Sreen full of vertival lines

Hello! I don't know what's going on, but when I boot up, and into a session, my screen is full of tiny vertical lines, like a gazillion. Then, it warms up, is fine now, but the wallpaper in the backround still has some purple and green ones. I hooked up an old monitor, and I got the same thing, so i know the cinema display isn't bad.Is this a software glitch, or is my 9800 pro going bad? Anyone ever see this before? Thanks in advance,
Andy

This is usually an indication that your video card is on the fritz. Esp if you get the same thing with another display.

Similar Messages

My ipad screen is full of horizontal lines

My ipad screen is full of horizontal lines & it wont switch off. Even after force close, when i restart, the lines are still there ?
What do I do ?
Regards
Sumit

First try a simple reset if you already havent. Hold down the home and power buttons for 15 to 30 seconds until you see the silver apple then let you device start normally. If the lines are still there the next step would to be backup your device and restore from iTunes as a new device. If the lines are still there after you restore your device would need service or replacement.

Accessing full 32 DIO lines on PCI-6602 in C++

Hi,
I have seen a couple of posts on this topic, but none seem to contain an answer to the question, and the documentation in the Register Level Programming Manual appears to be incomplete.
We need to access the full 32 DIO lines on the PCI-6602 card; however, only the first 8 lines (those driven by the STC) are documented. Is there any example code or further info that would allow us to use this functionality?
We are programming in C++, using the Driver Development Kit, in QNX.
Any help would be much appreciated.
Cheers,
Monte

The 32-bit digital port registers were not included in the chipobject (by mistake). The digital intput register is at offset 0x414 and the digital output register is at 0x510. To access them you can use the tAddressSpace object directly:
u32 value;
value = Bar1.readU32(0x414); // read digital 32-bit port
Bar1.writeU32 (0x510, value); // write digital 32-bit port
For configuration, use the IO_Pin_x_x_Configuration_Register registers to configure the line for input or output.
For example, to configure line 0 and 1 for input
tio->IO_Pin_0_1_Configuration_Register.setIO_Filter_0_Select (0); // no filter
tio->IO_Pin_0_1_Configuration_Register.setIO_Pin_0_Select (0); //input
tio->IO_Pin_0_1_Configuration_Register.setIO_Filter_1_Select (0); // no filter
tio->IO_Pin_0_1_Configuration_Register.setIO_Pin_1_Select (0); //input
tio->IO_Pin_0_1_Configuration_Register.flush (0);
or lines 29, 30 and 31 for output:
tio->IO_Pin_28_29_Configuration_Register.setIO_Filter_29_Select (0); //no filter
tio->IO_Pin_28_29_Configuration_Register.setIO_Pin_29_Select (2); // digital output
tio->IO_Pin_28_29_Configuration_Register.flush (0);
tio->IO_Pin_30_31_Configuration_Register.setIO_Filter_30_Select (0); //no filter
tio->IO_Pin_30_31_Configuration_Register.setIO_Pin_30_Select (2); // digital output
tio->IO_Pin_30_31_Configuration_Register.setIO_Filter_31_Select (0); //no filter
tio->IO_Pin_30_31_Configuration_Register.setIO_Pin_31_Select (2); // digital output
tio->IO_Pin_30_31_Configuration_Register.flush (0);
valid values for the select field are:
0 - input
1 - counter output
2 - digital output
I hope this helps.

Full deliveries each line item wise

Hi,
I have one sales order with 5 line items, system should allowe only full quantity deliveries each line item wise. we need to control partial deliveries each line item wise, so how can we control this. can you please guide me..
Rao

Hi,
In Customer Master (T. Code: XD02) under
TAB: Sales Area Data, and
Sub-Tab: Shipping
There is Field: Partial delivery per item,
Select Option: C - Only complete delivery allowed
This will meet the requirememnt
Best Regards,
Amit.

About vertival lines in table

HI,
I have created a table with 5 cloumn for item details invoice in main window but the line are not running untill to the end of page .if i have 2 line items when the vertical lines stops at 2 lines but,i want it upto end of page .

Hi,
If you want to display the lines until end of page Take one Template and place it on the same window which you are using for table and create the same width Columns as per table columns dimensions then provide lines to it. Then data will coming from table and lines will coming from Template. but template must be empty with only lines. Both should be on same alignment starting position.

