Spam wrongly installed

Hi,
i installed SAP NETWEAVER 7.0 enhancement package 2. after installation i upgraded kernel to the latest availabe version, and also the spam. for spam the default version it came along with installation is SAPKD70237. Now i am trying to update it to the latest, i downloaded & i applied SAPKD70044. after lot of time SPAM version SAPKD70044 was installed. Now i realized that i did a mistake and want to apply SAPKD70243.
when i try to update spam the below error is coming
SPAM/SAINT update SAPKD70243 has a lower version (0043) than SPAM (0044)
Please help
Sarat

Hi Sarat,
If your spam version is displayed as 7.02/44 then you must have applied SAPKD70244 and not SAPKD70044 - because it would not allow you to install the incompatible version. The error mentioned in your first post suggests the same.
Could you please re-verify the same ?
Try updating the SPAM version to SAPKD70245 once its available.
Are you getting any issue while defining a SP queue?
Regards,
Varun

Similar Messages

Put wrong install disk in mac mini

I was trying to recover iMovie on my dad's Mac mini and put the wrong install disk into the drive without realizing it until later. It prompted me to restart and when I did, the white screen showed up and just stayed there. What do I do? It's completely stuck!

Restart again with the mouse button or eject key pressed.
(68545)

Patches installed since May 31 have wrong install date - always Dec 2005

Using updatemanager to display installed patch information I discovered that for many of the installed patches the latest version claims to have been installed last December while previous versions were installed at various times this year.
For example:
119082-15 installed 2006/05/13
119082-16 installed 2006/05/28
119082-20 installed 2005/12/24
But according to the patch log rev 20 was installed on July 24 2006.
Going through the patch logs any patch installed since May 31, ie in June, July, shows an installation date of 2005/12/x where x is the correct day of the month
Where does updatemanager get this information from?

Thanks to the support folk we have determined what is happening though not the exact reason why things started going wrong.
It seems that some patch/patches applied in June, possibly related to locale or at least affected by locale, changed the way pkg information was stored in the pkginfo database - specifically the installation date used full month names instead of three letter abbreviations.
[updated to correct the above. Actually it seems the full month has always been used. It was just that May, being only three letters long worked correctly regardless, so I only noticed the problem for June.]
Updatemanager uses the /usr/lib/patch/list_patches script to generate the patch information that it uses to generate its own display. That script assumes three letter month names and if it doesn't find it then a month of 00 is specified. Consequently the installation date for a patch becomes 200600nn where nn is the day. By chance/coincidence/design the zeroth month of 2006 is treated as the month before the first month of 2006, which is December 2005. As a result all the patches which generated a 200600nn date get displayed as nn Dec 2005.
As I said it isn't clear what patch (or combination of patches) resulted in the changed date format. There is a CR 6285720 that is somewhat related in getting the list_patches script updated to handle different date formats. Meanwhile you can edit the script directly to use:
case "$MONTH_ENG" in
Jan|January ) MONTH=01;;
Feb|February ) MONTH=02;;
Mar|March ) MONTH=03;;
Apr|April ) MONTH=04;;
May ) MONTH=05;;
Jun|June ) MONTH=06;;
Jul|July ) MONTH=07;;
Aug|August ) MONTH=08;;
Sep|September ) MONTH=09;;
Oct|October ) MONTH=10;;
Nov|November ) MONTH=11;;
Dec|December ) MONTH=12;;
* ) MONTH=00;;
esac
Message was edited by:
davidholmes

Host: Unable to load application configuration + wrong install version on download

i am using 64 bit windows 7 ... when unable to playing video, it redirects me to the adobe download pages to get flash player ... the page says i am about to download flashplayer for win7 64 bit, of 9MB approximately, but the file i get has name "install_flashplayer11x32_mssd_aih.exe" (NOTE THE NUMBER 32) and this file just wont install it ends with error message: HOST: Unable to load application configuration ...
By google i found also file install_flashplayer11x64_mssd_aih.exe (NOTE THE NUMBER 64) ... this file runs the install, i get the final screen saying "installation completed" but after clicking the "finish" button i get an error message saying "an error occured while sending a command to the program" ...
I am just getting mad ... its 3 days i am trying to figure aout this problem ...
i also tryed files as "install_flash_player_11_plugin.exe" , "install_flash_player_11_plugin.msi" , "install_flash_player_11_active_x.exe" and "install_flash_player_11_active_x.msi" ... those files actually proceeds with the install, but at the end, the videos are still not displaying ...
When i am checking the plugins statuses in my firefox addons manager, it says Shockwave Flash is all right ...
The precedent version of flash player was working just fine, i do not understand why you must make such a mess every 2 months ...
How do i get work this?

