Specific OID for A radio modules on 1200 series access points

Is there a specific OID for A radio module cards of the following type:
Flap - AIR-RM21A-A-K9
Dipoles - AIR-RM22A-A-K9

No switches in Cisco's current product line provide enough power to support both radio modules in the 1200 series. The (now optional) power injector for the 1200 will provide enough inline power for both radios, if that is an acceptible option.
Cisco has plans for several switches that will be able to provide inline power to both radios, but I am not aware of ETA's on these.

Similar Messages

1200 Series Access point

Hi Friends,
We have lot of 1200 series Anonymous access point in our environment.Radio module of part numberAIR-RM20A will not support WPA2.
is it possible to check radio module part number by CLI ?
If yes please share with me . . .

The command is show controller dot11radio 0 or show controller dot11radio 1
-Scott

1200 Series Access points

I have an problem with multiple access points losing the ability to telnet to them.They access points work fine but the only way I can get the ability to telnet back is to restart them. Has anyone else had this problem.

I am using Radius. This is what the config looks like.
Thanks for your help Greg
line con 0
password 7 110B15041317
login authentication local_auth
transport preferred all
transport output all
line vty 0 4
password 7 104C05180112
login authentication rad_auth
transport preferred all
transport input all
transport output all
line vty 5 15
password 7 104C05180112
login authentication rad_auth
transport preferred all
transport input all
transport output all

Symbol Netvision Phone w/Cisco 1200 series Access Point

I am running 802.11b access point my phone can associate and get an ip address from my call manager but I keep getting "not registered" "registered". I and then I lose association to the access point. I have 2 vlans on one access point one for voice and one for data. Please let me know if someone has a work around or a fix.
Stan

Stan,
Sounds like you have an interference problem.
What did your site survey show up in terms of other AP's and overlapping coverage areas ? Try a new channel that has the 2 channel separation from other busy channels and maybe even try a new/better placement of the AP
effectivly what you have now is the equivalent of pulling out the cable and plugging it back in constantly on a standard IP phone this means you will not be able to make calls
What firmware you running on the AP ?

Cisco aironet 1200 Series access point dropping clients

We are having an issue where our Cisco Aironet 1220 Series AP is constantly dropping clients. We have 3 APs mounted on a single tower, all out of each others range and freq. There are approximatly 30 clients on each AP. We are noticing an increase in dropped customers (up to 20 at a time). ANy suggestions? This only became an issue in the last few weeks, and nothing major has changed.

Hi
Even I was facing almost the same kind of problem. But in my case it was wired clients to the workgroup bridge 350.
I had done lot of testings and reading at that time to resolve this problem.
However in your case I feel your problem can be resolved by keeping the option "Reliable multicast for Workgroup bridges" disabled in the APs under dot11radio interface settings. This is possibly because the radios cannot associate to more than 20 clients at a time if the option is in the enable mode.
You need to keep this option enabled in a root bridge when you have problems of dropping the wired clients to the workgroup bridge.
By keeping this option enabled, you are actually asking the Root bridges to consider the Workgroup bridges as Infrastructure devices and not as clients thereby making the roots to send all the multicasts to the WGBs. However in that case it losses the efficiency of associating more than 20 clients.
Let me know if this resolves your problem.
Regards

OID for AGM/ADM modules

I have 4 modules 2 AGM and 2 ADM install in 7609, I need to integrate this information to a system of monitoring as FMS, one requires the detail of the OID, and the value of the variable that is required to manipulate (to show in alert status).
Unfortunately in Cisco I have not found this level of details.

I don't know if this works on a 7609 (worth a try) but on my ASA5510 there is a hidden command:
show snmp-server oid
It lists every OID available to use.
Hope this helps.

Mib for reading/setting RF channel on standalone Access Points

Hei Everybody. Does anybody know if there is a SNMP mib sfor reading/setting RF channel and other RF-parameters on 1131AG standalone Accesspoints. In my network we are using the "least congested frequency" choice for Channel selection and wants to se what the result for this is.
Regards, Roy

"Least Congested Frequency" does not work.... either set your AP's to a specific channel or only highlight channels 1, 6, or 11. You can use a mib browser to seethe mib listing... this link migh help... son't know if its different from the 1131AG:
http://www.oidview.com/mibs/9/CISCO-DOT11-IF-MIB.html

Recomended ios for 1200 series?

