SRP541W Multiple WAN configuration question

Hi all,
I have an SRP541W with two ADSL modems attached to it. Both are running bridged mode with PPPoE connections to two different ISPs, (TPG and Telstra Business Direct). The TPG connection is far cheaper, and has a much higher download limit. Sadly, if I leave the router in "load Balance" mode for the WAN, it "prefers" the Tesltra connection because it's faster. I want downloads for movies/music, Youtube, Internet Radio, etc, to go through the TPG connection. Is it possible to do this in the router, or would I need to set up a proxy server, (or some other external device/application)?

Thanks Christopher.
I had found that and tried a value of 2, then 3. When it didn't seem to make a huge difference I decided to post the question here. I've reached the download limit for this month so I will try again after the 17th.
What I was hoping for, was the ability to somehow select traffic types to go through specific connections. I used to be able to do that on the Snapgear router I had, but it died, and MacAfee in thier infinite wisdom, decided to kill that product line when they purchased the company.
Not being a router guru, and never having done the course on how to program the Cisco IOS, I chose the SRP router in the hopes it would do what I need without having to sit a course that costs 3 times as much as the router. Sadly it appears my hopes we in vain.
Rob.

Similar Messages

Multiple Oracle Configuration Question

We have a typical environment setup. I will explain it below:
Our application works in Online and Offline Mode. For Online mode we connect to Oracle 10g enterprise server and a Local instance of Access and In offline application totally works in Access.
Now we want to move away from Access and have Oracle PE instead just because we want to use stored procedure and same set of code for offline and online processing.
So a typical user machine will have a PE instance and a Oracle Client. Currently we use LDAP.ora for Configuring connections. Now i have few questions
1. How do we ensure that Oracle PE will work when we don't have network connection. Can we have like PE setup with Tnsnames.ORA
2. What can be the smallest possible package for PE.
3. Can I use one client to access both PE and Server databases.
Any help will be highly appreciated.
Thanks in advance.

Assuming the "Xcopy installation" refers to using the Windows xcopy command, can you clarify what, exactly, you are installing via xcopy? Are you just using xcopy to copy the ODP.Net bits? Or are you trying to install the Oracle client via that approach?
If you are concerned about support, you would generally want to install everything via the Oracle Universal Installer (barring those very occasional components that don't use the OUI). Oracle generally only supports software installed via the installer because particularly on Windows, there are a number of registry entries that need to get created.
You can certainly do a custom install of the personal edition on the end user machines. There are a few required components that I believe have to be installed (that the installer will take care of). I assume your customization will take the form of a response file to the OUI in order to do a silent install?
Justin

Question: Best practices for dealing with multiple AM configurations

Hello all,
I have a project using ADF Business Components and ADF Faces. I would like to set up multiple configurations for the Application Modules to support the following scenarios:
1). Local testing and debugging - using a connection defined in JDeveloper and AM Pooling turned off.
2). Testing and debugging on an application server - using a JDBC Data Source and AM Pooling turned off
3). Production deployment - using a JDBC Data Source and AM Pooling turned on.
It is no problem to create multiple AM configurations to reflect this scenario. In order for the web part of the application to use the correct configurations, the DataBindings.cpx file must specify the correct ones. I was thinking to have 3 different DataBindings.cpx files and to change the CpxFileName context-param in the web.xml file as needed.
My questions:
1). Does this make sense as an approach? It should be better than having to change a single AM configuration every time I deploy or test. Is there any easy way to keep multiple DataBIndings.cpx files in synch, given that we may add new pages from time-to-time? Alternatively, can we do some type of "include" processing to include just the dataControlUsages section into a common DataBindings.cpx file?
2). How would you manage the build-and-deploy process? For the most part, in JDev we would be using configuration #1. The only time to switch to configuration #2 or #3 would be to build an EAR file for deployment. Is this something that it would make sense to accomplish with ANT? I'm not an ANT expert at all. The ANT script would have "build-test-ear" and "build-prod_ear" targets which would swap in a correct web.xml file, recompile everything, build the EAR, then put the development web.xml file back. I'm relatively sure this is possible... comments?
3). Is there some other recommended approach?
I appreciate any insights from experience, or even just ideas or thoughts that I can test out.
Best regards,
John

