SRP527w Traffic stops routing when multiple PVC's are active

Hi,
I am currently experiencing two incredibly annoying bugs with the srp527w, if anyone could help me at all it would be much appreciated:
I am using firmware version 1.01.19 (004).
Problem 1:
I have my srp527w setup with the following:
PVC0 - VPI = 0 VCI = 35, this is setup with RFC1483 bridge, the interface is then added to the one and only vlan I have active on this device.
This interface is used for IGMP traffice for my providers IPTV service.
I then have PVC1 VPI=8 VCI=35, setup as PPPoE and set as my default gateway for internet traffic.
This setup works fine for a random amount of time, or until the device is rebooted, or until a change is made such as dhcp being turned on or off, which should not affect routes at all.
PVC1 will stay connected but just stop routing internet traffic at all. It is definitely set as the default route for the vlan. The router is configured with 3 VPN endpoints, I can still access these remote sites, just not the internet. PVC0 / IGMP traffic still works fine.
Problem 2:
Even though the vocie ports are on the same VLAN as my VPN endpoints, they will not register to a sip server on the VPN endpoint - an ATA will register fine if connected to the ethernet port.
Paul

Hi Paul,
Could you send me a copy of your configuration (http://192.168.15.1/admin/config.xml) please? I'm wondering if there is some issue with the way that you are associating the PVCs with your VLAN.
The second point is expected I'm afraid. It is not possible to route traffic from the internal voice ports over an IPSec tunnel.
Regards,
Andy

Similar Messages

Acrobat stops working when multiple PDFs are opened together, is this a bug?

Not sure this is the correct thread but then none of the threads are obviously the correct place for this question. I am running W7 last updated a week ago so it should be running all the correct progs and drivers. Acrobat XI Pro is Version 11.0.10, I have thought about updating to DC but I'm about to transfer the progs to my portable as I travel widely and don't currently see the point.
I have just started to notice that if I drag a single file from file manager to an open Acrobat window it opens without error but when I highlight more than one file and drag them across they open, then while the final file is displaying itself on the screen Acrobat throws a wobbly and stops working. Is this a known bug? Happens every time I open 2 files. Windows has been restarted from scratch and it still happens. Happens whether I highlight the files in file manager then <right click> Open With Adobe Acrobat XI or whether I drag the files across to an open window. Happens whether Acrobat is already open or when it is closed. Happens with more than 2 files as well.
I have noticed that file manager does take a while to display a preview of the file when the preview pane is open and thought that it might be the preview pane that is causing problems. I then closed the preview pane and opened 3 files without a problem, then opened 8 files at the same time and the programme fell apart again. Could be to do with the Microsoft File Manager but I'm interested to know if this is a common problem or not? I did a search on file opening errors in the Acrobat forum without success so am assuming it is unusual.

Thanks, seems to solve some of the problem, perhaps I need to uncheck more in this dialogue box... May be 'a' correct answer but not the complete solution. Anyway if all I need to do is uncheck a choice in a dialogue box then it must be a bug or driver incompatability as there seems to be no reason why I shouldn't be able to use 2D graphics acceleration.
Works if you highlight several PDFs in File Manager and then right click and 'Open with Adobe Acrobat', the error still occurs if I drag these files into an open instance of Acrobat beyond two files. Also seems to be more of a problem if one of the files is a 'colour document ' or 'greyscale document' scanned by Acrobat itself.

ITunes stops working when it's not the active window and connected to the internet

Hi,
I have a problem with iTunes where it crashes, only when the wifi is on and connected to a network.
Usually it occurs when I click onto another application outside of iTunes.
I've tried reinstalling both iTunes and the Apple Application Support but the problem still occurs.
I'm also on Vista if anyone has any ideas that would help?
~Jenny

Along with the audio control surface, this would be a VERY welcome feature in my opinion.
For those concerned about CPU drain, it should be possible to turn this feature on or off.
When I'm editing fluidly in FCP I do in fact leave the timeline playing whilst I go to other windows to select an effect, tweak a bit of audio or even move to a different app - there's nothing unusual about this at all.
Ultimately we all have our own ways of editing, but trust me, when you've been used to (and seen the benefit of) an NLE 'feature' you really miss it when the manufacturer chooses not to include it.
Thanks
ADAM READ
InterMedia

Adobe Reader 10.0.1 hangs when multiple PDF files are open, widespread problem, big issue

I have read that quite a few people are having this problem. I have over 3,700 computers with a growing number that are reporting problems. Has anyone else figured out a solution? Adobe needs to fix this!

