Speed issues with Windows 8.1, SSD, 32 GB RAM

I have windows 8.1 Pro, 64 bit, with 256 GB SSD containing the OS, 750 GB HDD storing data, 32 GB RAM, and 4 GB VRAM but still it tkaes 4 min to boot, 8 minutes to shutdown. I cannot change pagefile, it resets and goes to windows default, SSD gets full and
freezes the computer.
What should be done to make the computer operate at its best?
I have no virus issues or dirver problem.
Thanks and looking forward for an answer.
Rajeev

In order to diagnose your problem you will need to download and install the below
Install the WPT (windows Performance Toolkit) 
http://www.microsoft.com/en-us/download/details.aspx?id=30652
Help with installation (if needed) is here
When you have, open an elevated command prompt and type the following 
WPRUI.exe (which is the windows performance recorder) and check off the boxes for the following:
First level triage (if available), CPU usage, Disk IO.  
If your problem is not CPU or HD then check off the relevant box/s as well (for example networking or registry)  Please configure yours as per the below snip.  This will reboot your computer so save your data before
starting.
Click Start
Let it run for 60 secs or more and save the file (it will show you where it is being saved and what the file is called)
Zip the file and upload to us on Onedrive (or any file sharing service) and give us a link to it in your next post.
Wanikiya and Dyami--Team Zigzag

Similar Messages

  • Itunes issues with windows 8... laggy?

    anyone one else having abit a of laggy issue with playing music on windows 8?
    i just upgraded to windows 8 con. preview, and its great and fast.
    i use to have windows 7 and itunes never skipped a beat.
    i have a sony viao with an upgraded ram and ssd hdd.
    and its pretty fast.
    so i dont think its my computer and windows 8 seems to be fine.
    anyone else having this issue? but it only happens now and then.......
    NOTE:
    i have my music all copied to my sdd hdd aswell
    and thats all thats really on there as i have ext. hdd's.
    i have a average size library in itunes with around about 50gb of music.

    I had the same issues with Windows 8 Consumer Preview. I installed on a fresh system and still had issues.
    I experienced extreme lag, with pretty much everything, and iTunes freezing once I attempted to change the currently playing song.
    I had a mess with compatibility mode and found out that running it in with Compatibility mode enabled for Windows XP (Service Pack 3) and as an administrator fixed it. It works now, however, there is a popup message that comes up on launch telling you to change the compatibility settings, but pressing "OK" makes it go away.
    How?
    Open Windows Explorer, and navigate to: "C:\Program Files\iTunes" (For 32bit) or "C:\Program Files (x86)\iTunes" (For 64bit), unless you changed it.
    Right-click on "iTunes.exe", select "Properties" from the context menu, and click the "Compatibility" tab.
    Under "Compatibility mode" check off "Run this program in compatibility mode for:" and select "Windows XP (Service Pack 3)" from the drop down menu.
    Further down under "Privilege level" check off "Run this program as an administrator".
    Click "Apply" and "OK".
    Should fix any issues, I have my default iTunes Media Folder Location within an external hard drive so unplugging all of my USB's wasn't an option.
    Hope I helped!

  • Compatibilityy issue with windows XP and windows 8.1 for adobe photoshop elements 4.0

    Compatibility issue with windows XP and windows 8.1 for adobe photoshop elements 4.0?comcom

    You are going to have to contact Adobe on this one. We are other users.
    Sounds like it's not even an Apple question? Not sure.
    But the Adobe program changed, nothing changed in iTunes, right?

  • Major Issues with Windows XP and Sound Blaster Audig

    As mentioned in the post title, I'm using a Sound Blaster Audigy 4 card (recently purchased) and am having issues with Windows XP apparently because of it. When the card is physically installed, but the drivers are not, there are no problems. However, when the drivers are installed, Windows XP's "explorer.exe" crashes on boot, locking up the start menu and any other open windows. Now, I can manually end the explorer.exe application and then reboot it, and things will work... however, I cannot imagine that that is the intended functionality of this card. Additionally, I suspect the card in the failure of a game (Eve Online) but I would assume the issues are related. I've already narrowed the issue down to the Sound Blaster drivers. I've tried booting with the SB drivers but without the video card drivers, and the problem recurred. Every time I boot with the SB drivers installed, it fails. Without them, things seem to run normally. If it helps, I'm using an Intel Core 2 Duo E6400 processor, with GB of DDR800 RAM. I've installed Windows Service Pack 2 and all the other updates. The video card is a Geforce 7950 GT, with the latest NVidia Forceware (93.7) drivers. I've had this problem with both the Audigy drivers on the CD that came with the card and the newest ones downloaded from this website. My motherboard is a Gigabyte GA-965P-DS3, which includes onboard sound hardware, but I have disabled it at the BIOS level. I can provide dxdiag information or anything like that if necessary. Does anyone have any advice, suggestions, or have you encountered a similar problem?Message Edited by DerekKatz on 2-04-200603:2 AM