yes, the pages is http://get.adobe.com/flashplayer/
the page says:
Adobe Flash Player 11.3.300.257 (9.36 MB)
Your system: Windows 64-bit , English, Firefox
but when i click the "Download now" button i get the file named "install_flashplayer11x32_mssd_aih.exe" (NOTE THE NUMBER 32) which wont start and after few seconds i get the message "HOST: Unable to load application configuration"
but finaly i solved the problem ... i just installed the file found by google on some private page "install_flashplayer11x64_mssd_aih.exe" (NOTE THE NUMBER 64)
(the page is here: http://www.ziddu.com/download/16693235/install_flashplayer11x64_mssd_aih.exe.html)
and after that i disabled the protected mode of flashplayer by adding a line in the cfg file
the howto is here: http://forums.adobe.com/thread/1018071
i must say its quite shameful one must get this torture to have movies playing on websites ... this cant happen at open source stuf, at least not for 3 days ...
and being already here and complaining, i must say also (i hope some adobe emploee will read this) i am quite disgusted (and i believe not only me) by adobes bad habit to provide other software than flashplayer, when they include mcafee antivir into the install ...
it is literally taking the user as a stupid one ...
if i will need an antivir, i will look for it ...
i just hate when some society tries to infiltrete in my comp some crap software counting on possibility that at the download i will not pay enough attention
its just ridiculous and shameful behavior

Live Update showing wrong installed version of driver

Hi, I have the latest Intel ME driver (10.0.31.100) installed. But live app showing that I have the 10.0.0.124 version and suggesting to download the latest one. I'm just ignoring the warning but why is this not corrected since I have this problem at t...

Quote from: JLio01 on Today at 02:43:02Have you tried click on "Ask for support" and contact msi the reason being denied?
I know why it's being denied. What I have an issue with is MSI seemingly being the ...

Used the wrong install disk and now it wont eject the disk

Alright I know that I'm an idiot but I made a boo boo.
I have a G4 powerbook (newer one with the superdrive) that needed a new hard drive. I changed the harddrive no problem but heres my problem:
I went to install the OS and I have a new MacBook, and I accidently put the disk for the MacBook in the PowerBook and now the Powerbook wont give it back! It doesnt have the little spot to stick a paperclip in and it gives you the cd back.
Obviously the computer cannot boot from the MacBook disk and I've tried EVERYTHING to get the disk to come out. But since the disk is mounted and is what the utilities are running off of it wont eject it.
I would open up my powerbook again and try to pry out the disk but i dont want to run the computer or the disk.
Any suggestion?
Thanks in advance.

"I can try this my only concern is that the disk utility is running from the boot disk and i have a feeling it wont eject the disk if the utility is running off the disk."
You may have a point there. That's why I recommended the Firewire, Target Disk Mode. I know it works. At least, that's the way I've always gotten out stuck disks. And in my case, most of the time, it's been when I've reformatted a drive and it has no startup volume or OS to startup from.
So, if you have a disc in there, it will not spit it out. (Not saying that other's suggestions won't work to do so).
Starting up in Target Disk Mode bypasses that function, booting up, so while it's connected to another Mac, it doesn't need the disc nor will it access it while on.
You might be able to do your own suggestion. But the external CD-ROM drive will have to be connected via FireWire in order for the Mac to recognize your installation disc as a startup volume. (Also, make sure installation disc is not a DVD as opposed to a CD... most installation discs in the latter G4 era were DVDs, if I'm correct-- especially Tiger).
In that case, when you startup, hold down the OPTION key so that you can choose which install disc to startup/boot from. Just make sure you choose the one that's in your external optical drive.
P.S. Did you HOLD DOWN the mouse button when starting up? You can't just click on it. Once you turn the Mac on, hold down the mouse button until the disc comes out, and don't let go.

