Speed up load to ftp server in window server 2008 slow
Dear all.
I have configure FTP in window server 2008 (IIS 7.5...), when I test in LAN speed upload to ftp server is slow ( 60-80 KB/S).
Please help me fix it.
Thanks so much
you should post on IIS forum:
http://forums.iis.net/t/1187778.aspx?Maximum+file+size+for+FTP
http://forums.iis.net/p/1193472/2036340.aspx?Restrict+FTP+upload+file+sizes
try disabling firewall on the ftp server just check if it will help.
Every second counts..make use of it. Disclaimer: This posting is provided AS IS with no warranties or guarantees and confers no rights.
Similar Messages
-
Could not able to execute FTP commands in windows server machines 2012/ windows server 2008.
From windows server 2012 and windows server 2008, Opened port 20,21,22 in firewall bidirectionally. After Establishing connection by passing credentials 230 log in successful.
ftp commands executing getting as " 425 Use Port or PASV first" , "500 Illegal PORT command".
But I could able to do windows client machines like windows 7 and windows 8 with same environment
Note : Firewall ports are opened. have tested by making firewall down to avoid filters.
Pandiyan MuthuramanHi Pandiyan Muthuraman,
Did you mean even you disable or open the related port the FTP issue still exist? I found this errors most time occur when we use the ISA firewall and the FTP configured passive
mode, if you have ISA firewall please refer the following KB to fix this issue.
How to enable passive CERN FTP connections through ISA Server 2000, 2004, or 2006
http://support.microsoft.com/kb/300641
The have a specific form for the IIS question, if you have the further IIS related question you can ask in IIS forum.
IIS support forum
http://forums.iis.net/
Thanks for your understanding and support
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place. -
Error Installing InDesign CS3 Server on Windows Server 2008 R2 64BIT
Hello there-
I'm trying to install InDesign CS3 Server on Windows Server 2008 R2 64BIT (x64) Edition, however, we get a failure indication on the installer. Before, we have installed it properly on Windows Server 2008 R2 32BIT (x32) but some how we cannot proceed on a x64 box.
Is there any limitation on this sense? Any documentation about it?
Thanks and appreciate your answers.
Regards,
Gustavo Ortega
Software EngineerHello,
Have you followed these recommendations from the installation guide ( Installation Guide u2013 SAP Content Server on Windows 2008 ) :
Note: In the IIS 7.0/7.5, all the roles are not selected during the installation by default,
Please make sure all the below roles are included and IIS 7.0/7.5 is installed.
Roles needed in IIS 7.0/IIS 7.5.
Common HTTP Features
Static Content
Default Document
Directory Browsing
HTTP Errors
HTTP Redirection
Application Development
ISAPI Extensions
ISAPI Filters
Health and Diagnostics
HTTP Logging
Logging Tools
Request Monitor
Tracing
Custom Logging
ODBC Logging
Security
Basic Authentication
Windows Authentication
Request Filtering
Note : Anonymous Authentication should be enabled.
Performance
Static content Compression
Dynamic Content Compression
Management Tools
IIS Management Console
IIS Management Scripts and Tools
Management Service
IIS 6 Management Compatibility
IIS 6 Metabase compatibility
IIS 6 WMI Compatibility
IIS 6 Scripting Tools
IIS 6 Management Console
Note: There is a File Upload limitation in IIS 7 on Windows 2008 Server, IIS will reject any file that is
larger than 30 MB. This is a default limitation of IIS. You can increase the maximum file size by
setting the parameter maxAllowedContentLength in the file ApplicationHost.config.
The following command can be used to set the parameter from the command prompt, please
change the directory to Windows\System32\inetserv and then execute the command.
appcmd setconfig /section:requestFiltering/requestLimits.maxAllowedContentLength:150000000
The value is only an example, in this case the upload limit is set to 150MB.Server has to be restarted
after execution of this command.
