Specific Settings for external and internal display modes?

Does anyone know if there is a way do have different settings that adapt to whether I'm using my Macbook's internal display or am docked to my 23" external Cinema Display at home? It would be nice if the Dock would be small and on the side "internally" and large and at the bottom "externally." Also its a pain if I've expanded a window on my external, then disconnect and have to tidy up my windows again so they fit on my smaller internal dispaly

Hi
Check this document
Page 35 shows how to change icons
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/504e31fc-f46f-2910-98b4-dd94478c22f8
Regards
Krishna.

Similar Messages

E-Recruiting for external and internal candidates

Hello,
I am looking for documents/guides that can show me how to configure E-Recruiting frontend (for external candidates) to point to the integrated ECC (HR + E-Recruiting) backend, and to configure SAP Portal with ESS (for internal candidates) to point to the integrated ECC backend. I am also looking to configure Trex 7.0 for E-Recruiting. I am unable to find any documents regarding this scenario. Can anyone help me locate some material?

Hi Vishal,
There is no standard field available but this requirement can be handled through an enhancement in the specific BSP page. In your requirement it will be personal details tab in candidate profile wizard and it would also necessiate to enhance infotype HRP5102 - candidate information with this field.
You can also refer the blog below contributed by Hemendra Singh Manral to understand how to go about doing this enhancement in the BSP.
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sap.km.cm.docs/library/other-topics/e-recruitment%20adding%20additional%20custom%20fields%20to%20requisition%20maintenance.pdf
Hope this information helps.
Best Regards
G Raj

Configure a sharepoint 2013 site for external and internal access

I need to configure a local install of sharepoint 2013 so that users can access it internally and externally using windows/AD authentication. The internal and external addresses are different.
I have bound an external ip to the domain for external access.
I have created Alternate Access mapping, and bound the host header but I get a file not found message for external access.
Have I missed something here? why the error and how can it be fixed. Step by step process would be appreciated.

Hi Luis,
According to your description, my understanding is that the error occurred when accessing the site externally.
The most common cause for this is that the IIS host header is configured incorrectly. The 404 will appear because we are hitting a different IIS web site and not the one we are intended to.
Here is a similar issue for you to take a look:
http://stackoverflow.com/questions/14953322/sharepoint-2013-404-not-found-while-accessing-site-collection-from-outside
More references:
http://technet.microsoft.com/en-us/library/cc261814(v=office.15).aspx
http://technet.microsoft.com/en-us/library/cc263208(v=office.15).aspx
Best regards.
Thanks
Victoria Xia
TechNet Community Support

External and internal mikes are not automatically switching over either recording or on voice calls

My laptop model name is HP Pavilion dv4-1100ea which is shipped with Vista Home premium 32 bits and has got service pack 1.
Restored the laptop to factory setting since then I am having the following problems; I had the same problem when my laptop was brand new and whenever I reset the laptop to factory setting I get the following problems:
1. External and internal mikes are not automatically switching over either in middle of the recording using sound recorder or while the call in progress on voice calls (skype):
   Using the sound recorder if I start recording the sound with external mike and in-between recording if I switchover from external mike to inbuilt mike and later on when I play back I can only hear the sound up till where I used the external mike during recording, after the switchover to inbuilt mike I cant hear any sound.
   But if I start the recording with inbuilt mike and in between recording if I plug in the external mike and later on when I play back I can only hear the sound up till where I used the inbuilt mike during recording , after the switchover to external mike I cant hear any sound.
   So in brief both my external and internal mikes are working fine, only problem is that if I start recording (using sound recorder) or voice call with one specific mike, I have to continue with it till the end. I can’t switchover to another mike in between the conversation (voice call) or recording, if I do so, I have to select the mike manually in chat software but while recording I cant even select manually because in laptop, it takes the mike whichever is in current use as default mike in recording tab(sound window). The green tick automatically (in recording device tab) switches over according to the use of mike. Though the green tick in the recording tab is switching over automatically according to use of mikes, its not picking up the sound after switch over during recording.
2. And also when I click on recording device tab in sound window and plug in external mike, though the green tick automatically switchovers from internal to external mike, while I speak both internal and external mikes volume meter respond to the sound inputs by rising and falling but if I take out external mike, green tick goes to internal mike and when I speak only internal mike volume meter respond to sound rising up and down not the external mike.
To resolve the issue I have tried following steps with no luck:
1.I have checked the mikes(internal and external) properties, the both mike shows to be enabled in general tab, in level tab the volume is set to 100 and in advanced tab , all options are selected.
2. In device manager I have got only one audio driver named as “IDT High definition Audio CODEC”. I have uninstalled the audio driver and reinstalled it using scan for hardware option
3. Uninstalled the audio driver in device manager and reinstalled the audio driver using recovery manager > advanced option> hardware driver re-installation.
3. I have updated the BIOS(Insyde F.65, 12/02/2010).
4. I tried to update the audio driver using below link but things went more worse so I did system restore (not factory setting though).
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-67051-1&lc=en&dlc=en&cc=us&...

