManager
         ......................... GSERVER2 passed test RidManager
      Starting test: Services
         ......................... GSERVER2 passed test Services
      Starting test: SystemLog
         ......................... GSERVER2 passed test SystemLog
      Starting test: VerifyReferences
         ......................... GSERVER2 passed test VerifyReferences
   Running partition tests on : ForestDnsZones
      Starting test: CheckSDRefDom
         ......................... ForestDnsZones passed test CheckSDRefDom
      Starting test: CrossRefValidation
         ......................... ForestDnsZones passed test
         CrossRefValidation
   Running partition tests on : DomainDnsZones
      Starting test: CheckSDRefDom
         ......................... DomainDnsZones passed test CheckSDRefDom
      Starting test: CrossRefValidation
         ......................... DomainDnsZones passed test
         CrossRefValidation
   Running partition tests on : Schema
      Starting test: CheckSDRefDom
         ......................... Schema passed test CheckSDRefDom
      Starting test: CrossRefValidation
         ......................... Schema passed test CrossRefValidation
   Running partition tests on : Configuration
      Starting test: CheckSDRefDom
         ......................... Configuration passed test CheckSDRefDom
      Starting test: CrossRefValidation
         ......................... Configuration passed test CrossRefValidation
   Running partition tests on : GS2
      Starting test: CheckSDRefDom
         ......................... GS2 passed test CheckSDRefDom
      Starting test: CrossRefValidation
         ......................... GS2 passed test CrossRefValidation
   Running enterprise tests on : GS2.intra
      Starting test: LocatorCheck
         ......................... GS2.intra passed test LocatorCheck
      Starting test: Intersite
         ......................... GS2.intra passed test Intersite
Server: gserver2.g2.intra
Address: 192.168.240.6
*** gserver2.g2.intra can't find g2: Non-existent domain
> gserver2
Server: gserver2.g2.intra
Address: 192.168.240.6
g2.intra
        primary name server = gserver2.g2.intra
        responsible mail addr = hostmaster.g2.intra
        serial = 443
        refresh = 900 (15 mins)
        retry   = 600 (10 mins)
        expire = 86400 (1 day)
        default TTL = 3600 (1 hour)
> wikipedia.org
Server: gserver2.g2.intra
Address: 192.168.240.6
Non-authoritative answer:
wikipedia.org   MX preference = 10, mail exchanger = polonium.wikimedia.org
wikipedia.org   MX preference = 50, mail exchanger = lead.wikimedia.org
polonium.wikimedia.org internet address = 208.80.154.90
polonium.wikimedia.org AAAA IPv6 address = 2620:0:861:3:208:80:154:90
lead.wikimedia.org      internet address = 208.80.154.89
lead.wikimedia.org      AAAA IPv6 address = 2620:0:861:3:208:80:154:89
Final benchmark results, sorted by nameserver performance:
(average cached name retrieval speed, fastest to slowest)
192.168.240. 6 | Min | Avg | Max |Std.Dev|Reliab%|
----------------+-------+-------+-------+-------+-------+
+ Cached Name   | 0,001 | 0,002 | 0,003 | 0,001 | 100,0 |
+ Uncached Name | 0,027 | 0,076 | 0,298 | 0,069 | 100,0 |
