SPARCengine CP1500 & Solaris 2.5.1.?

Hi, All!
Help, please!
I am beginning unix administrator..
I have SPARCengine Ultra CP1500.
Can I install Solaris 2.5.1 on my machine?
If YES, then is there any specific problem for installing Solaris 2.5.1.?
Thanks & Regards,
Lyudmila

When the keyboard is disconnected...display automatically goes to the serial port. If your keyboard is connected, reboot and make sure you have a video card installed. The onboard one may not have the vsimm(video memory) option, in which case you will have to get memory for it(very, very expensive) or get a separate sbus video card(these can be had very cheap on ebay). Let us know how it works out for you.

Similar Messages

NETRA 7 segment display H E L P, any ideas???

when turn on the Netra t1 105 inside diplay (7 segment leds) display a sequence H, E, L, P but i no have a idea why happen this, any idea???
thanks
sorry my bad english

The Netra t1 105 documentation only describes the LEDs visable on the outside of the case.
The Netra t1 105 conains a SPARCengine CP1500 board, for which detailed documention is available at:
http://www.sun.com/oem/products/manuals/
From http://www.sun.com/oem/products/manuals/806-2104-03.pdf
<table border="0" align="center" width="90%" cellpadding="3" cellspacing="1"><tr><td class="SmallText">Quote:</td></tr><tr><td class="quote">
The characters in the LED displayed by OBP indicate the following:
O (The letter O ) OBP is currently executing.
E RED state exception encountered in OBP.
b Solaris boot has taken place.
H, E, L, and P This sequence (with each letter flashed at a 4-second interval) is initiated if the system is at the ok prompt for more than two minutes after power-on, without booting. It does not appear after Solaris has booted.
</td></tr></table>

Boot load failed, fatal SCSI error, disk read error, Elf64 read error

Just came from vacation and started the Unix Solaris system from work.
Unfortunately I get these errors that you can see in the image:
Can someone tell me what is the problem? Until now I didn't had this issue before.
Thanks!

Moderator Action:
This thread has been moved from the Solaris Kernel discussion space,
to the Sun Servers HARDWARE discussion space, for closer topic alignment.
I concur with Pascal that you do not have a Solaris kernel issue, nor even a Solaris issue.
You have an ancient AXI systemboard (which was a piece of hardware manufactured by Sun Microsystems for the OEM market -- most likely the SPARCengine CP1500 board). It is UltraSPARC-IIi hardware that is about 15 to 20 years old, and it is tired.
I suggest you shut the box down, completely take it apart and then put it back together again.
Remove all accumulated dust and lint.
Remove and reinstall the CPU modules. Remove and reinstall the RAM. Remove and reinstall all expansion board risers. Remove and reinstall all adapter cards. Examine all internal data cabling. Clean any and all cooling fans as well as the power supply.
That action will burnish all mechanical and electrical connections.
After you have re-assembled the box, boot from CDROM and examine all your filesystems. FSCK any that require it.

"Elf64 read error"

Anyone know what this is and what I can do about it?
"Elf64 read error"
Comes up when I boot the machine.

Moderator Action:
This thread has been moved from the Solaris Kernel discussion space,
to the Sun Servers HARDWARE discussion space, for closer topic alignment.
I concur with Pascal that you do not have a Solaris kernel issue, nor even a Solaris issue.
You have an ancient AXI systemboard (which was a piece of hardware manufactured by Sun Microsystems for the OEM market -- most likely the SPARCengine CP1500 board). It is UltraSPARC-IIi hardware that is about 15 to 20 years old, and it is tired.
I suggest you shut the box down, completely take it apart and then put it back together again.
Remove all accumulated dust and lint.
Remove and reinstall the CPU modules. Remove and reinstall the RAM. Remove and reinstall all expansion board risers. Remove and reinstall all adapter cards. Examine all internal data cabling. Clean any and all cooling fans as well as the power supply.
That action will burnish all mechanical and electrical connections.
After you have re-assembled the box, boot from CDROM and examine all your filesystems. FSCK any that require it.