Does this offer any help? - see http://forums.adobe.com/message/3913446#3913446

Only when Firefox AND Thunderbird are active/open, the desktop will NOT go to sleep

I have analysed all services, startup programs and none of these causes a NON sleep issue. Only opening Firefox: it still works (slepp modus). Only opening Thunderbird: sleep modus okay. ONLY when both are open, sleep modus will not be activated. This occurs on any 2 of my Vista, HP desktops!

Are one of them configured to not sleep?
[http://www.cnet.com/news/how-to-prevent-sleep-in-os-x/]

Effect on BW Storage Capacity when BW statistics cubes are activated

Hi..
When BW statistics(technical content) is activated, is there a large effect on the BW storage capacity? As of now we are less space in BW(available is 20 GB), I want to know how much space these technical content will occupy so that I can decide if to activate them or not.
Is there any good document which shows the sizing estimate of activating the technical content.
Thanks,
Sai.

A.H.P. and Buddhi have already provided what you need to know.
Coupe of other tidbits -
RSDDSTATAGGRDEF is the largest of the tables, as it is collecting InfoObject usage for each navigation. It gets loaded to the 0BWTC_C03 cube.
The purge of the RSDDSTAT* tables, as Buddhi mentions allows you to specify a date to purge older data. It deletes data older than the specified date from all of teh RSDDSTAT tables. The process goes thru and runs a delete query table by table. It should generall be run off hours as it can result in some rather large delete queries.
You can also run selective deletions from the statistics cubes to only retain as much history as you need there.
This stuff is all pretty granular so you have to think about how long you need to retain it. I have created a ZBWTC_C51 cube that I load summarized data to from the 0BWTC-C02 cube. I retain history in the summary cube for a long time for mgmt reporting on query volume and performance trends at a monthly time grain. This lets me reduce the amount of history I retain the more detailed cubes. It really depends on what kinds of reporting you need to provide.

VS Workflow - Erroring out when multiple records are created by same user

Hi,
I am using SP 2013. I have a visual webpart and custom sequential workflow. The webpart saves the data to a custom list and the workflow is associated to the custom list on Item creation only. In the workflow, I am breaking the role inheritance and setting
permission to specific set of users, and then the normal approval workflow happens. The whole workflow condition works fine, but if the user is raising multiple requests one after another, the workflow seems to break either in the Break inheritance or granting
permission. If the user raises only one or two requests then everything works fine.
Below are the errors which I am getting in the workflow:
Error 1:
Error: Save Conflict. Your changes conflict with those made concurrently
by another user. If you want your changes to be applied, click Back in your Web
browser, refresh the page, and resubmit your changes.
I have already checked this :
http://social.msdn.microsoft.com/Forums/sharepoint/en-US/60ab04fd-9650-427d-a48f-784bc22fae05/workflow-and-save-conflict-your-changes-conflict-with-those-made-concurrently-by-another-user?forum=sharepointdevelopmentprevious_
http://adrianhenke.wordpress.com/2010/08/20/sharepoint-error-save-conflict-your-changes-conflict-with-those-made-concurrently-by-another-user/
I have also implemented the "Reload" thing posted in the above URL. This error only happens when multiple new requests are getting raised by same user. This error does not happen if I terminate the workflow and re-start the workflow.
How to fix this?
Thanks

Hi,
Based on my understanding, you have a Visual Web Part for adding new item into a list. A workflow will be triggered when item creation in this list. Everything works
fine except when an user adds multiple items in a short period.
If this is the case, plus with the error message, a possible cause is that the SharePoint Server and the workflow engine are not functioning effectively enough to
handle the multiple request in a short time, therefore a scenario is that when there is new item being added into the database, the workflow modifies the “RoleAssignments” property of this item at the same time, this may cause a “Save Conflict” error.
As you said, “If the user raises only one or two requests then everything works fine”, a workaround is that you can disable the adding item function in Visual Web
Part forcibly in a specific period after a new item is being added by current user, it can leave some time for handling the item creation and item modification.
Or if there is a need to submit multiple items concurrently, we can organize the requests into one request, then handle this item with other custom logic in your workflow.
Thanks
Patrick Liang
Forum Support
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support,
contact [email protected]
Patrick Liang
TechNet Community Support