After BB logo on startup screen full of random lines and not reacting on touch

A few days after a new screen was installed, the microphone during calls is not working anymore, except for calls using the speakerphone function or when a (audio only) headset is plugged in.
Also the screen sometimes was not reacting on touching and a restart was necessary to let it react again. Now the phone is not starting up anymore. After the blackberry logo is on screen properly, the screen fills with random lines with different pixel motives. Nothing changes when touching and also a short click on the top button does not make the screen go blanc.
I tried rebooting with up and down volume buttons pressed, but that also makes no difference. The twitter helpdesk of BB is not responding and T-Mobile staff was not able to help me either.
I hope I can find some help overhere.
Many thanks in advance!

ysg wrote:
BTW: The problems started after I updated my BB OS system last weekend.
Well, then that information could make a difference.
Upgraded to what OS?
From the main screen, swipe down from the top black bezel to Settings > About... what is the OS Version listed there?
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Statistic server full of error lines

Hello
we chaged the netowrk location of our Hana sandbox server and after these changes the following information is being written in log files with 1 min interval
exception 1: no.9002001 (StatisticsServerAsSQLClient/connection/OKAssurer.hpp:55)
SQLDBC error -10709: Connection failed (RTE:[89006] System call 'connect' failed, rc=113:No route to host). SQLState: .
exception throw location:
1: 0x00007f5943e9ae21 in StatisticsService::StatisticsServerException::StatisticsServerException(char const*, int, ltt::error_code const&)+0x10 at Exceptions.cpp:65 (libstatisticsserver.so)
2: 0x00007f5943e9fbe2 in StatisticsService::SQLDBCException::SQLDBCException(char const*, int, SQLDBC::SQLDBC_ErrorHndl const&)+0x30 at Exceptions.cpp:103 (libstatisticsserver.so)
3: 0x00007f5943e4e48e in StatisticsService::OKAssurer<SQLDBC::SQLDBC_Connection>::~OKAssurer()+0xca at OKAssurer.hpp:55 (libstatisticsserver.so)
4: 0x00007f5943e549d9 in StatisticsService::GuardedConnection::connect()+0xf5 at GuardedConnection.cpp:107 (libstatisticsserver.so)
5: 0x00007f5943e54aa2 in StatisticsService::GuardedConnectionConnector::GuardedConnectionConnector(StatisticsService::GuardedConnection&)+0x20 at GuardedConnection.cpp:158 (libstatisticsserver.so)
6: 0x00007f5943ea860b in StatisticsService::CollectorThread::run(void*&)+0x887 at CollectorThread.cpp:248 (libstatisticsserver.so)
7: 0x00007f592ebc8bb5 in Execution::Thread::staticMainImp(void**)+0x681 at Thread.cpp:457 (libhdbbasis.so)
8: 0x00007f592ebc8d5d in Execution::Thread::staticMain(void*)+0x39 at Thread.cpp:525 (libhdbbasis.so)
I can ingrore it and simply truncate log file as this is our sandbos, but maybe smb has an idea what needs to be done on Hana server. After the trace was enabled for Statistics server i got nothing actually, the same errors without reasonable explanation. There are no errors to/from hana connectivity.
We do not have have Sapcotrol up and running and red alert mark is on Overview tab available. Could that be the cause of this?

Hi
I am getting the same error. Have you found a solution yet?

How to use the second display for installation OS in my vertical lines iMac

My 17" iMac display is full of vertical lines, it is unuseable. Does anyone know how to use the second display for Mac OS X or disable the first display for installation Mac OS x ?

Go to: *System Preferences > Displays* and select the Arrangement tab, then relocate your Menu bar by dragging it to the other display.
Unfortunately there is no Hardware or Software switch to turn off the iMac's Internal Display.

Grab is not working. It's taking pictures fine, but the pictures are colored lines.

I have used Grab in the past just fine. It takes nice, big pictures of anything on my screen. Yesterday, I used grab like I normally would, and it took a picture that was the same size as what I had selected, but the picture wasn't there. It was just a bunch of black and colored thin horizontal lines. It does this for all the features...capture, selection, window, timed screen, etc. They all are full of colored lines!!! How can I fix this? I use grab a lot, so I would like to fix it ASAP!
Thanks!

Grab (or something like it) can be a very useful utility, but I'd suggest downloading the free SnapnDrag http://www.yellowmug.com/snapndrag/, which is easier to use and has equal or better functionality. I haven't had experience with Grab - but SnapnDrag will solve your issue with a download. It's a solid application that's been around for years.

Finding the full path of a process binary using /proc

Hello,
I have an application where I need to monitor whether a certain other process is running. I'm using the /proc filesystem and an ioctl call - namely, PIOCPSINFO - to fetch process information into a prpsinfo_t, then use either the pr_fname field for the base name of the process executable or pr_psargs for the full launch command line - the first argument being the executable name. However, I see that if I launch something like "man chmod" in the shell, the pr_psargs for that process is "man chmod", not "/usr/bin/man chmod", thus making it hard to distinguish between binaries which have the same base name, but can be run from different locations (e.g. /usr/ccs/bin/make and /usr/local/bin/make). Is there some way to find out the environment (actually, the PATH variable) that a process has been run with? I see there's an 'uintptr_t pr_envp' in pr_psinfo_t that is supposed to be the "address of initial environment vector". How can I use that?