SUNFIRE V210, E1F64 read error boot failed?

Does anyone know what this error means on the Sunfire v210 server?

Moderator Action:
This thread has been moved from the Solaris Kernel discussion space,
to the Sun Servers HARDWARE discussion space, for closer topic alignment.
I concur with Pascal that you do not have a Solaris kernel issue, nor even a Solaris issue.
You have an ancient AXI systemboard (which was a piece of hardware manufactured by Sun Microsystems for the OEM market -- most likely the SPARCengine CP1500 board). It is UltraSPARC-IIi hardware that is about 15 to 20 years old, and it is tired.
I suggest you shut the box down, completely take it apart and then put it back together again.
Remove all accumulated dust and lint.
Remove and reinstall the CPU modules. Remove and reinstall the RAM. Remove and reinstall all expansion board risers. Remove and reinstall all adapter cards. Examine all internal data cabling. Clean any and all cooling fans as well as the power supply.
That action will burnish all mechanical and electrical connections.
After you have re-assembled the box, boot from CDROM and examine all your filesystems. FSCK any that require it.

Problem installing Solaris 10 onto CP1500

I'm trying to install Solaris 10 11/06 onto a CP1500 (UlraSparc-IIi, 440MHZ, 1GB RAM, OpenBoot 3.10.24, using a PS/2 Keyboard). The install CD boots up, but soon after the initial boot (after it displays copyright information but before the installer starts) it goes into a state where it syncs the file system, then reboots. If set to boot from the CD-ROM, it just goes through this process in an continuous loop: boot, cut to file system sync, reboot, cut to file system sync, reboot, wash, rinse, repeat to infinity. The acutal file system sync happens in the blink of an eye. I don't believe that this has anything to do with the state of the hard disk, as it does this even when the hard disk is disconnected from the SCSI bus.
I'm installing from an IDE CD-ROM drive that is connected to the SCSI bus using an adapter. I've sucessfully installed Solaris 8 onto this system, but alas, I need Solaris 10.
Does anyone have any idea what might be causing this? Any help would be appreciated.
Thanks!

I downloaded the latest version of Solaris 10, and that solved the problem of the continual reboots. Now the keyboard doesn't work, but that's a different problem.

Cannot mount root during Solaris install on SPARCengine ULTRA axi

I use boot cdrom which sucessfully formats swp partition and copies files to hd. But then when I reboot I get the following:
SPARCengine(tm)Ultra(tm) AXi (UltraSPARC-IIi 440MHz), PS/2 Keyboard
OpenBoot 3.10.10 ME, 512 MB memory installed, Serial #10660686.
Ethernet address 8:0:20:a2:ab:4e, Host ID: 80a2ab4e.
ok boot disk4
Boot device: /pci@1f,0/pci@1/scsi@1/disk@4,0 File and args:
SunOS Release 5.8 Version Generic_108528-11 64-bit
Copyright 1983-2001 Sun Microsystems, Inc. All rights reserved.
Cannot mount root on /pci@1f,0/pci@1/scsi@1/disk@4,0:a fstype ufs
panic[cpu0]/thread=10408000: vfs_mountroot: cannot mount root
0000000010407970 genunix:vfs_mountroot+70 (10435c00, 0, 0, 10410920, 10, 14)
%l0-3: 0000000010435c00 00000000104391c8 000000002f000000 0000000010435dc0
%l4-7: 0000000000000000 00000000104136b8 00000000000b7bf6 0000000000001bf6
0000000010407a20 genunix:main+94 (10410168, 2000, 10407ec0, 10408030, fff2, 1004
ef88)
%l0-3: 0000000000000001 0000000000000001 0000000000000015 0000000000000ea5
%l4-7: 0000000010428c28 0000000010462320 00000000000cd920 0000000000000540
skipping system dump - no dump device configured
rebooting...
Resetting ...
PS: I have recently reset the NVRAM on this machine not sure if there are any env settings I should have setup in OBP (I reset HOST ID and MAC-ADDRESS).

