Square Footage Range for AIR-AP1131AG ?

Can someone tell me the indoor square footage range for a Cisco AIR-AP1131AG ? I have someone that is purchasing this unit and wants to cover 3,500 square feet with just one access point. Thanks.

The range should be fine for that area of coverage. The 1131AG is comparable to the Cisco 4941 antenna, which Cisco says has a range of 300ft at 6Mbps. You'll need to keep several other things in mind, though.
1. Client Capacity - the 1131AG can't support much more than 20 or 25 clients.
2. RF Shadows - An open environment is one thing, but if you have anything in that room then there will be large coverage holes if only a single AP is used. This is especially true with anything metallic.
3. Redundancy - If any wireless traffic is mission-critical, you should probably install a second AP in case the first one fails.
In the end, I would recommend at least one more AP, but purchasing one and trying it out isn't a terrible idea if money is a concern.
Jeff

Similar Messages

HT201700 Voltage input range for original Macbook air 2008/2009

My charger (A1244 | 45w) no longer works. And I need to buy a new charger. Since this is for an old 2008 macbook air, the smart thing to do is buy a charger that will work with new models (that require 85w).
Apple doesn't make this power tolerance specification easily available online. This page is helpful, but doesn't provide the tolerance specification....
Intel-Based Apple notebooks: Identifying the right power adapter and power cord - Apple Support
Question:
I want to make sure that the (minimum) voltage input range for my original macbook air is between 14V and 18.5V.
Does anyone have a definitive answer for this?

"the smart thing to do is buy a charger that will work with new models (that require 85w)."
No, the smart thing is to buy the proper replacement for the power adapter. Since the power adapter connector has changed, you'll also need to purchase an adapter for the MagSafe connector.

Frequency ranges for common sounds?

What are the frequency ranges for sounds like:
Male voice
Female voice
Air conditioner hum
Flourescent light hum
Car engine
etc?
If there were a chart for the ranges of these kinds of thing I think it would make audio adjustment much easier. I currently use trial and error and have a rough idea of the ranges but have not been able to find definitive numbers.

I have footage from several different sources recorded with different microphones and I am trying to make them sound as much alike as possible.
One clip sounds muffled, another too bright, there's an airconditioner in the background of a third and so on.

Problem converting air-ap1131ag-a-k9 to Lwapp

i have a person on my team who converted some autonomoous air-ap1131ag-a-k9 to lwapp. I don't think they did it right.
what they did is , booted the ap ( at this point it was running in autonomous mode), set the ip to 192.168.1.200 and their laptop to 192.168.1.100 connected the laptop directly to the AP. (I have found out that these AP's were old AP's that previously had configs on them, ( static ips, a whole config) they came from another building , they were the ones that other lwapps replaced.)
they then went to the web gui of the AP , went to software upgrade and loaded the lwapp recovery image on the ap (c1130-rcvk9w8-tar.124-10b.JA3.tar). the software loaded fine, and converted the AP . and thats all they did
(I had mentioned that we should use the upgrade tool, but they didn't listen)
the aps got mounted , on the ceiling in the hospital, but when they went to turn them on, they didnt show up right on the controller , they kept joining and unjoining..
i think there is a problem with the SSC, i remember, something like the time had to be the same on the ap and on the WLC.
anyways, these could be older AP's before 2005 ( unknown to me) which would mean they dont hav MIC's and have SSC. and the ap is refusing them is my thought.
the WLC is setup to accept self signed certs.
anyways...
these aps are now mounted on the ceilings , and when you do a show cdp nei, it has an ip address from when it was an autonomous ap.
Also, what is the best process you have found to convert Old autonomous 1131 AP's to lightweight mode?
thanks
the controller is running 4.2.176 WLC code. i currently don't have Access to WCS or a spare controller to use with the upgrade utility.
the controller is a 4404-100

