SPA3102 questions

Hey all, I just read the admin guide for the SPA 3102 but I wanna make sure I didn't misunderstand anything so, could someone confirm that I can do all the stuff below, and note I'm in the UK.
1. Register 1 voip provider (VA) for outgoing calls, 1 different voip provider (VB) for incoming calls, and connect 1 pstn line for incoming calls.
2. Connect a single analogue phone and recieve calls on it automatically from anyone calling either my voip (VB) or pstn number, with Caller ID from either being presented correctly.
3. Make calls on the same phone via either the voip (VA) or pstn line (with Caller ID being sent correctly).
4. Automatically decide which of VA or PSTN I want to go out with by dialplans, down to specific numbers (eg. all 0800 go out pstn, all starting 07, 01, 02 out via VA, 999 out PSTN, 0113212121 out PSTN). And fallback to PSTN on voip failure or power loss to spa.
5. Any form of recording how many calls have been made, and whether these went out via PSTN or VA (and possibly if they were successful or not)? Or any information that could allow a list of these calls to be made? Just saw in the user guide there seems to be only 1 field for Last Number Called for both voip and PSTN, maybe a script could monitor this for changes and update a list on every change, then i'd have a list of all numbers dialed but not if they were succesful or not...
6. A fun one - gain telnet/ssh access and change dialplans via the command line, even create a script on the thing to check dialplans and dialed numbers and change dialplans automatically (I want to do this based on number of pstn calls made to get around bt's "6 chargeable calls per quarter or we charge you for caller id" rule, and preferably do it via script automatically cos i'm geeky like that, though I could script on my wrt54g and have it telnet to an ata but only if i can...).
Thanks for the help, pepsi_max2k
oh ps, i'm loving the amount of threads i'm finding in google on problems with the spa3102 in the uk, followed immidiately by "it's fine now, just did (insert very simple external fix - new cable / mf / phone) and it works great" type posts if only all hardware fixed itself as easily as this thing seems to
Message Edited by pepsi_max2k on 06-01-2008 04:29 AM

thanks for that so basically, yes, it does everything i asked other than pstn fallback when voip fails. i can deal with that well, there is the no ssh thing that sucks a bit. other than multi voip accounts it then means my speedtouch is just as good (actually better as it has telnet access and logging, although only for voip calls).
i just got a cheap fritzbox 5050 so i'm gonna see what I can do with that, hopefully i can get some decent dialplans working, and if it does everything else above then i'll be chuffed. I know it does telnet, dunno if i can grab textual call stats from there but there's gotta be a way, i know it does very detailed stats though (esp. for pstn), multi voip accounts (both in and out), CLIP should be ok so long as I can get wiring right, dialplans seem a bit simple but might just allow me to do what I want (again whether I can change these via telnet I'm not sure)...
Anyway, still might get an SPA just as it seems pretty reliable, and I know what it can / can't do
Message Edited by pepsi_max2k on 06-03-2008 08:34 AM

Similar Messages

PAP2, SPA3102, WIP330 questions

Hello, I dont know pretty much in voip telephony, so please clear for me some issues =) 1) Are pap2 and spa3102 doing the same thing - transferring phone call from internet connection to regular home phone? Whats the difference between them? 2) can I use those devices without PC, just with internet connection? I wanna use voipstunt provider and they give me just username, so nobody will be able to call me from say, cell phone, just from the same application (voipstunt) from PC? 3) If I configure WIP330 with my voip provider, will I be able to make calls from anywhere where a hot-spot is present without PC? Do i need to get phone number from my voip provider? Thank you.

you can pretty much use the devices without a PC< but you will need a PC to configure the PAP2 and the SPA3102
the WIP can be used on a hot spot, and when registered to a voip provider, can pretty much give you IP phone access.
you may need to pay extra to have your regular calls routed to your voipstunt account.

P2P SPA3102 setup with no SIP server/service provider

Description:
- Peer-to-peer ATA connection with no service provider or SIP server
Location A (my location):
- Linksys SPA3102
- PABX analog device (Panasonic)
- Public and static IP
Location B (my partner location):
- D-Link DVG2001S
- Public IP
Questions:
- Can B ATA (D-Link) call to A ATA (Linksys) being different brands?
- Can I pick up the B ATA attached phone and directly to have PABX internal dial tone at A, for other extension or external calls?
- From PABX other extensions, can I call to SPA3102 extension number and directly redirect the call to B ATA?
I was read many .pdf documents about SPA setup, and try differents configuration, but I'cant make the communication with my partner location happens.
I think my problem is understanding and writing the correct PSTN LINE and LINE 1 Dial Plan parameters in my SPA3102.
Can I make it happens?
Thanks in advance,
Bitman
Message Edited by Bitman on 07-28-2007 05:37 AM