Also, are you using Maxdb to store the files or is it a "flat files" content server ?
HTH.
Steve. -
Problem instaliing sun one LDAP server on windows server 2008 r2
Hi all ,
I am trying to install Ldap server (Sun ONE Directory Server) on windows server 2008
I am using apache-tomcat-7.0.28 and java jdk1.7.0_05
I am following this manual for installing :
https://blogs.oracle.com/marginNotes/entry/installing_directory_server_enterprise_edition1
I have a problem with the cacao agent and how to install it .
I've got this error message :
c:\Program Files\Sun\dsee7\bin>dsccsetup cacao-reg
Configuring Cacao...
## Failed to run "c:/Program Files/Sun/dsee7/ext/cacao_2/bin/cacaoadm.bat" set-
aram "jdmk-home=c:/Program Files/Sun/dsee7/lib/private"
#### Cannot create service for instance: [cacao.instance.name].
#### Cannot perform firstime inialisation and configuration.
## Exit code is 1
Failed to configure Cacao.
I stuck and with no other solutions . I hope if you could to help with this issue .
i will glad to know if there is any other ways to install this specific Ldap server ,
Thanks,
AlonYou most likely skipped the step of starting the installed server prior to trying to access admin URL. Please check this document:
http://docs.sun.com/source/817-1830-10/win.html
Relevant section is:
You can start the Administration Server in either of the following ways:
# Select Start Menu -> Programs -> Sun ONE Web Server, and choose Start Web Server Administration Server.
# From the Control Panel�s Services item.
HTH... -
Backup Windows Server on Windows Server 2012
We install backup windows server on windows server 2012 standard, more when I go in tools to be able to manage it he is not there, try the Wbadmin.msc command, and returns me a message that Windows can not find the Wbadmim.msc . Have uninstalled and reinstalled
feature several times and still nothing.
I am new to the forum, so descupem me if there is another topic like this.Hi There,
Have you tried to search for "Administrative Tools" and run the "Windows Server Backup" from there?
Good Luck -
Urgent help needed to setup Forms 6i Server on Windows Server 2003
Hello,
I am trying to install Forms 6i Server from the Forms/Reports 6i Release 2 CD onto a server with Windows Server 2003 Standard Editon (services pack 1) installed.
The Oracle Installer produced the following error when I tried to install the Forms 6i Server From the Forms/Reports 6i Release 2 CD:
user1.pin(20); os_error while spawning ifsrv60 -install forms60server port=9000 mode=socket batch=yes.
Has anyone successfully installed Forms 6i Server from Forms/Reports 6i Release 2 CD onto a Windows Server 2003 server?
Any help is appreciated.
PhilYou it obtained to install the FORMS 6i SERVER in Windows 2003 ?
I am with the same problem and not yet I obtained solution. -
Installing Sun Directory Server on Windows Server 2008
Has anyone tried installing Sun Java System Directory Server in Windows Server 2008? I am trying to do this but get an error stating that nss3.dll is missing at configuration time.
Windows 2008 is not a supported platform for any DSEE release. Even if you get it working, Sun Support won't be able to help if you have issues.
This issue seems to have been reported on Windows 2000 with DSEE 6.0 too and one workaround is to remove the nss3.dll from c:\winnt\system32 or equivalent directory. Please note this workaround is not targeted at Windows 2008, so use at your own risk.
http://sunsolve.sun.com/search/document.do?assetkey=1-1-6680728-1
Winodws Native DS6.0/ISW6.0 Zip:error could not locate nss3.dll
Edited by: etst123 on Jan 29, 2009 10:39 AM
(added link to bug report) -
I am unable to create pdf using adobe printer to a redirected folder on a server running windows server 2003
In the app-server-ant.xml file, as indiacted in the error message i am getting, at line 145 it is suppose to get the path to \bin\asadmin.bat from the value of a paramater called 'asadmin'. This value is being set in the beginning of the file.