Sounds like you need to upgrade to the iPhone 5s
The 5s has Touch ID
You can unlock your phone with your finger instead of typing in a key code
No swiping to unlock either, just touch the home button
You can enrol multiple fingers as well
Here is a video of it in action
http://www.apple.com/iphone-5s/videos/#video-touch
Or wait and see what iPhone 6 has to offer
That being said, as desiel vdub posted if the phone is up to your face, the proximity sensor should turn the screen off
And when you lower the phone turn it back on again
Not sure about the phone locking when your on a call doesn't sound right

User specific settings for message ME161

All SAP Gurus,
Is it possible to have user specific settings for message like ME161?
We want the message ME161 to be displayed as warning message to one user and the same message to be displayed as an erorr message to another user.
Is it possible?
Regards,

hi,
In addition to the above data:
Messages are defined like this:
Version AG No. Text TYPE
Normally, in std case,
Version will be always 00 for system defined messages....
Now if you wanna make the the same message as authorised,
then copy this exsisting message....
While copying system will ask for version, here enter it it Z*
Now on the other hand make the other settings for user/user grp in SU01 and here set the user parameter as MSV(THIS IS MUST)....
and then try...
Regards
Priyanka.P

What are the settings for datasource and infopackage for flat file loading

hI
Im trying to load the data from flat file to DSO . can anyone tel me what are the settings for datasource and infopackage for flat file loading .
pls let me know
regards
kumar

