Speaker Wire

I just bought the 7.1 creative s750 speaker system, and I was wondering if anyone knows any kind of speaker wire I could use that is a little higher performance than the speaker wire that comes with the system? I have looked around and I can't find speaker connections with one end an RCA connection, and the other end a positive, negative end to plug into the back of the speakers. If anyone knows where I could find that type of speaker wire that is hire end, I would really appreciate it.

You could plug them into the 3.5mm speaker output on the back of the computer.
Yes, there are speaker wire to RCA and then RCA to 3.5mm headphone plug cables/connectors.
But that wouldn't really be good as the power otuput of the computer (500-600 mWatts?) would not be enough to power the speakers to an acceptable level (probably 1 watt minimum).

Similar Messages

Connecting traditional speaker wire to Airport

I just moved into a house with speakers installed in the ceilings. The connection wire for the speakers is traditional +/- (black/red) speakerwire. I'm trying to figure out the best way to connect that wire to my Airport so that I can use my PowerBook as a jukebox throughout the house.
Right now I've got it hooked up through a series of connectors from Radio Shack, but they definitely hurt the sound quality. Any suggestions on a more elegant, simple solution to this problem?
thanks!

You need some kind of simple amplifier, and an Aiport express for streaming iTunes.
If the speaker wires are in multiple locations, you'll need multiple amplifiers and multiple AX's

1/8 inch to speaker wire?

I use an Apogee One with my Macbook. I have a pair of old speakers that use regular speaker wire. I would like to connect those to the output jack on the Apogee Duet. Anybody know the easiest way to do this? Does anybody manufacture something that converts from 1/8 to speaker wire?
(my original message said 3.5 mm to speaker wire - I think I mean 1/8'' to speaker wire)
Message was edited by: Lizard Man

Hi,
I tried finding out a converter for your 3.5 mm speaker wire to 1/8" gauge but I only found one that goes from 3.5mm to 1/4." The best thing to do is soldering the wires evenly into your Apogee.
Check this link I found a guy had a similar problem:
http://www.neoseeker.com/forums/1/t1233149-standard-speaker-wire-to-3-5mm-1-8-ja ck-converter/
Hope this info helps,
Vicente

IPhone to speaker-wire speakers.

I'm not really a 'speaker guy' I know how to take two pieces of wire and plug my big speakers into the standard dvd surround sound player and all that. But I had a rather interesting idea today that I am sure someone else has thought of before.
I have to extra speakers, they are old wooden ones that still play beautifully and are mounted on the walls in my bedroom with speaker wire running from below them to behind my tv. They are not hooked up to anything, what I was wondering how to do is hook these up to the iPhone Dock.
Is there a product made by bestbuy or radio shack that has the left channel and right channel things like on my speakers with the red and black wire that go into the two spring loaded parts and THEN a headphone jack behind it? This would be really convenient but I'm just not sure how to put this entire post into a google search So I came here.
Thanks,
-Brandon

You can't run unpowered speakers from the iphone, or an ipod, etc. Things like computer speakers are powered, and accept a line level input from a source device. Your wooden speakers need an amplifier that takes the iphone as its source. So if you can hook them up to a receiver, you can run your iphone into the receiver with a standard stereo to 3.5mm splitter, into the AUX or another input on the receiver. If not, you'll have to pick up an amplifier capable of driving those speakers.

Speaker wire tags/labels

WE're about to switch our Home Theater around, and will be running surround sound speaker wires through the walls, instaed of those wire/cable channels, and it would just be great to have tags/labels attached to the speaker wires so that we will know which wires go to want input. Thank you in advance.
Solved!
Go to Solution.

CaJazzman wrote:
What we're looking for for is something more permanant, so that we can leave on each run. But, thank you anyways for your reply.
I've had the orginal tape on my speaker wires for over a decade now. It's made it through three sets of speakers and 4 AVR's. It's cheap, easy, and effective. You could go buy a labeler or some 'speaker wire labels' if you want, but for something that's going to stay immobile and hidden you're really just paying more than you need for fanicer tape.
There's really no need to overthink this.