PLZ HELP Having problems with a wrong installed msi utility program.

Hi,
My name is Nick
when I tryed to install a new update of msi fast boot, an error occured, now msi fast boot isnt installed correctly and i cannot find it anywhere to uninstall or to install again.
I used live update to install the new update.
These are my computer specs :
Operating System: Windows 8.1 64bit
Motherboard model: Z87 MPOWER (MS-7818)
Motherboard Bios version: 1.8
Graphic card mode: NVIDIA Geforce GTX 780
Graphic card Bios Version : NV296MS.131
Processor : Intel core i7 4770K @3.5ghz
Memmory: 16GB RAM
System Drive: Samsung EVO 250GB SSD

Uninstall the fastboot utility via Windows software menu. Afterwards install latest version: http://download.msi.com/uti_exe/FastBoot_mb.zip

Wrong install directives. 9i linux/390

On
http://www.oracle.com/technology/software/products/oracle9i/htdocs/390soft.html
this is wrong:
- Extract the file resulting from the step above using "cpio". Eg.: "cpio -idcmv < lnx390_db_9201_Disk1.cpio".
this is right, please correct:
- Extract the file resulting from the step above using "cpio". Eg.: "cpio -idmv < lnx390_db_9201_Disk1.cpio".

Hi,
Is the libclntsh.so.9.0 in $ORACLE_HOME/lib directory? If not, you should try to relink the Oracle installation.
$ ls $ORACLE_HOME/lib/libcln*
No such a file or directory
$ relink
parameters: all, oracle, network, client, client_sharedlib interMedia,
precomp, utilities, oemagent, ldap
$ relink all
(I have never even seen Linux on OS390 so I have no idea if it works the same way it works on Intel...)
Regs,
Mikko

Wrong instal?

i'm trying to instal the new flash player, but when i instal it said "version 7,0,14,0 was instaled" what the hell is happening?!? i tryed instaling it like at least five times and thats what it said every time, when i check the version on the site it sais i got 10,0,42,34 (i'm pretty sure that's the new one) but it won't work with youtube or the apps on facebook. can anyone help?
thx
afro

afroblademaster wrote:
vista home premium
32-bit or 64-bit?
What do you see at http://www.adobe.com/software/flash/about/ - does it give you a version information?

Re: Live Update showing wrong installed version of driver

try with other version off live update, i got that problem too

Hi
As for Intel ME, ask MSi techs as they should tell whats the issue (database might not be updated?): >>How to contact MSI.<<
As for Killer, correct: just driver is much smaler than driver+...

Premiere elements 11 failed to install with the error about shared technologies

PRE 11 failed to install with the error "The installation process has encountered an error while installing shared technologies. Please restart your system and try again" all that does is uninstall everything and I have to restart agin with the same error and we go on. So far the only way it is working is at the point of the "error message" I run task manager and stop the installer, I know it's leaving files that should be removed by the installer, but it worked. This information was gained on one of the forums and seems to work. Yesterday was the first time I really used it fully and although I was able to create a project I cannot output it as a file (mpg), it starts to output ok then throws up an error and fails. As PRE 10 was still installed I imported the project (which amazed me) into PRE 10 and outputted as required with no error. All this may be due to something being wrongly installed or not being installed in PRE 11, I don't know. Can anybody help
Dennis
using Windows 8 Pro
PS I downloaded the Adobe Support adviser and No errors

See the following help document:
http://helpx.adobe.com/photoshop-elements/kb/troubleshoot-installation-photoshop-elements- premiere.html

Imac G5 not reconizing Leopard install, Need help diagnosing.