Good day! I just hope this is not one of those “.pdf documents” that you have already read but basically this should work if you’re setting up two SPA3000 or SPA3102 since they have exactly the same Voice configuration:
http://www.provu.co.uk/pdf/sipura/spa_backtoback_2x_spa3000.pdf
I’m guessing that IP dialing should work on your two units if they both support SIP, however, in this case, I haven’t tried setting up a D-Link before ( or you may try to wait for other users who happen to have a D-link also to post suggestions) , you may just want to try looking for documents on setting up IP dialing on D-link then try to match it’s IP dialing parameters with the SPA.

SPA3102

I have some questions as below listed:
1. Is SPA3102 can handled more than one call session at moment?
2. How can i share the VoIP account in the LAN for other users?
3. How many IP phones can connect to one SPA3102 for concurrent call sessions? (we have only one VoIP carrier account from lowratevoip.com)
4. please let me have a solution for multiple users and concurrent calls in the LAN with one VoIP carrier account?

1. Is SPA3102 can handled more than one call session at moment?
the SPA3102 can handle 2 lines for line 1 , 1 for main call and 1 for call waiting.
from the analog phone, you can also setup a dial plan for dialing out to 4 other gateways. the PSTN line has a 1 gateway call.
2. How can i share the VoIP account in the LAN for other users?
if you have for that one ATA, you can set those others to make call without regsiter to yes and answer call to yes, and regsiter to no.
3. How many IP phones can connect to one SPA3102 for concurrent call sessions? (we have only one VoIP carrier account from lowratevoip.com)
this one is not possible. the SPA3102 cannot be used as a voip gateway or PBX
4. please let me have a solution for multiple users and concurrent calls in the LAN
with one VoIP carrier account?
consider the SPA9000 PBX system that can can have mutiple sessions depending on the trunk line provided by the VOIP provider for you.

SPA3102 Help needed

I have two questions on PSTN connections with the SPA3102. I tried the Linksys Support chat, but the agent there said he wasn't qualified to help and couldn't pass me on to someone who could help - very disappointing!
Here are my questions (I'm in the UK):
Q1 - Can I set the SPA to pass through the telco's PSTN dialling code, instead of presenting me with its own tone? This is so that I can hear the interrupted dialling tone that indicates a message waiting.
Q2 - The SPA seems very slow to pick up an incoming PSTN call. I have not found any setting that will adjust this delay. Is there one?
If someone here could help me I would be very grateful.

RG99 wrote:
Q1 - Can I set the SPA to pass through the telco's PSTN dialling code, instead of presenting me with its own tone? This is so that I can hear the interrupted dialling tone that indicates a message waiting.
I have seen some discussion about how to do this if you are calling from the phone attached to line 1 but I don't think that technique will work when you come into the adapter over the pstn tab. The adapter really was designed to have you enter the dialing digits, then the adapter edits the digits with the dial plan and then sends the digits. Maybe someone knows how to circumvent SPA's dial plan, however it wasn't the way the adapter was designed.
Q2 - The SPA seems very slow to pick up an incoming PSTN call. I have not found any setting that will adjust this delay. Is there one?
The principal adjustment for the timing for the pstn-to-voip adapter to pickup an incoming pstn call is the PSTN Answer Delay. The principal adjustment for the timing for the voip-to-pstn adapter to pickup an incoming voip call is the VoIP Answer Delay.

SPA3102: Can I route a POTS line to a SIP phone?

I need to temporarily get POTS service where there is, well, nothing. My idea is to use an SPA3102, a wireless link and a SIP phone (all of which I have) to solve the problem. At the required phone location, I would just have a SIP phone connected to a WiFi link.
At the other end of the link would be the SPA3102. It's only connections would be to the WiFi link radio and the POTS line. No internet involved.
First question: Can I do this? If yes, second is how as in how do I configure the SPA3102? If would be great if picking up the SIP phone got POTS dialtone but not mandatory. But, it clearly is mandatory that an incoming POTS call would ring the SIP phone.

There is no network beyond the pieces I listed. The two ends look like this:
Local: POTS line, SPA3102, wireless link radio
Remote: wireless link radio, SIP phone
The radio link is point-to-point and effectively can be ignored for the configuration. That is, a POTS line, SPA3102 and SIP phone hooked together would look effectively the same and this is how I will test the system before deployment.
As there is no external/internet connection, the IP addresses are arbitrary. Clearly, adding a computer with web browser to the system for configuration purposes is needed but, once again, the IP address is arbitrary. My guess (and it is just that) is that the computer can be plugged into the Ethernet port and the SIP side into the Internet port so no Ethernet hub would be needed but that is a guess.