Speaker Wire For T7700?

I have a quick question,
Does anyone know where I can buy a full set of speaker wire for the Inspire T7700 Speaker Set by Creative Labs? I am moving and I need a new set of speakers because my current set was wired into the house.
Thanks in advance for your help!

I have a quick question,
Does anyone know where I can buy a full set of speaker wire for the Inspire T7700 Speaker Set by Creative Labs? I am moving and I need a new set of speakers because my current set was wired into the house.
Thanks in advance for your help!

All speaker wires and no music...

Hi,
I just renovated my apt and installed speaker wire on each room...
Now I want to play music :-) but I don't know what kind of equipment I need.
So far I've been using a portable CD player.
If possible I'd like to set the volume in room independently
Thanks,
SWK

Do you have any audio gear other than a CD player? If you want to control volume in all the rooms you will need a volume control for each set of speakers in each room. These are usually in wall controls and will fit in a standard electrical box. Do you want just a stereo reciever and speakers in all rooms or are you wanting a surround system with speakers in all rooms?
Bob

Inspire T3000 - Speaker Wire Broke

Ok, you can laugh all you want, but I doubt this is the first time something like this has happened.
I bought my Inspire T3000's on 2/7 and I'm very pleased with them. However, my cat chewed through one of the speaker wires and I'm interested in purchasing a single T3000 speaker to replace it. How should I go about doing this? I did not find any way to purchase spare or replacement parts via the creative website, but I am sure there is a way they can accommodate me.
Any and all help would be greatly appreciated. Thanks!

Okay I will not lye I did laugh lol because I know cats love to chew on our technology but if you did not want to wait for the replacement wire just fix it yourself and I will walk ya through that below.
First cut the 2 ends nice and even the peel each side of the wire back so you can peel there coating off now one will be Black and the other Red on both ends of the cut in half wire one will be positive + Red or White and the other will be Negative - Black just cut the other end of that broken wire like you did one side then match the colors togeather like a puzzle then twist the wires togeather then if you want I preferr solider but if you can't get ahold of this the electrical tape will do just tape the wires up so they can't touch eatch other and when your done they will work fine and withstand minors pulls and tags but not cats
hope this is better help to you

Missing s750 speaker wire

does anyone know where i can go about getting replacement speaker wire for the s750? i've moved a ridiculous amount of times and lost track of my rear speaker cables.

From what I can tell from my S750s, you should be able to go to any Radio Shack and buy a new wire. Just make sure that the plug in to the Sub woofer is the right size on the one end and it really wouldn't matter what the other end is because you plug in bare wire to the actual speaker itself. Find a 2 wire... err WIRE with the right connector for the Sub and strip it on the other end to connect to the speaker. Sound simple... yes? Make sure you get the right length of wire!

Replace speaker wire

I have one FPS1500 and one speaker wire is broken. How i can disassemble this speaker to weld the wire again again?Antonio

I've replaced the front speaker wire on my s750's with QED 25th anniversary silver plated wire.You will need to desolder the wires inside the speaker and resolder some new wire taking note of the +- terminals,then connect the other end of the wire to an RCA connector(if thats what these speakers use)making sure to connect the + wire to the centre terminal of the RCA connector and the - to the outer section.A fairly easy and straightforward job if you can use a soldering iron. Hope this helps

Speaker wire cut, want to fix myself - which is the best way to connect the wires back together?

Some how, one of the wires going to my left-center speaker got cut in half. Not sure if it was the vacuum or my dog........anyway, I want to fix it, so - would you recommend butt-connectors, soldering the wire back together, or some other method?
Also, does it matter which wires connect back together? The wires are identicle (smooth covering) and both wires appear to be copper........ I was just wondering if anything would happen if you were to connect the wires back together, but backwards.
Please let me know so I can get this fixed quickly.
Thanks,
-Officer_Dufus

http://www.eminent-tech.com/music/multimediatest.html
Go to the above link and listen to the Pink Noise Monaural and the Pink Noise with Reversed Polarity tests. When a speaker is of opposite polarity, that means that the wires are connected backwards (positive to black and negative to red). If this happens, when your speaker should move out it'll move in and vice versa. This makes the sound seem to come from everywhere but the speaker. Play the tests to see what I mean.
If you solder your wires back together and notice this problem with your speaker, just reverse the connection to the speaker itself and you should be okay.