disk@0,0:a is slice/partition 0
disk@0,0:b is slice/partition 1
I'm not sure where you told it your swap slice was going to be. Looks like slice 1. Mini-root gets installed in slice 1 and then the install begins from there.
In the future, if you just "boot cdrom" from disk 1 of 2 you won't run into these issues.

Solaris 8 wrong patches?

Hi,
there are 2 patches that don't install on my system :
118097-05 SunOS 5.8: bug fixes for cdrw 1.1
115951-03 Netra ct OBP update for SUNW,UltraSPARC-IIi-Netract
For sure it's because the concerning packages are not installed. But why am I offered these patches? On another Solaris 8 machine with the same patch settings the patches are not installed and also not downloaded or named in smpatch analyze output.
What's wrong?
system information:
SunOS 5.8 Generic_117350-53 sun4u sparc SUNW,Sun-Blade-1000
# smpatch get
patchpro.backout.directory - ""
patchpro.baseline.directory - /var/sadm/spool
patchpro.download.directory - /var/sadm/spool
patchpro.install.types rebootimmediate:reconfigimmediate:rebootafter:reconfigafter:standard:interactive rebootafter:reconfigafter:standard
patchpro.patch.source https://getupdates1.sun.com/ https://getupdates1.sun.com/
patchpro.patchset current current
patchpro.proxy.host "" ""
patchpro.proxy.passwd **** ****
patchpro.proxy.port "" 8080
patchpro.proxy.user "" ""

What are the errors when you try to install the patches? 115951-03 has been validated.
Installing patches from /var/sadm/spool...
Failed to install patch 115951-03.
Utility used to install the update failed with exit code 7.
The packages in /var/sadm/spool/115951-03.jar.dir/115951-03are not proper patch packages.See instructions for applying the patch in patchadd(1M).Patchadd is terminating.
grep: can't open */pkginfo
Failed to install patch 115951-03.
ALERT: Failed to install patch 115951-03.
118097-05 has been validated.
Installing patches from /var/sadm/spool...
Failed to install patch 118097-05.
Utility used to install the update failed with exit code 8.
Checking installed patches...One or more patch packages included in118097-05 are not installed on this system.Patchadd is terminating.
Failed to install patch 118097-05.
ALERT: Failed to install patch 118097-05.
How are you trying to install the patches?Tried it with
smpatch update
smpatch update -i patch-id
smpatch download -i patch-id and smpatch add -i patch-id
Everytime the same error.
What are the contents of /var/sadm/patch/<patch-id>/log for each patch?The patches are not installed so there are no such directories.
What is the output of:
# pkginfo -l SUNWcdrw CP1500PKGINST: SUNWcdrw
NAME: utility for writing to DVD-RW and CD-R/RW disks
CATEGORY: system
ARCH: sparc
VERSION: 1.0,REV=2000.07.12.10.09
BASEDIR: /
VENDOR: Sun Microsystems, Inc.
DESC: utility for writing to DVD-RW and CD-R/RW disks
PSTAMP: on28-dhpg20070531094326
INSTDATE: Feb 19 2008 04:17
HOTLINE: Please contact your local service provider
STATUS: completely installed
FILES: 7 installed pathnames
5 shared pathnames
5 directories
1 executables
1 setuid/setgid executables
265 blocks used (approx)
ERROR: information for "CP1500" was not found

