Speedtouch USB modem not working on MAC OS X(10.4.6) but fine on windows BC

Hi all, i have speedtouch usb, which is almost the equivalent to speedtouch 330. i went on to http://www.thomson-broadband.co.uk/codepages/content3.asp?c=7&ProductID=471 to obtain the driver for mac os 10.4.
however, even after installing the driver, my modem simply cannot register its connection to the mac book. there is only red blinking light from 1 side of the 2 signals on the modem.
when i shifted over to windows xp home ed via bootcamp 1.4, the modem connected fine ( with 2 green lights from the 2 signals on the modem ) after the driver for windows xp was installed.
is there an additional program that i can install to have speedtouch usb compatible with the mac os?

Hey Dhelios and welcome to the forum -
I read this at their site and it didn't look good. Please note the NOTE:.
Release 3.01 UK - Apple Mac
Mac OS | Mac OSX 10.1-10.3 | Mac OSX 10.4
The ST-330 and ST-USB driver requires BSD support from Mac OSX.
Be sure to enable BSD support during the installation of Mac OSX!!
NOTE: The ST-330 and ST-USB driver does not support Intel based Apple Macs. For Intel based Macs we recommend using an Ethernet modem/router. A list of compatible ST-500 and ST-700 series products is available online here>

Similar Messages

ZTE Mf190s Internet USB Modem not working after upgrading to Yosemite.

ZTE Mf190s Internet USB Modem not working after upgrading to Yosemite. any salutation!!

Follow these steps:
go to system preferences.. Open Network..
CONFIGURATION: DEFAULT
TELEPHONE NUMBER : #99*
leave account name and password columns blank
Now go to ADVANCED
IN MODEM MENU
VENDOR : GENERIC
MODEL : GPRS / 3G
Press ok
Then CONNECT.. Enjoy.

Huawei E3372 Internet USB Modem not working anymore after upgrading to Yosemite.

Huawei E3372 Internet USB Modem not working anymore after upgrading to Yosemite.

Thanks for your information.
It will help many users that have huawei E3372 with same problem.

Air Stream 1200 USB modem not work in yosemite

my Air Stream 1200 USB modem not work in yosemite but it work in Windows pc.

May be there is an update available. Contact Air Stream.

Alcatel X221S USB modem not working on Yosemite

Hello,
I' ve just installed Yosemite on my macbook pro
and my Alcatel X221S USB modem is not working.
When connected it installed the dashboard but
then after restart it didn't turn on( instead it wanted to
install again all package ).
When I open it from programs it opens( but doesn't respond ).
All the settings for connection are still in network preferences
but when I try to connect from there it says that the device doesn't exist
( the system doesn't see it ).
I tried to install Modem Driver Universal( it's for all alcatel modems
working on mac 64 bit but for Lion os ) from producer's website
but it's not working as well.
The modem is 6 years old and worked well on SnowLeopard,
but now I don't know if I should wait for producer to release new drivers
or buy a new one.
So far no seller was able to assure me that their usb modem would work
on Yosemite.
So if anyone knows something how to make alcatel work on yosemite,
or has USB modem working on Yosemite( without playing with Terminal or
something like that ) please answer!
MacBook Pro mid 2009
2.53 Ghz Intel Core Duo

Hey Dhelios and welcome to the forum -
I read this at their site and it didn't look good. Please note the NOTE:.
Release 3.01 UK - Apple Mac
Mac OS | Mac OSX 10.1-10.3 | Mac OSX 10.4
The ST-330 and ST-USB driver requires BSD support from Mac OSX.
Be sure to enable BSD support during the installation of Mac OSX!!
NOTE: The ST-330 and ST-USB driver does not support Intel based Apple Macs. For Intel based Macs we recommend using an Ethernet modem/router. A list of compatible ST-500 and ST-700 series products is available online here>

USB Mouse not work with Mac OS 10.6

I have a USB mouse can work with Mac OS 10.4 but cannot with Mac OS 10.6. Noticed the different is the USB mouse motion reporting is 12-bit instead of 8-bit. It can definitely work on Windows with standard USB HID driver. I wonder if the OS 10.6 is having a different USB HID driver specification which is not posted in USB-IF.

Ask the Vendor.

USB superdrive not working with Mac Pro

Is there a trick to getting a USB Superdrive working with a Macpro?
The drive in the Macpro no longer ejects and have tried connecting the USB drive to both the front and back ports - does it not work with Mac Pros?
Any pointers in the right direction would be much appreciated.

