SPA2102 Message Waiting Indicator always on

When I activate message waiting indicator (Voice - User 1 - Supplementary Service Settings - Message Waiting: Yes)
my telephone indicator light flashes continually whehter there is a message or not.
Am I missing something? Is there another setting point?  This has been a problem from the start. 
there was another posting exactly like this back in 2009 but it was never answered/resolved.
Help !!

I have exactly the same problem.  But when I desactivate message waiting indicator (Voice - User 1 - Supplementary Service Settings - Message Waiting: NO), I have no message waiting indicator (no light on an no tone) when I have a new voice mail message.
The Line 1 has MWI Serv - yes and vmwi Serv has yes too.
When I activate message waiting indicator (Voice - User 1 - Supplementary Service Settings - Message Waiting: YES), the lignt and tone are Always on whehter there is a message or not.
SPA2102, Software Version 5.2.13 (004) Hardware Version 1.3.5(a).
Thank You

Similar Messages

  • Illuminate Cisco IP Phones Visual message waiting indicator (VMWI or MWI) ?

    How can I programatically illuminate Cisco IP Phones Visual message waiting indicator (VMWI or MWI) ?

    Hello Lesser,
    So you are wanting to configure MWI for your phones correct?
    Check this documentation for example of configuration:
    http://www.cisco.com/en/US/products/sw/voicesw/ps2237/products_tech_note09186a0080711ae3.shtml
    D_a_v_i_D

  • SPA303 Message Waiting Indicator for specific line only

    I have an SPA303 configured with 2 lines (extensions).
    I want the message waiting indicator to only show for line 2, not line 1.
    I've tried going to Advanced, Voice, Ext1 and setting "Message Waiting" to No
    and for Ext2 setting it to Yes. 
    Hit "Submit All Changes"
    After phone reboots, Ext1 still says Yes, and Ext2 still says No.  I cant seem to change these.
    Is this the correct way to accomplish my request?

    I have no SPA303 here, but it is almost identical hardware and exactly the same firmware (I assume you have the latest) as other SPA[35]0x models. I have no problem to set Message Waiting independently. I can't repeat the behavior you described.
    So either your setting is overwritten by remote provisioning, or it's a complex issue related to overall configuration of phone.
    Can you change setting for one extension only ? Have you provisioning configured ? Can you turn on syslog&debug and capture output ?
    It may or may not help to analyze the issue.
    By the way, wrong forum. Your question have nothing to do with XML application. (Updated: has been moved to the correct one)

  • Message waiting indicator isn't going away

    Hello everyone,
    I am having a problem.  My email indicator light won't go off.  I have deleted all email messages from both folders and in fact deleted all messages from all folders and yet I still apparently have an email message that is unread.
    I have gone so far as to delete the email accounts and reset them and still the indicator is there.  Thankfully there is no flashing light, but it is still annoying to see the email indicator.
    I am now utterly confused as to what to do now.  Can someone help me?
    Thanks so much!!

    Some thoughts.
    Have you hidden a message?
    Rather than use the BB, have you gone to your email itself - eg Gmail - and had a look for any unread messages.
    Have you set "on Conflicts" to "Mailbox Wins"
    Hope thats a start.
    Blackberry Best Advice - Back-up weekly
    If I have helped you please check the "Kudos" star on the right >>>>

  • Voicemail waiting indicator will not quit flashing

    I am using the home phone connect and I had a voicemail. I deleted it and the message waiting indicator will not stop flashing. When I go into the menu it says there are no new messages. So I went into the personal options and selected message wating indicator off and the light is still flashing. Emailed customer service and they had me dial *228 and then option 2 for some sort of roaming upgrade. Didn't help the problem. Any one have any ideas? Is there a way to do a total reset?

    try going into your voice mail >option 4>turn message waiting indicator on and off and then toggle between the two options

  • N86 Message Display Indicator is always on

    The Message Display Indicator (the little envelope at the top of the Standby and Menu screens) is always blinking. It has been ever since I got the phone. All the messages in my Inbox have been read. Does anyone know how to turn it off?

    SIM messages. This has already been discussed in the fora many times. Go to Messaging -> SIM msgs. Clear everything you see there. You can copy the messages to your inbox if you want to, or else skip this step.
    Cheers,
    DeepestBlue
    5800 XpressMusic (Rock Stable) | N73 Music Edition (Never Say Die) | 1108 (Old and faithful)
    If you find any post useful, click on the Green "Kudos" Button on the left to say Thank You...

