SPA3102 when NAT is off I cannot connect to graphic interface

Hello,
With my SPA3102 when NAT is off (bridged) I cannot reach the graphic interface any more. Is this normal? I discovered that I need to have NAT off because of a utility I'm running to connect me to an Outlook.pst file elswhere. NAT is translating port numbers and that is exactly what should not be.
Greetings to all,
Basil de Visser, Amsterdam

I had the same problem. Drove me nuts, did not act the same way as other SPA products. Okay, here is what I did more specifically.
Admin, Advanced menus. On the WAN tab, I set it for DHCP (assiming that you have a router or other device on your LAN handling DHCP requests). On the same screen, set "Enable Web Server" to Yes.
On the LAN Setup tab, set the Networking Service: setting to Bridge. Remove the power and power back up. Once it is back up. dial **** from the phone and enter option 110# and it will give you the IP address that the WAN port was given by your DHCP server. Log into that address with your browser and it should work.
Mark
Ball Ground, GA

Similar Messages

HT1923 When trying to access i tunes store when in I Tunes i cannot connect to the internet - any thoughts? i have tried un-installing and re-installing but no joy

When trying to access i tunes store when in I Tunes i cannot connect to the internet - any thoughts? i have tried un-installing and re-installing but no joy

Close your iTunes,
Go to command Prompt -
(Win 7/Vista) - START/ALL PROGRAMS/ACCESSORIES, right mouse click "Command Prompt", choose "Run as Administrator".
(Win XP SP2 n above) - START/ALL PROGRAMS/ACCESSORIES/Command Prompt
In the "Command Prompt" screen, type in
netsh winsock reset
Hit "ENTER" key
Restart your computer.
If you do get a prompt after restart windows to remap LSP, just click NO.
Now launch your iTunes and see if it is working now.
If you are still having these type of problems after trying the winsock reset, refer to this article to identify which software in your system is inserting LSP:
iTunes 10.5 for Windows: May see performance issues and blank iTunes Store
http://support.apple.com/kb/TS4123?viewlocale=en_US

Photosmart 5510 printer model #B111A when using touchscreen apps i cannot connect to the server

Photosmart 5510 all-in-one printer, model #B111A, windows XP----i can print from the computer, but when i try to use the apps on the touchscreen i get a message error "cannot connect to the computer"

The steps below typically resolve the issue you’re experiencing:
1. Unplug the power cord from the back of the printer.
2. Unplug the power cord from the back of your router (and modem, if separate from the router).
3. Wait 20 seconds, then plug the router (and modem, if applicable) back in.
4. Wait 30 seconds, then plug the printer back in and power it on.
5. Press the ePrint button on the printer's front panel, and it should try to connect to Web Services again.
Those steps usually resolve the issue, but if it still occurs you can try setting static network info for the printer (which sometimes helps to stabilize the printer's ability to get outside of your network, to the internet):
1. Press the wireless icon at the top of the printer's screen and note the IP address.
2. Enter the IP address into the address bar of a web browser on a computer and press enter or click the browser's go button.
3. The printer status page should be opened. Click on Network at the top.
4. Click on Networking on the left.
5. Select Proxy Settings.
Note: If you are prompted for a redirect, select OK. If you receive a certificate warning, select the option that lets you continue anyway.
If you receive a Internal System Error, refresh the page until it loads the proxy settings.
6. Verify that all fields are blank. If they are not, clear them and make sure the Proxy Server requires authentication is unchecked and click apply. You should get a success message.
7. Click on Network Address (IP) on the left.
Note: If you only see IP Address Configuration and DNS Address Configuration with a yellow note, refresh the page until it loads completely.
8. Leave the IP Address Configuration as Automatic IP.
9. Change DNS Address Configuration to Manual DNS server.
10. Enter 8.8.8.8 for the Manual Preferred DNS Server and 8.8.4.4 for the Manual Alternate DNS Server.
11. Click Apply and you should get a success message.
12. Power off the printer for 30 seconds and then turn it back on to force the new settings to take effect.
If I have SOLVED your issue, please feel free to provide KUDOS and make sure you mark this thread as SOLUTION PROVIDED!
Although I work for HP, my posts and replies are my own opinion and not those of HP.