i went to the wlc and issued the command
debug lwapp events enable
i got the following output
Sat Jun 13 12:41:51 2009: 00:11:20:1a:07:a9 Received LWAPP JOIN REQUEST from AP 00:11:20:1a:07:a9 to 06:0a:10:10:00:00 on port '29'
Sat Jun 13 12:41:51 2009: 00:11:20:1a:07:a9 AP AP0011.201a.07a9: txNonce 00:00:00:00:00:00 rxNonce 00:00:00:00:00:00
Sat Jun 13 12:41:51 2009: 00:11:20:1a:07:a9 LWAPP Join Request MTU path from AP 00:11:20:1a:07:a9 is 1500, remote debug mode is 0
Sat Jun 13 12:41:51 2009: 00:11:20:1a:07:a9 Processing Radius Response: AP Authorization failure for 00:11:20:1a:07:a9
Sat Jun 13 12:41:54 2009: 00:1e:f7:ed:e8:aa Did not receive hearbeat reply from AP 00:1e:f7:ed:e8:aa
Sat Jun 13 12:41:54 2009: DTL Deleting AP 5 - 0.0.0.0
Sat Jun 13 12:41:55 2009: 00:11:21:89:fb:30 Received LWAPP ECHO_REQUEST from AP 00:11:21:89:fb:30
Sat Jun 13 12:41:55 2009: 00:11:21:89:fb:30 Successful transmission of LWAPP Echo-Response to AP 00:11:21:89:fb:30
Sat Jun 13 12:41:55 2009: 00:21:55:c2:06:20 Received LWAPP DISCOVERY REQUEST from AP 00:21:55:c2:06:20 to ff:ff:ff:ff:ff:ff on port '29'
Sat Jun 13 12:41:56 2009: 00:11:5c:03:3c:b0 Received LWAPP RRM_DATA_REQ from AP 00:11:5c:03:3c:b0
Sat Jun 13 12:41:56 2009: 00:11:5c:03:3c:b0 Successful transmission of LWAPP Airewave-Director-Data Response to AP 00:11:5c:03:3c:b0
Sat Jun 13 12:41:56 2009: 00:11:5c:03:3c:b0 Received LWAPP RRM_DATA_REQ from AP 00:11:5c:03:3c:b0
Sat Jun 13 12:41:56 2009: 00:11:5c:03:3c:b0 Successful transmission of LWAPP Airewave-Director-Data Response to AP 00:11:5c:03:3c:b0
Sat Jun 13 12:41:56 2009: 00:11:5c:03:3c:b0 Received LWAPP RRM_DATA_REQ from AP 00:11:5c:03:3c:b0
Sat Jun 13 12:41:56 2009: 00:11:5c:03:3c:b0 Successful transmission of LWAPP Airewave-Director-Data Response to AP 00:11:5c:03:3c:b0
Sat Jun 13 12:41:56 2009: 00:11:5c:03:3c:b0 Received LWAPP STATISTICS_INFO from AP 00:11:5c:03:3c:b0
Sat Jun 13 12:41:56 2009: 00:11:5c:03:3c:b0 Successful transmission of LWAPP Statistics Info Response to AP 00:11:5c:03:3c:b0
Sat Jun 13 12:41:58 2009: 00:1d:70:f4:3e:50 Received LWAPP DISCOVERY REQUEST from AP 00:1d:70:f4:3e:50 to ff:ff:ff:ff:ff:ff on port '29'
can someone help me decipher what it means, i think i need to debug to get the sha key.
there are about 14 new ap's. and they all have problems.
thanks

AIR-AP1131AG-E-K9 have been converted to LW how do I convert it back to Auto?

Hi,
One of my clients has a new WiFi solution and he has given me his old AIR AP1131AG-E-K9 to my LAB. The problem is that access-points have been converted to LW and the customer has thrown out the controller.
I do not know the enable password, how can these APs be reset to their default setting?