CP1500 CPCI Motherboard Requires COM connection

I am using a CP1500 - 440MHz motherboard in a CPCI system. For the system to start it always requires a COM cable connection to a PC running a Serial Terminal Emulation program. When the system is booted up, if the COM connection is removed by either removing the cable or exiting the Serial Terminal Emulation program the CP1500 system crashes. The system will not boot up without the COM cable connected with the Serial Terminal Emulation program running. Another system I have does not need the COM cable connection running to start up. It is not the hardware at fault. Does any one know if there is a file within Solaris 2.6 or 8 that states that the COM cable must be connected to a Serial Terminal Emulation program for the system to run?
Thanks
Ryan

Normally no terminal is required for a system to boot unless "auto-boot? false". This would require you to have to type "boot" at the ok prompt. Thus you would be required to have some type of input device to type. At the ok prompt type printenv auto-boot? If it comes back false then you should type setenv auto-boot? true to change it. Then type reset to lock it in to NVRAM. You may also want to investigate the kbd -a enable / disable command while you are unpluging your laptop. Some have found that killing Hyperterm while still plugged in causes a break to be sent and the system goes to the ok prompt. They pull the cable first and they kill it. Your results may vary. The kbd -a command allows you enable or disable the abort (break, Stop +a) to the system while you are connecting or disconnecting cables to the serial port. You may want to experiment with this as well.

Unable to load Solaris 8 using Panasonic CD drive

I am not able to load solaris 8, Sparc version 6/00 into a Sun UltraSparc AXe system using the Panasonic CR-176D CD-ROM drive. Also tried with TEAC CD-224E CD drive with similar problem.
The system indicate a timeout error, abort and reset the system.
Has anyone encountered this? Is it a hardware compatibility issue or a software bug? Any device driver or patches to fix thie issue ?
Any advice will be helpful.
Thanks.

Hi, 
I couldn't find any know bugs with these particular models 
but neither of them appear on the compatibility list. 
Have a look at the following URL for a list of third party 
products compatible with the SPARCengine Ultra AXe board: 
http://www.sun.com/microelectronics/ihv/AXe_ihvprod.html 
 
Hope this helps. 
 
Caryl Takvorian 
Sun Developer Technical Support

Where do I find SPARCengine AXi Update and Release Notes?

I'm looking for the OBP updates, and all release notes for the updates, so that I can flash the two I have recently obtained and add the intervening release notes to the manual I printed out for the boards.
Also, I'm looking for the OBP dropins compatible with the SPARCengine AXi.
I've tried SunSolve, but haven't really turned up anything close.

Well, I was playing around with FreeBSD initially on the 4 gig disk that did work, but there are a lot of things in the FBSD ports tree that need work to get going on the SPARC. I love FBSD, and run it on intel boxes, but work is needed on it.
I may devote one of the 18 giggers (when I get another SCSI cable, or an external case) to FBSD to do some porting work for the project...
Anyhow, I have successfully installed Solaris-SPARC-u1 on it, and the only problems I saw were in the freeware, where stuff like emacs would coredump on exit (from the package), or fail to compile (segfault on the blessmail module).
I have just installed Solaris-SPARC-u2 (6/06) on it today, and so far have no issues, but I do want to test the issue with emacs again.. I'll be pissed if emacs has issues on this, vi sucks (EMACS makes the sun shine! EMACS makes the birds sing! EMACS makes the grass grow green! It's a pretty good editor too!).
By "RTC" I mean the RealTime Clock / CMOS battery-backed NVRAM / IDPROM chip. Refer to the OEM Technical manual for the AXi for details on where it is on the board. They are field replacable and socketed.
The RTC in the AXi board is a SGS (ST) M48T59Y, and you can find the datasheet at: http://www.st.com/stonline/products/literature/ds/7001.pdf and you can find out how to replace it, and reprogram your hostid and MAC, etc at: http://www.squirrel.com/squirrel/sun-nvram-hostid.faq.html the chip is avaqilable from Mouser Electronics, probably Digi-Key as well, among others. Keep in mind they have an embedded lithium cell, and have a lifespan between 7 and 10 years.
As far as fans, I have 300 MHz CPUs in these right now, until I can find the Sun fans and mounting brackets... In the meantime, the fans are connected to the main power supply directly. As far as LEDs, I don't see how that could cause a problem, as a reverse-biased diode simply won't pass current.
Anyhow, I have had some cheap fans fry intel motherboards when they die and freeze up, so, I think I'll even direct-connect the CPU fan to the power supply when I get some of the 440's...
As for Solaris 10, I don't have any problems other than the one issue, but I do have one issue launching from a remote Xnest on my PC, but, for some reason, it works fine when I use the kdm remote login from the main kdm login screen on my pc. For some reason Xnest will do the dtlogin stuff fine, but it will never launch CDE and immediately go back to the dtlogin screen. The answer might be in the Xservers file in the /usr/dt/config directory, but it uses some wierd bastardized form that isn't standard Xservers, and will coredump dtlogin if it isn't in the form expected. I think the key is in finding out what the hell "Class" a foreign Xnest is.
Anyhow, I'm having fun, and only have one more complaint.. I can't set the font size on anything other thant he output and editor windows in Sun Studio 11 (which I also installed today). IMHO, the fonts are a bit small.