    Thanks for the helpful reply Dan
    I ran the file, CTZAPXX.exe, like suggested, and it ran without a problem. It installed the files and even required me to reboot my computer!!
    However, after a computer restart, I am still in the same boat. Codecs are installed, but the location of the device is "unknown". In Device manager, there are no unknown devices; it shows the codecs in the sound tab, but no actual hardware; as if my sound card does not exist.
    I use my computer for music, and my buddy needs me tomorrow night to play some music stored on my computer. I really do appreciate the help I am offered. I do not mean to sound impatient, but I really need this device fixed, or I will have to have him buy me a sound card....

  • Weird issue with Windows Server 2008 R2 Print Server

    I have an issue with Windows 2008 R2 (VMWare Hosted) running Windows Print Server. 
    Prior to a small network change, the print server was working well, hosting about 80 different networked printers from various vendors. 
    We made a change (that we ended up rolling back) to the Client's DHCP Scope OPT 006 (DNS Servers). The DNS servers never quite worked right and broke AD authentication to different servers, and was just a mess.
    After rolling back we are not able to keep the printers online. If we ping them from the print server, the printer(s) never wake up, when a print job is submitted. If we ping them from one of the access switches, they work fine (until they fall back asleep),
    to prevent this, if we start a ping on the server AFTER waking them up from the Switch Ping, they stay online and no problems. 
    If we stop the ping, they fall back asleep at some point, and again, won't wake up without intervention/switch side ping. 
    Has anyone experienced anything like this? Any tips on how I could possibly resolve it? 
    Thanks in advance.

    Hi,
    According to your description, the issue seems to be that the printers can't keep online. Sounds like a power managerment issue. Why these printers fall into sleep? Have you consulted this issue with the manufacturer of these printers? Do these printers
    fall into sleep if them lose the contact with printer server? Have you tried to reset the printers?
    >>We made a change (that we ended up rolling back) to the Client's DHCP Scope OPT 006 (DNS Servers).
    DNS client will cache the recently queried records. If the DNS server has replied with a wrong records, communication issues will occur. To clear the DNS cache on a Windows device, please run the command below:
    ipconfig /flushdns
    Best Regards.
    Steven Lee Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

  • Itunes issues with Windows having to do with Apple's patent

    I had a thought and am not sure if it's right. I was wondering if myissues with Apple Itunes store on Windows 7 has anything to do with the Patent laws and all with Apple and samsung and all that.

    I had the same issues with Windows 8 Consumer Preview. I installed on a fresh system and still had issues.
    I experienced extreme lag, with pretty much everything, and iTunes freezing once I attempted to change the currently playing song.
    I had a mess with compatibility mode and found out that running it in with Compatibility mode enabled for Windows XP (Service Pack 3) and as an administrator fixed it. It works now, however, there is a popup message that comes up on launch telling you to change the compatibility settings, but pressing "OK" makes it go away.
    How?
    Open Windows Explorer, and navigate to: "C:\Program Files\iTunes" (For 32bit) or "C:\Program Files (x86)\iTunes" (For 64bit), unless you changed it.
    Right-click on "iTunes.exe", select "Properties" from the context menu, and click the "Compatibility" tab.
    Under "Compatibility mode" check off "Run this program in compatibility mode for:" and select "Windows XP (Service Pack 3)" from the drop down menu.
    Further down under "Privilege level" check off "Run this program as an administrator".
    Click "Apply" and "OK".
    Should fix any issues, I have my default iTunes Media Folder Location within an external hard drive so unplugging all of my USB's wasn't an option.
    Hope I helped!

  • Qualcomm Mobile Broadband Gobi2000 compatibility issue with Windows 8 and above

    I am facing Qualcomm Mobile Broadband Gobi2000 competibility issue with Windows. Previously, after installing windows 8, I faced a problem of random shut down. But, after running registry and malware scan, it's now almost settled . But, my Broadband modem randomly stops working , and Windows Action Centre points it out as "USB Modem Qualcomm Mobile Broadband Gobi2000 is not competible with current version of Windows". It further suggest to contact HP for resolving the issue.