Newbie - Setting up the SPA3102

Hi,
Sorry for the basic questions, but am brand new to VOIP !
I bought a SPA3102 and it was delivered yesterday, I plugged the DECT phone base station into the telephone port and connected the line to the wall jack.
Firstly, powering up the device, and typing #### on the handset gets me the BT messgae saying the number is not recognised. Only when I disconnect the unit from the wall jack and redoing the #### gets me the linksys welcome message. Is this correct behaviour ?
Secondly, I already have a linksys (WRT54G I think) wireless gateway. Can I connect both the ethernet and internet ports on the SPA3102 to free ports on the WRT54G, as would prefer to continue to use the gateway for its ADSL modem, dhcp server and routing ?
Lastly, is it then also correct to wire the telephone output of the WRT54G to the adsl side of the telephone filter, and the SPA3102 to the usual telephone side of the filter ?
Any help would be much appreciated.
Thanks !!

There is no reason to connect both internet and ethernet ports, unless I missed something setting up mine.
It is possible but you'd need to disable the DHCP server on the LAN side of the SPA (assuming your WAG is running as your DHCP server), but I really don't see any benefit in doing this.
Dialing STD calls depends on your Dial Plan, but I think it's good practice to need to.
Michael
Message Edited by Swiftnets on 09-03-2007 01:45 PM

Spa-3102 Feature Question

Hello
I was wondering if the following setup is supported.
I would call a skype id and then using the spa3102, that id would use the fxo port and give a off hock status and then I would be connected to that line
is this supported/been done before?
thank you

I didn't read your questions carefully enough the first time.
The EXT IP: address is the external ip address of the SPA3102 itself, not the opposite one.

Quick question from a newbie

I want to set up VOIP trunk between two fixed location. Location A is home while location B is work. There is a VPN between the two, they are on different subnets. I want to access the PSTN line at site B (work) from Site A (home) using VOIP. In other words I want to use the PSTN at work to make voice calls when I work from home.
Can I just install SPA3102 in work and use SPA901 at home. No SIP server just direct trunk between the two. In other wods can I just "dial" the SPA3012 using the SPA901 and get a PSTN dial tone. No other devices will be involve just point to point between these two.
Is this possible, is it easy to set up?
Many thanks
Peter
Solved!
Go to Solution.

I found teh answer in the excellent "SPA3000 bac to back document". It seems this question has been asked many times apologies, for those new to VOIP it as much knowing what question to ask and what to actually search for!
Anyway sorted

SPA3102 + Telfort NL

My ADSL provider recently changed their voip system from ritstele.com to telefoniedienst.nl.
Can anyone assist with translating the following settings to the SPA3102?
SIP proxy: sip.telefoniedienst.nl
SIP service location: sip.telefoniedienst.nl
SIP signaling port: UDP 5060
SIP register service location: tel.telefoniedienst.nl
SIP register signaling port: UDP 5060
SIP domain: tel.telefoniedienst.nl
URL type coding: SIP
Registration interval: 6000 seconds
Session expires: 1800 seconds
Reserved RTP port range: UDP 16384-32767
Codecs: First negotiated G.729 secondly negotiated G.711 a-law type
DTMF mode: PCM
Sending INVITE Anonymous: Not permitted
Echo Cancellation G.168: In use
Voice Activation Detection: Not in use
SIP SUBSCRIBES messages: Not permitted
Early Media acknowledge: Not in Use
Below is some information from my syslog:
System started: [email protected], reboot reason:H30300010 YM:AuthServerIp[0]=c3f04842
YM:AuthServerIp[1]=c3f04841
YM:Connecting[0]c3f04842:5060
YM:skt=10 [0]Reg Addr Change(0) 0:0->c3f04842:5060 [0]->195.240.72.66:5060(552)
[0]195.240.72.66:5060(387)
[0]195.240.72.66:5060(528)
[0]->195.240.72.66:5060(768)
[0]195.240.72.66:5060(405)
### tcp connect failed
YM:Connecting[1]c3f04841:5060
YM:skt=11 ### tcp connect failed
YM:Connecting[0]c3f04842:5060
YM:skt=12
My main questions are where to put the SIP Domain and where to put the SIP register service.
With kind regards,
Arjen
P.S. For those of you that already read my previous post: sorry about reposting but the previous post looked like ****.

