Spitting out blank discs, but theres a twist and it involves windows...

Here is my version, which is most like everyone else. However, it differs a bit. When I put in a blank cd it tries to read it three times and then ejects it. I set the preferences to ignore and it still dose the same thing. It reads cds and dvds fine but not blank ones. I have rebooted and all that, still nothing. This is where its different. I rebooted into windows boot camp and used nero and everything is fine, works like a champ. So what is the problem here? Why is that the great almighty mac needs windows os to burn a cd? Is it firmware or what? I use toast but toast has nothing to do with why my mac doesn't recognize a blank disc in the first place. Thanks in advance!
-LJ

Welcome to Apple Discussions
The Mac software does seem very sensitive to dust and dirt of the lens and it might be worth running a DVD Lens Cleaner through it to see if that makes any difference ...

Similar Messages

IDVD spits out my disc and stops

Help please. My iDVD will prepare, process menus, process slideshows, then process movies...just like it should. BUT, when it gets to the burn part. It spits out the disc and basically freezes there. I have been working with iDVD for over 5 years and have never had this problem, it has only happened (once) since I got my MacBook in July 2006. I am not sure if it is a problem with my MacBook, or if it is a problem with the Verbatim discs that I got to go with my external DL DVD burner. Please help...please?

Might get a few more replies and possible solutions if you start your own post. That way folks are more likely to reply to your own situation and it will likely draw the attention it deserves.
Nevertheless, the media of choice on iDVD6 forums is Verbatim followed by Maxell DVD-R. Either perform well in most macs. Use the search feature on this forum and you'll find Memorex as the least desireable choice due to higher than expected burn failure rates. This comes from experience.
A good third choice is FujiFilm DVD-R as well as Taiyo Yuden DVD Media or even RiData/Ritech DVD-R Dual Layer medias ....
Hope this helps. Good luck!

HP Laserjet 2600xi new drivers prints garbage spits out blanks

A friend called me about this problem and all I knew to do was to get the latest drivers and install them after removing all traces of old HP software. They're using an eMac with OS 10.4.11. The problem may have a simple solution. When they send a file to print, at first there is a page of 'garbage' printed followed by the printer just 'spitting out' blank sheets until they turn it off.
Any ideas to try? It could be a corrupt spool folder I suppose but don't know where to look for the file.
Thanks

Thanks, Greg. You are right that the 2600xi is Photosmart rather than Laserjet. I was just passing on the info given me by the owner who is frankly clueless. He asked my advice because I'm somewhat more experienced. I don't know how the rpinter was added to the Print & Fax pref pane.
As far as using the HP drivers I've gotten them to install new ones and had them look to see if the printer was recognized in the Printer Setup Utility.app. It was and that's the last time I talked to them. I may have to go and make a house call. Thanks for your information and advice. I'll get back with any update.

HP PSC 2175 spits out blank paper while I print.

I have Dell GX520 Desktop PC with Windows XP service pack 3 and HP PSC 2175 all-in-one printer. Since few days I m having trouble printing with my printer. When I try to print it simply picks up the paper scans it and spits out blank paper instead of printing it. There is no any error message or flashing light or any thing in the printer.
But still I can make copy or print the test page from it. The only thing is I can't print any document from WordPad or NotePad or through Adobe Reader. I don't have Office on my PC.
I have tried every thing that I can do. Uninstall the driver and reinstalled it downloading from HP website,updated the drivers manually, replaced new cartridges and what not. But I still have the problem. It would be so helpful if you have any solution to this problem.

I'm having the same problem....
The computer is a hp pavilion.
When trying to print, It loads the paper, It checks the paper position, then it just ejects the paper.
I opened the print job que and watched it.
When the print job ques up, it shows the job...then deletes the job before printing it.
It has been working fine up until a few days ago.
Any help would be appreciated.

Printer spits out blank pages v8.1.3

When I hit print button, my printer spits out blank pages
(about the same number as there are pages in the pdf document). The
printer works fine with other programs (Word, Excel etc.) but not
with the Acrobat 8.1.3
What gives?

Thank you for your posting. These forums are specific to the
Acrobat.com website and it's set of hosted services, and do not
cover the Acrobat family of desktop products. Please visit the
following forums for any questions related to the Acrobat family of
desktop products:
http://www.adobeforums.com/cgi-bin/webx/.3bbeda8b/

Remote Disc Can't recognize Blank disc, but it does recognize other discs. I am trying to burn something from my itunes on my mac mini to a blank disc on my windows computer. What could be wrong?