Hello, my names Jarid and my problem is the following;
*_Using Now_*
I am currently on my macbook pro 10.6.5 snow leopard OS.
Background
I got an Imac for Christmas from my fathers Friend, the friend recently moved to china and left it behind.
this G5 (2 gigs of ram, 1.8 ghz processor) had tiger installed on it but while i have switched to mac about 6 months ago, I have a strong background in windows and learning as i go on mac. I wanted to install leopard on this G5 because my Macbook was leopard when i received it so i wanted to upgrade for familiarity.
One strange thing right before i tried to install was i tried to install new applications and they would just open up really quick on the dock then disappear and not work. Firefox worked, as well as itunes ect but they were already installed..(I think i may have DL the wrong OS support?? i do not know)
While installing a new program it actually started to run; i tried to DL a tiger version of an app to see if i might have been using the wrong instal(this is where i thought i was installing the wrong OS app maybe?).
The comp sort of froze, so i restarted holding down the power and got the purple folder with the blinking '?'. I figured i could just install leopard and fix what appeared to be "corrupt system/32 boot"(windows) I Bought Leopard @ best buy 10.5 and put the disk in and pressed "c".
Problem
It started fine until i had to pick a disc to choose from, there was no drive. I opened disk utility and I THINK it had 1 partition listed and the disk drive. I then proceeded to "erase" the drive considering it was already missing files anyways. I remember something though like I created "journalism" or something and the drive now showed in the "where do you want to install". I chose the only drive (hard drive 250g). I watched it for 40 minutes and then went and UG my leopard to snow leopard. When I finished, I figured my G5 would be done however the screen did not light when I used the mouse or keyboard. I shut it off by holding the power button. now I still get the purple folder with the '?' mark. When i use the disc to boot I cant see the drive again but this time all that is in the disk utility is a pic of a cd (guessing my boot disc) even though i saw the HD there 2 hours ago...
*_Things I Have Tried_*
1. I tried using terminal in the start up with the disc to find the drive, but it listed disc 0 1 2 3 with like 500 mb, I think 2 "X" amount of kb, lastly like one 7 GB and that was it no big HD listed?
2. I tried Holding "option" and try finding the drive but nothing showed up, I took the installation disc out at this point.
_*+Additional info+*_
I know Windows Xp extremely well but not mac too much and **everything I've done was done from what I've been reading offline**. Any help would be greatly appreciated. +I am still new to mac+ so if it is not windows-type ideology please explain A little more in depth for me please, thank you.

You might try resetting the SMU:
1. Shut down the computer.
2. Unplug the computer's power cord.
3. Press and hold the power button for 5 seconds.
4. Release the power button.
5. Attach the computers power cable.
6. Press the power button to turn on the computer.
Or reseting the PRAM.
You can check the drive using Apple Hardware Test, which should be on one of your install discs, hold down the D when booting to it.
Did you wipe the drive when you were running from the install disc?
If the install disc works, try using Disk Utility to repair your drive, but it sounds as if the hard drive has failed.
1. Insert the Mac OS X Install disc that came with your computer, then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu. (In Mac OS X 10.4 or later, you must select your language first.)
Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.
3. Click the First Aid tab.
4. Click the disclosure triangle to the left of the hard drive icon to display the names of your hard disk volumes and partitions.
5. Select your Mac OS X volume.
6. Click Repair. Disk Utility checks and repairs the disk.
Let us know how you make out,

I can't install either leopard or tiger on my iMac G4

I just bought a used iMac g4 with the following specs: 1.25 ghz, 160 gb HD, 1 gb of ram, with a 20" screen (USB 2.0). It has OS X 10.3.9 installed. I have retail copies of tiger and leopard. The problem is that I can't get either to install. When i load the disk, the computer restarts, but then returns back to home screen. I've tried holding down "c", but that does nothing for me. I've also gone to start up disk in utilities, but all that is listed on there is my G4 hard drive and "network". The superdrive isn't listed on there. I know the super drive works; i've used it several times and i used it to open up the install disk. What am I doing wrong. Any help or advice would be much appreciated.