+ DotCom Lookup | 0,041 | 0,048 | 0,079 | 0,009 | 100,0 |
---<-------->---+-------+-------+-------+-------+-------+
             gserver2.g2.intra
                Local Network Nameserver
195.186. 4.162 | Min | Avg | Max |Std.Dev|Reliab%|
----------------+-------+-------+-------+-------+-------+
- Cached Name   | 0,022 | 0,023 | 0,025 | 0,000 | 100,0 |
- Uncached Name | 0,025 | 0,071 | 0,274 | 0,065 | 100,0 |
- DotCom Lookup | 0,039 | 0,040 | 0,043 | 0,001 | 100,0 |
---<-------->---+-------+-------+-------+-------+-------+
                     cns8.bluewin.ch
           BLUEWIN-AS Swisscom (Schweiz) AG,CH
195.186. 1.162 | Min | Avg | Max |Std.Dev|Reliab%|
----------------+-------+-------+-------+-------+-------+
- Cached Name   | 0,022 | 0,023 | 0,026 | 0,001 | 100,0 |
- Uncached Name | 0,025 | 0,072 | 0,299 | 0,066 | 100,0 |
- DotCom Lookup | 0,039 | 0,042 | 0,049 | 0,003 | 100,0 |
---<-------->---+-------+-------+-------+-------+-------+
                     cns7.bluewin.ch
           BLUEWIN-AS Swisscom (Schweiz) AG,CH
    8. 8. 8. 8 | Min | Avg | Max |Std.Dev|Reliab%|
----------------+-------+-------+-------+-------+-------+
- Cached Name   | 0,033 | 0,040 | 0,079 | 0,011 | 100,0 |
- Uncached Name | 0,042 | 0,113 | 0,482 | 0,097 | 100,0 |
- DotCom Lookup | 0,049 | 0,079 | 0,192 | 0,039 | 100,0 |
---<-------->---+-------+-------+-------+-------+-------+
             google-public-dns-a.google.com
                 GOOGLE - Google Inc.,US
UTC: 2014-11-03, from 14:33:12 to 14:33:29, for 00:17,648
15: 40
192.168.240. 6 | Min | Avg | Max |Std.Dev|Reliab%|
----------------+-------+-------+-------+-------+-------+
+ Cached Name   | 0,001 | 0,002 | 0,004 | 0,000 | 100,0 |
+ Uncached Name | 0,025 | 0,074 | 0,266 | 0,063 | 100,0 |
+ DotCom Lookup | 0,042 | 0,048 | 0,075 | 0,007 | 100,0 |
---<-------->---+-------+-------+-------+-------+-------+
             gserver2.g2.intra
                Local Network Nameserver
195.186. 1.162 | Min | Avg | Max |Std.Dev|Reliab%|
----------------+-------+-------+-------+-------+-------+
- Cached Name   | 0,022 | 0,024 | 0,029 | 0,001 | 100,0 |
- Uncached Name | 0,024 | 0,073 | 0,289 | 0,067 | 100,0 |
- DotCom Lookup | 0,039 | 0,041 | 0,043 | 0,001 | 100,0 |
---<-------->---+-------+-------+-------+-------+-------+
                     cns7.bluewin.ch
           BLUEWIN-AS Swisscom (Schweiz) AG,CH
195.186. 4.162 | Min | Avg | Max |Std.Dev|Reliab%|
----------------+-------+-------+-------+-------+-------+
- Cached Name   | 0,022 | 0,024 | 0,029 | 0,001 | 100,0 |
- Uncached Name | 0,025 | 0,073 | 0,286 | 0,065 | 100,0 |
- DotCom Lookup | 0,041 | 0,066 | 0,180 | 0,037 | 100,0 |
---<-------->---+-------+-------+-------+-------+-------+
                     cns8.bluewin.ch
           BLUEWIN-AS Swisscom (Schweiz) AG,CH
    8. 8. 8. 8 | Min | Avg | Max |Std.Dev|Reliab%|
----------------+-------+-------+-------+-------+-------+
- Cached Name   | 0,033 | 0,038 | 0,077 | 0,009 | 100,0 |
- Uncached Name | 0,042 | 0,105 | 0,398 | 0,091 | 100,0 |
- DotCom Lookup | 0,049 | 0,066 | 0,141 | 0,025 | 100,0 |
---<-------->---+-------+-------+-------+-------+-------+
             google-public-dns-a.google.com
                 GOOGLE - Google Inc.,US
UTC: 2014-11-03, from 14:39:59 to 14:40:12, for 00:13,363