Remote Disc Can't recognize Blank disc, but it does recognize other discs. I am trying to burn something from my itunes on my mac mini to a blank disc on my windows computer. What could be wrong?
I can see other discs such as music and stuff so I know I have installed it correctly but how come I can't see the blank disc that I need to burn?

You can't burn discs remotely, you can only read data discs remotely (i.e. you cannot play movie DVDs either).
Either copy the files to the remote computer or get an external drive.

Hi, I lost my serial number for PS Elements11 following computer crash. Os is W7. I have the cd installation disc but there is no serial number with it or in the envelope .. How can I obtain the serial number please? Thanks

I lost my seriel number for PS Elements 11 following computer crash. Os is W7
Peter Jones Aug 27, 2014 5:36 AM
Hi,
I lost my serial number for PS Elements 11 following computer crash. Os is W7. I have the cd installation disc but there is no serial number with it or in the envelope
How can I obtain the serial number please?
Thanks

If you registered the software you should be able to find the serial number thru your Adobe account online.
To locate the serial number:
http://helpx.adobe.com/x-productkb/global/find-serial-number.html

Hi icant sync my photos from itunes to iphone ..it shows copying 1 out of something but afterwards it stops and no photos in iphone ..i formatted several times ..and from my utunes i have sync my brothers iphone it synced prefectly only its problm of my p

hi icant sync my photos from itunes to iphone ..it shows copying 1 out of something but afterwards it stops and no photos in iphone ..i formatted several times ..and from my utunes i have sync my brothers iphone it synced prefectly only its problm of my iphone .......i have also deleted the ipod photo cache but still the same

can any 1 help me

My PowerMac G5 will not read my Leopard disc, dual layer dvd, how do I force boot from UBS DVD drive to install?? Or is there another way. It just keeps spitting out the disc!!

I have a power mac G5. Ir originally had Tiger on it. When I reinstalled for some odd reason the disc decided to install Panther, no clue why!! Either way I got a hold of a Leopard disc for this computer. It is apple certified and bought from Amazon and works for this computer.
Hoever, for some odd reason it keeps spitting it out. Discs under 4.7 GB is reads fine but the bigger discs it wont seem to read. What I need is to know how to get, or force, it to boot from an extrenal dvd drive. Or any other methods to get it to install.

I do not believe you can "Upgrade" directly from the "Panther" installed on your computer to "Leopard". You have to have at least "Tiger" installed already Before you can install Leopard. Thus your Mac is not recognizing the Leopard Install disk.

My HP PSC 2175 printer spits out blank paper while I try to print.

I have Windows XP service pack 3. My printer(HP PSC 2175 All-in-one) use to work well until few days before. I leave the printer unused for few days and now when I came back to use it , it simply picks up paper scans( a ledger like light runs to and fro at the top end of paper) and spits the paper out.This only happens when I try to print. I can still make black copies well from the same machine. I only have Note pad and Word Pad. It does the same with both. I tried with pdf document too. It still persists its problem. But if I open the Hp service tool box through printing preference and print the test page it prints.
I have tried every thing that I can do. I've repalced the new cartiage, uninstalled the existing driver softer and installed new from hp website. Updated them and what not.
Can you tell me what is wrong with my printer? pls.

Hi,
It looks like you've tried some of the troubleshooting steps listed in this document, but there are a few more to try first. Click on the + besides the XP section and follow the steps in order. See if this helps, if it doesn't I'll look for some more.
Printer Prints Blank Sheets
Say Thanks by clicking the Kudos Star in the post that helped you. Please mark the post that solves your problem as Accepted Solution.
I am employed by HP

It wont spit out my disc

recently i tried to burn something from idvd to a blank disc, i put the blank disc in and it asked me what i want to do. I clicked ignore.
So i clicked the burn button on idvd and the disc wasnt the right one or something.
I press the eject button on my keyboard, click the help menu and do everything it says on that. I also try rip it out with tweezers. Still no luck!
Is there any way to do this without taking it down to get fixed? i have tried through dvd player etc and still no help.
Please, help i need this disc burnt quickly as someone is waiting to give me money for it!