Any suggestions for most stable and bugfree ios to use on the AP1200 series?
For me it looks like the 12.3(8)JEA3 should be ok after reading about caveats in the release notes. Only something about shared authentication in non-native vlans and two other minor things. Our setup has 8 ssids with 4 of them with wpa-psk authentication that works ok with this version.
Its a little confusing wich version to choose with all that numbers and release dates.

Only some versions can be upgraded:
For all IOS-based 1200 series modular access point (1200/1220 Cisco IOS Software Upgrade, 1210 and 1230 AP) platforms, it depends on the radio:
–if 802.11G, MP21G and MP31G are supported
–if 802.11A, RM21A and RM22A are supported
The 1200 series access points can be upgraded with any combination of supported radios: G only, A only, or both G and A.
http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp157130

Setup new access point 1200

hi
i have problem in install new access point 1200
the access point now not connect to any device iam connect the access point using ethernet cable to PC to configure it i try to using GUI but i can not iam setup the PC with ip address 10.0.0.2 and GW 10.0.0.1 and i try to enter to access point but i can not
i try to use CLI and i connect the access point to PC using console cable and now iam enter to it after the access point start i try to enter to config ter but i can not i get error when i check the command i can not see this command and when i read the manual its tell me to setup ip address using command (lwapp ap ip address) and i try to save ip address using command wr mem or copy run start but i cannot i get error
in prevelig mode i get only this command
clear Reset functions8B5E500 00001537 61300D06 092A8648
clock Manage the system clock
crypto Encryption related commands.
debug Debugging functions
dir List files on a
led LED lock Lock the terminal
more Display the contents of a file
name-connection Name an existing network connection
no Disable debugging functions
ping Send echo messages
pwd Display current working directory
release Release a resource
reload Halt and perform a cold restart
rename Rename a file
renew Renew a resource
rmdir Remove existing directory
save Start to save raise_interrupt_level stack
send Send a message to other tty lines
set Set system parameter (not config)
show Show running system information
systat Display information about terminal lines
terminal Set terminal line parameters
test Test subsystems, memory, and interfaces
traceroute Trace route to destination
undebug Disable debugging functions (see also 'debug')
upgrade Upgrade software
verify Verify a file
where List active connections
how i can setup it and how i can enable the radio
when i see sh run i see that the ip address is dhcp
can any one help me please
thanks

Hi Nassem,
It looks like you ended up with a Lightweight AP (LAP Part#) instead of an IOS AP. This can be fixed;
Reverting the Access Point Back to Autonomous Mode
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
You can convert an access point from lightweight mode back to autonomous mode by loading a Cisco IOS Release that supports autonomous mode (Cisco IOS release 12.3(7)JA or earlier). If the access point is associated to a controller, you can use the controller to load the Cisco IOS release. If the access point is not associated to a controller, you can load the Cisco IOS release using TFTP.
Using a TFTP Server to Return to a Previous Release
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, and c1240-k9w7-tar.default for a 1240 series access point.
Step 4 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 5 Disconnect power from the access point.
Step 6 Press and hold MODE while you reconnect power to the access point.
Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 8 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 9 After the access point reboots, reconfigure it using the GUI or the CLI.
From this doc;
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
Hope this helps!
Rob

1200 Series - Tagged Management VLAN Traffic

Hi,
As per my understanding the 1200 Series Access points running IOS (12.2(15)XR) send the management traffic (RADIUS,Accouting NTP etc) un-tagged i.e. using VLAN 1.
As per our current setup, we assign this un-tagged traffic to a different VLAN (by changing native vlan to x for the Trunk Port) on the cisco switch.
Is it possible to configure the Access Point to send Management Traffic as tagged with a particular VLAN id ? (Similar to what it does for Wireless Traffic, when SSID are associated to specific VLANs)
We are trying to set this up with a 3-Com 4400 series switch i have been unable to configure the 3-Com switch, so that it can assign the untagged traffic to different VLAN instead of VLAN 1.
Regards \\ Naman

Changing the Native VLAN doesn't make a difference. I can create any VLAN and make it native but management traffic is still being sent un-tagged.
Below was the setup i tested
AP--->Trunk Link<->Switch Port(Native VLAN=15)
Switch Port --->Trunk Link<->Router with VLAN15
I can make any VLAN as native VLAN on the AP and it doesn't effect the functionality as long as the Switch Native VLAN matches to the corresponding VLAN on the router.