Logical interface in solaris 10

Hi there,
I need to configure logical interface in a solaris 10 3/05 server. After reading the Solaris 10 IP services manual, I am not quite sure what to do. All the examples and explanation are about using the new subcommand addif of ifconfig. It was not clear in the documentation if the setting logical interfaces via addif will persist across boot.
Can one still configure logical interface in Solaris 10 in a more traditional way like in Solaris 8? In an Solaris 8 server I will do the following.
Let's assume I want to configure in a solaris 8 server a logical interface named hme0:1 with IP address 192.168.20.28 with netmask 255.255.255.0 for hostname host001
# cat /etc/hostname.hme0:1
host001
^D
# echo "192.168.20.28 host001" >> /etc/inet/hosts
# echo "192.168.20.0 255.255.255.0" >> /etc/inet/netmasks
# reboot -- -r
Can one still do that in solaris 10 3/05 server?

Hi there,
I need to configure logical interface in a solaris 10
3/05 server. After reading the Solaris 10 IP services
manual, I am not quite sure what to do. All the
examples and explanation are about using the new
subcommand addif of ifconfig. It was not clear in the
documentation if the setting logical interfaces via
addif will persist across boot.No. No 'ifconfig' command is persistent.
Can one still configure logical interface in Solaris
10 in a more traditional way like in Solaris 8? In an
Solaris 8 server I will do the following.
Let's assume I want to configure in a solaris 8
server a logical interface named hme0:1 with IP
address 192.168.20.28 with netmask 255.255.255.0 for
hostname host001
# cat /etc/hostname.hme0:1
host001
^D
# echo "192.168.20.28 host001" >> /etc/inet/hosts
# echo "192.168.20.0 255.255.255.0" >>
/etc/inet/netmasks
# reboot -- -r
Can one still do that in solaris 10 3/05 server?Absolutely.
You don't need to reboot (you can run ifconfig for this boot and let the files do the work next time) and the -r doesn't do anything with interfaces (expecially virtual interfaces) anyway.
Darren

Installation problem on Solaris

I am trying to install sun one 7.0 on Solaris 8. The install is failing with this error:
ERROR - library load failed with following error: Can't load library: /opt/SUNWappserver7/lib/libinstallCore.so
INFO - End core server uninstallation
anyone know what causes this??
cheers

Looks like Solaris package installation failed and installer reverted to uninstallation sequence. For low level pkgadd log please check /var/sadm/install/logs/Sun_ONE_Application_Server_install.B<timestamp> file (timestamp is date and time of your installation attempt in mmddHHMM format).
Look for any errors in this file. Most likely thing that could have happened is that the installation of Java Help (SUNWjhrt) package failed because you didn't have existing package based J2SE installation on the system. If that's the case, workaround is to either preinstall package based J2SE installation or to selected option to install bundled J2SE that comes with application server.