  • Samsung Convoy 3 - Is it possible to store txt message history on the memory card? - Always running out of txt storage space on my phone. I've never gotten close to being able to store 300 messages as indicated on pg 58 of the manual, so I must be missing

    Is it possible to store txt message history on the memory card? - Always running out of txt storage space on my phone. I've never gotten close to being able to store 300 messages as indicated on pg 58 of the manual, so I must be missing something.
    I might get 35 or 40 and then get storage limit warnings

    A_Ohmstede,
    I know it can be frustrating seeing that inbox get full and having to delete
    stored messages.  I do see in the Samsung manual where it advises that it
    will store a maximum of 300 messages on the phone.  The number may lower
    if there are pictures messages and other things being stored on the device.
    Have you checked your total Memory available in Settings and Tools? How much is
    currently available?  Please let us know these details and we may be able
    to help further!
    TrevorC_VZW
    Follow us on Twitter @VZWSupport

  • It's inpossible to use imesage(( I don't no why, always I have message: waiting for activation

    I don't know what's happend but i can't use iMessage. Id correct but I have message: waiting for activation and my phone number is gray and unusable

    Are you using a supported carrier?

  • Message waiting on Lync for Mac

    Hi everyone - I'm hoping someone can help.
    Although I can see I have a message waiting for my on Lync thanks to the number indicator on the app icon, there's no indication of who in my list of contacts actually sent me the message. I have a large list of contacts so it's very laborious to have to
    click through to see who has actually messaged me.
    Has anyone got any ideas of how to fix this?
    Thanks

    Hi,
    Did the issue happen only you or for multiple users?
    Did the issue also happen for Lync client on Windows when login with your Lync account?
    Did the issue happen for all messages you received or for only a few messages?
    Please update to the latest version for Lync server and Lync client from Microsoft Website and test again:
    http://technet.microsoft.com/en-us/lync/dn146015
    Best Regards,
    Eason Huang
    Eason Huang
    TechNet Community Support

  • Message Wait Activity Or Notification Wait Activity for Web Service Wait

    Hi,
    I have a Message Wait Activity Or Notification Wait Activity which waits for a message from my Web-Service. But this Activity keeps on waitinf for the message even if the web-service is down. How do I make it invoke a System Exception if the web-service is down or the web-service cannot be connected?

    Hi,
    I suspect you've put a lot of thought into this and decided to take this approach, but could you describe why you're thinking your web service might be down frequently enough to do this?
    Here's one approach to having the Message Wait activity discover when something outside its control occurs. Put the Message Wait activity inside of one of two transitions going through a Split/Join. For the other transition going through the Split/Join, add a Timer activity (if you are using Oracle BPM 10g). Set the Timer activity to some period that you want to use to periodically hit the web service to ensure it is up (e.g. '5m' to test to see if the web service is up every 5 minutes). Don't have this occur every few seconds or your Engine's performance will be degraded.
    From the Timer activity there would be one transition. This transition leaving the Timer activity would be an unconditional transition going to an Automatic activity. This Automatic activity would have an unconditional transition going back to the Timer activity, and a conditional transition going to the Join activity. The logic in the conditional transition leaving the Automatic activity could be just a single boolean instance variable (e.g. "wsDown"). When the Automatic activity discovers that the web service is down, this copy of the work item instance will flow to the Join activity.
    The logic in the Automatic activity will invoke a dummy web service running on the same machine you're worried about. If an exception is thrown and caught inside the Automatic activity indicating the web service is down, you'd set a boolean flag "wsDown = true".
    The Join activity would have the logic:
    this = copy
    action = RELEASE If the "wsDown" instance variable is set to true when it leaves the Join activity, then the web service was down and the Message Wait activity was never notified from the outside web service.
    Hope this helps,
    Dan

  • Ca'nt ftp longer (i.e. 4 minutes) flv or f4v files (get error message "waiting for server")  I

    when I ftp(i.e. "put" or "upload) short flv or f4v files using dreamweaver cs4 the files upload easily and quickly. However, when I try to ftp ("put" or "upload" ) longer (i.e. 4 minutes or longer) flv or f4v files it goes through the ftp process (seeing it in background activity screen) but at the end I always get a message "waiting on server" and the longer files don't get onto hosting server.  Is there a setting I need to change or other method I need to use).  I have worked with my hosting support tech person but we could not solve this problem.