Is anyone having stuttering problems on the ati 5870 with the mini dislplayport connected monitor when you turn off the display connected to the Dual-link DVI port?

hey i have a ATI 5870 and when ever i turn the monitor connected to the dual_link DVI port the display connected to one of the mini display port shutters with everything on the screen Video, Mouse movement ect, any ideas ?

hey i have a ATI 5870 and when ever i turn the monitor connected to the dual_link DVI port the display connected to one of the mini display port shutters with everything on the screen Video, Mouse movement ect, any ideas ?
Not sure what you are trying to do. I interpret what you are saying is that you have a monitor connected to the DVI port and another to the mini displayport (mDP). Are you physically trying to turn the one connected to the DVI port off (and on) causing the one on the mDP port to "shutter"? If so, take a look at SwitchResX. It will allow you to programmatically turn monitors on or off. Maybe that will cure the problem.
Of course if I am misinterpreting what you are saying ignore this post.

When my iPhone is off, I cannot connect to charger

meu iphone ESTA desligando Sozinho e when Desliga assim Consigo Ligar ELE não Carregador
<Edited By Host>

If your iPad is disabled due to misentry of a passcode, you must restore it via recovery mode by following the instructions in http://support.apple.com/kb/HT1212 but f you do not have a computer you can use, you may be able to get help by visiting an Apple store genius bar and see if they will do the restore for you.

Can't finish upgrade on atv, when verifying with iTunes says cannot connect to update server. Help!

When upgrading my atv I can't seem to connect to the apple update server. Wondering if I. Need to change my host file and if so how do I do that?

Welcome to the Apple Community.
If your problem persists get yourself a micro USB cable (sold separately), you can restore your Apple TV from iTunes:
Remove ALL cables from Apple TV. (if you don't you will not see Apple TV in the iTunes Source list)
Connect the micro USB cable to the Apple TV and to your computer.
Open iTunes.
Select your Apple TV in the Source list, and then click Restore.

I phone 4s I downloaded os 7.1 and now I cantt make in app purchases when I try it says cannot connect to iTunes anyone know what I can do

I've got an iPhone 4s I just downloaded the iOS 7.1 now I'm unable to make in app purchases can someone help me out please

What exactly are you being prompted when it declines your in App purchases?

When updating apps, iPad says "cannot connect to iTunes"

I can't update my apps, help!

You can try rebooting your router - unplug it for about 30 seconds and then plug it back in.
Or restart the iPad. Restart the iPad by holding down on the sleep button until the red slider appears and then slide to shut off. To power up hold the sleep button until the Apple logo appears and let go of the button.
Or temporarily disable your firewall and security software.
Look through this for help as well.
http://support.apple.com/kb/ts1368

My ipod touch is locked i am trying to restore it however when itunes tells me it cannot connect because the ipod is locked there is no place on itunes that shows "devices" as it says in the restore orocedures now what?

my ipod touch is locked i am trying to restore it nut when itunes tells me it does not recognize it , however, there is no place on the itunes screen that lists devices like the procedures tell you

Place the iPod in recovery mode and then restore the iPod via iTunes. For recovery mode see:
iPhone and iPod touch: Unable to update or restore

I have been getting notices about an important security update for a month now and when I click update, I cannot connect to the server.

I am using a mac... Have downloaded new version. Is all I need to do to Drag Firefox from Applications to trash to uninstall? Do I still need to also delete Program Folder? If so, where can I find it?