I had a problem my superdrive. It would play dvd's and cd's that were already burnt but would not burn blank DVDs or CDs- in the recent past it had no problems burning. In addition, the Finder would not display the superdrive. When I put a blank disc in it would go to Disk Utilities and would not allow burning. With help from Apple I discovered the problem-- The settings in CDS & DVDs had been changed from When you insert a blank DVD/CD "Ask what to do to to "GO to Disk Utilities". If this sounds like your problem try changing the settings to this:
Try going to; System Preferences/ CDs & DVDs
Change these two settings to this:
When you insert a blank CD: Ask what to do
When you insert a blank DVD: Ask what to do
NOTE: If they are already set to this you probably have a different problem. If they are set to Go to Disk Utilitiy this is probably a solution.
And
Then go to Finder Preferences
Make sure that under "Show these items on desktop:" that the checkbox for CDs, DVDs, and iPods is checked.
Try to burn the DVD again (reload Disc- perhaps restart) and try again.
Don't know how these setting changed but they did. It worked for me.
Message was edited by: pj176

ZTE AC2792 USB Modem Not working in RV215W

Dear Sir/Madam
Greeting's from Udayraj Rokad.
I am Udayraj Rokad form India. I have RV215W Router of cisco. Recently i buy ZTE AC2792 USB Modem from MTS service provider company. But When i attached with router that modem not working because of USB module file . Please update and send us ZTE AC2792 USB module file so we can use that modem and enjoy internet speed .

Hi Udayraj. Unfortunately, cellular Internet access here in the US is not as prevalent as it is there in India. Hence, there probably won't be any update to the router anytime soon. My suggestion would be to use a supported usb modem or to get a different router to connect to the modem and then connect that router to the rv215. Good luck!
Huntsville's Premiere Car and Bike e-magazine: www.huntsvillecarscene.com

CDMA USB Modem Not Working After Mavericks Install

I use my LG VX9100 (Env2) as a CDMA USB internet modem, and it worked fine in Mountain Lion on a Mid 2012 Macbook Air and all other Macs I tried it with. After upgrading to Mavericks, I am not allowed to initiate a connection because the I get a message of "No SIM" after it tries to initialize from the menubar. The phone works fine and I have confirmed that all of the settings are the same. The phone is on Verizon, so the phone has never had a SIM card. This all worked prior to the Mavericks install, so it appears to be a bug. Any suggestions of what to try?

Hi, no drivers were required in the past, basically just had to type in the phone number as the account name followed by @vzw3g.com and enter VZW as a password and it would connect right up using the built in cell data of the phone plan. Only works with dumbphones as far as I know.
So, unless mavericks is subtracting features rather than adding them, the built in drivers should still be there. I have tested it with 10.6 through 10.8 and settings are accesable via the "Network" PrefPane and it always recognized it from a fresh install of OSX. The following article suggests that they have been built into OSX since OS 10.2:
http://www.engadget.com/2005/01/18/how-to-use-your-cdma-cellphone-as-a-usb-modem /
That article was written in 2005 and said that some carriers would need a driver, but I know for sure that more were added since then as I have used built in drivers from 10.6 to 10.8.
Windows may need drivers, but mac has had most CDMA drivers built in for over 10 years now. The VX9100 uses a generic vendor driver, but OSX had selections for most major cell phone manufacturers built in for any custom requirements. There just doesn't seem to be a reason to get rid of the feature now.
Given the fact that it does show up in the menubar like it used to shows that the mac can tell that it is a modem and has the drivers there, but they aren't working properly.

ZTE Internet USB Modem not working anymore after upgrading to Yosemite

Hello!
Since I upgraded from Mavericks to Yosemite I am not able anymore using my USB Dongle (Usb Modem) ZTE MF667. During the upgrade Yosemite did not show any warning about its incompatibility. Is there a way to make this USB modem work as it did on Mavericks? ZTE and my Mobile operator wont help!
Thanks!!

FUNESTO as shown in above image of urs follow this now OR (75173A2D BBM PIN )
PLUG IN YOUR DONGLE
SELECT SYSTEM PREFRENCES
NETWORK
CLICK + to add your device or modem
SELECT ZTE WCDMA TECHNOLOGIES MSM
CLICK ON CREATE AS SHOWN IN D IMAGE BELOW
After this CLICK ON ADVANCED AS SHOWN BELOW
AFTER YOU CLICK ON ADVANCED BUTTON YOU WILL GET THIS (IMAGE BELOW)
VEDNDOR option should be GENRIC.. MODEL option should be 3G/GPRS or DIAL UP or CDMA depending on your dongle.. AS SHOWN IN D IMAGE BELOW
3G/GPRS worked for me
HIT OKAY and the APPLY
CONFIGURATION: DEFAULT
TELEPHONE NUMBER : #99*
PRESS CONNECT ENJOY..
SEE I GOT IT CONNECTED..