How to reset password of weblogic sip server 3.1

Hi ,
Can anybody help me in resetting the username/password of weblogic sip server 3.1
Thanks a lot
Regards
Saurabh

Hi,
If we have only one admin account available, I am afraid there is no means to reset the password other than reinstalling Windows. See this article as a reference:
What to do if you forget your Windows password
Besides, we may try to create the Windows 8.1 install media with the following article:
Create installation media for
Windows 8.1
How to perform a clean installation of Windows
And please note, if we do a clean install, we need to activate Windows again.
If Windows 8 came preinstalled on your computer, your product key should be on a sticker on your computer or with your documentation. Or we may contact the manufacturer for further help.
Best regards
Michael Shao
TechNet Community Support

Do I need DFSR in a single server environment?

I have a 2012 Host, running a single 2012 Guest. Guest is running as a DC with AD, DNS, DHCP, and File Services. DFSR is running, and it gives a warning every time my back runs (Backup is running on Host). Warning is The DFS Replication
service stopped replication on volume F:......and long message about Database, yada yada yada.
Do I need to run DFSR? Again, single server, no file replication to different offices. I'm not finding a clear answer to that question.
Second, Server Manager should, according to TechNet, have under the Tools option the ability to turn off DFSR. I cannot find that option. So, IF I can turn it off, can I simply disable the DFS Namespace and DFS Replication services?
I would prefer eliminating rather than ignoring warnings.
Thanks

Sorry, one more time. I have a single server environment, there is NO upstream domain controller, no replication between DC's. There is ONE DC. So, this is digressing into two questions. One, why do I need to run DFSR (again, lots
of articles talking about how to turn it off, and not as a discussion of temporary turn off https://msdn.microsoft.com/en-us/library/cc753144.aspx) in a single server, single domain, non-replicating environment.
Second, how do I address the warning I receive during my backup? It appears to be caused by a replication error to downstream servers, since there is no downstream server, I should be able to resolve it by turning DFSR off. I would like some
documentation discussing the issue of turning it off in a non-DFS environment.
The DFS Replication service stopped replication on volume F:. This occurs when a DFSR JET database is not
shut down cleanly and Auto Recovery is disabled. To resolve this issue, back up the files in the affected replicated folders, and then use the ResumeReplication WMI method to resume replication.
Additional Information:
Volume: F:
GUID: 65E46942-B9D6-11E3-9400-00155D325402
Recovery Steps
1. Back up the files in all replicated folders on the volume. Failure to do so may result in data loss due
to unexpected conflict resolution during the recovery of the replicated folders.
2. To resume the replication for this volume, use the WMI method ResumeReplication of the DfsrVolumeConfig
class. For example, from an elevated command prompt, type the following command:
wmic /namespace:\\root\microsoftdfs path dfsrVolumeConfig where volumeGuid="65E46942-B9D6-11E3-9400-00155D325402"
call ResumeReplication
For more information, see http://support.microsoft.com/kb/2663685.
Jeff Ferris

Best Practice to generate UUIDs in a Cluster-Server Environment

Hi all,
I just need some inputs over the best practices to generate UUIDs in typical internet world where there are multiple servers/JVMs involved for load balancing or traffic distribution etc. I know JAVA is shipped with very efficient UUID generator API.
But still that doesn't solve the issue in multiple server environment.
For the discussion sake lets assume I need it to be unique over the setup than a near unique.
How do you guys approach it?
Thanks you all in advance.

codeNombre wrote:
jverd wrote:
codeNombre wrote:
Thanks jverd,
So adding to the theory of "distinguishing all possible servers" in addition to UUID over each server would be the way to go.If you're unreasonably paranoid, sure.I think its a common problem and there is a big number of folks who might still be bugged about the "relative uniqueness" of UUID in long run. People who don't understand probability and scale, sure.
Again coming back to my original problem in an "internet world", shouldn't the requirement like unique id between different servers be dealt with generating the UUID's at a layer before entering into the multi-server setup. Where would that be? I don't have the answer..Again, that is the POINT of the UUID class--so that you can generate as many IDs as you want and still be confident that nobody anywhere is in the world has ever generated any of those same IDs. However, if your requirements say UUID is not good enough, then you need to define what is, and that means having a lot of foresight as to how this system will evolve and how long it will live, AND having total control over some aspect of your servers, AND having a process that is so good that it's LESS LIKELY for a human to screw up and re-use a "unique" server ID than the probabilities I presented in my previous post.

Installing Acrobat Pro 9.2 in a Terminal Server Environment

Hi everyone,
we're facing massive problems in our attempts to install Acrobat Pro 9.2 in a terminal server environment. It seems to be impossible to convert for example a .doc-file into a pdf via the adobe pdf-printer using a restricted user-account. It causes an "Access denied"-popup. We solved this subproblem by granting the user write-permission in the respective registry-key (HKLM\Software\Adobe). By now everytime we try, the application freezes after the "copy-status-bar" is filled. Using a power user instead of a normal user solves this problem. So the question is what's the relevant difference between the rights of those user groups.
Thanks for your help!

You can also try to update your Acrobat by applying patches one by one.
to update upto latest version of Acrobat i.e 9.5, you need to apply the following updates
9.3.0   download location: < http://www.adobe.com/support/downloads/detail.jsp?ftpID=4605 >
9.3.2   download location < http://www.adobe.com/support/downloads/detail.jsp?ftpID=4654 >
9.3.3   download location < http://www.adobe.com/support/downloads/detail.jsp?ftpID=4695 >
9.4      download location < http://www.adobe.com/support/downloads/detail.jsp?ftpID=4851 >
9.4.2   download location < http://www.adobe.com/support/downloads/detail.jsp?ftpID=4931 >
9.4.5   download location < http://www.adobe.com/support/downloads/detail.jsp?ftpID=5118 >
9.4.6   download location < http://www.adobe.com/support/downloads/detail.jsp?ftpID=5237 >
9.5     download location < http://www.adobe.com/support/downloads/detail.jsp?ftpID=5330 >
You can download the above mentioned patches from the corrosponding download link and apply one by one in same order as mentioned above.
This is a bit lengthy process, but I hope you will be able to update your Acrobat.
Thanks.