If there are problems with updating or with the permissions then easiest is to download the full version and trash the currently installed version to do a clean install of the new version.
Download a new copy of the Firefox program and save the disk image (dmg) file to the desktop
*Firefox 16.0.2: http://www.mozilla.org/en-US/firefox/all.html
*Trash the current Firefox application (e.g. open the Applications folder in the Finder and drag the Firefox application to the Trash) to do a clean (re-)install
*Install the new version that you have downloaded
*https://support.mozilla.org/kb/Installing+Firefox+on+Mac
Your profile data is stored elsewhere in the Firefox Profile Folder, so you won't lose your bookmarks and other personal data if you uninstall and (re)install Firefox.
*http://kb.mozillazine.org/Profile_folder_-_Firefox

Airport Extreme: PEAP authentication failure when NAT is enabled

Setup: Airport Extreme firmware 5.6, Windows Admin Utility 5.2
Airport's WAN port connected to an internal network with Windows 2003 IAS RADIUS server; Airport's LAN port disconnected.
Windows XP client (using Microsoft zero-configuration client)
client and server set up to use PEAP authentication
If I set up the Airport in bridge mode (uncheck the "Distribute IP Addresses" box in the Network setup tab), the client can authenticate correctly and can obtain an IP address from a DHCP server on my internal network.
If I check the "Distribute IP Addresses" box, select "Share a single address with DHCP & NAT" and the 192.168.1.1/24 address range, the client can no longer authenticate. I haven't changed anything else on either the Airport or the RADIUS server.
Network traces taken on the wired (WAN) and wireless side of the Airport show that the first few exchanges of the EAP handshake go through fine, but the server's reply to the client's "TLS Hello" message are being blocked by the Airport. Up to that point, I don't see any significant difference between the exchanges with NAT enabled or disabled; it's just that the Airport passes the server's message to the client correctly when NAT is off and blocks it when NAT is on.
Airport Extreme Windows XP

My mistake - posted to the wrong forum! I've restarted the thread on the Airport Extreme forum.

AHHHHHHH! Install cannot connect to database error!

I am so frustrated with application server install...
I'm trying to install SOA 10.1.3, advanced option, 1st option
When it asks me for database account, host name, service name I enter all this info in then i click next...
This is when I get the Install cannot connect to database error even though db i'm trying to connect to is on same machine!
Anyone have any ideas other than laying off medication as to what the problem is?

Check the requirement chapter in the Installation Guide, but it should be similar to:
127.0.0.1 localhost.localdomain localhost
192.168.1.88 yourserver.domain.com yourserverHowever, I don't think you should change any of this after a installation...

Macbook pro cannot connect to wifi

before i let apple fix my laptop cos of the malware, the wifi works fine. then i got my laptop last monday and i tried connecting to the wifi in the apple store and it worked okay. when i got home, i cannot connect to my wifi anymore. well it can detect the wifi but it usually states connection timeout and invalid password (rarely when i keep on connecting to the network even though its the right PW) then when i finally get connected, it'll be like NO INTERNET CONNECTION and this "!" will show up in the middle of the wifi status...
please help.

and how do you do that "Power cycle the modem, router and your MBP." ? thanks!
btw, my other laptop which is a windows can detect our wifi and it has excellent connection . >( so its really stressful. please help!

Cannot connect to abap server, please check your abap server connection

Installed new NW BPC 7.5 system on windows 2008 server but get the error as follows
when logon to BPC server:
"Cannot connect to abap server, please check your abap server connection".
"define system user group tab" is inactive in server manager also.
Server Diagnostic errors for SAP Server Connection:
Database Connection
Status Connection Error
as per note 1385864 but this note has not helped get past this status with installation.
User Type value is either set to Communication Data for all three users (BPC_ADMIN, BPC_SYSADMIN, BPC_USER).
and these accounts are not locked.
Any ideas for these errors?
Regards,
Aidan