Hi K,
Sorry for the long long delay in responding I've been traveling - and thanks for the e-mail tickler too...
To answer your question in short, I do think that ANT is the right way to go; there is an extra ANT task called XMLTask that I was able to download and play with, and it seems it would make this manipulation of the cpx file (or the xcfg file, for that matter) pretty straightforward. I don't have any code to post; it's just in the conceptual stage for me right now. I didn't see anything magical in JDev 11 TP3 that solved this problem for me either.
Having said all of that, it's more complicated than it might appear. In addition to the DataBindings.cpx file (stores, among other things, which AM configuration to use for each data control), it's certainly possible to programmatically access an AM (specifying the configuration either directly in the code or via a properties file/etc). I'm not sure what the most common use case for AM configurations is, but in my case, I have a Test configuration and a Prod configuration. The Test config, among other things, disables AM pooling. When I am developing/testing, I always use the Test config; in Production, I always use the Prod config. Perhaps the best way for me to do this would be to have an "Active" config and use ANT tasks to copy either Test or Prod to "Active." However, our Subversion repository is going to have a few complaints about this.
John

RV220W - port redirection/access rules with multiple WAN IPs

I've just installed a Cisco RV220W - which works fine for outbound traffic, however for inbound it seems unable to work with multiple WAN IPs.
We have a block of 6 WAN IPs assigned to us by our ISP, and I want to make use of all of them to expose certain ports on our servers to the outside world.
I've tried to do this with Access Rules (using HTTP as an example) with the following settings:
Connection Type: Inbound (WAN (Internet) > LAN (Local Network))
Action: Always Allow
Service: HTTP
Source IP: Single Address
Start: <one of the WAN IPs>
Send to Local Server (DNAT IP): <IP of the internal server>
Use Other WAN (Internet) IP Address: disabled
Rule Status: Enabled
Yet the server/port remains inaccessible.
I've tried:
rebooting the server with a power off/on again
implementing the same settings in port forwarding
triple-checking all IP addresses being used
The only way I've got it working is by changing the access rule so that it applies to any source address rather than one specific one... however that's not a solution for us as we need to use specific IP addresses for specific internal servers/ports.
The router's admin interface certainly suggests this should be possible, however making use of it seems to break all incoming access!
Any suggestions welcome.

You should be using "ANY" as the source IP, as you are publishing your internal server to the internet and internet means the request comes from any source IP (you don't know what it is, so it will be any.
Basically, you want any source IP to hit one of your WAN IPs on port 80, and then your firewall will redirect that request to the internal server's private IP address on same port 80. And when the response comes back from the internal server, the firewall will already have this translate entry in it so the reverse NAT will happen (you don't need configure this, it is default firewall feature).
I hope I have answered your question well.
Please mark as correct if you like the response.
Thanks

SRP547W, How to use multiple WAN IPs for port forwarding?

Hi folks,
We've run into some difficulty trying to take advantage of multiple WAN IPs in conjunction with the SRP547, and I'm hoping someone here can help out or at least tell us that we're going to need to buy a different router...
What we're trying to acheive is the ability to port forward from our distinct public IPs to different internal servers. Looking at the options under Port Forwarding it looks like we can only configure forwards at the "WAN interface" level, but our problem is that we can't work out how to set up separate interfaces for each of our Public IPs...
Our ISP provides us with a fully managed NTU/router with a single "Internet" ethernet port, which we can use by statically configuring IPs on our end. For this configuration this port has been directly patched to the WAN ethernet port on the SRP547W.
We have been allocated a 255.255.255.248 (/29) subnet, giving us 5 usable IPs after the ISP's gateway address is taken into account, like so:
a.b.c.208     Network Address (/29 subnet)
a.b.c.209     ISP Gateway
a.b.c.210     IP1
a.b.c.211     IP2
a.b.c.212     IP3
a.b.c.213     IP4
a.b.c.214     IP5
a.b.c.215     Broadcast Address
On the SRP we've set up the default "Ethernet WAN2" sub-interface with the following details for IP1
VLAN ID:               4088 (Uneditable)
Connection Type:       Static IP
Internet IP Address:   a.b.c.210
Subnet Mask:           255.255.255.248
Default Gateway:       a.b.c.209
The next step (I would have thought) would be to add a second sub-interface, using similar info for IP2
VLAN ID:               4000 (Chosen arbitrarily)
Connection Type:       Static IP
Internet IP Address:   a.b.c.211
Subnet Mask:           255.255.255.248
Default Gateway:       a.b.c.209
When we try to do so however we get:
Fail!
Conflict with Ether_WAN2 interface address type
I should mention at this point that we're running on firmware version 1.02.01 (023).
Any suggestions on how we can proceed?
Is there a CLI or other method of configuration that might work if the web interface won't?
Thanks,
Tim.