My best guess (I could be wrong) would be:
Line 1 tab:
Sip Proxy: tel.telefoniedienst.nl
Outbound Proxy: sip.telefoniedienst.nl
Use Outbound Proxy: YES
However this blog says just to use
Sip Proxy: tel.telefoniedienst.nl
http://planet.livecd.net/
Check the INFO tab to see if it registers. If it does try a test call
It looks like both tel.telefoniedienst.nl and sip.telefoniedienst.nl currently have the same ip addresses, i.e. 195.240.72.65 or 195.240.72.66.
The trace says you are sending the request to 195.240.72.66 but it doesn't show a reply coming back from them.
To see a full debug trace I would run with
Sip Debug Option: Full on the Line 1 tab
Debug Level: 3 on the Sip Tab
This will let you see the format of the register request and later the sip invite.
The fact you are not getting a reply could be due to the format of the data in the Register request, or it could be something to do with your router.

Questions on Print Quote report

Hi,
I'm fairly new to Oracle Quoting and trying to get familiar with it. I have a few questions and would appreciate if anyone answers them
1) We have a requirement to customize the Print Quote report. I searched these forums and found that this report can be defined either as a XML Publisher report or an Oracle Reports report depending on a profile option. Can you please let me know what the name of the profile option is?
2) When I select the 'Print Quote' option from the Actions drop down in the quoting page and click Submit I get the report printed and see the following URL in my browser.
http://<host>:<port>/dev60cgi/rwcgi60?PROJ03_APPS+report=/proj3/app/appltop/aso/11.5.0/reports/US/ASOPQTEL.rdf+DESTYPE=CACHE+P_TCK_ID=23731428+P_EXECUTABLE=N+P_SHOW_CHARGES=N+P_SHOW_CATG_TOT=N+P_SHOW_PRICE_ADJ=Y+P_SESSION_ID=c-RAuP8LOvdnv30grRzKqUQs:S+P_SHOW_HDR_ATTACH=N+P_SHOW_LINE_ATTACH=N+P_SHOW_HDR_SALESUPP=N+P_SHOW_LN_SALESUPP=N+TOLERANCE=0+DESFORMAT=RTF+DESNAME=Quote.rtf
Does it mean that the profile in our case is set to call the rdf since it has reference to ASOPQTEL.rdf in the above url?
3) When you click on submit button do we have something like this in the jsp code: On click call ASOPQTEL.rdf. Is the report called using a concurrent program? I want to know how the report is getting invoked?
4) If we want to customize the jsp pages can you please let me know the steps involved in making the customizations and testing them.
Thanks and Appreciate your patience
-PC

1) We have a requirement to customize the Print Quote report. I searched these forums and found that this report can be defined either as a XML Publisher report or an Oracle Reports report depending on a profile option. Can you please let me know what the name of the profile option is?
I think I posted it in one of the threads2) When I select the 'Print Quote' option from the Actions drop down in the quoting page and click Submit I get the report printed and see the following URL in my browser.
http://<host>:<port>/dev60cgi/rwcgi60?PROJ03_APPS+report=/proj3/app/appltop/aso/11.5.0/reports/US/ASOPQTEL.rdf+DESTYPE=CACHE+P_TCK_ID=23731428+P_EXECUTABLE=N+P_SHOW_CHARGES=N+P_SHOW_CATG_TOT=N+P_SHOW_PRICE_ADJ=Y+P_SESSION_ID=c-RAuP8LOvdnv30grRzKqUQs:S+P_SHOW_HDR_ATTACH=N+P_SHOW_LINE_ATTACH=N+P_SHOW_HDR_SALESUPP=N+P_SHOW_LN_SALESUPP=N+TOLERANCE=0+DESFORMAT=RTF+DESNAME=Quote.rtf
Does it mean that the profile in our case is set to call the rdf since it has reference to ASOPQTEL.rdf in the above url?
Yes, your understanding is correct.3) When you click on submit button do we have something like this in the jsp code: On click call ASOPQTEL.rdf. Is the report called using a concurrent program? I want to know how the report is getting invoked?
No, there is no conc program getting called, you can directly call a report in a browser window, Oracle reports server will execute the report and send the HTTP response to the browser.4) If we want to customize the jsp pages can you please let me know the steps involved in making the customizations and testing them.
This is detailed in many threads.Thanks
Tapash