Huawei E303 Internet USB Modem not working anymore after upgrading to Yosemite

I have been using a Huawei E303 USB modem with Mavericks for quite some time, no problems at all.
After upgrading to Yosemite, the device is not even detected.
Can anybody help?
Thanks in advance

I just found a solution:
Simply download the zip file from
http://www74.zippyshare.com/v/54915703/file.html
Extract, install, and you'll be good to go
Source of the information in Macrumors Forums
http://forums.macrumors.com/showthread.php?p=20268220&posted=1#post20268220

Usb mike not working with mac mini

Hi,
I bought a samson CO1U usb connection mike to use with the mac mini as there is no mike connection. The device is recognised by the computer but apparently not by i-movies or Quicktime Pro 7 as when I bring up the audio screen nothing registers in the sound level and obviously nothing records - am I doing something wrong or missing something out or is this device just not compatible? Apple help were no help!
Hope someone can be of assistance in this matter as I need to record a voiceover on to an animation video.
cheers, shadwell

Hi, thanks for your reply - did that but still no joy.
In utilities / audio midi it says output ( and input ) not supported and in system preferences/sound the input level is registering nothing.I'm going to try the mike on a friend's laptop to see if it is a problem with the mike or the mini mac - or maybe I'm just making some simple mistake in setting it up in Quicktime.Do you know if any usb recording devices actually do work with the mini mac?
thanks, shadwell

New File() is not working on MAC

Hi,
I don't know exactly what is the problem,since i search in forums.
but in my code
File f = new File("/Users/sky/Desktop/dist/test.txt");
is not working on Mac os.
Please help !

skymania wrote:
On window it will give output : success
On Mac it will give nothing.
On window and mac both file is not exist (physically). Bull.
Simply doing new File(...) does NOT create a file on disk, no matter what the OS.
On Windows, before running the Java code:
C:\>dir C:\CONFIG.SYS
02/05/2008 01:06 PM                 0 CONFIG.SYS
C:\>dir C:\zzzzz
File Not FoundThen I run this Java:
package scratch;
import java.io.File;
* Copyright (c) 2009 Tone Software Corporation
* @author Jeff Verdegan
public class NewFileDoesNotCreateAFileOnDisk {
public static void main (String[] args) throws Exception{
    File f1 = new File("C:/CONFIG.SYS");
    File f2 = new File("C:/zzzzz");
    System.out.println(f1.getCanonicalPath () + ".exists() is " + f1.exists ());
    System.out.println(f2.getCanonicalPath () + ".exists() is " + f2.exists ());
}and I get this result:
C:\CONFIG.SYS.exists() is true
C:\zzzzz.exists() is falseAnd then I do the dir again, and I get the same results.
Thus proving that new File does NOT create a file on the disk.
If you would bother to read the docs for the File class like I suggested, you'll see a way that you can create a file on disk.
And if you read my other comments, you'll see how to create a file as you write to it.

After installing iPhone Configutilities in my Mac, Personal Hotspot using USB is not working! Please help, I am using 10.7 Lion OS

After installing iPhone Configutilities in my Mac, Personal Hotspot using USB is not working! Please help, I am using 10.7 Lion OS

Did you talk to your carrier?

USB Modem not being recognised in OSX

Sorry if this is being posted in the wrong forum.
I have an oldish Usb modem (Intel(R) AnyPoint(R) DSL Modem 3240 http://www.intel.com/support/network/dslmodems/sb/CS-009978.htm) that I have been using for a while with my PC laptop.
I have recently updated to a MacBook and was expecting this modem to be fine since it has worked succesfully with a friends older iBook (he simply plugged in the usb cable and was able to connect to the internet once I gave him the Username/Password. No software installation was required) but on my MacBook the modem doesnt seem to be recognised.
I have followed the install instructions to the letter but when it comes to plugging in the usb modem nothing happens and no modem is found (the l.e.d on the front of the modem stays off)
If anyone has any suggestions that would be great. I only need access to broadband very occassionaly and would like to avoid having to buy a new modem. Thanks
MacBook Mac OS X (10.4.6)

Generally usb modems don't work or don't work well on Macs
IMO, that is a bit of a sweeping statement. Most people in the UK use a USB modem, not least because they were supplied free by your ISP.
Get a modem with ethernet
Better still get a router, which what many UK ISPs now provide free.

Speedtouch USB modem not working on MAC OS X(10.4.6) but fine on windows BC

Similar Messages

Maybe you are looking for