The parameter value of 'asadmin' is further referring to value of another parameter called 'javaee.home' which is being set in tut-install/javaeetutorial5/examples/bp-project/build.properties
I have checked the values of both these parameters and they are set correctly, so since it is still giving me problems, at line 145 i hard coded the path instead of the parameter name:
I replaced line
<exec executable="${asadmin}" failonerror="${failonerror}" dir="${javaee.home}">
with
<exec executable="c:/sun/appserver/bin/asadmin.bat" failonerror="${failonerror}" dir="${javaee.home}">
This works. -
Problem In Data Base Creation... Oracle 10g server in windows server 2008
I have installed Oracle 10g server in windows server 2008 and the domain & active directory r created now i am trying to create the databse i am getting usual error (tns protocol adapter error ) in the 2% i have removed the domain and the active directory from windows then i created but this is not a solutions i need to create the data base in the domain server...
this is a forms forum.
please post in Database Installation -
Error when configuring Siebel Server in Windows server 2003
Hi
I am getting below error when configuring Siebel server in Windows server 2003 VM. All the ODBC connections and SADMIN user id & password and gateway host name and port everything correct. Able to ping and telnet to gateway port 2320. Please help on how to overcome this situation....
2021 2012-03-08 01:13:22 0000-00-00 00:00:00 -0500 00000000 001 003f 0001 09 sw_cfg_util 3940 3332 C:\sba81\siebsrvr\log\sw_cfg_util.log 8.1.1 SIA [21111] ENU
GenericLog GenericError 1 000000024f580f64:0 2012-03-08 01:13:22 Error in transferring input values ,num of arrays incorrect 0, expected : 1
GenericLog GenericError 1 000000024f580f64:0 2012-03-08 01:13:22 TransferInputsToValues returned error:3611539 to SetControlValues
GenericLog GenericError 1 000000024f58096c:0 2012-03-08 01:13:33 NSS - ErrCode 4597527 SysErr 0
GenericLog GenericError 1 000000034f58096c:0 2012-03-08 01:13:35 NSS - ErrCode 4597527 SysErr 0
GenericLog GenericError 1 000000034f58096c:0 2012-03-08 01:13:35 Validation failed : C028: Unable to connect to the Siebel Gateway Name Server ῤ粃䂬粃呸 ֓呸 ֓㷕粃Ꞡ粈㶻粃
GenericLog GenericError 1 000000034f58096c:0 2012-03-08 01:13:35 ValidateFailed for Gateway Name Server TCP/IP Port, error : C028: Unable to connect to the Siebel Gateway Name Server ῤ粃䂬粃呸 ֓呸 ֓㷕粃Ꞡ粈㶻粃Please check Doc ID 1391312.1 on support.oracle.com, this article has a list of possible causes and resolutions for the error messages you are receiving.
Hope it helps,
Wilson -
Windows server 2012 as primary DC and DNS server and windows server 2003 as secondary DC and DNS
Migration from windows server 2003 AD DC and DNS server to windows server 2012 R2,
Cannot I set up Windows server 2012 R2 as primary DC and DNS , windows server 2003 as secondary DC and DNS ? (for backup server when server 2012 fail, user can continue to login and access internet services)You can mix both as long as your Forest and Domain Functional level are Windows Server 2003. However, I would like to bring your attention to this blog about known problems when mixing DCs with Windows Server 2003 and 2012 R2 OS:
http://blogs.technet.com/b/askds/archive/2014/07/23/it-turns-out-that-weird-things-can-happen-when-you-mix-windows-server-2003-and-windows-server-2012-r2-domain-controllers.aspx
This posting is provided AS IS with no warranties or guarantees , and confers no rights.