Enabl BGP between PE-CE when PE and CE are in same AS

We have BGP enable PE-CE setup in MPLS network. Customer A has branches with unique AS numbers.
We connected our PE routers via BGP with customer CE. Issue is Customer's Head Office AS number is equal to our AS number .
We are telecom provider having same AS for iBGP in our MPLS network.
Can you say how connect customer AS (Headoffice) with our PE router when PE and CE are in same AS

No, you cannot use it only at one side otherwise one side will try to do an iBGP peering while the other will try to do an eBGP peering. And anyway, IOS is smart enough to refuse the local-as command if the remote-as matches its local AS.

Enable BGP between PE-CE when PE and CE are in same AS

We have BGP enable PE-CE setup in MPLS network. Customer A has branches with unique AS numbers.
We connected our PE routers via BGP with customer CE. Issue is Customer's Head Office AS number is equal to our AS number .
We are telecom provider having same AS for iBGP in our MPLS network.
Can you say how connect customer AS (Headoffice) with our PE router when PE and CE are in same AS

AS Override?

How to route traffic across subnets when one NIC is a hyper-V virtual switch?

Having a bit of a problem with a hyper-V environment which does not seem to route network traffic on two different subnets between each other.
If it were a purely physical server with two NICs and a gateway set traffic would automatically be forwarded between the two different subnets.
However when one of those NICs is a hyper-V virtual switch this simple routing no-longer seems to work and no traffic gets forwarded between subnets?
Situation is:
Hyper-V server with two NICs
NIC 1 = 192.168.0/24 - main Internal company network.
NIC 2 (hyper-V virtual switch.) = 192.168.1/24 - connects to ADSL internet router
Virtualized Domain Controller.
One or two virtualiszed NICs as necessary
How then does traffic get routed between these two subnets? If RRAS has to be configured to do this where is the best place to do it, on the hyper-V host or on the virtualized domain controller?
Thanks,

Hi ,
You can create an internal virtual switch and configure an IP for it (I assume it is 192.168.1.2/24) .
After you enable RRAS in hyper-v host there will be two gateways for different subnets .
" NIC 2 (hyper-V virtual switch.) = 192.168.1/24 - connects to ADSL internet router "
The problem is here ,if these VMs need to access internet .
So , these VMs can not configure their gateway same as the IP of internal virtual switch , you may set VM's gateway as the ADSL internet router's IP meanwhile add a static route entry for every VM .
Please refer to the Syntax :
route add -p 192.168.0.0 mask 255.255.255.0 192.168.1.2
Hope this helps
Best Regards
Elton Ji
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

How to verify the routes from router when Polycom device Initiates traffic

Hi,
Could anyone please assist me in finding out the routes when Polycom device initiated traffic towards the BCS global.
1) polycom equipemnt is connected to the Internal Lan of the customer and its traversing through Router,
I checked though Ip accounting when the user initiates the traffic. (polycom device ip is x.x.x.10 and BCS global network is aa.aa.aa.0). When i checked IP accounting i found the destination ip is x.x.x.10 and source ip is aa.aa.aa.205 when user initiates traffic from Polycom device.
2) I also found the static route in router for BCS global network (aa.aa.aa.0) but when I tried to trace route to IP address (aa.aa.aa.205) the output shows:
1. * * *
2. * * *
10) * * *
Could anyone please assist me is there any other any other way to find out the routes.

Thanks, this did it for me. The verification from rommon was ok and I guess I can trust the rom even when not comparing the information with cisco webpage.

Widget stops working when second widget added

I added a twitter feed widget via adobe widget and it was working. Then I added an image cycle widget and the image cycle widget worked, but the twitter feed widget stopped showing up in the browser. Here's my code:
<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd">
<html xmlns="http://www.w3.org/1999/xhtml">
<head>
<meta http-equiv="Content-Type" content="text/html; charset=UTF-8" />
<title>CBB — Creative By Becky</title>
<link href="css/styles.css" rel="stylesheet" type="text/css" />
<script src="SpryAssets/SpryMenuBar.js" type="text/javascript"></script>
<script src="http://www.google.com/jsapi" type="text/javascript"></script>
<script src="scripts/jquery.js" type="text/javascript"></script>
<script src="scripts/twitter_search.js" type="text/javascript"></script>
<script src="scripts/jquery-1.6.min.js" type="text/javascript"></script>
<script src="scripts/jquery.cycle.all.js" type="text/javascript"></script>
<link href="SpryAssets/SpryMenuBarHorizontal.css" rel="stylesheet" type="text/css" />
<script type="text/xml">

