Srp521w VPN dropping at the same time everyday

I have the latest firmware of FW:1.01.11 but everyday the last 4 days, the tunnels dropped at 5:31am and reconnects within a few minutes. There are 2 vpn tunnels, one for data and one for voice. Using 3des/sha1 with 28800 lifetime. Internet is going through the wan and voice is turned off and this workaround was used as well.
https://supportforums.cisco.com/docs/DOC-12874

This is a standard facet of most VPNs - the problem lies in your NAT router since both clients appear to come from the same IP address as far as the VPN server is concerned, and the router can't separate out the traffic.
There are a couple of solutions.
First, the built-in VPN server supports L2TP and PPTP protocols. You should be able to connect one system under each protocol, so that gets your two machines connected.
Second, you can replace your NAT router with one that supports multiple VPN clients (often termed 'VPN passthrough').
Third, setup a site-to-site tunnel so that your entire LAN is connected to the VPN (this saves you from having to run a separate VPN client on each machine, but is typically only worth it when you have more machines).

Similar Messages

Azure connections drop exactly at the same time everyday.

Hi Guys,
I wonder why all my connections to email server and NOC portal gets disconnected at the same time everyday. The connection drops and my retry logic would not get the connection back. However, the connection will be re-established after a while.
What could be the problem here. Any pointers to debug this issue will be highly appreciated.
Thank you,
AA

Hi,
Would you please share the detailed configuration of your deployment?
Did you create a VPN connection? Is that email server a on-premise server?
If it is related to Azure VPN connection, it would be better for you to contact
Azure support by submitting a billing ticket to better analyze the reason.
Best regards,
Susie
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

ASA 5505 as a SSL VPN Server and Easy VPN Client at the same time?

Is it possible to configure and operate the ASA 5505 as a SSL VPN server and Easy VPN Client at the same time? We would like to configure a few of these without having to purchase additional ASA 5505 and use a 2 device method (1 SSL VPN Server and 1 Easy VPN Client). Thanks in advance.

I don't think it is possible. Following links may help you
http://www.cisco.com/en/US/products/ps6120/products_configuration_guide_chapter09186a008068dabe.html
http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a008071c428.shtml

How to make my Labview vi program run at the same time everyday?

I have Labview vi that uses "Time Stamp Control & Indicator" on front panel to set time & date for program operation.
But, I cannot separate the Date from the Time for Start & Stop control.
I want pgm to run everyday (7days/week) at the same time (e.g. 8am to 630pm) - I don't care about the start & stop Date feature.
So, everyday I have to manually open the Control & change the date to today.
How can I make program only respond to Time start & stop?
Thanks,
jaceb

Of course rather than create yet something else that is running all the time, setup your VI to only execute for the desired amount of time, If you running windows you can use the task scheduler to launch it.
http://support.microsoft.com/kb/308569
Puts the burden on the OS and is not dependant on you starting it everytime you reboot, or having to put it in the start menu. there are options for it to run even if you are not logged onto the system.
Although not absolutely certain, I am reasonably sure that mac and linux also have something similar.
Paul <--Always Learning!!!
sense and simplicity.
Browse my sample VIs?

Why does my iPhone give me a message chime at the same time everyday?

For the last week, my iPhone 4 gives me a message chime everyday at the same time, 10:41 PM. Yet, there are no notifications, messages, badge icons, or calendar dates. I have no idea why it keeps doing this? Has anybody else come across this issue? If anybody can help out a guy who is fairly new to the iPhone it would be much appreciated. Thanks.

Nope, I've gone through the Clock, Reminders App and through my Notifications and I can't seem to find anything that has a notification for that time. I was wondering if it was something with my Cellular Network Carrier?

EA series 4500 and 6500 routers disconnecting once per day, everyday at the same time

I have had an EA4500 and EA6500 have the following problem:
I have time warner cable internet, Motorola SB6141 modem. The modem connects to an Ooma Telo. The 4500 and then 6500 are connected to the ooma.
I have this problem when the routers where placed in front of the ooma as well.
1 time per day, always at the same time, the router stops working. for both wired and wireless connections. i need to unplug the router to work. The modem and ooma continue to work, so i know there is internet getting passed from the modem to the ooma. However, the internet gets disruptted with the routers.
this must be a settings issue with the router. where everyday at the same time, maybe when timewarner changes over or something the router does not pick it up?? i dont know. i have gone through 2 routers and same identical problem.
thanks.