    I have called HP-Support and the answer was:
    «Thank you for contacting HP Active Chat Support.
    This is in continuation to our response with regards to your chat ID: 63381567
    As for the case logged in for compatibility issues after upgrading to windows 8.1, kindly try the steps below and see if that helps.
    Start the computer.
    Press the F10 key to enter the BIOS setup.
    Select Restore Defaults .
    Under Load Defaults , select Yes .
    Choose Save Changes and Exit .
    Under Save Changes and Exit , choose Yes .
    If Microsoft Windows does not recognize the external USB WWAN modem module, try the steps below:
    The Telephony Service has been disabled. Follow these steps to enable the Telephony Service:
    Open Control Panel .
    Expand View by: and select Large Icons .
    Click Administrative Tools .
    Double-click Services .
    Double-click Telephony .
    Under the General tab, expand Startup Type , then select Automatic .
    Click Apply , click Start , then click OK .
    Restart the system.
    If the issue still remains the same, kindly contact Microsoft or we would request you to be patient while we have more drivers available on the HP website.»
    The issue was not resolved.
    So I'm waiting for the release of the new driver...

  • Is there a known issue with windows 8 supporting itunes?

    each time I update itunes I lose my itunes store connection and therefore can't update apps etc. Is this a known issue with windows 8 users?

    Yes. Some are complaining.
    Search iTunes.exe. RIght Click, Properties, Compatibility, Click Run this program as Adminitrator. OK.
    See if this helps

  • Where is the forum for Windows Update issues with Windows 10 TP 9926

    Trying to find a fix to the Windows Update issue with Windows 10 TP 9926 build and can't find the correct forum to post this question?
    This will impact receiving the new build upgrades and will impact test strategy for the new supported OS in our desktop application.

    Might try them over here.
    http://answers.microsoft.com/en-us/insider/forum/insider_wintp-insider_update?sort=lastreplydate&dir=desc&tab=Threads&status=&mod=&modAge=&advFil=&postedAfter=&postedBefore=&threadType=All&tm=1427037339534
    Regards, Dave Patrick ....
    Microsoft Certified Professional
    Microsoft MVP [Windows]
    Disclaimer: This posting is provided "AS IS" with no warranties or guarantees , and confers no rights.

  • URL issue with Windows 7 Internet Explorer 11 and SAP NW PI 7.

    Hello SAP community,
    I am facing a strange issue with Windows 7 - Internet Explorer 11 and SAP NW java services (I hope I am in the correct discussion) ...
    When I try to open URL http://sapserver.hosters-name:port it is working so far with Windows 7 and Internet Explorer 11.
    But when I click than on NWA (example), I am getting "http 500 server error".
    I don't have the issue, when I start-up a VMware Workstation with Windows XP and Internet Explorer 8.
    But now the strange part: In our network DNS (Domain Name Service), we can also open the URL by http://sapserver.our-dns:port.
    Than it is working without problems with Windows 7 and Internet Explorer.
    I would agree to state the comment - it is just a Windows 7/Internet Explorer 11 issue, if it wouldn't work for both URLs (http://sapserver.hosters-name:port = problem URL; http://sapserver.our-dsn:port = working).
    We are using a SAP NW PI 7.x system. Some URLs for PI are using http://sapserver.hosters-name:port/java service.
    Do you have any hints what is cause the issue - I suspect some with Internet Explorer and Firefox (because with Google Chrome at least the URL for NWA is opened, beside the issue, Google Chrome can't display NWA content)?
    Thanks for your help.
    Best regards
    Carlos

    Hi all,
    I think I found the solution.
    The reason seems to be, the domain name for http://sapserver.our-dns:port, "our-dns" was already added to the compatibility view settings of Microsoft Internet Explorer.
    That seemed to be the reason, why it was working with http://sapserver.our-dns:port.
    When I now added for http://sapserver.hosters-name:port the domain "hosters-name" to the compatibility view settings it is now working.
    Internet Explorer Options => Settings for compatibility view => Add domain
    Best regards
    Carlos

  • When will there be an itunes update that resolves the compatibility issues with windows 8

    When will there be an itunes update that resolves the compatibility issues with windows 8

    I hadn't heard there are issues.  Can you tell me what the issues you have run into are?  I just downloaded it yesterday on my new laptop and I am having issues syncing today...

  • SSLVPN connectivity issue with Windows 7 x64 All browsers.