Document.passivate() giving problem in the server environment

I am having two J2EE web applications accessing PDF forms using LiveCycle API. They both are invoking a short-lived process with RenderPDFForm service that takes form and formdata and renders a PDF form. The code where these applications communicate with Livecycle server is same for both the apps. The applications work fine in the local environment. But in the server environment, one of them work and the other fails with security certificate exception. These applications are deployed to the same server. The application that fails is failing during document.passivate() call. Here is the log message.
com.adobe.idp.DocumentError: javax.net.ssl.SSLHandshakeException: com.ibm.jsse2.util.h: PKIX path validation failed: java.security.cert.CertPathValidatorException: The certificate expired at Wed Jul 01 15:28:21 CDT 2009; internal cause is:
java.security.cert.CertificateExpiredException: NotAfter: Wed Jul 01 15:28:21 CDT 2009
at com.adobe.idp.Document.passivateInitData(Document.java:1562)
at com.adobe.idp.Document.passivate(Document.java:1241)
at com.adobe.idp.Document.passivate(Document.java:1185)
at com.adobe.idp.DocumentManagerClient.passivate(DocumentManagerClient.java:236)
at com.adobe.idp.dsc.provider.impl.base.RequestOutputStream.defaultPassivate(RequestOutputSt ream.java:40)
at com.adobe.idp.DocumentRequestOutputStream.passivate(DocumentRequestOutputStream.java:56)
at com.adobe.idp.Document.writeObject(Document.java:872)
I know it looks like a security certificate exception. But the rest of the application work just fine. The application fails only during document.passivate().
Any ideas ?
Thanks,
Jytohi

I am having two J2EE web applications accessing PDF forms using LiveCycle API. They both are invoking a short-lived process with RenderPDFForm service that takes form and formdata and renders a PDF form. The code where these applications communicate with Livecycle server is same for both the apps. The applications work fine in the local environment. But in the server environment, one of them work and the other fails with security certificate exception. These applications are deployed to the same server. The application that fails is failing during document.passivate() call. Here is the log message.
com.adobe.idp.DocumentError: javax.net.ssl.SSLHandshakeException: com.ibm.jsse2.util.h: PKIX path validation failed: java.security.cert.CertPathValidatorException: The certificate expired at Wed Jul 01 15:28:21 CDT 2009; internal cause is:
java.security.cert.CertificateExpiredException: NotAfter: Wed Jul 01 15:28:21 CDT 2009
at com.adobe.idp.Document.passivateInitData(Document.java:1562)
at com.adobe.idp.Document.passivate(Document.java:1241)
at com.adobe.idp.Document.passivate(Document.java:1185)
at com.adobe.idp.DocumentManagerClient.passivate(DocumentManagerClient.java:236)
at com.adobe.idp.dsc.provider.impl.base.RequestOutputStream.defaultPassivate(RequestOutputSt ream.java:40)
at com.adobe.idp.DocumentRequestOutputStream.passivate(DocumentRequestOutputStream.java:56)
at com.adobe.idp.Document.writeObject(Document.java:872)
I know it looks like a security certificate exception. But the rest of the application work just fine. The application fails only during document.passivate().
Any ideas ?
Thanks,
Jytohi

When we go for shared Server environment?

When we go for shared Server environment from Dedicated server mode?
When we have to choose thi shared Server mode?
Which is the optimized way?

> When we go for shared Server environment from Dedicated server mode?
You do not. It is not one or the other - it is using both correctly. You want shared server sessions to service applications (any, from web/app servers to flat clients) that are OLTP in nature. They fire off short-and-sweet SQLs that takes a second or three to execute.
A shared server pool of a few processes can service a very large number of clients.
You want to use dedicated servers to service OLAP type clients. They fire off complex SQLs that can tie up the server processes for several minutes at a time.
And that in a nutshell is how to apply the two. It is not Shared Servers versus Dedicated Server. It is about using The Right Tool For The Job. Nothing more and nothing less.
As for Windows, I will not really bother quickly with shared server connections. On Windows both shared and dedicated servers runs as threads in the main Oracle executable process image.
There is thus very little resource saving by reducing the number of threads as the footprint of a thread is tiny in comparison to a brand new process. The amount of resources saved by a reducing the number of dedicated server threads is not significant. If anything, Oracle on Windows has shown to scale better than Oracle on Linux in this regard. (refer to [url http://www.perftuning.com/pdf/Comparison_Oracle_Windows_Linux.pdf]A Comparison of Oracle Database 10gR2 Real Application Cluster Performance on Microsoft Windows 2003 Server Enterprise Edition x64 and Red Hat Enterprise Linux x86_64 from the Performance Tuning Corporation).
And this is exactly the opposite of how Oracle behaves on Unix. Each server process is a physical kernel process. This means that a servicing a 1000 concurrent sessions with a 1000 dedicated server processes, each consuming memory and resources, are expensive. Conversely, supporting a 1000 concurrent sessions with a 100 shared server processes is (almost) 90% cheaper.
This makes Shared Server a desirable option to use to scale OLTP sessions on Unix-based systems (or any platform where Oracle does not use multi-threading but multi-processing).
PS. As the Linux kernel support Posix threads (see http://en.wikipedia.org/wiki/Native_POSIX_Thread_Library), it begs the question as to when Oracle is going to support multi-threading on Linux instead of multi-processing.. or at least give us the option to choose.