Ahmed MALEK
My Website Link
My Linkedin Profile
My MVP Profile -
How to Migrate windows 2008r2 RDS server to Windows server 2012r2 RDS
Hi, I want to migrate our 2008r2 RD server + Cals to windows server 2012r2 server, the user will still connect to 2008r2 server but the server hosting the license will be migrated to a 2012r2 server. Currently I have 2 servers that users can connect
to that are served by the 2008r2 RDS (the server I'm converting is just hosting the license) the server user connect to point to this license server. How do I proceed to migrate, I'm searching for documentation but I can't find much, I found that I can only
convert to 2012r2 from 2012 or better OS, so I installing a temporary 2012 server to do a double migration seem to be the best course of action but I can't find any documentation on how to Migrate the Remote Desktop Services Role Services from 2008r2 to Windows
Server 2012.
Also I just discovered that this server is also hosting license for windows server 2003 terminal service. Will I be able to host these licences on 2012R2 ?
Any pointer would be appreciated.Hi,
It seems like migration the Remote Desktop Services Role Services from 2008r2 to Windows Server 2012 is not supported.
http://technet.microsoft.com/library/dn479239.aspx
So i think you may install and configure the RDS server on Windows Server 2012 and then migration to Windows Server 2012r2.
Hope this helps.
Regards.
Vivian Wang -
Integrate On-Premises Exchange Server With Windows Server Essentials
I have Exchange Server 2013 installed on Win Server 2012 R2 joined to Windows Server Essentials domain. Attempting to integrate the Exchange Server into the Essentials domain from the Essentials Dashboard using the wizard fails with the error, "Cannot
locate an Exchange Server on the network. Make sure that your Exchange Server is setup and that it is connected to the network". I can communicate with the server in multiple ways from the Essentials Server and other computers on the domain. Mail
flow in and out of the Exchange Server works without issue. I can use the various management tools to administer the Exchange Server. The only task I cannot complete is integrating it into the Essentials environment which I need to do to move on
to creating user mailboxes for user accounts setup in AD.
All research to date has come up empty handed.
Help!Hi RSUL,
Any update?
On current situation, would you please let me confirm something more? It may help me to understand this issue
clearly.
Would you please let me know how join the Windows Server 2012 R2 (which had been installed Exchange Server 2013) to Windows Server Essentials domain? Did use Connector software
(type http://servername/connect)?
On server essentials, please open Dashboard and navigate to DEVICES. Then check the Status of this server which had been installed Exchange Server 2013.
Currently, the Services Integration features, including on-premises Exchange integration, are only supported in a single domain controller environment. Meanwhile, the integration
wizard must be run on a domain controller.
In addition, please refer to the following article and check if can help you.
On
Premises Exchange Integration Windows Server 2012 Essentials
Integrate an On-Premises Exchange Server
with Windows Server Essentials
By the way, please check Event Viewer and some relevant logs if you can find some more clues.
Hope this helps.
Best regards,
Justin Gu -
Unable to load ADFS 2.0 in Windows Server 2.0
I am trying to federate a domain in Office 365. The AD FS servers are running Windows 2012 R2 and AD FS appears to be working properly. The errors I receive are shown below.
PS C:\Windows\system32> import-module msonline
PS C:\Windows\system32> Connect-MsolService [credentials entered]
PS C:\Windows\system32> get-msoldomain
Name
Status Authentication
contoso.com
Verified Managed
adatum.com
Verified Managed
fabrikam.com
Verified Managed
PS C:\Windows\system32> Convert-MsolDomainToFederated -domainname contoso.com
Convert-MsolDomainToFederated : Failed to connect to Active Directory Federation Services 2.0 on the local machine.
Please try running Set-MsolADFSContext before running this command again.
At line:1 char:1
+ Convert-MsolDomainToFederated -domainname contoso.com
+ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ CategoryInfo : InvalidOperation: (:) [Convert-MsolDomainToFederated], FederationException
+ FullyQualifiedErrorId : InvalidCommandSequenceGeneva,Microsoft.Online.Identity.Federation.Powershell.ConvertDoma
inToFederated
PS C:\Windows\system32> Set-MsolADFSContext -Computer ADFS01
Set-MsolADFSContext : Unable to load the Active Directory Federation Services 2.0 snap-in for Windows PowerShell.