Loading of transaction data in BI 7.0:step by step guide on how to load data from a flatfile into the BI 7 system
Uploading of Transaction data
Log on to your SAP
Transaction code RSA1LEAD YOU TO MODELLING
1. Creation of Info Objects
In left panel select info object
Create info area
Create info object catalog ( characteristics & Key figures ) by right clicking the created info area
Create new characteristics and key figures under respective catalogs according to the project requirement
Create required info objects and Activate.
2. Creation of Data Source
In the left panel select data sources
Create application component(AC)
Right click AC and create datasource
Specify data source name, source system, and data type ( Transaction data )
In general tab give short, medium, and long description.
In extraction tab specify file path, header rows to be ignored, data format(csv) and data separator( , )
In proposal tab load example data and verify it.
In field tab you can you can give the technical name of info objects in the template and you not have to map during the transformation the server will automatically map accordingly. If you are not mapping in this field tab you have to manually map during the transformation in Info providers.
Activate data source and read preview data under preview tab.
Create info package by right clicking data source and in schedule tab click star to load data to PSA.( make sure to close the flat file during loading )
3. Creation of data targets
In left panel select info provider
Select created info area and right click to create ODS( Data store object ) or Cube.
Specify name fro the ODS or cube and click create
From the template window select the required characteristics and key figures and drag and drop it into the DATA FIELD and KEY FIELDS
Click Activate.
Right click on ODS or Cube and select create transformation.
In source of transformation , select object type( data source) and specify its name and source system Note: Source system will be a temporary folder or package into which data is getting stored
Activate created transformation
Create Data transfer process (DTP) by right clicking the master data attributes
In extraction tab specify extraction mode ( full)
In update tab specify error handling ( request green)
Activate DTP and in execute tab click execute button to load data in data targets.
4. Monitor
Right Click data targets and select manage and in contents tab select contents to view the loaded data. There are two tables in ODS new table and active table to load data from new table to active table you have to activate after selecting the loaded data . Alternatively monitor icon can be used.
Loading of master data in BI 7.0:
For Uploading of master data in BI 7.0
Log on to your SAP
Transaction code RSA1LEAD YOU TO MODELLING
1. Creation of Info Objects
In left panel select info object
Create info area
Create info object catalog ( characteristics & Key figures ) by right clicking the created info area
Create new characteristics and key figures under respective catalogs according to the project requirement
Create required info objects and Activate.
2. Creation of Data Source
In the left panel select data sources
Create application component(AC)
Right click AC and create datasource
Specify data source name, source system, and data type ( master data attributes, text, hierarchies)
In general tab give short, medium, and long description.
In extraction tab specify file path, header rows to be ignored, data format(csv) and data separator( , )
In proposal tab load example data and verify it.
In field tab you can you can give the technical name of info objects in the template and you not have to map during the transformation the server will automatically map accordingly. If you are not mapping in this field tab you have to manually map during the transformation in Info providers.
Activate data source and read preview data under preview tab.
Create info package by right clicking data source and in schedule tab click star to load data to PSA.( make sure to close the flat file during loading )
3. Creation of data targets
In left panel select info provider
Select created info area and right click to select Insert Characteristics as info provider
Select required info object ( Ex : Employee ID)
Under that info object select attributes
Right click on attributes and select create transformation.
In source of transformation , select object type( data source) and specify its name and source system Note: Source system will be a temporary folder or package into which data is getting stored
Activate created transformation
Create Data transfer process (DTP) by right clicking the master data attributes
In extraction tab specify extraction mode ( full)
In update tab specify error handling ( request green)
Activate DTP and in execute tab click execute button to load data in data targets.

Prob creating ABAP Proxy-Interface use external and interna msg definition

Hi,
I've created a service interface using external definition (message type for request and response), imported via WSDL file. However, while creating ABAP proxy in SPROXY, it gave the error message "Interface uses external and internal message definition". I searched through the forum, the questions were raised but no definite answer was found. Is it not possible to generate a proxy if there is any external definition used?
Details of the error message:
Message no. SPRX122
Diagnosis
In a message interface you can use messages from different sources:
Message types and fault message types edited in the Enterprise Services Repository
Messages imported into the Enterprise Services Repository (external definitions, RFC, IDoc)
In the current message interface, message types from different sources have been used. Since messages from these different sources must be handled differently during proxy generation, such a mixture of messages within a message interface is not possible.
System Response
The interface cannot be generated.
Procedure
Change the interface definition accordingly in the Enterprise Services Repository.
p/s: My external definition is actually derived from a ABAP FM web service. The reason why i used external definition is that i try to avoid the tedious steps of hard-coding all the data types for the request and response message types.
Any help would be highly appreciated.
- julius

Hi Arvind,
For technical reasons, proxy generation and the respective editors in the Integration Builder do not support the entire language range of XML schema and WSDL. For an overview of which language elements are supported, see the Excel spreadsheet in the SAP Service Marketplace at service.sap.com/xi ® Media Library ® Documentation: SAP XI 3.0 (SP11) u2013 Supported XML Schema and WSDL (EN).
I couldnt find the above document in the service market place. Any hint to find it?
Thanks.
- julius

Issue with Visibility Settings for Backgrounds and Layers

I am using Acrobat Pro XI 11.0.10 (Windows) and having an issue with visibility settings for layers and backgrounds. I am attempting to get backgrounds to appear while viewing in Adobe Reader and Acrobat Pro but not be printed and so far have had no success.
When using a background the Appearance Options dialogue has "Show when printing" unchecked, but "Show when displaying on screen" is checked. This results in the background not showing on the screen, and the background will only appear once the box for "Show when printing" is checked. It looks like the option for printing is dictating whether or not the background is able to appear.
Using layers has not worked either. The background layer is set to "Never Prints", but will still show up when printed.
I was wondering if anyone else has run into this and has a solution, or has any recommendations.
Thanks in advance.