Your symptoms are consistent with either the superdrive not working, or with you having the wrong install disks.
Can you put other CDs or DVDs into the drive, do they show up ok and work?
When you put the install disk in the drive, do they show up on the desktop?
Where did you get the install disks from? How do you know they are the universal install disks (e.g. can be used on any Mac) versus the machine-specific ones that come with a specific model and only work on those models? The fact that you cannot select the CD/DVD as a startup disk seems to indicate that it cannot start up your model, e.g. it can only start up a different model.

OBIEE 11g 64-bit install on Windows 64-bit

I wanted to solicit any experiences that the user forum is having with installing 11g on a 64-bit Windows platform. I understand that the Admintool/Job Manager will not run with the 64-bit installation package but we can install the newly released Client install to circumvent this. I am seeing many forums out there in which the 64-bit OBIEE install is done as Simple or Enterprise. My understanding is that this is useless as the bundled WebLogic utilizes at 32-bit JVM. There is a Doc ID out on Metalink (ID 1220564.1) that states one can only do a Software Install. So we have proceeded with the following steps of downloading first the Java 64-bit JVM, then a WebLogic instance utilizing the 64-bit JVM (java -D64 -jar xxx.jar) and finally the OBIEE Software Only install.
The issue we are running into is that the Install fails when attempting to start the OPMN. So during the install the "Executing:opmnctl start coreapplication_obips1
" fails and references the OPMN not starting. We are unable to start the OPMN service as well. We have a static IP, so this not the known issue with the loopback adapter. The other issue I saw was having to install the VC++ 2005 SP1 libraries per another Metalink Doc ID (1226254.1). This was all done, however, the install continues to fail.
It seems the lack of knowledge from support as well as the vague/lack of documentation is frustrating. I just wanted to ping the OTN community around this scenario.

Thanks Paul, really appreciate the update. Spent this morning rebuilding our environment with 64-bit (Win 2008) and starting from scratch. The install has now succeeded. I tell you one thing you pointed out is something we noticed when we proceeded with the second install. That was the WebLogic version. I had initially used .4 and on the second install we used .3. I am guessing that this may have been the issue.
I will verify with our Oracle resources and I hope this post will assist other when doing the 64-bit install as I think it is very vague in the documentation.
I will update the post with Oracles response as well.
Just as an FYI... the reason this issue came up in the first place was we did an Enteprise Install on 64-bit and found that the Gauge Charts weren't working in the SampleAppLite Subject Area. So I will add that to the Tags for this post.
Hope this post helps others and they don't go through the headaches of a wrong install type.

Error when trying to start from install disk OS X 10.4

Hi,
I have an iBook G4 with the 1.42 GHz model, 60 GB, 512 RAM. I am running OSX 10.4.11. I would like to get it to run better. I installed TenFourFox as my new browser, that seemed to help, but it's still pretty slow. So then I freed up some more space on the hard drive. Then I started it up in Safe Mode, then I ran the disk utility and repaired the disk permissions. I ran the disk verify and found errors, and I then ran fsck - y at the command line. That seemed to get rid of the errors, but I am thinking I should format the hard drive and do a clean install.
Will doing a clean install help the computer run better/ faster? How can I do it? I am running into errors...
I lost the install disks, but luckily a friend of mine had a copy.
I insert the disk, power down, and restart.
I get the a really long error message, below are snippets:
panic(cpu 0 caller 0x002E0BF4): Unable to find driver for this platform: "PowerBook6,7"
Latest stack backtrace for cpu 0:
Backtrace 0x00099EA4 0x0009A860 0x00027A28 0x002E)B4.....
No debugger configured - dumping debug information...
panic: We are hanging here.
Is there something wrong with my computer? Or are the install disks not compatible? Maybe they were install disks for a powerbook and not an iBook (not sure if that matters).
I am also considering installing RAM. Will that help a lot with the speed (i.e. 50% faster?) or just a little?
Thanks a lot for any input!

Wrong install Disc, that one is machine specific, & doubtful a reinstall will help all that much.
More RAM will likely help, but not awfully likely it'll be 50%.
To tell, ehen it gets slow, Open Activity Monitor, Show:>All Processes, sort on CPU%, see if anything using too much CPU% when this happens, click on Memory tab, do you have many Pageouts?

Spam wrongly installed

Similar Messages

Maybe you are looking for