OK, I've seen reference to this solution before but not much in the way of details. Perhaps you can spell out how this ought to work, as the Software DMZ doesn't behave as I'd expected it to.
As before, on the SRP we've set up the default "Ethernet WAN2" sub-interface with the details for IP1 with a /29 subnet.
VLAN ID:               4088 (Uneditable)
Connection Type:       Static IP
Internet IP Address:   a.b.c.210
Subnet Mask:           255.255.255.248
Default Gateway:       a.b.c.209
We'd now like to expose a server function on IP2, let's say LAN details for this server are:
VLAN:                  3000
VLAN IP Range:         192.168.1.1/24
Server IP:             192.168.1.10
Server Port:           80
So first we turn on Software DMZ:
Status:                Enabled
Public IP:             a.b.c.211
Private IP:            192.168.1.10
WAN Interface:         Ether_WAN2
My understanding, based on what you've said, is that this should expose the whole server to external access via IP2. Unfortunately, it doesn't seem to work this way - we don't seem to have any access at all. Perhaps there's a default deny rule on the firewall?
Just to be sure, I tried creating a rule to allow HTTP traffic to the server in the Advanced Firewall page.
In Interface (WAN):    All
Out Interface (LAN):   VLAN.3000
Source IP:             0.0.0.0
Source Subnet:         0.0.0.0
Destination IP:        192.168.1.10
Destination Subnet:    255.255.255.255
Protocol:              TCP
Source Port:           Any
Destination Port:      Single:80
Action:                Permit
Schedule:              Everyday
Times:                 24 Hours
Still no dice. What am I missing?
Cheers,
Tim.

SAP-JEE, SAP_BUILDT, and SAP_JTECHS and Dev Configuration questions

Hi experts,
I am configuring NWDI for our environment and have a few questions that I'm trying to get my arms around.
I've read we need to check-in SAP-JEE, SAP_BUILDT, and SAP_JTECHS as required components, but I'm confused on the whole check-in vs. import thing.
I placed the 3 files in the correct OS directory and checked them in via the check-in tab on CMS.   Next, the files show up in the import queue for the DEV tab. My questions are what do I do next?
1. Do I import them into DEV? If so, what is this actually doing? Is it importing into the actual runtime system (i.e. DEV checkbox and parameters as defined in the landscape configurator for this track)? Or is just importing the file into the DEV buildspace of NWDI system?
2. Same question goes for the Consolidation tab.    Do I import them in here as well?
3. Do I need to import them into the QA and Prod systems too? Or do I remove them from the queue?
Development Configuration questions ***
4. When I download the development configuration, I can select DEV or CON workspace. What is the difference? Does DEV point to the sandbox (or central development) runtime system and CONS points to the configuration runtime system as defined in the landscape configurator? Or is this the DEV an CON workspace/buildspace of the NWDI sytem.
5. Does the selection here dictate the starting point for the development? What is an example scenarios when I would choose DEV vs. CON?
6. I have heard about the concept of a maintenance track and a development track. What is the difference and how do they differ from a setup perspective?   When would a Developer pick one over the over?
Thanks for any advice
-Dave

Hi David,
"Check-In" makes SCA known to CMS, "import" will import the content of the SCAs into CBS/DTR.
1. Yes. For these three SCAs specifically (they only contain buildarchives, no sources, no deployarchives) the build archives are imported into the dev buildspace on CBS. If the SCAs contain deployarchives and you have a runtime system configured for the dev system then those deployarchives should get deployed onto the runtime system.
2. Have you seen /people/marion.schlotte/blog/2006/03/30/best-practices-for-nwdi-track-design-for-ongoing-development ? Sooner or later you will want to.
3. Should be answered indirectly.
4. Dev/Cons correspond to the Dev/Consolidation system in CMS. For each developed SC you have 2 systems with 2 workspaces in DTR for each (inactive/active)
5. You should use dev. I would only use cons for corrections if they can't be done in dev and transported. Note that you will get conflicts in DTR if you do parallel changes in dev and cons.
6. See link in No.2 ?
Regards,
Marc

What could be causing my multiple response survey question to show a non-response in LMS report?