Installation problem on Solaris 10

Dear All,
We are trying to install j2sdk 1.4.2_13 on solaris server zone. I have downloaded j2sdk-1_4_2_13-nb-5_0-solsparc-ml.bin
But when I try to execute this:
#./j2sdk-1_4_2_13-nb-5_0-solsparc-ml.bin
It gives me error: The installer is unable to run in graphical mode. Try running the installer with the -console or -silent flag
Tried with -console:
The wizard cannot continue because of the following error: Invalid command line option: console is not supported (10
01) (403)
WARNING: could not delete temporary file /tmp/ismp001/2599368
WARNING: could not delete temporary file /tmp/ismp001/6183226
WARNING: could not delete temporary file /tmp/ismp001/1222839
Then tried with -silent:
This time command just completed w/o any output at all.
Please suggest what can I do?
regards, Sean.

Dear Siddhesh,
Thanks for your reply.
I tried using X Manager GUI for my Solaris. But when I double click the j2sdk-1_4_2_13-nb-5_0-solsparc-ml.bin file to run it, it simply denies saying:
The filename "j2sdk-1_4_2_13-nb-5_0-solsparc-ml.bin" indicates that this file is of type "Unknown type". The contents of the file indicate that the file is of type "Shell script". If you open this file, the file might present a security risk to your system.
Do not open the file unless you created the file yourself, or received the file from a trusted source. To open the file, rename the file to the correct extension for "Shell script", then open the file normally. Alternatively, use the Open With menu to choose a specific application for the file.
Also /tmp has full authorizations:
drwxrwxrwt 7 root sys 557 Jun 24 08:34 tmp
I dont have Hummingbird for X11 forwarding with this client. Do I have any other option??
regards, Sean.

New to Solaris, Some Samba and NTFS issues.