I believe you have to open the processes 'map' file and use the envp address
as an index into that file. It's the address inside the target process.
The problem is that (until recent S10 release) the kernel doesn't actually
remember the pathname that was used to open the binary. There is
no guarantee that the binary is actually the first one on the search path
that's just a convention followed by most shells. If the program was
explicitly exec'ed by another program, it might not even be on the search path.
However, you can get an open file descriptior on the executable binary
by using a /proc interface.
If you know the file that you are looking for there is another way:
- open the binary you're looking for (/bin/ls)
- get device/inode of this file (using stat)
- seach processes that "look" like they might be the one you want
- for each one:
get FD of binary using /proc
stat the FD to get device/inode
compare to device/inode from the binary you're looking for
This is a bunch more work, but it's the only way to be sure.
It's better to avoid the whole mess and find a better way.
it's better to let an OS utility do the /proc mucking. They are
more likely to get it right. /proc is pretty complicated. And if you
using it ways that haven't been tested before, you can find
interesting problems.
You could just run 'ps|grep' or the 'pgrep' command.
Here is a short demo of how to compare inodes:
% ls -i /proc/$$/object/a.out
97634 /proc/9120/object/a.out <--- always called a.out, no matter the binary name
% ls -i /bin/bash
97634 /bin/bash <-- notice the same inode number
This means /bin/bash is the executable being used for my current shell.

Vertical line issue in SAP Script main window

Hi All,
I want to draw a vertical line in my main window in SAP Script output.
But problem is in main window i am printing some texts at the beggining then i am printing line items.
So this is not fixed line (box). It may increase/decrease based on text available before line items.
How can i manage this prining vertival line as i don't know height, top of this line!
Thanks in advance.
Thanks,
Deep.

Hai Deep,
Use Elements as suggested by Kodarapu.
Now goto Paragraph Formats create a format for Item lines.
ex.
Name Paragraph Format as 'IL' Now click on the Push Button "Tabs" on bottom Right.
now in "Tab Position" enter the spacing that you need for your item dispaly
ex.
Number     Tab position       Alignment
1               6.00   CH          LEFT
2               25.00 CH         LEFT
3               54.00 CH         LEFT
The above example is for 3 items
Now in your Script Windows-> Main
do the following.
/E           ITEM_LINE_A
IL           &EKPO-EBELP&,,&EKPO-EMATN&,,,,&EKPO-TXZ01&
Hope it SOlves your Issue.
Cheers,
Suvendu

Any fix for CC render issue with the new MacPro Firepro D700. Getting lines and flicker as documented in threads

Hi,
We're facing some critical problems with our new MacPros, CC, and the Firepro D700's. It appears that after we upgraded to 10.9.3 the D700's no longer work with Creative Cloud. Our Premiere renders are full of artifacts, lines, and drop out. Same issue as documented in RENDER PROBLEM - AME and Premiere Pro CC causing random horizontal lines on H.264 Renders Can you advise as to when the fix will be pushed? We have turned to "software only" render, which is killing us for time. We have a huge amount of work that goes through 4 edit bays and its putting us days behind.
Please let us know,
Sincerely, Jim Janicek
Janicek Media, Inc.
720-891-6276
[email protected]

You need to ask in Community: Premiere Pro | Adobe Community but do not expect Adobe to discuss future plans
https://www.adobe.com/cfusion/mmform/index.cfm?name=wishform for bug reports or feature requests
This forum is about the Cloud as a delivery process, not about using individual programs
If you start at the Forums Index https://forums.adobe.com/welcome
You will be able to select a forum for the specific Adobe product(s) you use
Click the "down arrow" symbol on the right (where it says All communities) to open the drop down list and scroll
Also, this is an OPEN forum, not Adobe support... please do not post personal information

My iPod touch (4) picks up my internet connection at my office and at public hotspots absolutely fine. Additionally, it shows full connectivity to my home wireless network. However, even though it shows full connectivity, it does not truly connect.

It shows full connectivity (three lines) but when I go to the app store...it just loads and loads and loads...My other devices (iPhone 4s, macBook and PC/Laptop) connect fine. I talked to apple for an hour...no solution. I talked to my Internet service provider for an hour..no solution. I tried to contact my router manufacturer but it is rather old and linksys no long provides support for this model. I reset the router factory settings. I reset the iPod from new as well as a back up. The iPod is brand new...two days old. Nothing works. My next step is to purchase a new router. Can anyone out there help?