Satellite P300D-10v - Question about warranty

HI EVERYBODY
I have these overheating problems with my laptop Satellite P300D-10v.
I did everything I could do to fix it without any success..
I get the latest update of the bios from Toshiba. I cleaned my lap with compressed air first and then disassembled it all and cleaned it better.(it was really clean insight though...)
BUT unfortunately the problem still exists...
So i made a research on the internet and I found out that most of Toshiba owners have the same exactly problem with their laptop.
Well i guess this is a Toshiba bug for many years now.
Its a really nice lap, cool sound (the best in laptop ever) BUT......
So I wanted to make a question. As i am still under warranty, can i return this laptop and get my money back or change it with a different one????
If any body knows PLS let me know.
chears
Thanks in advance

Hi
I have already found you other threads.
Regarding the warranty question;
If there is something wrong with the hardware then the ASP in your country should be able to help you.
The warranty should cover every reparation or replacement.
But I read that you have disasembled the laptop at your own hand... hmmm if you have disasembled the notebook then your warrany is not valid anymore :(
I think this should be clear for you that you can lose the warrany if you disasemble the laptop!
By the way: you have to speak with the notebook dealer where you have purchased this notebook if you want to return the notebook
The Toshiba ASP can repair and fix the notebook but you will not get money from ASP.
Greets

Question regarding NULL and forms

Hi all, i have a survey that im working on that will be sent via email.
I'm having an issue though. if i have a multiple choice question, and the user only selects one of the choices, all the unselected choices return as NULL. is there a way i can filter out anytihng that says "NULL" so it only shows the selected options?
thanks.
here is the page that retrieves all the data. thanks
<body>
1) Is this your first visit to xxxxxxx? <%=request.getParameter("stepone") %>

 
2) How did You Learn About xxxxxxx?
<%=request.getParameter("steptwoOne") %>
 
 <%=request.getParameter("steptwoTwo") %>
 
 <%=request.getParameter("steptwoThree") %>
 
 <%=request.getParameter("steptwoFour") %>
 
 <%=request.getParameter("steptwoOther") %>

 
3) What was your main reason for visiting xxxxx?
<%=request.getParameter("stepthreeOne") %>
 
 <%=request.getParameter("stepthreeTwo") %>
 
 <%=request.getParameter("stepthreeThree") %>
 
 <%=request.getParameter("stepthreeFour") %>
 
 <%=request.getParameter("stepthreeOther") %>

4) did you find the information you were looking for on this site?
<%=request.getParameter("stepfour") %>
 
<%=request.getParameter("stepfourOther") %>

5) Do you plan on using this website in the future?
<%=request.getParameter("stepfive") %>
6) What is your gender
<%=request.getParameter("stepsix") %>
7) What is your age group
<%=request.getParameter("stepseven") %>
8) Would you like to take a moment and tell us how we can improve your experience on xxxxxxxxxx?
<%=request.getParameter("stepeightFeedback") %>

i was messing around and came up with this. it doesnt remove the null, but if it is null it adds ABC beside it. so i think i might be getting close. i just need to figure out how to replace the null.
code]
<%=request.getParameter("steptwoFour") %>
 <% if (request.getParameter("steptwoFour") == null ) {
 %>
 <% out.print("abc"); %>
 <% }
 %>

Anyone know how to remove Overdrive books from my iphone that have been transferred from my computer? They do not show up on itunes. I see a lot of answers to this question but they all are based on being able to see the books in iTunes.

How do I remove Overdrive books from the library that were downloaded onto my computer then transferred to my iphone? The problem is that they do not show up in iTunes.
I see this question asked a lot when I google, but they always give answers that assumes you can find the books in iTunes either under the books tab, or the audio books tab or in the music. They do not show up anywhere for me. They do not remove from the app like the ones I downloaded directly onto my iphone.the related archived article does not answer it either. I even asked a guy working at an apple store and he could not help either. Anybody...?
Thanks!

there is an app called daisydisk on mac app store which will help you see exactly where the memory is focused and consumed try using that app and see which folders are using more memory

Basic question

Hello, i have a basic question. if i have defined 2 fields in a cube or a dso:
Name Quantity
and from the external flat file i get some characters for my quantity field. would my load fail? for standard dso and for write optimized?
NOTE: quantity field is a keyfigure defined as numeric.
and the load coming in has "VIKPATEL" for Quantity field and not numbers.
thanks

Hi Vik,
Yes, the load will fail.
May be you coud first load this data into BW (into PSA) and set both fields as characters fields. Then you can create DSO, do transformation from this PSA to the DSO, and put your logic as to what do you want to do with those Quantity that is not number (e.g. convert to 0, or 'Not assgined', etc).
You can use transfer rule, or a clean up ABAP code in the start routine.
Hope this helps.

SPA3102 questions

Similar Messages

Maybe you are looking for