    I'd suggest that you try using a dedicated FTP program like Filezilla or SmartFTP.
    http://filezilla-project.org/
    Those programs give you much more feedback on what's happening as you attempt to upload files, including error messages, etc.
    There is really no difference between uploading large files and small files, the process on the server is exactly the same..UNLESS there are limits to file size or video duration set by your host. So dispite the fact that you have worked with your host support, I'd still say that the problem is server side or being limited by your Internet service provider... unless the video files you are attempting to upload are corrupted.
    You didn't say if any portion of the larger video files were uploaded...and FTP program will show you whether or not ANY of the file was uploaded and at what point it stopped. You also didn't mention how large the video files where.... sort of where the "tipping point" is in file size (video duration of course is no measure of file size).
    Just to reassure you, the file size of a video file will have no bearing on your ability to FTP unless your host or ISP is limiting you in some way.
    I regularly Live stream events and also record them. An 8 hr event will produce roughly 1.5GB of compressed video. I use SmartFTP, with a reputable host and can upload the entire set of 1.5GB of video files (each about 50MB) over a 1000kbps upload connection without problem. Recently during a movie production project, we uploaded a number of single video file which each where over 1GB a piece.
    So there is really no problem uploading video files unless there are restriction on you account from the host or the ISP.
    Best wishes,
    Adninjastrator

  • SPA 941 VoiceMail message waiting question (Linksys)

    Hi Guys/Girls/Everyone
    I was wondering if anyone can help me, I have a Linksys SPA 941, and am tying to get sipgate.co.uk to provide me voicemail message waiting indication  but they have asked me the below:
    If the device sends a SUBSCRIBE or if it waits for a NOTIFY for message waiting.
    I was wondering if anyone can help answer this for me.
    Thanks

    According to the data sheet, it supports notify/subscribe for mwi.
    http://www.cisco.com/en/US/prod/collateral/voicesw/ps6788/phones/ps10033/ps10038/data_sheet_c78-533409.html
    • Voicemail waiting indicator (VMWI) via NOTIFY, SUBSCRIBE
    This means that the spa will subscribe to the service and be notified when a message is left versus the unsolicited notify method where no subscription takes place.

  • My iphone 3GS no longer syncs with iTunes. The phone is recognised, backs up but then I get an error message: "Waiting for changes to be applied". BUT unlike other people, it doesn't stay stuck on it, instead the process closes down immediately

    Hi all,
    Apologies: I've just joined the community and didn't quite figure how to write a msg! Hope it works...
    Anyway,
    I read many posts on this annoying error message (Waiting for changes to be applied) in the last 2/3 days, but they all refer to the sync staying stuck on it.
    Mine doesn't.
    I read the message, then it quickly shuts down the sync and the iTunes progress bar only shows the apple...
    As suggested by many, I removed voice msgs, turned off/on, tried to sync in individual stages (calendar only...) but nothing works.
    I am up to date on iTunes (11.1.1.11) and have IOS 6.1.3 on my phone, to sync on a Win8 pc (all worked fine until recently).
    I have had this phone for several years and it has never done this.
    It worked absolutely fine, until I loaded the latest version of iTunes it seems...
    Any suggestions?
    Many thanks

    ALSO, on the iPod under Settings>General>iTunes Sync, you may need to back out of the "iTunes Wi-fi Sync," and reopen it to get it to update.
    (I use iTunes 11.1.5.5)

  • If I click on an e-mail address link in a web page instead of a blank message opening I always get a pop up screen with a log-in for googlemail. I do not have and do not want a googlemail account. I just want to be able to send e-mails using Outlook.

    If I click on an e-mail address link in a web page instead of a blank message opening I always get a pop up screen with a log-in for googlemail. I do not have and do not want a googlemail account. I just want to be able to send e-mails using Outlook.

    OUtlook was already set as the mail client for FF, and is my operating system (XP)'s default mail programme. therefore problem not solved at all. what I get whenever I follow a link in a webpage to send an e-mail is a little pop up window asking me to sign in to gmail or open an account. any other suggestions?

  • I have a Laserjet 2550L. When I try to print 2nd time get message "Waiting for printer to become ava

    Laserjet 2550L being used with Mac OSX Lion 10.7.3. After turning on, it will print once. When trying to print a second time I get a message "waiting for printer to become available." I have to turn it off and then back on to get it to print again.

    Hum. Let's uninstall with the 'scrubber option' like this:
    1. Go to Applications/Hewlett Packard/ click on HP Uninstaller and click Continue
    2. Highlight your device on the left pane
    3. Hold the Ctrl, Opt and Cmd keys and click on Uninstall
    4. There will be a pop up that asks if you are sure you want to uninstall ALL hp software. (At this point, if you continue, any HP printers you have installed will need to be reinstalled)
    5. Click Continue and let it finish
    Now, run a Software Update. This can be done by clicking the Apple in the top left of the screen then clicking Software Updates.
     Next, let's reset the printing system:
    Go to System Preferences > Print & Scan
    - Right (or control) click in the rectangle listing your printers and select Reset Printing System.
    WARNING - this will delete ALL of your printers!
    - Select the plus sign to re-add a printer. Select the Default tab on the top of the window. Look for the printer, select it and wait until the "Add" button becomes available. Click it.
    Let me know how this works for you.
    -------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

Maybe you are looking for