Hi setrev2012,
How are you adding the backgroud?
The only way I can think to accomplish this is via a watermark.
The basics...
Open PDF in Acrobat. Choose Pages > Watermark > Add Watermark.
Select a jpg or PDF of your background and adjust scaling options as desired.
Then click the Appearance Options.. and uncheck the Show When Printing option.
In this image the PDF is a blank page with the word "Test" on it. The watermark is the stamp and impression (a stock photo jpg).
If you want a solid color background, just create a flat image of the background color for use as the watermark.
If you have already followed the steps and still facing the issue then please share the file with me at [email protected] so that i can have a look.
Regards,
Rave

Make Flash Plug-In for Firefox Remember Privacy Settings for Camera and Mic Access on Local File

My company is using Flash Player to develop some kiosk-style applications to run on a standalone computer (no network connection). This computer will contain web pages containing Flash content. They will be opened from the local HD with Firefox with the Adobe Flash plug-in (v11.7.700.224). One of the applications accesses the microphone hooked up to the computer. When this application is started, it always asks for permission for "local" to access the microphone and camera. In previous versions of our system, we could click "Remember" if we did it once and that would make it so it wouldn't ask for permissions again (in this case, the Remember option isn't available, and the site settings don't even offer the Privace tab). However, in the previous case, we were running IE with a previous ActiveX Flash version (unfortunately, this approach is no longer available as we have had to switch to Windows 8 and that changes the game with IE and Flash entirely).
At this point, we have tried to use the Global Settings for "Camera and Microphone Settings by Site..." to enter "Local" as an always allowed site. This does not seem to have any effect. We also tried entering the root directory of the applications in "Trusted Location Settings", but that also seemed to have no effect.
I'm not sure what has fundamentally changed here. I think there might be some differences in the Plug-In version (compared to ActiveX), but I'm not sure what they might be or how to do the same thing as before.
Any help would be appreciated. Thanks in advance.
Torrey

Chris,
We learned that the Privacy tab (in Settings) can be found under the Flash plug-in for Firefox, but only if Firefox is running under an administrator.
Unfortunately, we haven't had much luck with the mms.cfg file. The following was used in the mms.cfg file (placed in both the %WINDIR%\SysWow64\Macromed\Flash and %WINDIR%\System32\Macromed\Flash” directories):
AVHardwareDisable = 0
AVHardwareEnabledDomain = local
AVHardwareEnabledDomain = 127.0.0.1
AVHardwareEnabledDomain = localhost
AutoUpdateDisable = 1
The AVHardwareEnabledDomain settings seem to be getting ignored regardless of whether the user is a standard user or an administrator. I also checked to make sure it wasn't just a local problem by going to a website that uses a microphone (http://www.testden.com/accent-reduction/systemcheck.htm). Adding the requested domain to the list (AVHardwareEnabledDomain = train.act360.com) still didn't bypass the allow/deny dialog box.
We know that the mms.cfg file is being read because setting "AVHardwareDisable = 1" will result in no prompt and that section being greyed out in Global Settings. I saw a post that suggested this setting was required to even make the AVHardwareEnabledDomain work, but it seems to block the local entirely and still brings up the dialog query on the internet site.
Thanks,
Torrey

What are policy firewall port should be permit between meetingplace web external and internal

I deploy MeetingPlace Web Conferencing with SMA.
1. What are policy firewall port should be permit between meetingplace web external and internal (web external on DMZ zone and web internal on internal zone)?
2. Synchronized Globally Unique Identifiers (GUIDs) between internal and external Web Servers used firewall port?