Hi Im new to solaris and trying out ZFS which has been great.
Im haivng some trouble that I cant find up to date info on so here goes:
First how do you mount an NTFS volume in Solaris 11 Express?
I need to access the data on an NTFS drive to populate my new ZFS tank.
Secondly, I have read only access on my samba shares from windows machines but my smb.conf looks right. a copy of my smb.conf will follow
Any suggestions would be appreciated.
# This is the main Samba configuration file. You should read the
# smb.conf(5) manual page in order to understand the options listed
# here. Samba has a huge number of configurable options (perhaps too
# many!) most of which are not shown in this example
# For a step to step guide on installing, configuring and using samba,
# read the Samba-HOWTO-Collection. This may be obtained from:
# http://www.samba.org/samba/docs/Samba-HOWTO-Collection.pdf
# Many working examples of smb.conf files can be found in the
# Samba-Guide which is generated daily and can be downloaded from:
# http://www.samba.org/samba/docs/Samba-Guide.pdf
# Any line which starts with a ; (semi-colon) or a # (hash)
# is a comment and is ignored. In this example we will use a #
# for commentry and a ; for parts of the config file that you
# may wish to enable
# NOTE: Whenever you modify this file you should run the command "testparm"
# to check that you have not made any basic syntactic errors.
#======================= Global Settings =====================================
[global]
# workgroup = NT-Domain-Name or Workgroup-Name, eg: MIDEARTH
workgroup = WORKGROUP
# server string is the equivalent of the NT Description field
server string = Samba Server
# Security mode. Defines in which mode Samba will operate. Possible
# values are share, user, server, domain and ads. Most people will want
# user level security. See the Samba-HOWTO-Collection for details.
security = share
# This option is important for security. It allows you to restrict
# connections to machines which are on your local network. The
# following example restricts access to two C class networks and
# the "loopback" interface. For more examples of the syntax see
# the smb.conf man page
; hosts allow = 192.168.1. 192.168.2. 127.
# If you want to automatically load your printer list rather
# than setting them up individually then you'll need this
load printers = yes
# you may wish to override the location of the printcap file
; printcap name = /etc/printcap
# on SystemV system setting printcap name to lpstat should allow
# you to automatically obtain a printer list from the SystemV spool
# system
; printcap name = lpstat
# It should not be necessary to specify the print system type unless
# it is non-standard. Currently supported print systems include:
# bsd, cups, sysv, plp, lprng, aix, hpux, qnx
; printing = cups
# Uncomment this if you want a guest account, you must add this to /etc/passwd
# otherwise the user "nobody" is used
; guest account = pcguest
# this tells Samba to use a separate log file for each machine
# that connects
log file = /var/samba/log/log.%m
# Put a capping on the size of the log files (in Kb).
max log size = 50
# Use password server option only with security = server
# The argument list may include:
# password server = My_PDC_Name [My_BDC_Name] [My_Next_BDC_Name]
# or to auto-locate the domain controller/s
# password server = *
; password server = <NT-Server-Name>
# Use the realm option only with security = ads
# Specifies the Active Directory realm the host is part of
; realm = MY_REALM
# Backend to store user information in. New installations should
# use either tdbsam or ldapsam. smbpasswd is available for backwards
# compatibility. tdbsam requires no further configuration.
passdb backend = smbpasswd
# Using the following line enables you to customise your configuration
# on a per machine basis. The %m gets replaced with the netbios name
# of the machine that is connecting.
# Note: Consider carefully the location in the configuration file of
# this line. The included file is read at that point.
; include = /usr/sfw/lib/smb.conf.%m
# Configure Samba to use multiple interfaces
# If you have multiple network interfaces then you must list them
# here. See the man page for details.
; interfaces = 192.168.12.2/24 192.168.13.2/24
# Browser Control Options:
# set local master to no if you don't want Samba to become a master
# browser on your network. Otherwise the normal election rules apply
; local master = no
# OS Level determines the precedence of this server in master browser
# elections. The default value should be reasonable
; os level = 33
# Domain Master specifies Samba to be the Domain Master Browser. This
# allows Samba to collate browse lists between subnets. Don't use this
# if you already have a Windows NT domain controller doing this job
; domain master = yes
# Preferred Master causes Samba to force a local browser election on startup
# and gives it a slightly higher chance of winning the election
; preferred master = yes
# Enable this if you want Samba to be a domain logon server for
# Windows95 workstations.
; domain logons = yes
# if you enable domain logons then you may want a per-machine or
# per user logon script
# run a specific logon batch file per workstation (machine)
; logon script = %m.bat
# run a specific logon batch file per username
; logon script = %U.bat