GPs in multiple server environment

Hi,
Does anyone have experience using GP in a multiple WAS server environment. Our scenario is one in which different servers have different user groups and are located in different regions. We want to have a GP be able to transfer a process to another user group on another server and have the process flow continue there.
Is there something available "out of the box" or is it necessary to develop custom code (in all likelihood based on web-services)?
Thanks.
Dick

Hi Dick,
This is an interesting problem that you have.
There is no out of the box solution for this, but you may be able to architect this in a way that it would not require any custom code.
If you created a GP process for every region, which in all make up the logical super GP process, you can transfer process state and perform instantiation from one to the other.
For instance:
Process 1 (Region US, Server 1) upon completion starts Process 2 (Region EMEA, Server 2). The last step (Action) of Process 1 would be a Web Service Callable object which starts Process 2 and passes any PK's for state information.
If you are using CAF Entities for persistence, I recommend that you keep these all on the same server and the distributes GP processes can access as needed.
Does this make sense?
Best Regards,
Austin.

NullPointer when invoke InitialContext in standard application sip server

I am unable to do a new InitialContext() in an application that does not have any sipservlets , but is deployed on sip server engine tier
When an application is deployed in weblogic engine server (sip server 3.1 ) without a sip.xml as the application does
Not have any sip servlets , a new InitialContext() throws a NullpointerException . The stack trace is below .
This error is not encountered in weblogic 9.2 server (non sip server)
InitialContext ic = new InitialContext();
javax.naming.NamingException [Root exception is java.lang.NullPointerException: SIP Servlet context not found]
at javax.naming.spi.NamingManager.getURLObject(NamingManager.java:588)
at javax.naming.spi.NamingManager.getURLContext(NamingManager.java:533)
at javax.naming.InitialContext.getURLOrDefaultInitCtx(InitialContext.java:279)
at javax.naming.InitialContext.lookup(InitialContext.java:351)
at

Hi B.,
have you managed to find the solution for this problem? I'm facing same issue.
I also tried to publish the WS in standalone app (via javax.xml.ws.Endpoint.publish()) and it worked with no problem that way. However, when I moved this to servlet definition, it failed.
Thanks a lot.
Regards,
F.

Dial-up connection between Asterik SIP server and Cisco 5400

Hi,
We have a setup for dial-up. The incoming call lands on Cisco 5400 and is forward to PGW using mgcp intergration. PGW sends it to Asterik SIP server over SIP. This Asterik Server sends it to another Cisco 5400 over SIP for Internet.
The issue is for some dial-up user, it works fine. But for some it doesn't. The problem is when we see the log on the last Cisco 5400, the incoming call tone is detected as FAX tone rather then Modem tone.
Any idea why is it so??

Hi,
We have a setup for dial-up. The incoming call lands on Cisco 5400 and is forward to PGW using mgcp intergration. PGW sends it to Asterik SIP server over SIP. This Asterik Server sends it to another Cisco 5400 over SIP for Internet.
The issue is for some dial-up user, it works fine. But for some it doesn't. The problem is when we see the log on the last Cisco 5400, the incoming call tone is detected as FAX tone rather then Modem tone.
Any idea why is it so??

Run a report made in Rerports 9i in client/server environment

Hello
I need to run a report made in Reports 9i in a client/server environment, but we don´t want to install the developer suite. Reports 6i had a runtime tool how can i do in Reports 9i?
PD: si alguien me puede responder en español seria fantastico.
Thank you
Angelo J. Gonzalez

In client server mode you can use RUN_PRODUCT built-in. Lookup help for this built-in for more details.
Best of luck!

SPA2002 in SIP server environment

Similar Messages

Maybe you are looking for