Hi,
List of Firewall pots to be opened are mentioned in following document, you can refer your deployment type and open ports as mentioned.
http://docwiki.cisco.com/wiki/Cisco_Unified_MeetingPlace_Release_8.5_--_System_Requirements_for_Audio-Only_Deployments
http://docwiki.cisco.com/wiki/Cisco_Unified_MeetingPlace_Release_8.5_--_System_Requirements_for_WebEx-Scheduling_Deployments
http://docwiki.cisco.com/wiki/Cisco_Unified_MeetingPlace_Release_8.5_--_System_Requirements_for_MeetingPlace-Scheduling_Deployments
Regards
Ronak patel

I get "mail server does not recognize your Apple ID and password" when I try to share a picture via email in iPhoto. My iCloud email works ok otherwise. I have check all mail settings for ID and password.

I get "mail server does not recognize your Apple ID and password" when I try to share a picture via email in iPhoto. My iCloud email works ok otherwise. I have checked all mail settings for ID and password.

In the iPhoto preferences ==> accounts delete the account and re-enter it - sometimes that resolves this
Or IMHO the best long term solution is to set Apple Mail as the iPhoto e-mail client in the iPhoto preferences and use it - it has a number of advatages and has fewer problems
LN

I have uninstalled and reinstalled iTunes several times, but keep getting an error message that "the registry settings for importing and burning CD's and DVD's is missing". Can anyone help with this?

I have uninstalled and reinstalled iTunes several times, but keep getting an error message that "the registry settings for importing and burning CD's and DVD's is missing". Can anyone help with this?

It keeps telling me to reinstall iTunes, but it continues to come back with the same error message.

[svn:bz-trunk] 7643: Add app server specific excludes for jboss5 and websphere7.

Revision: 7643
Author:   [email protected]
Date:     2009-06-08 13:32:14 -0700 (Mon, 08 Jun 2009)
Log Message:
Add app server specific excludes for jboss5 and websphere7.
Modified Paths:
    blazeds/trunk/qa/features/excludes.properties

Change settings for external displays: no "mirror displays" mode

Hello,
I'm using a 13" MBP with Snow Leopard. I'm using different displays and projectors in different locations. When you plug an external display in, the two displays are first in "mirror displays" mode. First thing I do is to switch this off.
Is there any way of changing the settings, so that an external display doesn't start in the synchronized mode??
Thanks in advance.
Message was edited by: robert170

only if you plug in this projector again. If you plug in a new projector (which I often do) it allways starts in "mirrored" mode.
I just found an app which - at least - makes the switching easier:
http://www.fabiancanas.com/Projects/MirrorDisplays/
Message was edited by: robert170

Two External Displays and Internal Display Over Different Connections

Hi there.
I'm going to be purchasing a rMBP in the very, very near future. However, I am unclear about how external displays work with this. My current display setup at work is two basic 1080p monitors that can be run over DVI, VGA or HDMI. I'd like to keep using these when I start using the rMBP but also gain the advantage of a third screen by using the internal display at the same time (so much space for activities!).
One of the thunderbolt ports will need to be used for an Ethernet connection (there is no wireless here), so this leaves the setup needing to be one monitor run via Thunderbolt -> DVI and the other monitor run via HDMI.
The internet in general isn't being entirely helpful with this. I'm looking for a clear answer of whether the rMBP will run the internal display and the two external displays using this setup under OS X. Some seem to believe that it won't work using different connection types, for example.
Thanks for any help.

Hello dljfield,
Thanks for using Apple Support Communities.
If you'd like to use multiple external displays with a MacBook Pro with Retina display, then please take a look at the information outlined below. A 15" MacBook Pro mid-2014 can support up to two external displays using different outputs.
MacBook Pro (Retina, 15-inch, Mid 2014) - Technical Specifications
OS X Yosemite: Connect multiple displays to your Mac
Take care,
Alex H.

Specific Settings for external and internal display modes?

Similar Messages

Maybe you are looking for