    I think that I have tried everything to get this working but whatever I seem to do I cannot connect to my SSLVPN using Windows 7 x64. The 32bit version is fine. I have installed the Microsoft C++ Redistributable 2010 and 2005 for both x86 and x64. I have tried clearing the cache in the Browser. I have installed Chrome and Firefox , I even started my laptop using the 'Disable Driver Signature Enforcement' from Advanced Boot options but nothing is working.
    Does anyone have anything else to try. This is a bit of a showstopper for us because not do we have this issue with Windows but we have Mac users as well and that is also an issue.
    Cisco really needs to fix this issue fast...
    Please help.
    Thanks
    Mark Sheehan

    Try using both the 32-bit and 64-bit versions of Internet Explorer.  Sometimes one of the two will work.

  • Windows 8.1 RDP Issues with Windows Server 2008 Standard.

    I have an issue maintaining an RDP connection from 64-bit windows 8.1 (standard and pro) to 32-bit Windows Server 2008 Standard.  Initial connection is normal, and as long as I am constantly typing on the link, for the most part it stays up. However
    if I do not keep typing, or go to another desktop program for a few minutes, and then go back, the following happens:
    If I am typing into notepad (or some screen that does not require windows to be refreshed) I can continue to do so, so the connection has not been lost, however if I try to do something that requires more extensive exchange of information (like file
    - open, or even trying to pull up the start menu), the connection pauses with about half the screen refreshed, sometimes after about 30 seconds a bit more of the screen fills out, but otherwise the connection is not responsive. Then after about 2 minutes,
    RDP reconnects, at which point I am back to "normal".  I have conducted some tests and made inquiries of others attempting to connect to the server.
    1) I can connect to other Windows (servers 2008 R2 and 2012)  with no connection issues from this PC
    2) I can connect to the 32-bit server with no issues using Windows Vista Ultimate and Windows 7 from the same location as the WIndows 8.1 PC
    3) When I do a network speed test while having these issues I see full download and upload speeds, so I am not experiencing intermittent internet issues.
    4) No-one else from other locations (not of course using Windows 8.1) has any issues using RDP to the 32-bit Windows Server Standard.
    These various tests seem to eliminate my network connection, and other operating systems, from the equation, and point to RDP issues on windows 8.1 connecting to the older OS.  I noticed in the September updates, a case 2989039 which seemed to point
    to similar issues when using UDP through Remote Desktop Gateway.  That update is on my machine, and my connection has the setting Automatically detect RD Access Gateway server settings.
    Any thoughts anyone?

    Hi  RonaldRenaud,
    If my understanding is right, this RDP issue only occur in the connection between Windows 8.1 and Server 2008.
    Please check if you have installed the update kb2984006.
    To resolve this issue caused by update 2989039, install update rollup 2984006. For more information, please refer to the following KB.
    http://support2.microsoft.com/kb/2989039/en-us
    Best regards,
    Fangzhou CHEN
    Fangzhou CHEN
    TechNet Community Support

  • Clone hdd with windows 8 to ssd

    HI, I've purchased a hp envy phoenix h8-1580d with windows 8 pre-installed on 25 july. Since then I've tried many ways to clone the system disk to an INTEL 330 120gb SSD but failed. At last, I decided to clean install the windows 7 Pro to the SSD, but the computer could not boot from the DVD, FAILED AGAIN. I would be very grateful if any expert here could provide any solution to solve this issue. My sincere thank in advance.
    Anyway, I did contact the hp technical support and they took 2 days to work out a solution and they failed too.

    Finally suceeded in cloning the HDD to SSD with EaseUS Todo Backup Free 6.0.

  • IPhone 4S - Wi-Fi Speed issues with Linksys 4500

    I have a Linksys 4500 and have extremely slow wifi speeds.  I've changed every setting, channel and anything else that was editable.  However, I can never get very good download speeds (typically below 1Mbs) but the strange thing is that uploads are usually around 5Mbs.  I finally tried a Ruckus 7363 AP and I consistently get close to 20Mbs so I know it is the wi-fi with the linksys router.  Has anyone else had the same experience and did you find a fix?  Again, I've tried everything and the problem only appears on ios devices.  Macbook has no issues nor does my android devices.  thanks

    I'm having the same issue.  My old iPhone 4 and the iPad 2 both connect seamlessly to iTunes (on WIndows 7), but the iPhone 4S doesn't sync automatically when plugged in to power.  Also it doesn't maintain a connection to iTunes over wifi.  For instance, right now iTunes isn't showing the iPhone 4S (but is showing the iPhone 4 and iPad 2) even though the iPhone 4S is on the same network, and is even connected to power.
    When I try to sync from iTunes (when the phone shows up) or from the iPhone 4S, it fails saying that it failed to start the sync process.
    Since the process works with the iPhone 4 and iPad 2, I'm assuming there must be some issue with the 4S, or another setting somewhere that isn't completely obvious.
    Any assistance is greatly appreciated.

Maybe you are looking for