I have a 10 question survey that has been running fine and providing accurate responses in reports generated from my LMS. I made a property change to a multiple response type question that is now causing the reports to show a date/time (2003-01-01 18:00:00) response instead of the actual multiple responses the user made. The change I made to the question was to change the "Numbers property from" [ a), b), c) ] to [ 1), 2), 3) ]. This property change did not affect the reported responses for the single response questions, only the multi-response. This problem occured Using Captivate 4. I then tried using the same properties in Captivate 5.5 thinking it was a bug in CP4, but got the same results. Has anyone else run into this issue? I'm going to bring this to the attention of my LMS provider, but want to make sure CP is clean first.
Thanks,
Dave

First things first. I am not an LMS expert, so this is not about troubleshooting.
However, to ensure that your course works fine on a SCORM-compliant LMS, you can upload it to cloud.scorm.com and test it out. If the course works fine there, rest assured that it will work fine on any SCORM-compliant LMS. If your LMS team comes back with an issue after this, you can counter them with this evidence that the problem is with the LMS and not your course.
Sreekanth

How to create multiple pof configuration files for c# client

Is there a way to have multiple pof files for c# coherence client?
Can I create a file called my-pof-config.xml with the following line...
<pof-config xmlns="http://schemas.tangosol.com/pof">
<user-type-list>
<include>assembly://Coherence/Tangosol.Config/coherence-pof-config.xml</include>
<include>file://pof-config.xml</include>
and here is what pof-config.xml file look like
<?xml version="1.0" encoding="UTF-8"?>
<pof-config xmlns="http://schemas.tangosol.com/pof">
<user-type-list>
In my C# visual studio project, this is where I load my-pof-config.xml in app.config
<coherence>
<cache-factory-config>coherence.xml</cache-factory-config>
<cache-config>coherence-cache-config.xml</cache-config>
<pof-config>my-pof-config.xml</pof-config>
</coherence>
and this is what I saw in the log...
2012-02-23 14:35:35,529 DEBUG Coherence (null) - 2012-02-23 14:35:35.529 level(thread=System.Threading.Thread): Loaded POF configuration from "FileResource(Uri = file://my-pof-config.xml, AbsolutePath = D:\worktrees\ads\mainline\v2\ads\demos_cs\build\my-pof-config.xml)"
2012-02-23 14:35:35,545 DEBUG Coherence (null) - 2012-02-23 14:35:35.545 level(thread=System.Threading.Thread): Loaded included POF configuration from "EmbeddedResource(Uri = assembly://Coherence/Tangosol.Config/coherence-pof-config.xml, AbsolutePath = assembly://Coherence/Tangosol.Config/coherence-pof-config.xml)"
2012-02-23 14:35:35,623 DEBUG Coherence (null) - 2012-02-23 14:35:35.623 level(thread=ExtendTcpCacheServiceCSharp:TcpInitiator): Loaded POF configuration from "FileResource(Uri = file://my-pof-config.xml, AbsolutePath = D:\worktrees\ads\mainline\v2\ads\demos_cs\build\my-pof-config.xml)"
I don't see pof-config.xml is loaded at "Loaded included POF configuration....". How do I get around it so I can load multiple pof configuration files for c# client?

Hi,
Not sure about C# but I would suggest try removing file:// from
<include>file://pof-config.xml</include>and keep pof-config.xml and my-pof-config.xml in the same directory.
Hope this helps!
Cheers,
NJ

Multiple runtime configurations

Hi,
I'd like to set up multiple runtime configurations on a project. i.e. I want to be able to run the same java class with multiple program arguments or virtual machines. Is there any way I can do this without creating a separate project or using <target> in an ant file?
Thanks in advance for any help,
Venura

Hi Venura,
You can do this in Project Properties. On the Profiles page, click New... to create a new profile. You can change many of the runtime settings associated with the project for each individual profile.
Thanks,
Brian
JDev Team