Hey J92,
Try restarting with the mouse button pressed.
Then:
http://docs.info.apple.com/article.html?artnum=58465
then:
http://docs.info.apple.com/article.html?artnum=58566
Does it try to eject the disk? Hear whirring noises?
Yes -
If so I just retrieved a CD from my son's iMac that was trying to eject but wouldn't. I cut a tool from a plastic lid like from a salad assortment. I cut a long rectangle, the short length being like 1/2 the width of the slot, folded it over and curved the open end slightly so it opened like a pair of lips. Inserted that end into the iMac slot, ejected the disk and it came out slick as you please. The problem is that that slot gets misaligned and the disk bumps into the edge so that tool guides it out the slot.
Otherwise if that doesn't work you could take the bottom off and as a last resore you could take the iMac apart and open up the drive.
eMail me if you need instructions.
Richard

Why can't I upgrade from 10.5.8 to 10.6? My MPB spits out the disc before it ever appears on the desktop.

Why can't I upgrade from 10.5.8 to 10.6.3? My MPB spits out the disk before it ever appears on the desktop. The Snow Leopard disk is brand new, was still in shrink wrap until I opened it. I do have the hard drive partitioned, running Win XP with Boot Camp, if that might be the issue.

Hey vlntrg,
I have a 2002 model Powerbook that will sometimes (most of the time) refuse to mount a CD or DVD. It just grunts for a while and then spits it back out. When this happens, I will slap the bottom of the machine several times with an open hand, not too hard and not too soft. I read this somewhere online (I forget where), and I was hesitant to try it, but it was cheaper than replacing the SuperDrive.
This will often allow me to insert and use the CD or DVD. I have also noticed that I have less trouble when the machine is cold than when it's warm.
I've not had this trouble with my MacBook Pro.
Another thought. Would it be possible to boot your machine in target disk mode and update your software using a friend's Mac? I'm sure there are others here who can better answer that question.
Hope this helps.
Andy

Printer only spits out blank sheets

I have a photosmart 7550 and all I get when trying to print photos or even word documents is a blank page. I just installed three new print cartridges (56, 57, & 58). The calibration and diagnostic pages came out fine. I replaced the USB cable and that allowed Word to spit out a blank page.
Haven't used this printer in a long while and now I don't know how to get it to work. Any suggestions?

Hi Kaitlyn,
I have cleaned the printheads at least 5 times, tried printing reports, aligning printheads and even cleaning printhead manually and the ink cartridge also. No luck. I had no trouble with this printer until I brought everything upstairs and set up here and then that one part didn't work. The machine and printer had not been used in a week but all worked well before then. What will really be a drag is if I replace the printhead and it still will not work. This thing and I may have to have a long talk then! The monster will print in color but no black in it. Can the ink well jets be stopped up? How would anybody ever clean one of those out?
Thanks for the input and responding so quickly.
Evvy J
rainbowlady23 wrote:
@Trinity7243: have you tried cleaning the cartridges? and the printheads?
Try to go to the printer's setup MENU --> TOOLS--> CLEAN PRINTHEAD
IF its the same still, then the printheads of your printer would need to be replaced.
update me what ever happens

Spits out blank or black only prints.

Hello all, I have a HP 5740
WIndows 7
Since changing empty color and black cartridges I went with the single Photo cartridge.
I've set the options to ICM and chose the tri color cartridge option.
Now the printer will only print in black or it just spits out a blank sheet.
I understand HP doesn't officially support Windows 7 yet but I was hoping for a little insight.
I've tried what I would call EVERYTHING with no success at a color print out.

What happens if you insert a black cartridge instead of the photo cartridge and then try to print?
Make it easier for other people to find solutions, by marking my answer with \'Accept as Solution\' if it solves your problem.
Click on the BLUE KUDOS button on the left to say "Thanks"
I am an ex-HP Employee.

Have Elements 8. We now keep getting Programme error messages. Have tried to reinstall original disc but there's nothing on the disc?

Have old version of Elements 8. Keep getting programme error messages and various functions no longer work. Have tried reloading the disc but for some reason there's no longer anything on the original disc? Really don't want to have to fork out and start again.

I also have Jolly's problem. I found the iMovie 9.0.9 folder and tried to launch the older version of iMove. It would not launch. I removed all of the iMovie preferences from the Preferences folder, removed iMove 10 from the applications folder, and restarted my Mac. iMove 9.0.9 still won't launch and I can't access my videos created with the older version of iMovie. Is there a way to uninstall iMovie 10 and reinstall iMovie 9.0.9?
I am running Yosemitie on a iMac.
Paul

Spitting out blank discs, but theres a twist and it involves windows...

Similar Messages

Maybe you are looking for