I will get one tonight and try it...so frustrating! It was a gift for my dauighter and she was so excited to use it...but was so dissapointed We'll see! Thank you for your input...and if it does work...I will be sure to post it...because I have seen other posts and they never post their solution!

I get glitch lines on external display

Ive noticed on my last monitor and this new one too. On certain web pages or video oriented tasks. Lines show up on the screen. They flash in and out. what could this be...bad video card?
I thought going to a DVI display would help but I guess not.

I've come to a conclusion that when the video card overheats the lines come.
Reason being, I opened the lid and the lines were still there and when I tested a dvd movie on full screen the lines were there. And watching a DVD movie on my display never used to cause lines. But I don't watch many movies on my powerbook.
Before plugging in my new external display I noticed that my powerbook was set on Better Perfomance and never hit sleep mode the whole time I was at work so when I came home the Powerbook was pretty hot.
As time went on with the lid open the lines began disappearing. So I decided to keep it open and not run anything too crazy and as the Powerbook cooled the lines started disappearing.
I ran a full screen movie like a half hour later and received no lines!
And here I am this morning using my lcd for the past hour and a half on internet and again, no lines.
Hope this helps.

Line wrapping and scrolling in JPanel

Hello,
I've got an empty JPanel to which I want to add an (unknown) number of JLabels. Each JLabel has a text which is just one word. When my program is adding JLabels to the JPanel, I want it to have the same behaviour as a normal text editor: when a line is full, the next line gets filled (line wrapping).
If I just keep adding JLabels to a JPanel of a fixed size with .add(), there's no line wrapping. I tried it by giving the JPanel a fixed size, flowLayout and nesting it within a JScrollPane, but it keeps filling one long line, instead of jumping to the next one.
Any obvious solutions??
Thanks
Mark

well this depends on how your layout is build, you should post some code so we can see what your trying to do.
For example if your JPanel is the Frame's main panel, fixing a MaximumSize or PreferredSize wont have any effect, it will grow as big as you defined the JFrame size.
If you have only a JPanel with a max size of 200,300 in a JFrame with a size of 800,600, it will grow to 800,600.
You could create a BoxLayout with X axis, then insert an HorizontalStruts, insert your JPanel and another Horizontal Struts(Box.createHorizontalStrut(int width) ) to force the JPanel to be smaller than the JFrame.
I did not test this a lot, but it seams to work
import javax.swing.*;
import java.awt.*;
import java.awt.event.*;
public class Test {
public static MyFrame frame ;
public static void main(String[] args) {
    frame = new MyFrame();
    frame.show(true);
    frame.pack();
public static class MyFrame extends JFrame {
    JLabel a, b, c, d, e, f, g, h, i, j, k ;
    public MyFrame(){
      super();
      JPanel sizeLimiter = (JPanel)this.getContentPane();
      sizeLimiter.setLayout(new BoxLayout(sizeLimiter, BoxLayout.X_AXIS));
     // sizeLimiter.setPreferredSize(new Dimension(800,600));
      JPanel mainPanel = new JPanel();
      mainPanel.setLayout(new FlowLayout());
      mainPanel.setPreferredSize(new Dimension(400,300));
      mainPanel.setMinimumSize(new Dimension(400,300));
      a = new JLabel("this is sample test ");
      b = new JLabel("to demonstrate an example ");
      c = new JLabel("of simple a flow layout ");
      d = new JLabel("which is wrapping ");
      e = new JLabel("when it reaches the end ");
      f = new JLabel("of a line. ");
      g = new JLabel("Set the maximum size of the panel ");
      h = new JLabel("And it should work ");
      i = new JLabel("If it doesnt post your code so we can");
      j = new JLabel("check it out to see whats wrong ");
      k = new JLabel("sincerly yours, Jf Beaulac ");
      mainPanel.add(a);
      mainPanel.add(b);
      mainPanel.add(c);
      mainPanel.add(d);
      mainPanel.add(e);
      mainPanel.add(f);
      mainPanel.add(g);
      mainPanel.add(h);
      mainPanel.add(i);
      mainPanel.add(j);
      mainPanel.add(k);
      // Fix some "margins"
      sizeLimiter.add(Box.createHorizontalStrut(200));
      // Squeeze the panel
      sizeLimiter.add(mainPanel);
      sizeLimiter.add(Box.createHorizontalStrut(200));
    protected void processWindowEvent(WindowEvent e) {
      super.processWindowEvent(e);
      if (e.getID() == WindowEvent.WINDOW_CLOSING) {
        this.dispose();
}Regards,
Jf Beaulac

Sreen full of vertival lines

Similar Messages

Maybe you are looking for