Partial-credit scoring in multiple response and multiple hot-spot questions

Hello everyone,
I'm calling on your generosity in the spirit of the holidays to help out a noob. I would like to create matching, multiple-response and multiple-hot spot questions where the user receives credit based on the number of correct answers within the question. For example, in a matching question where there are four items; if the user gets 2 out of the four items matched correctly, I would like for him to receive 2 out of 4 points.
I understand that Captivate doesn't support partial-credit scoring of this type, but a few posts have implied that it can be done with variables. Is there anyone who can walk me through this process, or send me to a link that will walk me through it? (I've scoured these forums and tried the Cp tutorials, to no avail.) And if it's not asking too much, please make it understandable to someone who has very little experience with variables.
Thanks, and Merry Christmas.
JR
(Running CP 5 on Windows Vista)

Hello,
I did publish an article more specific on partial scoring, perhaps this could help you:
Partial scores and customized feedback
And since you are asking for more basic information, on my blog I point to some other articles to explain the meaning of variables with/without advanced actions. Feel free to have a look (there are more postings about advanced actions and links to articles over there):
Curious about variables ?
Unleash the power of variables with advanced actions
Lilybiri

Configuration question on css11506

Hi
One of our vip with 4 local servers, currently has https. the http is redirected to https.
Now, my client has problem which a seriel directories need use http, not https. some thing like. quistion:
     1. If there is any possible, I can configure the vip to filter the special directories and let them to use http not https. and rest pages and directories redirect to https?
     2. If not, I can make another vip to use same local servers, but, is possible to only limited to special directories? and with wild code? some like the directories are partially wild coded, something like, http://web.domain/casedir*/casenumber?
     3. if not on both option, is any way I can fix this problem?
Any comments will be appreciated
Thanks in advance
Julie

I run my Tangosol cluster with 12 nodes on 3
machines(each machine with 4 cache server nodes). I
have 2 important configuration questions. Appreciate
if you can answer them ASAP.
- My requirement is that I need only 10000 objects to
be in cluster so that the resources can be freed upon
when other caches are loaded. I configured the
<high-units> to be 10000 but I am not sure if this is
per node or for the whole cluster. I see that the
total number of objects in the cluster goes till
15800 objects even when I configured for the 10K as
high-units (there is some free memory on servers in
this case). Can you please explain this?
It is per backing map, which is practically per node in case of distributed caches.
- Is there an easy way to know the memory stats of
the cluster? The memory command on the cluster
doesn't seem to be giving me the correct stats. Is
there any other utility that I can use?
Yes, you can get this and quite a number of other information via JMX. Please check this wiki page for more information.
I started all the nodes with the same configuration
as below. Can you please answer the above questions
ASAP?
<distributed-scheme>
<scheme-name>TestScheme</scheme-name>
<service-name>DistributedCache</service-name>
<backing-map-scheme>
<local-scheme>
<high-units>10000</high-units>
<eviction-policy>LRU</eviction-policy>
<expiry-delay>1d</expiry-delay>
<flush-delay>1h</flush-delay>
</local-scheme>
</backing-map-scheme>
</distributed-scheme>
Thanks
RaviBest regards,
Robert

Configuration Question on local-scheme and high-units

I run my Tangosol cluster with 12 nodes on 3 machines(each machine with 4 cache server nodes). I have 2 important configuration questions. Appreciate if you can answer them ASAP.
- My requirement is that I need only 10000 objects to be in cluster so that the resources can be freed upon when other caches are loaded. I configured the <high-units> to be 10000 but I am not sure if this is per node or for the whole cluster. I see that the total number of objects in the cluster goes till 15800 objects even when I configured for the 10K as high-units (there is some free memory on servers in this case). Can you please explain this?
- Is there an easy way to know the memory stats of the cluster? The memory command on the cluster doesn't seem to be giving me the correct stats. Is there any other utility that I can use?
I started all the nodes with the same configuration as below. Can you please answer the above questions ASAP?
<distributed-scheme>
<scheme-name>TestScheme</scheme-name>
<service-name>DistributedCache</service-name>
<backing-map-scheme>
<local-scheme>
<high-units>10000</high-units>
<eviction-policy>LRU</eviction-policy>
<expiry-delay>1d</expiry-delay>
<flush-delay>1h</flush-delay>
</local-scheme>
</backing-map-scheme>
</distributed-scheme>
Thanks
Ravi