Hi Aidan,
"Your logon id (domain\user) does not have SystemAdmin rights; some functionality
is disabled."
This is caused by the fact that the user you are logged in as isn't in the UJA_SVR_DEFAULT table, the SYSADMIN field needs to have a value that contains your user id (i.e. DOMAIN\USER) . You can set this up with the UJA3_WRITE_SYS_USERS program.
"When I try to install APPshell the following errors occur:
@8O@ UJA_DATA_CHECK E 006 Application PLANNING's multiprovider /CPMB/ATMKOOE not exist in BW
@8O@ UJS_EXCEPTION E 003 Errors occured during "after import" method call during activation"
Aidan, sounds like something went terribly wrong during your activation process. Do this, Clean the appset with the UJS_ACTIVATE_CONTENT program and make sure that everything is completely deleted. Make sure that there is a lot of memory available for the activation and try it again.
It should work.
Hopefully this helps you.
Cheers, Scott

Cannot connect Service Manager with Orchestrator Web Service URL

Dear TechNet User,
i cannot connect my service manager console with my Orchestrator Webservice. i try to connect to "http://AMSCO01:81/Orchestrator.svc" ... the user i´ve choose is local admin on the orchestrator Machine.
Thats the Logfile:
Date: 07.10.2013 15:23:16
Application: System Center Service Manager
Application Version: 7.5.2905.0
Severity: Error
Message: Could not connect to the Orchestrator web service.
System.Data.Services.Client.DataServiceQueryException: An error occurred while processing this request. ---> System.Data.Services.Client.DataServiceClientException: <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Strict//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-strict.dtd">
<html xmlns="http://www.w3.org/1999/xhtml">
<head>
<meta http-equiv="Content-Type" content="text/html; charset=iso-8859-1"/>
<title>404 - File or directory not found.</title>
<style type="text/css">

</style>
</head>
<body>
<div id="header"><h1>Server Error</h1></div>
<div id="content">
<div class="content-container"><fieldset>
<h2>404 - File or directory not found.</h2>
<h3>The resource you are looking for might have been removed, had its name changed, or is temporarily unavailable.</h3>
</fieldset></div>
</div>
</body>
</html>
   at System.Data.Services.Client.QueryResult.Execute()
   at System.Data.Services.Client.DataServiceRequest.Execute[TElement](DataServiceContext context, QueryComponents queryComponents)
   --- End of inner exception stack trace ---
   at System.Data.Services.Client.DataServiceRequest.Execute[TElement](DataServiceContext context, QueryComponents queryComponents)
   at System.Data.Services.Client.DataServiceQuery`1.Execute()
   at System.Data.Services.Client.DataServiceQuery`1.GetEnumerator()
   at Microsoft.EnterpriseManagement.ServiceManager.Sdk.Connectors.OrchestratorRunbookConnector.GetRunbookFolders(OrchestratorContext scoContext, Folder parentFolder)
   at Microsoft.EnterpriseManagement.ServiceManager.UI.Administration.Connectors.Orchestrator.OrchestratorConnectorHelper.ValidateServerConnection(Boolean found)
System.Data.Services.Client.DataServiceClientException: <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Strict//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-strict.dtd">
<html xmlns="http://www.w3.org/1999/xhtml">
<head>
<meta http-equiv="Content-Type" content="text/html; charset=iso-8859-1"/>
<title>404 - File or directory not found.</title>
<style type="text/css">

</style>
</head>
<body>
<div id="header"><h1>Server Error</h1></div>
<div id="content">
<div class="content-container"><fieldset>
<h2>404 - File or directory not found.</h2>
<h3>The resource you are looking for might have been removed, had its name changed, or is temporarily unavailable.</h3>
</fieldset></div>
</div>
</body>
</html>
   at System.Data.Services.Client.QueryResult.Execute()
   at System.Data.Services.Client.DataServiceRequest.Execute[TElement](DataServiceContext context, QueryComponents queryComponents)
any ideas? Thank you very much!

Hi,
I am unable to connect to
http://hostname:81/Orchestrator2012/Orchestrator.svc/ in IE and am getting the same error while creating the connector.
I can connect to orchestrator via http://hostname:81/ but it still gives me the same error when I create the connector (Cannot connect Service Manager with Orchestrator Web Service).
anyone seen it before?

SPA3102 when NAT is off I cannot connect to graphic interface

Similar Messages

Maybe you are looking for