</script>
<style type="text/css">
/* BeginOAWidget_Instance_2125523: #twitter */
                    #twitter {
          height: 200px;
          width: 200px
</style>
<style type="text/css">
/* BeginOAWidget_Instance_2559022: #slideshow */
                              #slideshow {
                                  padding: 0px;
                                        margin:0;
                              #slideshow-caption{
                                        padding:0;
                                        margin:0;
                              #slideshow img, #slideshow div {
                                  padding: 0px;
                                  background-color: transparent;
                                        -webkit-border-radius: 0px;
                                        -moz-border-radius: 0px;
                                        border-radius: 0px;
                                  margin: 0;
/* EndOAWidget_Instance_2559022 */
</style>
</head>
<body>
<div id="container">
<div id="header"><img src="images/header.png" width="900" height="150" alt="cbb - creative by becky freelance print and web designer" /></div>
<div id="logo">
    <script type="text/javascript">
// BeginOAWidget_Instance_2559022: #slideshow
                           slideshowAddCaption=false;
$(document).ready(function() {
          $('#slideshow').cycle({
                    after:                              slideshowOnCycleAfter, //the function that is triggered after each transition
                    autostop:                              false,     // true to end slideshow after X transitions (where X == slide count)
                    fx:                                        'fade,',// name of transition effect
                    pause:                              true,     // true to enable pause on hover
                    randomizeEffects:          true, // valid when multiple effects are used; true to make the effect sequence random
                    speed:                              2000, // speed of the transition (any valid fx speed value)
                    sync:                              false,     // true if in/out transitions should occur simultaneously
                    timeout:                    6000, // milliseconds between slide transitions (0 to disable auto advance)
                    fit:                              true,
                    height:                       '400px',
                    width:         '900px'   // container width (if the 'fit' option is true, the slides will be set to this width as well)
function slideshowOnCycleAfter() {
          if (slideshowAddCaption==true){
                              $('#slideshow-caption').html(this.title);
// EndOAWidget_Instance_2559022
    </script>
    <div id="slideshow">
      
      <img src="images/beach1.jpg" width="100" height="100" title="caption for image1" /> <img src="images/beach2.jpg" width="300" height="300" title="caption for image2" /> <img src="images/beach3.jpg" width="200" height="200" title="caption for image3" />
      <div title="sample title"> you can add blocks of text instead!</div>
      <img src="images/beach4.jpg" width="200" height="200" title="caption for image4" /> <img src="images/beach5.jpg" width="200" height="200" title="caption for image5" /> </div>
    