I run my Tangosol cluster with 12 nodes on 3
machines(each machine with 4 cache server nodes). I
have 2 important configuration questions. Appreciate
if you can answer them ASAP.
- My requirement is that I need only 10000 objects to
be in cluster so that the resources can be freed upon
when other caches are loaded. I configured the
<high-units> to be 10000 but I am not sure if this is
per node or for the whole cluster. I see that the
total number of objects in the cluster goes till
15800 objects even when I configured for the 10K as
high-units (there is some free memory on servers in
this case). Can you please explain this?
It is per backing map, which is practically per node in case of distributed caches.
- Is there an easy way to know the memory stats of
the cluster? The memory command on the cluster
doesn't seem to be giving me the correct stats. Is
there any other utility that I can use?
Yes, you can get this and quite a number of other information via JMX. Please check this wiki page for more information.
I started all the nodes with the same configuration
as below. Can you please answer the above questions
ASAP?
<distributed-scheme>
<scheme-name>TestScheme</scheme-name>
<service-name>DistributedCache</service-name>
<backing-map-scheme>
<local-scheme>
<high-units>10000</high-units>
<eviction-policy>LRU</eviction-policy>
<expiry-delay>1d</expiry-delay>
<flush-delay>1h</flush-delay>
</local-scheme>
</backing-map-scheme>
</distributed-scheme>
Thanks
RaviBest regards,
Robert

T530 multiple display configuration lead to errors when closing the laptop

Hello,
I have a Lenovo T530 2429CTT and I am having some trouble when trying to set up my multiple display configuration with a Lenovo ThinkPad Mini Dock Plus Series 3.
I have an external Samsung LCD monitor which is connected to the Mini Dock via DisplayPort.
I am running Win 7 Prof.
The problem I see is with an application which uses DirectX. The display looks fine in the following configuration:
- Laptop open
- External Samsung LCD Monitor on
- Display cloned so that both devices show my desktop
The issues appear when I close the laptop. I do this because in my office I only work with the external monitor so I don't need the internal display of the laptop at that moment.
When I close the laptop the following happens:
The external display gets dark for some seconds. It comes up again, gets dark and after a while (maybe 10 sec) it stays active. Sometimes I see a notification that the color scheme has changed to Win 7 basic.
Everything seems to be fine now but when looking at the DirectX based display of my application I have some problems for example with the refresh (the display looks very weird).
BTW: The laptop has an internal and an external graphic card (Internal: Intel HD 4000, External: NVIDIA NVS 5400M).
So it seems as when the laptop gets closed, the internal graphics will be turned off. Due to this the display on the external monitor also changes the settings of the graphhic card (maybe it gets turned in an energy saver state).
I was looking at many of the NVIDIA settings without any success so hopefully somebody in this forum has an idea what is happening there.
Thanks,
Andreas

Hi,
I'm trying to buy the exact same configuration.
although i cannot find this 2429CTT on lenovo site anywhere, is available for selling on a known european supplier.
and my propose is to have 2 Monitors connected, so I'll follow this inquire very closely and hold my order until then.
do you have any update on it?
just by curiosity, what about the rest? how does the PC feels to you? everything else is working?
thanks

RV042 router multiple WAN IPS assigned to different LAN IPs range

I would like to have multiple WAN IPS and assigned them to different LAN IPs. If i used the option One-to-One NAT its give me only the LAN IP 192.168.1.xxx . There is an option to specify more than one LAN IPs but its not possible to forward ports to these extra LAN IPS or to setup rules.
Is there anyway to mange this with this router. IF not what is router that will meet my requirements?

Andreas,
Unfortunately what your wanting to do will not work with the rv042. It will only allow the one to one nat rules to be applied to the default lan subnet.
You will have to use the sa500 series router which will let you do ip aliases to different lan subnet addresses.

Multiple Workspace configuration in single environment

Hello Gurus,
Just a small doubt here.
Can we have multiple workspace configured within a single environment.? If Yes, how ?
Thanks and Regards,
Saurabh

Hello Gurus,
Still looking for the answer for the same.
Thanks
Saurabh

SRP541W Multiple WAN configuration question

Similar Messages

Maybe you are looking for