Resetting to Default Settings Using the CLI
Caution You should never delete any of the system files prior to resetting defaults or reloading software.
If you want to reset the access point to its default settings and a static IP address, use the write erase or erase /all nvram command. If you want to erase everything including the static IP address, in addition to the above commands, use the erase and erase boot static-ipaddr static-ipmask command.
From the privileged EXEC mode, you can reset the access point/bridge configuration to factory default values using the CLI by following these steps:
Step 1 Enter erase nvram: to erase all NVRAM files including the startup configuration.
Note The erase nvram command does not erase a static IP address.
Step 2 Follow the step below to erase a static IP address and subnet mask. Otherwise, go to step 3.
a. Enter write default-config.
Step 3 Enter Y when the following CLI message displays: Erasing the nvram filesystem will remove all configuration files! Continue? [confirm].
Step 4 Enter reload when the following CLI message displays: Erase of nvram: complete. This command reloads the operating system.
Step 5 Enter Y when the following CLI message displays: Proceed with reload? [confirm].
Caution Do not interrupt the boot process to avoid damaging the configuration file. Wait until the access point/bridge Install Mode LED begins to blink green before continuing with CLI configuration changes. You can also see the following CLI message when the load process has finished: Line protocal on Interface Dot11Radio0, changed state to up.
Step 6 After the access point/bridge reboots, you can reconfigure the access point by using the Web-browser interface if you previously assigned a static IP address, or the CLI if you did not.
The access point is configured with the factory default values including the IP address (set to receive an IP address using DHCP). To obtain the access point/bridge's new IP address, you can use the show interface bvi1 CLI command.
The 1300 series access point/bridge assumes a radio network role of a root access point. To configure it as a bridge, you must manually place it in install mode in order to align the antennas and establish a link. To establish the link you must have two access point/bridges configured in the install mode. In the install mode, one access point/bridge must be configured as a root bridge and the other a non-root bridge. To facilitate the configuration, an automatic option is available when the access point/bridge is in the install mode. After the wireless link is established and the bridge antennas are aligned, you take both access point/bridges out of install mode and place them on your LAN as root and non-root bridges.
Note "Resetting the Device to Default Settings" sectionIf xon/xoff flow control does not work, use no flow control.
Step 7 When connected, press enter or type en to access the command prompt. Pressing enter takes you to the user exec mode. entering en prompts you for a password, then takes you to the privileged exec mode. The default password is Cisco and is case-sensitive.
Note If xon/xoff flow control does not work, use no flow control.
Step 8 When connected, press enter or type en to access the command prompt. Pressing enter takes you to the user exec mode. Entering en prompts you for a password, then takes you to the privileged exec mode. The default password is Cisco and is case-sensitive.
Note When your configuration changes are completed, you must remove the serial cable from the access point.

AIR-AP1131AG-I-K9 support AES 256 bit ?

hi,
I have several AP devices:
Product/Model Number: AIR-AP1131AG-I-K9
System Software Filename: c1130-k9w7-tar.124-3g.JA
System Software Version: 12.4(3g)JA
Bootloader Version: 12.3(8)JEA
i need to know if AES 256 bit is supported by this devices and if the current software need to upgrade for that.
Regards,

HI Ben,
As per my knowledge this Software dont support 256 bit key size.
Here is the link:http://www.cisco.com/c/en/us/td/docs/wireless/access_point/12-4_3g_JA/configuration/guide/ios1243gjaconfigguide/s43wep.html
another version: 12.3(8)JA supports 256 bit key size to protect data traffic,
http://www.cisco.com/c/en/us/td/docs/wireless/access_point/12-3_8_JA/configuration/guide/1238jasc/s38wep.html
Regards
Don't forget to rate helpful posts

External number range for material master

Dear sap guru i want to create external number range for msterial master but i am facing problem .i used T.code MMNR but i am not able to tick external number small squar window . can anybody help me and tell me step by step
regards
rohit

Hi
In tcde MMNR select groups in the application tool bar a pencil like icon click that
Then go to group in the top menu bar
In that if you choose insert
Then a dialogue box will open
In that give text and
there will be two lines
First is for internal no range
second is for external no range with the check box ticked in grey
In that you have to choose the second one and give only the range interval
External tick is already there ready made in the system
If you are sure that your settings are correct in MMNR
IMG-L.G-MATERIAL MASTER-BASIC SETTINGS-MATERIAL TYPE---DEFINE ATTRIBUTES OF MATERIAL TYPES
in this choose your material type and click on its details
in the general data tab there is a external no assignmentw/o check a check box is there
Pls tick that and try to do your process by giving external no
Regards
raja
Edited by: ramanathan raja on Dec 4, 2008 2:27 PM

Number range for the customized transaction

Hi Experts,
I am developing customized screen. When user saves after entering data a number should be generated automatically. Please tell how to maintain the number ranges for my transaction.
Regards,
B V Rao

Hi,
Go to SNRO tcode and enter an object to be created and press create button.
Enter data element as S_CARR_ID and domain as POSNR
and 10% as warning and save.
create small program to update SCARR table with a carrid 01.
data : begin of itab occurs 0.
include structure scarr.
data end of itab.
itab-carrid = '01'.
append itab.
clear itab.
modify scarr from table itab.
and execute the program now your SCARR table will have 01 as carrid.
now maintain the number ranges for your newly created object in SNRO tcode
prees numer ranges button and enter 01 in Air line input field
in your program where you want these number ranges
declare a variable as follows
data number type nriv-nrlevel.
CALL FUNCTION 'NUMBER_GET_NEXT'
EXPORTING
    nr_range_nr                   = 01 " Air line just you created
    object                        = "the object name that you created in SNRO
QUANTITY                      = '1'
   SUBOBJECT                     = '"naturally enter 01 ( which you assigned while creating N ranges)
TOYEAR                        = '0000'
IGNORE_BUFFER                 = ' '
IMPORTING
   NUMBER                        = number
QUANTITY                      =
RETURNCODE                    =
EXCEPTIONS
   INTERVAL_NOT_FOUND            = 1
   NUMBER_RANGE_NOT_INTERN       = 2
   OBJECT_NOT_FOUND              = 3
   QUANTITY_IS_0                 = 4
   QUANTITY_IS_NOT_1             = 5
   INTERVAL_OVERFLOW             = 6
   BUFFER_OVERFLOW               = 7
   OTHERS                        = 8
IF sy-subrc <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
        WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
Best Regards
Ramchander Rao.K
Edited by: ramchander krishnamraju on Dec 12, 2008 9:17 AM

Hi, I have a Powermac with Mavericks and an iPhone 5S. I just recently switched from Verizon with unlimited downloads to limited of 500mb per month. I just purchased a Powerlink Outdoor Plus which is supposed to increase the network range for over 1 mile

Hi, I have a Powermac with Mavericks and a recently purchased iPhone 5S. I just switched from Verizon with unlimited downloads to limited of 500mb per month, so I purchased a Powerlink Outdoor Plus which is supposed to increase the network range for over 1 mile. I am still getting the same distance range with my iPhone with the Verizon router. I was wondering if I need to make adjustments in the Network Settings. Does anyone know about this particular subject?
Thanks,
Kevin

Okay, I'll admit I don't know much about your configuration. A standard cellular package for a cellphone means you get your signal from a tower somewhere. It won't have anything to do with a router which will be a WiFi connection from a router. If you're talking about that, the Powerlink appears to be a directional antenna. You should get better transmission/reception in the direction it is pointed, but likely worse in other directions than if you were using an omnidirectional antenna. I presume you have it all hooked up correctly so the router is actually using the Powerlink antenna.
By the way, those distance ratings are always exaggerated. Maybe you'd get 1 mile if there was only dry air between you and the antenna and no trees, buildings, etc., and that would probably be just barely getting a signal. You should see improvement but don't go to a coffeeshop 1 mile away in a city and expect to see your router. We have a directional antenna on the roof of our house that looks like a satellite dish and I barely pick up the wireless service node a block away (with apartment buildings in between). Thre may also be a difference between using it to send a signal and receiving a signal. You might even need two, one at each end, to get 1 mile.

I have on airport express that is 5 years old, I now have a new wireless router. I want to use the express just for air waving iTunes. How do I set it up?

I have on airport express that is 5 years old, I now have a new wireless router. I want to use the express just for air waving iTunes. How do I set it up?

Hello 84wvu,
It sounds like you want to setup your Airport Express to Airplay music from iTunes. I found an article with steps to help you get this setup:
Connecting to an existing Wi-Fi network, exclusively for iTunes music
AirPort Express used exclusively for AirPlay by setting it up in Client Mode.
Choose this configuration if the computer containing your iTunes library may be out of direct range of the AirPort Express, but is within range of the Wi-Fi network.
How to Set It Up
Connect your AirPort Express to your home stereo or powered speakers.
From your computer, join the wireless network. Use the AirPort status menu in the menu bar on a Mac. On a Windows-based computer, hold the pointer over the wireless connection icon until you see your AirPort network name (SSID), and choose it from the list if there are multiple networks available. Enter the network password, if necessary.
Open iTunes on your computer and choose the AirPort Express(es) you wish to stream music through from the speakers pop-up menu in the lower-right corner of the iTunes window.
I also recommend reviewing the sections titled "Some things you should know about AirPort Express with AirPlay" and "Things to consider before you begin" in the full article:
Wi-Fi base stations: How to set up and configure AirPort Express for AirPlay and iTunes
http://support.apple.com/kb/ht4587
Thank you for posting in the Apple Support Communities.
Best,
Sheila M.

Urgent : Unable to maintain the Number ranges for Excise Groups

Hi CIN experts............
In Development server I created 3 excise Groups (E2,E3 and E4), the same I was transported to Production.
J_1IRG23A1, J_1IRG23A2 object number ranges are Excise Group specific.
When I go to Tools - Number Ranges to maintain number range for J_1IRG23A1, J_1IRG23A2 objects I didn't find these excise groups.
Im able to see these Excise groups in Tools - Number ranges in Development server, but not in Production.
Can any one guide me something to resolving the issue ?
regards
Durga Ram

Hello Nagaraju,
Can you please tell me the customozing path for maintaining the number ranges for PM log entries.
I require to mention customizing path in my document.
Puneet

How to find next number range for project definition in tcode CJ20N

Hai Experts,
Please help me 'How to find next number range for project definition in tcode "CJ20N". I was trying in function module NUMBER_GET_NEXT. Is it right function module? If its right what input i need to give for this tcode and for the field project definition?
Note: I searched in forum before posting, but couldn't find the solution.
Thanks
Regards,
Prabu S.

Hi,
For project defination internal number is assigned by system.
When you saves's project then system allocate one number to project defination, you can view it,
SE11 >>> table PROJ >> Click on contents >>> execute,
here you will get your project defination & number is assigned to project defination.
kapil

Number ranges for material document (migo) and inventory documents

Hi Gurus,
We need a different number ranges for goods receipt documents and inventory documents because we have different company merged in to one box.Can any body tell me on what basis we differenciate the number ranges how to configure it.
If we take PO, we have different doc types and we assign number ranges to those documents. in case of Miro , it is the single transaction code used by different companies and how to give different number ranges.
Regards,
Sri........

Hi,
I think number ranges of inventory documents are on client level not on company code wise . because even though your creating new document and assigned different number ranges for the documents but these while assigning ranges to T codes (MIGO or MIRO) you dont have option like company codes ( tcode OMBA) so number ranges for inventory documents are at client level not at company code level.

Excise invoice number range for Depot

Hi All,
Pls guide me to assgin excise invoice number range for Depot.
My client asking me to assgin domestic and export excise number range for Depot.
pls clarrify:
What are the purposes of the number range objects J_1IEXCLOC and J_1IEXCINV? In which conditions
1. either of the two, or 2. both the objects should be used?
Thanks,
Muru..

Dear Murugan
Please search in forum you can have ready made answers available.
System will always assigns one number for excise(where user can use Official document number) also an internal number for statistical purpose.(internal number for excise)
You can see all these numbers in tables J_1IEXCHDR/J_1IEXCDTL.
Just enter one excise Invoice number in the above tables & compare these with the objects J_1IEXCLOC/J_1IEXCINV...you will get more clarity
Hope this helps.
Phanikumar

Sales /Outgoing Excise Invoice number Range for J1IIN

Dear Gurus,
We are doing STO from excisable plant 1000 to plant 1100. We created a PO with document type UB ( STO) and created delivery with reference to PO and created billing document ( delivery challan). Against billing document number we created sales excise invoice in J1IIN for financial year starting from 1st April 2010. In J1I9 we have maintained number range for 2010 financial year in object J_1IEXCLOC for respective series group s1.Still when the outgoing excise created, the system continued last financial years number range. In entire flow from PO till MIGO and billing document and creation of excise invoice the input date is 6th of April i.e. current financial year. This is our first sales outgoing excise invoice creation in new financial year for which number range is maintained properly.
My question is why system took last financial years number range even though the date in all the documents is falling in new financial year.
Will appreciate the answer.
Thanx in advance
Regards
Nilesh

RESOLVED

Square Footage Range for AIR-AP1131AG ?

Similar Messages

Maybe you are looking for