IOS to LWAPP for 1130AG Access Points

We have initially installed IOS-based 1130 APs. If we would be upgrading it to LWAPP mode, could we pushed IOS-to-LWAPP upgrade thru the network? what procedures are required?

Hi Leopoldo,
This is possible and fully supported and can be done using the "LWAPP Upgrade Tool". Have a look at the following;
LWAPP Upgrade Tool Troubleshoot Tips
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a008072d9a1.shtml
Access points must run Cisco IOS Release 12.3(7)JA or later before you use the upgrade tool.
System Requirements
You can use the Autonomous to Lightweight Mode upgrade tool to install Cisco IOS Release 12.3(11)JX on these access points:
All 1100 series access points containing MP21G (802.11g) radios
***All 1130, 1230, and 1240 series access points
All modular 1200 series access points running Cisco IOS software and containing these supported radios:
802.11g: MP21G, MP31G
802.11a: AIR-RM21A-x-K9, AIR-RM22A-x-K9
All 1300 series access points in access point mode
http://www.cisco.com/en/US/docs/wireless/access_point/ios/release/notes/b311jx1.html
Cisco has released a free tool called the "Autonomous to Lightweight Mode Upgrade Tool" that allows selected Cisco Aironet autonomous access point models to be configured for lightweight mode operation.
The Autonomous to Lightweight Mode Upgrade Tool supports the following models:
Cisco Aironet 1240AG Series access points
Cisco Aironet 1230AG Series access points
Cisco Aironet 1200 Series access points that contain 802.11g (AIR-MP21G-x-K9) and/or second-generation 802.11a radios (AIR-RM21A-x-K9 or AIR-RM22A-x-K9)
Cisco Aironet 1130AG Series access points
**Cisco Aironet 1100 Series Access Points that contain 802.11g radios (AIR-AP1121G-x-K9)
Cisco Aironet 1300 Series Access Points/Bridges (AIR-BR1310G-x-K9 or AIR-BR1310G-x-K9-R). A Cisco Aironet 1300 Series operating in Lightweight Access Point Protocol (LWAPP) mode only operates as an access point. This series does not support LWAPP bridging mode.
The Autonomous to Lightweight Mode Upgrade Tool supports a process to migrate an autonomous access point from autonomous mode to lightweight mode. Unlike a VxWorks to Cisco IOS Software upgrade, this process is a Cisco IOS Software upgrade to the existing Cisco IOS Software image-not an operating system "swapout". In converted access points operating in lightweight mode, Cisco IOS Software continues to run on the access point, while LWAPP is used to communicate with a wireless LAN controller. Since LWAPP supports automatic access point configuration, there is no need to retain or convert the original autonomous Cisco IOS Software access point configuration.
http://www.cisco.com/en/US/netsol/ns340/ns394/ns348/ns337/networking_solutions_white_paper0900aecd804f1a23.shtml
Cisco Aironet Access Point Support for Lightweight Access Point Protocol
http://www.cisco.com/en/US/products/ps6521/prod_bulletin0900aecd80321a2c.html
Upgrading Autonomous Cisco Aironet Access Points to Lightweight Mode
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp157147
Hope this helps!
Rob

Cisco 1230 access point a radio lightweight mode

Will the cisco 1230 access point work in lighweight mode if it is using a radio?