    <div id="slideshow-caption"></div>
</div>
<div id="menu">
    <ul id="crr_menu" class="MenuBarHorizontal">
      <li><a href="index.html">Home</a>      </li>
      <li><a href="#">About</a></li>
      <li><a href="#">Portfolio</a>      </li>
      <li><a href="contact.html">Contact</a></li>
    </ul>
</div>
<div id="leftcolumn">
    <div id="twitter"></div>
    <script type="text/javascript">
// BeginOAWidget_Instance_2125523: #twitter
$(document).ready(function() {
          $('#twitter').twitterSearch({
                    term: 'from%3Acreativebybecky',
                    title: 'creativebybecky twitterfeed',
                    titleLink: 'http://www.twitter.com/creativebybecky',
                    bird: true,                                                  // true or false (show or hide twitter bird image)
                    birdSrc: 'images/tweet.gif',                     // twitter bird image
                    birdLink: '',                    // url that twitter bird image should like to
                    avatar: false,                                        // true or false (show or hide twitter profile images)
                    anchors: true,                              // true or false (enable embedded links in tweets)
                    animOutSpeed: 500,          // speed of animation for top tweet when removed
                    animInSpeed: 500,          // speed of scroll animation for moving tweets up
                    pause: true,                                        // true or false (pause on hover)
                    time: false,                                                  // true or false (show or hide the time that the tweet was sent)
                    timeout: 8000,                              // delay betweet tweet scroll
                    css: {
                              a:     { textDecoration: 'none', color: '#990066', fontWeight: 'normal'},
                              container: { backgroundColor: '#000000' },
                              frame: { border: '10px solid #333333', borderRadius: '10px', '-moz-border-radius': '10px', '-webkit-border-radius': '10px' },
                              img:   { width: '30px', height: '30px' },
                              loading: { color: '#888' },
                              text: {fontWeight: 'normal', fontSize: '12px', color:'#ffffff'},
                              time: { fontSize: '12px', color: '#CCC' },
                              title: { backgroundColor: '#990066', padding: '5px 0 5px 0', textAlign: 'center', fontWeight: 'bold', fontSize: '12px'},
                              titleLink: { textDecoration: 'none', color: '#ffffff' },
                              user: { fontSize: '12px'},
                              fail: { background: '#6cc5c3 url(/images/failwhale.png) no-repeat 50% 50%'}
// EndOAWidget_Instance_2125523
    </script>
</div>
<div id="content">
    <h1>You've made it to my homepage.</h1>
    <p>That means I'm well on my way to expanding my creative portfolio beyond print design and setting foot into the world of digital. I think I'm getting the hang of it.</p>
    <p>This inaugural site, while not perfect, will showcase my progress in this new venture as well as highlight my current accomplishments. Thanks for visiting! </p>
</div>
<div id="footer">cbb — creative by becky — 2012</div>
</div>
<p> </p>
<p> </p>
<script type="text/javascript">
var MenuBar1 = new Spry.Widget.MenuBar("crr_menu", {imgDown:"SpryAssets/SpryMenuBarDownHover.gif", imgRight:"SpryAssets/SpryMenuBarRightHover.gif"});
</script>
</body>
</html>

Donna_d
Two script instances running how do you keep them from both running? I am trying to bring in a jSocial(1.0) and a Flexslider (2.1) thumbnail navigator both will not run with the other. Can you help?
Thanks
widgetgeek

WRT54G2 V1 stops routing after some simultaneous tcp connections

Hello guys, this issue with my WRT54G2:
- when i open more than 2 or 3 browser windows or anything that access internet, it stop routing
- shutdown and power up make it work again (then stops again after some simultaneous tcp connections)
- hard reset dont work
- WRT54G2 V1 Firmware Version: 1.0.04
- please help!

Adjust the MTU size of the router. To determine the value of MTU that should be set on the router, follow the link below.
Determining and setting up the correct MTU size

Adobe Stop working when I open two PDF Files.

I am using the Adobe Acrobat 11.0.03 on my desktop running win-8. The big issue for me is that the adobe just stop working, when I tried to open two PDF files at the same time. But it is fine when I just open one. So could any one give me same advise? Thank you very much.

Hi, Stacy:
I am using the Adobe Acrobat XI. Currently, it works perfectly when I only open one PDF file. If I try to open two files at the same time. the Adobe Acrobat just stop working and shows "Adobe Acrobat has stopped working".
It is so frastrating becasue I always need to open and edit multiple PDF file at the same time.
I really hope I can get some helps.
Thank you, Stacy.

Since about 2 weeks ago for no apparent reason, the internet on my iPad suddenly stopped working (when I open Safari, it says: "Safari cannot open the page because it is not connected to the Internet"), even though the Wifi icon in the top left corner sti

hi

Since about 2 weeks ago for no apparent reason, the internet on my iPad suddenly stopped working (when I open Safari, it says: "Safari cannot open the page because it is not connected to the Internet"), even though the Wifi icon in the top left corner still shows full signal. However, I noticed when I went into Wifi settings (Settings>Wifi) that there is no checkmark next to my network name (only the spinning circle icon, as if it's trying to process something). This only happens at home (I can browse the internet while connected to Wifi at university). My other Apple devices (MacBook Pro and iPhone 4S) work perfectly fine at home.
I've tried resetting my router, restarting my iPad, resetting Network Settings on my iPad, and tried following Hynes' instructions on this thread:https://discussions.apple.com/thread/2453187?start=15&tstart=0, but nothing has worked so far (although I have to admit that I found the instructions on that thread somewhat confusing, so there is a chance that I accidentally did not follow them properly).
Could someone please help? It'd be VERY much appreciated.

SRP527w Traffic stops routing when multiple PVC's are active

Similar Messages

Maybe you are looking for