The DHCP lease time from your ISP might be set on that time that is why 2 routers are behaving the same way. And the routers may not be renewing the ip address successfully, that is why you are losing the internet connection. What you can do is to clone the mac address and you can do that by accessing the router page.
If you are using the linksys smart wifi interface, go to connectivity > internet settings > click on clone my pc's mac > click on apply.
You may also check this site for more information about intermittent connections with the router:
How To: Fixing Router Intermittent Connection Drops
http://www.smallnetbuilder.com/lanwan/lanwan-basics/24437-howtorouterdrops

Remote access VPN to server from outside and server reach internet on the same time

Dear,
I have problem in my ASA 5515-X , when i make Remote access VPN to servers in inside zone the internet connection disconnected in the servers, or when i have internet in servers, the remote access cant reach servers.
the configuration for server as static NAT for each server, and the connection of VPN is to another public IP but in the same subnet of NAT ip.
server1 : 10.10.10.2 nat to 5.6.7.8
server2: 10.10.10.3 nat to 5.6.7.9
server3: 10.10.10.4 nat to 5.6.7.10
VPN connection to 5.6.7.12
is there any solution for this senario, remote vpn to servers and the same time the servers have internet readability for download updates .. etc

Hi,
So it seems that the problem is with lacking a NAT0 configuration
You could modify the below configuration to match your networks/IP addresses used. In the below configuration I presume that you have interfaces "inside" and "outside".
object network SERVER-NETWORK
subnet <server network address> <network mask>
object network VPN-POOL
subnet <vpn pool network address> <network mask>
nat (inside,outside) 1 source static SERVER-NETWORK SERVER-NETWORK destination static VPN-POOL VPN-POOL
Just insert the correct address related information and change the "object" and interface names if required.
This configuration will tell the ASA that no NAT will be performed for traffic between the VPN-POOL and SERVER-NETWORK. The NAT configuration is bidirectional. With this configuration the Static NAT configurations will continue to work for the servers Internet traffic and this NAT0 configuration will be applied only to the VPN Client traffic.
Hope this helps :)
- Jouni

I have had my iPhone 4s for a few months and the battery life was really good. Then around the same time I updated to ISO6 and I dropped it on the floor and since the battery life has been poor lasting only a few hours. Does anyone know why this is?

I don't know why the battery life has just become so poor. I can listen to 1 song and lose 1/2% battery life. I had all the settings the same as before updating to ISO6 and now it just goes. I did drop it around the same time but I have a stong case so I don't see how this should effect it. If anyone knows how to fix it would be a great help because I used to love iPod but I am very dissapointed.

Internal damage from fall or loose connector. Take it to
Apple to be checked.

One SIMPLE, SIMPLE question that the answer seem to be no whre IN PLAIN ENGLISH! What do you have to do to have two of more tabs open at the same time. Just like ANY OTHER BROWSER LETS YOU DO! Ya know....so you can drag and drop things like pics etc.

For Pete's sake. This is not rocket sience. What more details do you want. I want two tabs OPEN at the same time so I can copy from one to the other or drag and drop from one to the other.

You can copy text and hover that selected text with the left mouse button down on another tab on the tab bar until that tab opens and drop the text in a text field in that tab. You need to make sure that that text area is visible because you can't scroll the page. You can also tear off that tab (temporarily) to a new window and resize them to see both windows. Move the tab back to the other window once you are done if you prefer that.

All clients drop association at the same time

We are seeing clients dropping their association with few APs all at the same time and would not connect back for several minutes (or even hours). And all of a sudden, they are start to connect back normally.
Wondering what can cause these kind of frequent client disconnects? Only a section of the building is affected and the remaining areas are fine.
Also, at times, I see the signal strength varies between Excellent and Poor within few seconds.
We are using LAPs and WiSM.
Any help would be appreiciated.
Thank you,
Mohan

Its in the 2.4 GHz band. I have observed this behavior. It works well for a day or two and suddenly a couple of APs only drop all the clients all at the same time. After few minutes (or hours) they are connect back to the APs fine.
This repeats 3 or 4 times in a week.
Thanks,
Mohan

Forefox dropped grade program and now that grade program says that I am on a different computer, private browsing turned on by itself at the same time

I was working with my online grade program snapgrades and the connection dropped when I started the program again Firefox was in private browsing mode. The grade program is set to email me if another computer accesses the program and I received a message that another computer had assessed my program at that time. I was hoping to find out what happened. I was on other web sites at the same time.