The 1230 can be upgraded to LWAPP with the A Radio model listed below;
Solution Requirements
Migration from autonomous access point mode to lightweight mode is possible on these Cisco Aironet access point platforms:
All 1130AG access points
All 1240 AG access points
For all IOS-based 1200 series modular access point (1200/1220 Cisco IOS Software Upgrade, 1210 and **1230 AP**) platforms, it depends on the radio:
if 802.11G, MP21G and MP31G are supported
if 802.11A, RM21A and RM22A are supported
The 1200 series access points can be upgraded with any combination of supported radios: G only, A only, or both G and A.
All 1310 AG access points
From this good doc;
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html
Hope this helps!
Rob

Any Specific patches for General Ledger on Release 12.1.3

All -
I came to know we can migrate oracle apps *12.1.1 to 12.1.3* by implementing update pack - (*Patch 9239090*)
But are there any specific patches for General Ledger Module on release *12.1.3*
Please advise on this
Regards
VSH

I came to know we can migrate oracle apps *12.1.1 to 12.1.3* by implementing update pack - (*Patch 9239090*)
But are there any specific patches for General Ledger Module on release *12.1.3*
Please advise on thisPlease see the docs under the "2. Recommended Patching" section in (EBS R12 Period Close Advisor: General Ledger [ID 1359476.1]).
Also, please the docs referenced in these docs.
Planning Your Oracle E-Business Suite Upgrade from Release 11i to Release 12.1 [ID 987516.1]
E-Business Suite: Oracle Financial Control Information Center [ID 1207527.1] -- GENERAL LEDGER
Oracle Applications Current Patchset Comparison Utility - patchsets.sh [ID 139684.1]
My Oracle Support > Patches & Updates > Recommended/Latest R12 Patches
Thanks,
Hussein

Which access point is better for hospital environments?

Folks,
I have a customer in hospital, who requires to have wireless deployed everywhere. The fact is , customer is budget concious, so I designed in such a way to place it in corridors , so that wireless coverage could get inside the rooms, but the doors are fire-proof which blocks RF .
What are the best practices in deploying AP's in hospital, for eg: is it safe to install AP's next to Medical Imaging Room or other devices which may cause interference
Which model is suitable for this sort of installation?
Thanks,
SID

Hi SID,
Please consider in your budget for a Wireless LAN Site Survey. WLAN Site Survey will allow you to better understand WHERE to deploy your AP's and HOW MANY AP's to deploy. When deploying an AP, also bear in mind for AP failures. You can address this issues with either keeping "spare" stocks or putting additional AP's per floor so when an AP would fail, the WLC will calculate and increase the transmission power to cover the loss of an AP.
In regards to what models to buy, I'd recommend looking at the 1140 or the 1250. These AP's are geared up for Draft N (2.0 Ratified).
For AP's that are geared up for 802.11N (Draft 2.0):
Data Sheet Cisco Aironet 1140 Series Access Point
http://www.cisco.com/en/US/prod/collateral/wireless/ps5678/ps10092/datasheet_c78-502793.html
Data Sheet Cisco Aironet 1250 Series Access Point Data Sheet
http://www.cisco.com/en/US/prod/collateral/wireless/ps5678/ps6973/ps8382/product_data_sheet0900aecd806b7c5c.html
If you are going to choose the 1250, note that the Antennaes are optional. Here's some information regarding them.
Antenna Product Portfolio for Cisco Aironet 1250 Series Access Points
http://www.cisco.com/en/US/prod/collateral/wireless/ps7183/ps469/at_a_glance_c45-513837.pdf
The AP1250, when operating with 2 radio modules on Autonomous IOS, requires a minimum of 18.5 watts (ePoE). So you'll need either a Power Injector or PoE switch that will support enhanced PoE such as the 3560-E or 3750-E.
Cisco Nurse Connect Solution
http://www.cisco.com/web/strategy/docs/healthcare/nurse_connect_aag.pdf
Hope this helps.

Mail for Exchange - Access Point question

Hello,
When setting up Mail for Exchange, you need to input the Access Point. I cannot find an option to select "Ask for Access Point" or something along that line.
I use wireless access points and when I go from one spot to another I have to change my settings just to sync.
Does anyone know of an option, if not how could I file for a feature request?

The specific problem can be resolved. How did you hard reset your phone? You should hard reset your phone (some key combination which I cannot remember, press four keys simultaneously). Then format mass memory. Reinstall the firmware. Otherwise let Nokia Care reflash your phone. I had issues with freezes when I hung up a call, but that was resolved when Nokia Care reflashed my phone.
My phone is currently broken, so I cannot help you further.
Erik

Specific OID for A radio modules on 1200 series access points

Similar Messages

Maybe you are looking for