Creative GigaWorks Pro Gamer G500 Speaker wire question

Hi,
I have the creative gigaworks pro gamer speaker system but need to obtain some extra wire for the speakers to I can set them up around my room correctly. Would anyone have any suggestions of the type of wire to get hold of, room dimension is 98 inch by 24 inch. the main thing I am concerned about is the connectors for the wire going into the back of the amp, and the connectors going into the back of the speakers. I can twist the bare copper wires and insert them that way, but would prefer to have some sort of connector pin that can be used instead such as a gold plated connector. I think the gauge I am looking at is 6. Any help appreciated. Cheers
Message Edited by fs_shadow on 10-27-2007 07:49 AM

Have you checked your wiring? When going into THX Console and running the test, you should be able to hear the sound coming from the corresponding speaker. Otherwise your wiring must be wrong.
Also I do not understand what exactly you are doing in the CMSS Options: <EM>put the cmss3d on surround</EM>
Do you mean Stereo Surround?
<EM>put cmss 3d in the center </EM>: You mean you drag the slider into the center, or do you mean the CMSS2 option?Message Edited by alexs3d2 on 06-24-2006 07:34 PM

100 ft. speaker wire for Inspire P7800 90 Watts 7.1 Speakers?

I just bought this speaker set and want to wire them in a pretty big room. I'm going to need about 00 feet. What is the best kind (guage, characteristic resistance)? Thanks

I had this same problem once b4. They worked then they didnt. Something had changed on my machine and with a little investigation i found it. When you installed your product it asked you if you wanted to select "Digital Output Only". My system was analog and i didnt know it (inspire t7700, with audigy 2 zs).
I selected digital output only and when i finished installing i had absolutely no sound. I ran all kinds of tests and everything turned up the same. I went to Start>All Programs>Creative>Creative sound blaster audigy 2 zs> and clicked creative restore defaults. BLAMO everything worked. I looked at my Speaker Selection Control....the one where you can calibrate and use the bass control......and i noticed that the digital output only box was unchecked. i realized then what the prob was....but to make sure i tested it by clicking it again. and BLAMO no sound again. if you have digital speakers set the out put to digital only. also in the thx console there is an option to change the sampling frequency from 48khz to 98khz. just fyi
reply and let me know what heppened
Message Edited by OL_Ace on 08-11-2005 11:45 AM

GigaWorks T20 - can anyone tell me the length of the speaker wire?

Hi I'm looking to purchase the T20s for use in my bedroom with an mp3 player. I want to place one speaker on each side of the (double) bed on bedside tables. What I need to know if anyone can help, is the length of wire/cable between the two speakers so I can determine whether it is long enough for my planned set up. The Creative site does state that the package includes "stereo-to-stereo audio cable (2m)" - however I'm not sure whether this refers to the cable between the speakers or if this cable is for some other use. Can anyone assist?Many thanks

Hi I'm looking to purchase the T20s for use in my bedroom with an mp3 player. I want to place one speaker on each side of the (double) bed on bedside tables. What I need to know if anyone can help, is the length of wire/cable between the two speakers so I can determine whether it is long enough for my planned set up. The Creative site does state that the package includes "stereo-to-stereo audio cable (2m)" - however I'm not sure whether this refers to the cable between the speakers or if this cable is for some other use. Can anyone assist?Many thanks

LIVE 5.1 - NO SOUND FROM CENTRE SPEAKER - WIRES

NO SOUND FROM CENTRE SPEAKER ?WIRES & PLUGS SEEM OK !ANY IDEAS

plus I have switched around speakers & wires, so its not a speaker problemit must be the centre output ?could it be a hardware fault or software related

Speaker Wire

Similar Messages

Maybe you are looking for