# Where to store roving profiles (only for Win95 and WinNT)
# %L substitutes for this servers netbios name, %U is username
# You must uncomment the [Profiles] share below
; logon path = \\%L\Profiles\%U
# Windows Internet Name Serving Support Section:
# WINS Support - Tells the NMBD component of Samba to enable it's WINS Server
; wins support = yes
# WINS Server - Tells the NMBD components of Samba to be a WINS Client
# Note: Samba can be either a WINS Server, or a WINS Client, but NOT both
; wins server = w.x.y.z
# WINS Proxy - Tells Samba to answer name resolution queries on
# behalf of a non WINS capable client, for this to work there must be
# at least one WINS Server on the network. The default is NO.
; wins proxy = yes
# DNS Proxy - tells Samba whether or not to try to resolve NetBIOS names
# via DNS nslookups. The default is NO.
dns proxy = no
# These scripts are used on a domain controller or stand-alone
# machine to add or delete corresponding unix accounts
; add user script = /usr/sbin/useradd %u
; add group script = /usr/sbin/groupadd %g
; add machine script = /usr/sbin/adduser -n -g machines -c Machine -d /dev/null -s /bin/false %u
; delete user script = /usr/sbin/userdel %u
; delete user from group script = /usr/sbin/deluser %u %g
; delete group script = /usr/sbin/groupdel %g
#============================ Share Definitions ==============================
[homes]
comment = Home Directories
browseable = no
writable = yes
# Un-comment the following and create the netlogon directory for Domain Logons
; [netlogon]
; comment = Network Logon Service
; path = /usr/sfw/lib/netlogon
; guest ok = yes
; writable = no
; share modes = no
# Un-comment the following to provide a specific roving profile share
# the default is to use the user's home directory
;[Profiles]
; path = /usr/local/samba/profiles
; browseable = no
; guest ok = yes
# NOTE: If you have a BSD-style print system there is no need to
# specifically define each individual printer
[printers]
comment = All Printers
path = /var/spool/samba
browseable = no
# Set public = yes to allow user 'guest account' to print
guest ok = no
writable = no
printable = yes
# This one is useful for people to share files
;[tmp]
; comment = Temporary file space
; path = /tmp
; read only = no
; public = yes
# A publicly accessible directory, but read only, except for people in
# the "staff" group
;[public]
; comment = Public Stuff
; path = /home/samba
; public = yes
; writable = no
; printable = no
; write list = @staff
# Other examples.
# A private printer, usable only by fred. Spool data will be placed in fred's
# home directory. Note that fred must have write access to the spool directory,
# wherever it is.
;[fredsprn]
; comment = Fred's Printer
; valid users = fred
; path = /homes/fred
; printer = freds_printer
; public = no
; writable = no
; printable = yes
# A private directory, usable only by fred. Note that fred requires write
# access to the directory.
;[fredsdir]
; comment = Fred's Service
; path = /usr/somewhere/private
; valid users = fred
; public = no
; writable = yes
; printable = no
# a service which has a different directory for each machine that connects
# this allows you to tailor configurations to incoming machines. You could
# also use the %U option to tailor it by user name.
# The %m gets replaced with the machine name that is connecting.
;[pchome]
; comment = PC Directories
; path = /usr/pc/%m
; public = no
; writable = yes
# A publicly accessible directory, read/write to all users. Note that all files
# created in the directory by users will be owned by the default user, so
# any user with access can delete any other user's files. Obviously this
# directory must be writable by the default user. Another user could of course
# be specified, in which case all files would be owned by that user instead.
;[public]
; path = /usr/somewhere/else/public
; public = yes
; only guest = yes
; writable = yes
; printable = no
# The following two entries demonstrate how to share a directory so that two
# users can place files there that will be owned by the specific users. In this
# setup, the directory should be writable by both users and should have the
# sticky bit set on it to prevent abuse. Obviously this could be extended to
# as many users as required.
;[myshare]
; comment = Mary's and Fred's stuff
; path = /usr/somewhere/shared
; valid users = mary fred
; public = no
; writable = yes
; printable = no
; create mask = 0765
[Series]
comment = TV Series
path = /home/Kirby/Series
public = yes
only guest = yes
writable = yes
printable = no

875739 wrote:
Hi Im new to solaris and trying out ZFS which has been great.
Im haivng some trouble that I cant find up to date info on so here goes:
First how do you mount an NTFS volume in Solaris 11 Express?
I need to access the data on an NTFS drive to populate my new ZFS tank.I never had a need for it but I think you'll have to compile fuse ntfs-3g manually.
http://web.archiveorange.com/archive/v/u46DbWSGcIzl7pexf4hQ
>
Secondly, I have read only access on my samba shares from windows machines but my smb.conf looks right. a copy of my smb.conf will follow
Any suggestions would be appreciated.You don't need to use Samba in Solaris 11 Express.
http://download.oracle.com/docs/cd/E19963-01/html/821-1448/gaynd.html#gayne

SPARCengine CP1500 & Solaris 2.5.1.?

Similar Messages

Maybe you are looking for