Install ClamXav and run a scan with that. It should pick up any trojans.
17" 2.2GHz i7 Quad-Core MacBook Pro  8G RAM  750G HD + OCZ Vertex 3 SSD Boot HD 
Got problems with your Apple iDevice-like iPhone, iPad or iPod touch? Try Troubleshooting 101

IPad and iPhone spontaneously drop WiFi at the same time

This happens every few days. My iPad and iPhone would always spontaneously drop my home WiFi signal at the same time. Then it would connect to it for like 2 seconds and then drop again, and that loop would then continue for a while. Reboot, closing background apps, etc. do not help.
This is very odd because it doesn't happen at school. Both of my devices work fine at school. Does anyone else have this problem on certain networks or is it just I'm unlucky as ****? All of my other devices (laptop, desktop, PS3) work just fine.
Specs
iPhone 5 iOS 8.1, iPad 4th (A6X) gen iOS 8.1

TThis is part of Apples continuity on all of the devices go to settings - FaceTime- iphone cellular calls - off

Hello. I dropped my ipad first gen from my chair, about 2 feet above the floor. The screen went black and I can't turn it on again. I have tried holding both buttons down at the same time, but nothing happens. Any help?

Hello. I dropped my ipad, first gen, from my chair to the floor. The screen went black and I can't start it again. I have tried to hold both buttons down at the same time, but nothing happens. Any help?

You will probably have to contact Apple for repair but before you do try this:
Turn your iPad upside down on your lap and give it a hard smack on the back.

Finding Both ( and ) open and closed as the same time in grep

Hi,
I have a character style I want to apply to all the () in my document.
In the GREP area, the drop down shows I can select one at a time and make the change.
Is there a way to find both at the same time regardless of how many characters are in between?
thanks
babs

Hi Rodney,
I have an update here.
Ok-so yesterday everything worked great...
Today, it's acting very weird.
I am using the same find and change GREP I used yesterday: To find the (or)
And i am changing it to the character style I made with the baseline shift change. It worked perfectly yesterday, and now it's deleting the ()????
I thought maybe the document might be corrupt, so I made a new one and tried it and this was even worse. I had a bunch of () in the file and asked it to find in the GREP [\(\)] and change to a character style I made and it told me it could not find any?
Even if I chose, document, all documents selection, story, nothing worked???
I trashed all the InDesign Prefs but still no go.
Is this GREP stuff really that buggy or do you think it is something with my software and machine? If you have never seen anything like this, then I will throw up a new forum and try to find out if outers ahve problesm with this stuff.
thanks!!
babs

Is it possible to be connected with a 3G modem for internet access and a WiFi router for printer sharing at the same time?

For our only internet access we have a 3G wireless modem. I have since purchased a WiFi printer and router to connect all the comptuters to in the house. The PCs have no problem with using both the 3G connection and the WiFi signal at the same time to print, however, the MacBook Pro will not connect to the 3G network and the router, it will drop the internet access from the modem and attempt to connect via WiFi (which has no internet access). Is there a solution that is available to remedy this? I attempted to create an adhoc printer network, however, the macbooks again will not print off of this, only the PCs. And I'm getting a bit frustrated overall with this.

The 3G wireless modem is on one of the PC's correct?
Why don't you pass the Internet through the Ethernet port to the router via Cat5 cable, then have that transmit a Wifi signal that everything else can use, then connect the printer to the router for print sharing?
You would have to turn off the wifi on the comptuer with the 3G modem as it's physically connected to the router and can't connect to the other machines as they are all connected to the router for sharing.
The Mac has the ability to pass, Internet Sharing in the System Preferences.
Do you have software for the Mac to run the 3G modem?

Srp521w VPN dropping at the same time everyday

Similar Messages

Maybe you are looking for