At line:1 char:1
+ Set-MsolADFSContext -Computer ADFS01
+ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ CategoryInfo : InvalidOperation: (:) [Set-MsolADFSContext], FederationException
+ FullyQualifiedErrorId : SnapInLoadFailed,Microsoft.Online.Identity.Federation.Powershell.ContextCredentialsComma
nd
I've not had this problem before when using Server 2008 R2. What do I have to do to the AD FS server to make this work?
Ed Crowley MVP "There are seldom good technological solutions to behavioral problems."I'm going to answer my own question. The following registry key and values were present. There are blog and forum posts suggesting that this needs to be added, but they only apply to Windows Server 2012, not Windows 2012 R2. Further, this
registry key and values were present on my servers even though I did not add them manually.
Removing this key, which removes the values underneath, solved my problem.
Windows Registry Editor Version 5.00
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\PowerShell\1\PowerShellSnapIns]
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\PowerShell\1\PowerShellSnapIns\Microsoft.Adfs.PowerShell]
"ApplicationBase"="C:\\Windows\\ADFS"
"Version"="6.2.0.0"
"AssemblyName"="Microsoft.IdentityServer.PowerShell, Version=6.2.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35"
"Description"="This powershell snap-in contains cmdlets used to manage Microsoft Identity Server resources."
"PowerShellVersion"="1.0"
"ModuleName"="C:\\Windows\\ADFS\\Microsoft.IdentityServer.PowerShell.dll"
"Vendor"="Microsoft"
Ed Crowley MVP "There are seldom good technological solutions to behavioral problems." -
Hi team,
i m trying to ftp a file on one of the windows server via Publisher.But i get this error.
oracle.apps.xdo.servlet.scheduler.ProcessingException: java.lang.StringIndexOutOfBoundsException
at oracle.apps.xdo.servlet.scheduler.XDOJob.deliver(XDOJob.java:1621)
at oracle.apps.xdo.servlet.scheduler.XDOJob.execute(XDOJob.java:478)
at org.quartz.core.JobRunShell.run(JobRunShell.java:195)
at org.quartz.simpl.SimpleThreadPool$WorkerThread.run(SimpleThreadPool.java:520)
Caused by: java.lang.StringIndexOutOfBoundsException
at java.lang.String.substring(String.java:1088)
at oracle.apps.xdo.servlet.scheduler.XDOJob.deliver(XDOJob.java:1431)
... 3 more
Can you please help me out with this?I would call my hosting company, especially if that company happens to be GoDaddy.
This is a very common occurence with that particular hosting provider.
Maybe you are looking for
-
Bad performance on Factory.parse method
Hi all, I have some classes created from an XML Schema. I'm using them to load an XML from disk instead of using SAX or DOM. The problem is that I have monitorized the performance with OptimizeIt and every time I call the XXXXType.Factory.Parse(Input
-
OIM 11g R1 - Rule does not work
Hello, i want to add all users to a specified role "abc", if they are member of organization "xyz" I created a rule in Design Console: Type: General Element: Organization Name == xyz I added this rule to the role "abc", but the members will not be ad
-
ISSUE: 1 Partner Functionality - After entering a line item in PO, PI partner disappers and needs to be re-entered again. Account Group Z001 using VN and PI partners. This is the purchasing vendor. If Accounting needs to have a different Remit T
-
Hi, There is a requirement where we want to run manual Ad-Hoc BOP by sales order,creation date range,material and plant so that it will pick only the particular selected orders. But we found that though it picked particular sales order but it filter
-
Why is my iTunes app blocked?
I try to run it but it just doesn't. It only appears a box " iTunes is blocked, might by you have not permission to use it" or something, but it it my Mac, so.. thank you (: