Srcpac config questions

First off does anyone use srcpac?
I would like to know if there is a way to specify a directory for the sources when they are downloaded? I don't want all the sources scattered throughout abs as it will make it very difficult to use and very messy.
Also, is there a way to recompile my entire OS using srcpac? I didn't see this mentioned anywhere in the man page or --help
This might not be the correct forum area for this but i wasn't sure where to put it.

I figured it out.
Thanks for the help...

Similar Messages

A few post config questions on new setup

Hi Group,
Just a few post config questions.
First, how can I confirm my controller is in fact associating properly with an NTP server? On a typically cisco product, I could just do a 'show ntp associations' or a 'show ntp status'. I cannot see a way to confirm this on the gui or command line.
Second, on my guest network with web-auth, if one were to choose to not use https for web-auth and instead use unsecure http, would that be possible and if so where in the gui?
Thanks.

The third field is from a WLC running v7.4 not v7.2. I usually would install a 3rd party certificate, but what eles you can try is issue this command on from the CLI. It had issues working with certain code versions, but you might as well give it a try.
config network web-auth secureweb disable
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"

Workshop Weblogic config questions

I'm using Oracle Workshop for WebLogic 10.3 and I'm hoping someone can answer some setup/config questions.
When I double click on the server (WebLogic Server v10.3 at localhost) a window opens with various settings that manage how workshop and weblogic work together.
Under "Startup & Deployment" I have the following turned on:
Launch WebLogic server in Eclipse console
Always start WebLogic Server in debug mode
Ignore project compilation errors when publishing (I have this turned on because of errors in a portal project, the errors aren't inmportant, and don't prevent the project form running)
Run stand-alone web module directly from workspace
So, first question, with these settings I was able to quickly switch to debug mode, with out restarting the server, now the server restarts whenever I turn debugging on. What have I done that has stopped this working correctly? How can I get it to start debugging without a full restart?
next question, what happens if I turn on "Start WebLogic Server in Express Mode"? As far as I can tell nothing happens.
Lastly, under "Automatic Publishing" I have it set to "Never publish automatically", if I choose another setting workshop essentially freezes because it's constantly publishing. So whenever I make a change, even in a jsp, I need to remove the project, then re-add it to see my changes in the browser. This is frustrating, not just because it takes 8 or 9 minutes (8 or 9 MINUTES!!!), but because the project doesn't run properly until it is redeployed. You'd think that if it needs to be re-deployed, then none of my changes should matter on the server until it is re-deployed.
So, my question is, Is there any way to get this re-deployment to happen faster?
Thanks for any and all help

Well, in my experience performance is not bad as you experienced. Is it locally connected server or remotely connected server? If it is a remote server, network issue could cause this latency issue.
Is performance better if you run the server without enabling debug mode? If yes, probably you can also review any break points set.
You could also try out the following options
1) Run workshop with -clean option, by opening command prompt and navigating to workshop_home\'workshop.exe -clean'
2) Untick the option 'Launch WebLogic server in Eclipse console' and start server which would enable server to start on command prompt
3) This would enable you to take multiple thread dumps (cutl +Break) on the server console output, while performance is very bad, to see where threads are halt.

Re: PLM4P v6003 Config Question: Any way to configure UGM Notifications?

After reading:
PLM4P v6003 Config Question: Any way to configure UGM Notifications?
This is one of the requirements from me as well. We always wanted to customize emails sent not only for UGM but also for other modules. We wanted to conveysome message to approvers. But it seems this is still not possible. Is this functionality on road-map of AgielP4P product management?

Currently, the subject and body of emails can be customized to an extent, as they are translations that can be overridden. The translations have some placeholder fields that get populated by the system, but you are limited to those placeholder fields. The upcoming release will give you full control of the email body and subject lines, for GSM and SCRM emails, as well as Supplier Rep emails.

Redundant FWSM Config Question

Hello All,
I'm going to be configuring failover with FWSMs for our 6500 at my job and I have a config question. There is one current 6500 chassis with 2 FWSMs installed. They are both online but currently since failover isn't setup, only one FWSM is actually active. My question is since we are using mutiple contexts where do I setup the failover interface, and do I need to configure failover on every single vlan on the FWSM? We have over 10 contexts each with 2-3 interfaces on them, so do I need a failover IP for every vlan that exists on every context? Also, does the failover config get setup on the admin or system context? Any help would be greatly appreciated, and thank you so much in advance!

Hi John.
Failover config goes in the system context. For the data interfaces in each context, you will need a primary and a standby IP i.e. 2 IP's per VLAN. Once failover happens, the secondary FWSM will assume the active role and the secondary FWSM will take over the Primary IP address thus making the failover process transparent to end users.
HTH.
Regards
Zubair

SCCM 2012 application portal: config questions

Hi,
We have setup SCCM 2012 application portal correctly and it's working fine.
However some config questions:
-can we change the name of the configuration portal? Now its servername/CMApplicationCatalog ... what's not userfriendly.
We'd like it to be applicationportal.ourcompany.com. Howto achieve that?
-can we customize layout in a supported way (we could change html pages but after an upgrade of SCCM they would/could be erased)?
-how does flexera (adminstudio?) plugs in into this. I've read this entry
http://helpnet.installshield.com/appportal2014/Content/helplibrary/AP_CreatingCatItemSCCM.htm but what's the big picture here? Anybody using this? What are the advantages?
J.
Jan Hoedt

We want to offer software center for overview of mandatory installs, application catalog for optional software.
On our companies portal, we can then set a link which directs to the application portal. User can then install optional software from there.
My current config works http://applicationportal.ourcompany.com/ goes to the sccm-server but not to the url below.
That would be http://applicationportal.ourcompany.com/CMApplicationCatalog/#/SoftwareLibrary/AppListPageView.xaml
how can I make sure the application portal shows up when this link is opened?
It sounds like you want to perform a URL rewrite?
http://www.iis.net/learn/extensions/url-rewrite-module/creating-rewrite-rules-for-the-url-rewrite-module
You should test this to see if it's what you want - I may have misunderstood your question.
Also, I wouldn't host this module on your AppCatalog server, I'd host the rewrite module elsewhere.
Don
(Please take a moment to "Vote as Helpful" and/or "Mark as Answer", where applicable.
This helps the community, keeps the forums tidy, and recognises useful contributions. Thanks!)

SSL VPN Full and Split Tunnel Config Question

I am Beta testing SSLVPN on an IOS router. The question I have is this:
Is it possiable to have slit and full tunnel configs. It seems that once you create your context and default profile that is all you have either split or full. The books say you can use Radius and assign different profiles but, I would like to give the users a choice (like in the VPN3000 .pcf) of either split or full depending on where they are working from.

The below is an example using the ASA - but the principle remains the same:-
http://www.cisco.com/en/US/customer/products/ps6120/products_configuration_example09186a0080975e83.shtml
HTH>

J2EE Policy agent - login page config questions

Hi,
I'm trying to configure a customized login page for an application that is protected by a AM Policy Agent 2.2-01 on SJSAS 8.2.
I am aware of this link:
http://docs.sun.com/app/docs/doc/820-2539/gatai?l=en&a=view .
This describes configuring the custom login for an app. Based on the doc, I have configured the following:
1. I have the agent and my app on one instance on myhost.mydomain.com
2. A url policy is protecting my app, configured in Access Manager 7.1. The url is http://myhost.mydomain.com:38080/myapp/*
3. In my app's web.xml I have the following:
<login-config>
        <auth-method>FORM</auth-method>
        <form-login-config>
            <form-login-page>/login.jsp</form-login-page>
            <form-error-page>/loginerror.jsp</form-error-page>
        </form-login-config> 4. In AMAgent.properties:
com.sun.identity.agents.config.login.form[0] = /myapp/login.jsp
com.sun.identity.agents.config.login.error.uri[0] = /myapp/loginerror.jsp
com.sun.identity.agents.config.login.use.internal = false
com.sun.identity.agents.config.login.content.file = FormLoginContent.txtThere doesnt seem to be any change in login page when I go to my app. It just redirects to the Access Manager login page, and when I login it redirects back to the app. The security behavior is correct but I would like the login page to be unique for the app.
So my questions are:
1. Am I using com.sun.identity.agents.config.login.use.internal correctly? I dont want it to use internal login, but my login file, right?
2. My login page is protected by my url policy. Is that a problem? Should I be using com.sun.identity.agents.config.notenforced.uri[0] on the login page?
3. Can anyone clarify to me exactly how and where the contents of FormLoginContent.txt is used?
I'm kind of new to AM and Policy Agents, so i apologize if my questions seem very newb. Any help is appreciated. Thanks!
-Matt

Changing com.sun.identity.agents.config.filter.mode to URL_POLICY seemed to help. I am now seeing /myapp/login.jsp as the login page for my app. The logins themselves are failing, however. I am confused as to how to set up the jsp to work with the agent to log in.
-Matt

11gR2 em install / config question.

We just loaded 11gR2 onto a virtual server running Win 2008 Server R2. During the installation of the database,
I received 5 or 6 missing file messages and I told the installer to ignore and continue. One of those files was
dbhome_1\...\em.jar.
Will this preclude me from getting em up? Should I deinstall/reinstall the 11gR2?
When I ran emctl start dbconsole I received this message:
can't locate CompEMdbconsole.pm in @inc <@inc contains ..(list of files).......emctlCommon.pm line 598
From this question you'll probably surmise that I'm relatively inexperienced.
Suggested reading info is always appreciated.
Thanks,
Ron
Edited by: RonW on Oct 9, 2012 6:27 AM

Thanks for the reply. I used dbca to create a database which I had thought was done
during the original install. It ran forever and eventually gave me an error message
'Error Instantiating OC4J files'. When I looked in the emconfig.log file, there were
several missing xml files in E:\app\Administrator\product\11.2.0\dbhome_1\oc4j\j2ee\
OC4J_DBConsole\config\
jms.xml
rm1.xml
http-web-site.xml
server.xml
In fact, the 'config' folder was empty. Going back to my original question regarding
those missing files, why would they be missing? Is the oem a separate install
process or is it done when the 11g database is installed?
Thanks, Ron

ACE: design/config question: trans.slb + slb + mngt

Hi,
Could this ACE setup/design work?
I want PROXIED sessions (to VIP proxy 10.0.0.10) to be loadbalanced
All other sessions (eg. Some public ip's) will have to transparent loadbalanced to proxy servers. Thus not destinations NAT
ACE is inline between firewalls and proxy servers.
Vip definitions:
class-map match-all P_PXYVIP_VS_LB
2 match virtual-address 10.0.0.10 255.255.255.255 tcp 8080
class-map match-all P_PXYTRANS_VS_LB
2 match virtual-address 0.0.0.0 0.0.0.0 tcp any
Question in this case: would it still be possible to have management sessions towards proxy servers routed by the ACE ? (physical ip addresses of proxy)
Probably the classmap PXYTRANS is catching those sessies also.
Are there other design/config solutions to solve this one?
Thank you!
Wim

Let me repose the question:
How could one still be able to access the realserver IP (which is directly connected
to the ACE) for manangement.
Knowing that there is 1 VIP which (normal) loadbalance to the realservers
and
there is 1 VIP 0.0.0.0 tcp any which is configure to catch all other traffic to be
transparant loadbalanced.
The VIP 0.0.0.0 is always catching the sessions which need only to be routed
to the real servers ip.

Voice GW Config Question

Hi Everyone
Yesterday I posted a question about redesigning the way our voice network looks, I'm removing 6 CUCM 4.3 boxes and I'm going to have those sites register with our Sub which is 10.5.1 in our data center across the WAN. Jaime answered my question and gave me some good insight on what to do for each site.
1.Create DP,CSS,PT on the Pub
2.Enable SRST on the GW
3.Make necessary changes on GW
4.Create LRG to have the site use their local GW
I've been reading on how to get these task done and I have a question about #3, I'm looking at the config from the GW for the test sight and the VoIP dial peer is referencing the CUCM node currently on site. Would modifying the IPV4 address to reflect the new CUCM node at the data center be the only change that I would have to make to the config?
I also want to say thanks for all the help that everyone has given me with really quick responses to my questions. I just changed jobs and I went from doing primarily MACD to now I'm actually the person who is doing the implementation. I've never done implementation before but I know if I stick with it and help from this board I'll be a super star yet.
Eric

Correct, need to change the IP address on the DP to reflect the new one. Also, need to look at SCCP resources (conference bridge or transcoders if any) and those need to be changed.

SSPR config question

Hi,
Assume we have 2 different user types: staff and students.
Student accounts reside in their own forest
Staff accounts reside in 2 different and separate forests
FIM resides in another separate forest (a resource forest)
We are about to deploy SSPR in the resource forest, and need the following functionality:
When resetting the password, Staff will type in "domain\username"; Staff will use the question & answer SSPR approach
however Students will use the OTP approach and only type in their "username" since many won't know the domain name (we will set the 'defaultdomainName' attribute in the config file)
My question is this:
Because we need 2 different SSPR approaches and for Students we need the 'defaultdomainName' prepopulated - will we need 2 separate instances of the SSPR Portal deployed on 2 separate servers?
Thanks,
dw

Going strictly by the book, you would need two separate instances of the SSPR Portal if it's critical to vary the behavior of the default domain name. If folks in the non-default domain will always enter DOMAIN\user or UPN, then one instance of the
portal should suffice.
That aside, Sameera_man's links are relevant for creating the necessary resources to support more than one Password Reset Authn workflow.
Steve Kradel, Zetetic LLC

ASA5505 NAT CONFIG QUESTION? OPEN STATIC IP

8.2
HI ALL
Here is my scenerio and I have worked on this with TAC support over the last month, we finally made progress by getting our ISP to activate the 5 static IPs but here is my issue.
basically we have a VOIP phone that is "remote". This phone needs to come through the Public IP to an internal address of 192.168.10.57.
We tried only allowing certain "ports" to pass, such as SIP, RTP> but the remote phone still cannot reach the phone server at 192.168.10.57
So
I want to open it completely as this phone pc is the ONLY device on that public IP.
so my 2 questions are.
what do i need to config as a rule/ command to make this happen. were I want the public IP of 50.x.x.x to corelate directly and openly to the internal of 192.168.10.57?
Also what is the command to allow the public IP to be pingable? so i can just confirm that it is reachable. I know at the very end we turned it off with a sort of ICMP command.
Thank you all for your time and help. if you need more info please ask.

Thank you very much for your help.
I applied
access-list out-in extended permit icmp any host 50.x.x.x
and now i can ping TY
But,
I applied
static (inside,outside) 50.245.59.98 192.168.10.57 netmask 255.255.255.255
ANd got this error:
ciscoasa(config)# static (inside,outside) 50.245.59.98 192.168.10.57 netmask 2$
ERROR: mapped-address conflict with existing static
inside:192.168.10.57 to outside:50.245.59.98 netmask 255.255.255.255
I just want this port "wide open" to see if the remote phone will connect to it.
here is my edited SH RUN
ASA Version 8.2(1)
hostname ciscoasa
enable password PfdcbR/f90Mel1yp encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Vlan1
nameif inside
security-level 100
ip address 192.168.10.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 50.X.X.X 255.255.255.248
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
banner login
banner login &
banner login ~
banner login ***********Warning*******
banner login
banner login ^
ftp mode passive
access-list out-in extended permit tcp any host 50.X.X.X eq 3462
access-list out-in extended permit tcp any host 50.X.X.X eq sip
access-list out-in extended permit tcp any host 40.X.X.X eq ftp-data
access-list out-in extended permit tcp any host 40.X.X.X eq ftp
access-list out-in extended permit icmp any host 50.X.X.X
access-list split standard permit 192.168.10.0 255.255.255.0
access-list nonat extended permit ip 192.168.10.0 255.255.255.0 192.169.169.0 255.255.255.0
access-list FTP remark Allow
access-list FTP extended permit tcp any eq ftp any eq ftp
access-list FTP extended permit tcp any any eq ftp-data
pager lines 24
logging enable
logging buffered debugging
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool ippool 192.169.169.1-192.169.169.254 mask 255.255.255.0
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list nonat
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) tcp interface ftp 192.168.10.2 ftp netmask 255.255.255.255
static (inside,outside) tcp interface ftp-data 192.168.10.2 ftp-data netmask 255.255.255.255
static (inside,outside) 50.X.X.X 192.168.10.57 netmask 255.255.255.255
access-group out-in in interface outside
route outside 0.0.0.0 0.0.0.0 50.X.X.X 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
aaa authentication telnet console LOCAL
aaa authentication http console LOCAL
http server enable
http 0.0.0.0 0.0.0.0 inside
http 192.168.10.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
sysopt connection timewait
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
telnet 0.0.0.0 0.0.0.0 inside
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 inside
ssh 0.0.0.0 0.0.0.0 outside
ssh timeout 5
console timeout 0
management-access inside
dhcpd address 192.168.10.50-192.168.10.100 inside
dhcpd dns 75.75.75.75 75.75.76.76 interface inside
dhcpd lease 86400 interface inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics port
threat-detection statistics protocol
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
enable outside
svc image disk0:/anyconnect-dart-win-2.5.3041-k9.pkg 1
svc enable
port-forward rdpfromsslvpn 5050 50.X.X.X 5050 remote desktop server from ssl vpn
tunnel-group-list enable
group-policy RemoteAccess internal
group-policy RemoteAccess attributes
banner value *****************************WARNING**********************************
banner value Access Beyond This Point Requires Prior Authorization from your Network Administrator
banner value ****************************************************************************
vpn-tunnel-protocol svc webvpn
split-tunnel-policy tunnelspecified
split-tunnel-network-list value split
webvpn
url-list none
svc ask enable default webvpn
username aalmonte password m7vzxUlfTDi05gS6 encrypted privilege 0
username aalmonte attributes
vpn-group-policy RemoteAccess
username mmaccormack password IWIdkIPCDtg4CmHR encrypted privilege 0
username mmaccormack attributes
vpn-group-policy RemoteAccess
username lmaccormack password qRsbIpdvRgZhIVS/ encrypted privilege 0
username lmaccormack attributes
vpn-group-policy RemoteAccess
username admin password V8ctuy0OtxmDU4HD encrypted privilege 15
username rdirkee password mHVkPntgw4LQyh.U encrypted
username rdirkee attributes
service-type remote-access
username wmaccormack password AhNi5Rk6JFlHU9Fy encrypted privilege 0
username wmaccormack attributes
vpn-group-policy RemoteAccess
username cisco password 3USUcOPFUiMCO4Jk encrypted privilege 15
username rickg password 46/GVMAZTuz4ywzs encrypted privilege 0
username rickg attributes
vpn-group-policy RemoteAccess
service-type remote-access
username jgoucher password fMhOfzHeEB1lu9z6 encrypted privilege 0
username jgoucher attributes
vpn-group-policy RemoteAccess
username smaccormack password LCkB1kwdtIbPmtQK encrypted privilege 0
username smaccormack attributes
vpn-group-policy RemoteAccess
username rmaccormack password JG98o0q2ozZeYYrv encrypted privilege 0
username rmaccormack attributes
vpn-group-policy RemoteAccess
username bmaccormack password JTx67mnIFw62G6kx encrypted privilege 0
username bmaccormack attributes
vpn-group-policy RemoteAccess
tunnel-group RemoteAccess type remote-access
tunnel-group RemoteAccess general-attributes
address-pool ippool
default-group-policy RemoteAccess
tunnel-group RemoteAccess webvpn-attributes
group-alias RemoteAccess enable
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect icmp
service-policy global_policy global
prompt hostname context
TYVM

PIX/ASA site-to-site VPN config question

Do I need to specify the source IP address & mask in my access-list that's referenced in the crypto map "match address" line or can I just say "any"?
If I want to send certain traffic to one tunnel and other traffic to a different tunnel based solely on the destination address, can my access lists look like:
access-list main_tunnel extended permit ip any 192.168.1.0 255.255.255.0
access-list other_tunnel extended permit ip any 192.168.2.0 255.255.255.0
(and then, obviously, reference the appropriate access list in two different "crypto map" configs.
I'm just wondering because all the examples & templates that I've seen specify both the source & destination IPs but since all my sites just have one subnet on the LAN, I might as well just say "any", right?
Any downside to this?

The downside is the other end should be a mirror of the main end.
permit ip 192.168.1.0 255.255.255.0 any
permit ip 192.168.2.0 255.255.255.0 any
and you probably don't want that.

Conky config question - running in multiple columns?

Is it possible to display conky's output in rows rather than in columns? Example: I want to more or less cut my config in 1/2 and have the temps+ everything under them appear to the right of the CPU usage bit.
# Swap Usage:$color $swapperc%${color lightgrey}
# the ${template x x x} command uses /sys/bus/platform/devices
# for this to work you need both lm-sensors and hddtemp
# get both from main repos
# set to yes if you want Conky to be forked in the background
background no
own_window yes
own_window_type override
own_window_transparent yes
own_window_hints undecorated,below,sticky,skip_taskbar,skip_pager
out_to_console no
# X font when Xft is disabled, you can pick one with program xfontsel
#font 7x12
#font 6x10
#font 7x13
#font 8x13
#font 7x12
#font *mintsmild.se*
#font -*-*-*-*-*-*-34-*-*-*-*-*-*-*
#font -artwiz-snap-normal-r-normal-*-*-100-*-*-p-*-iso8859-1
# Use Xft?
use_xft yes
# Xft font when Xft is enabled
xftfont Bitstream Vera Sans Mono:size=8
#own_window_transparent no
#own_window_colour hotpink
# Text alpha when using Xft
xftalpha 0.8
#on_bottom yes
# Update interval in seconds
update_interval 2
# Create own window instead of using desktop (required in nautilus)
#own_window no
# Use double buffering (reduces flicker, may not work for everyone)
double_buffer yes
# Minimum size of text area
#minimum_size 250 5
maximum_width 258
# Draw shades?
draw_shades no
# Draw outlines?
draw_outline no
# Draw borders around text
draw_borders no
# Stippled borders?
stippled_borders 10
# border margins
border_margin 4
# border width
border_width 1
# Default colors and also border colors
default_color white
default_shade_color white
default_outline_color white
# Text alignment, other possible values are commented
#alignment top_left
#minimum_size 10 10
#alignment top_right
alignment bottom_left
#alignment bottom_right
# Gap between borders of screen and text
gap_x 12
gap_y 37
# Add spaces to keep things from moving about? This only affects certain objects.
use_spacer no
# Subtract file system buffers from used memory?
no_buffers yes
# set to yes if you want all text to be in uppercase
uppercase no
TEXT
${color #ddaa00}$nodename$color
$sysname $kernel on $machine
${color lightgrey}Uptime:$color $uptime ${color lightgrey}- Load:$color $loadavg${color lightgrey}
RAM Usage:$color $memperc% or $mem of $memmax${color lightgrey}
$color$stippled_hr${color lightgrey}
Intel Xeon X3360 @ $color${freq_g} GHz${color lightgrey} (Vcc: ${execi 8 sensors | grep Vcc | cut -c15-19} V)
${color black}${cpugraph 000000 5000a0}${color lightgrey}
${color lightgrey}Core0:$color ${platform coretemp.0 temp 1} °C${color grey} @$color ${cpu cpu1}% ${alignr}${cpubar cpu1 6,120}
${color lightgrey}Core1:$color ${platform coretemp.1 temp 1} °C${color grey} @$color ${cpu cpu2}% ${alignr}${cpubar cpu2 6,120}
${color lightgrey}Core2:$color ${platform coretemp.2 temp 1} °C${color grey} @$color ${cpu cpu3}% ${alignr}${cpubar cpu3 6,120}
${color lightgrey}Core3:$color ${platform coretemp.3 temp 1} °C${color grey} @$color ${cpu cpu4}% ${alignr}${cpubar cpu4 6,120}${color grey}
${color grey} CPU:$color ${platform it87.656 temp 2} °C ${color grey} Fan1:$color ${platform it87.656 fan 1}${color grey} RPM @ $color${execi 8 cat /sys/class/hwmon/hwmon4/device/pwm1}
$color$stippled_hr${color lightgrey}
${color grey} GPU:$color ${execi 8 nvidia-settings -q gpucoretemp | grep nov | cut -c42-43} °C ${color grey} M/B:$color ${platform it87.656 temp 1} °C
${color grey} sda:$color ${execi 300 sudo hddtemp /dev/sda | cut -c25-26} °C ${color grey} sdb:$color ${execi 300 sudo hddtemp /dev/sdb | cut -c34-35} °C ${color grey} sdc:$color ${execi 300 sudo hddtemp /dev/sdc | cut -c33-34} °C
$color$stippled_hr${color lightgrey}
${color slate grey} /dev/shm: ${color }${fs_used_perc /dev/shm} % ${fs_bar /dev/shm}
${color grey}$stippled_hr${color light grey}
${color lightgrey}Processes:$color $processes ${color grey}Running:$color $running_processes
${color}Name PID CPU% MEM%
${color #ddaa00} ${top name 1} ${top pid 1} ${top cpu 1} ${top mem 1}
${color lightgrey} ${top name 2} ${top pid 2} ${top cpu 2} ${top mem 2}
${color lightgrey} ${top name 3} ${top pid 3} ${top cpu 3} ${top mem 3}
${color}Mem usage
${color #ddaa00} ${top_mem name 1} ${top_mem pid 1} ${top_mem cpu 1} ${top_mem mem 1}
${color lightgrey} ${top_mem name 2} ${top_mem pid 2} ${top_mem cpu 2} ${top_mem mem 2}
${color lightgrey} ${top_mem name 3} ${top_mem pid 3} ${top_mem cpu 3} ${top_mem mem 3}

There are 4 files, so I am running 4 instances of conky. I will post the files from left to right.
background no
update_interval 1.0
double_buffer yes
use_xft no
xftfont Monospace:size=10
xftalpha 0.8
own_window yes
own_window_transparent yes
own_window_type override
own_window_hints undecorated,below,sticky,skip_taskbar,skip_pager
#on_bottom yes
minimum_size 320 42
draw_shades no
draw_outline yes
draw_borders yes
draw_graph_borders no
stippled_borders 0
border_margin 0
border_width 0
default_color white
default_shade_color black
default_outline_color black
alignment top_left
gap_x 10
gap_y 875
#gap_y 10
no_buffers yes
TEXT
Toshibuntu
${hr}
${color #F09000}Uptime${color #707070}:$color $uptime
${color #F09000}Load${color #707070}:$color $loadavg
${color #F09000}Battery${color #707070}:${color white} ${execi 15 /usr/bin/bat.pl}% ${color white} ${execibar 15 /usr/bin/bat.pl}
${color #F09000}CPU${color #707070}:${color white} ${cpu}% ${freq}MHz ${color #F09000}Temp${color #707070}:$color ${acpitemp} F${color grey}
${cpugraph 000000 5000a0}
${color #F09000}Memory${color #707070}:${color white} ${memperc}% $mem/$memmax
${memgraph 000000 5000a0}
background no
update_interval 1.0
double_buffer yes
use_xft no
xftfont Monospace:size=10
xftalpha 0.8
own_window yes
own_window_transparent yes
own_window_type override
own_window_hints undecorated,below,sticky,skip_taskbar,skip_pager
#on_bottom yes
minimum_size 250 42
draw_shades no
draw_outline yes
draw_borders no
draw_graph_borders no
stippled_borders 0
border_margin 0
border_width 0
default_color white
default_shade_color black
default_outline_color black
alignment top_left
gap_x 332
gap_y 875
#gap_y 10
no_buffers yes
TEXT
${color white}Processes
${hr}
${color}Name PID CPU% MEM%
${color #ddaa00} ${top name 1} ${top pid 1} ${top cpu 1} ${top mem 1}
${color lightgrey} ${top name 2} ${top pid 2} ${top cpu 2} ${top mem 2}
${color lightgrey} ${top name 3} ${top pid 3} ${top cpu 3} ${top mem 3}
${color lightgrey} ${top name 4} ${top pid 4} ${top cpu 4} ${top mem 4}
${color}Mem usage
${color #ddaa00} ${top_mem name 1} ${top_mem pid 1} ${top_mem cpu 1} ${top_mem mem 1}
${color lightgrey} ${top_mem name 2} ${top_mem pid 2} ${top_mem cpu 2} ${top_mem mem 2}
${color lightgrey} ${top_mem name 3} ${top_mem pid 3} ${top_mem cpu 3} ${top_mem mem 3}
${color lightgrey} ${top_mem name 4} ${top_mem pid 4} ${top_mem cpu 4} ${top_mem mem 4}
background no
update_interval 1.0
double_buffer yes
use_xft no
xftfont Monospace:size=10
xftalpha 0.8
own_window yes
own_window_transparent yes
own_window_type override
own_window_hints undecorated,below,sticky,skip_taskbar,skip_pager
#on_bottom yes
minimum_size 275 42
draw_shades no
draw_outline yes
draw_borders no
draw_graph_borders no
stippled_borders 0
border_margin 0
border_width 0
default_color white
default_shade_color black
default_outline_color black
alignment top_left
gap_x 580
gap_y 875
#gap_y 10
no_buffers yes
TEXT
Networking
${hr}
${color #F09000}wlan0${color #707070}:${color white} ${addr wlan0}
${color #F09000}Downspeed${color #707070}: ${color white}${downspeed wlan0}k ${color #F09000}Upspeed${color #707070}: ${color white}${upspeed wlan0}k
${color black}${downspeedgraph wlan0 30,90 000000 5000a0} $alignr${color black}${upspeedgraph wlan0 30,90 000000 5000a0}
${color #F09000}eth0${color #707070}:${color white} ${addr eth0}
${color #F09000}Downspeed${color #707070}: ${color white}${downspeed eth0}k ${color #F09000}Upspeed${color #707070}: ${color white}${upspeed eth0}k
${color black}${downspeedgraph eth0 30,90 000000 5000a0} $alignr${color black}${upspeedgraph eth0 30,90 000000 5000a0}
background no
update_interval 1.0
double_buffer yes
use_xft no
xftfont Monospace:size=10
xftalpha 0.8
own_window yes
own_window_transparent yes
own_window_type override
own_window_hints undecorated,below,sticky,skip_taskbar,skip_pager
#on_bottom yes
minimum_size 415 42
draw_shades no
draw_outline yes
draw_borders yes
draw_graph_borders no
stippled_borders 0
border_margin 0
border_width 0
default_color white
default_shade_color black
default_outline_color black
alignment top_left
gap_x 855
gap_y 875
#gap_y 10
no_buffers yes
TEXT
${color white}File Systems
${hr}
${if_mounted /}${color #F09000}/${color #707070}: $color${fs_used /}/${fs_size /} ${color #F09000}Free${color #707070}: $color${fs_free /} ${fs_bar /}$endif
${if_mounted /media/Elements}${color #F09000}Elements${color #707070}: $color${fs_used /media/Elements}/${fs_size /media/Elements} ${color #F09000}Free${color #707070}: $color${fs_free /media/Elements} ${fs_bar /media/Elements}$endif
${if_mounted /media/data}${color #F09000}data${color #707070}: $color${fs_used /media/data}/${fs_size /media/data} ${color #F09000}Free${color #707070}: $color${fs_free /media/data} ${fs_bar /media/data}$endif
${if_mounted /media/host}${color #F09000}host${color #707070}: $color${fs_used /media/host}/${fs_size /media/host} ${color #F09000}Free${color #707070}: $color${fs_free /media/host} ${fs_bar /media/host}$endif
${if_mounted /media/studio}${color #f09000}studio${color #707070}: $color${fs_used /media/studio}/${fs_size /media/studio} ${color #F09000}Free${color #707070}: $color${fs_free /media/studio} ${fs_bar /media/studio}$endif
${if_mounted /media/elements}${color #f09000}elements${color #707070}: $color${fs_used /media/elements}/${fs_size /media/elements} ${color #F09000}Free${color #707070}: $color${fs_free /media/elements} ${fs_bar /media/elements}$endif
${if_mounted /mnt/ubuntu}${color #F09000}ubuntu${color #707070}: $color${fs_used /mnt/ubuntu}/${fs_size /mnt/ubuntu} ${color #F09000}Free${color #707070}: $color${fs_free /mnt/ubuntu} ${fs_bar /mnt/ubuntu}$endif
I put the 4 files in my home directory and named them
.conkyrc
.conkyrctop
.conkyrcnet
.conkyrcfile
I use the following bash script to start them all
#!/bin/bash
conky -c ~/.conkyrc &
conky -c ~/.conkyrctop &
conky -c ~/.conkyrcnet &
conky -c ~/.conkyrcfile &
Only the script needs to be executable. Also the files are sized for 1280x1024 so if you use a different resolution you will have to change gap_y values and minimum_size values to accomodate.
Last edited by empthollow (2010-07-08 19:06:59)

Srcpac config questions

Similar Messages

Maybe you are looking for