SRST advice.translation-profile on voice-port drops after router reboot.
I have MGCP gateways that configured as SRST gateways too.
I have translation from internal numbers and vice verse then I use in config.
Here is the final result:
<b>
voice-port 0/0/0:15
translation-profile incoming 1
translation-profile outgoing 2
</b>
this translations work when gateway come in SRST fallback mode.
But
<b>
translation-profile incoming 1
translation-profile outgoing 2
</b>
configs drop from voice-port 0/0/0:15 when I have router reboot
You probably are using the 'ccm-manager config-server' command to download the MGCP config on registration. This is fine for basic operation, but part of the operation is that it will delete any existing voice configs. Therefore the voice port will be deleleted and this takes the translation profile along with it.
If your configuration is static and there are no changes being made on he CUCM gateway config, the easiest solution is to remove the 'ccm-manager config-server' command. Once you do this the other commands on the voice port will survive the reload since the router will no longer delete and then re-add the voice port.
If you do need the config download, you can use Embedded Event Manager (EEM) to re-add the translation profiles on the voice port after a reload. We would need a copy of your configuration to confirm the interface details to re-apply the configs against. If you want to try this option, paste your config into this posting.
Similar Messages
-
[solved] sshd comes back to port 22 after a reboot whatever the config
Hi all,
I'm a bit confused, I'vre tried to change sshd port (from 22 to 1022)
restarting sshd was ok, sshd started using port 1022.
but after a reboot, sshd goes back using port 22... I can't see anything in the journalctl logs regarding sshd failing to setup on the 1022 port..
my sshd_config file:
# $OpenBSD: sshd_config,v 1.93 2014/01/10 05:59:19 djm Exp $
# This is the sshd server system-wide configuration file. See
# sshd_config(5) for more information.
# This sshd was compiled with PATH=/usr/bin:/bin:/usr/sbin:/sbin
# The strategy used for options in the default sshd_config shipped with
# OpenSSH is to specify options with their default value where
# possible, but leave them commented. Uncommented options override the
# default value.
#AddressFamily any
#ListenAddress 0.0.0.0
#ListenAddress ::
# The default requires explicit activation of protocol 1
#Protocol 2
# HostKey for protocol version 1
#HostKey /etc/ssh/ssh_host_key
# HostKeys for protocol version 2
#HostKey /etc/ssh/ssh_host_rsa_key
#HostKey /etc/ssh/ssh_host_dsa_key
#HostKey /etc/ssh/ssh_host_ecdsa_key
#HostKey /etc/ssh/ssh_host_ed25519_key
# Lifetime and size of ephemeral version 1 server key
#KeyRegenerationInterval 1h
#ServerKeyBits 1024
# Ciphers and keying
#RekeyLimit default none
# Logging
# obsoletes QuietMode and FascistLogging
#SyslogFacility AUTH
#LogLevel INFO
# Authentication:
#LoginGraceTime 2m
PermitRootLogin no
#StrictModes yes
#MaxAuthTries 6
#MaxSessions 10
RSAAuthentication no
PubkeyAuthentication yes
# The default is to check both .ssh/authorized_keys and .ssh/authorized_keys2
# but this is overridden so installations will only check .ssh/authorized_keys
AuthorizedKeysFile .ssh/authorized_keys
#AuthorizedPrincipalsFile none
#AuthorizedKeysCommand none
#AuthorizedKeysCommandUser nobody
# For this to work you will also need host keys in /etc/ssh/ssh_known_hosts
#RhostsRSAAuthentication no
# similar for protocol version 2
#HostbasedAuthentication no
# Change to yes if you don't trust ~/.ssh/known_hosts for
# RhostsRSAAuthentication and HostbasedAuthentication
#IgnoreUserKnownHosts no
# Don't read the user's ~/.rhosts and ~/.shosts files
#IgnoreRhosts yes
# To disable tunneled clear text passwords, change to no here!
PasswordAuthentication no
#PermitEmptyPasswords no
# Change to no to disable s/key passwords
ChallengeResponseAuthentication no
# Kerberos options
#KerberosAuthentication no
#KerberosOrLocalPasswd yes
#KerberosTicketCleanup yes
#KerberosGetAFSToken no
# GSSAPI options
#GSSAPIAuthentication no
#GSSAPICleanupCredentials yes
# Set this to 'yes' to enable PAM authentication, account processing,
# and session processing. If this is enabled, PAM authentication will
# be allowed through the ChallengeResponseAuthentication and
# PasswordAuthentication. Depending on your PAM configuration,
# PAM authentication via ChallengeResponseAuthentication may bypass
# the setting of "PermitRootLogin without-password".
# If you just want the PAM account and session checks to run without
# PAM authentication, then enable this but set PasswordAuthentication
# and ChallengeResponseAuthentication to 'no'.
UsePAM yes
#AllowAgentForwarding yes
#AllowTcpForwarding yes
#GatewayPorts no
#X11Forwarding no
#X11DisplayOffset 10
#X11UseLocalhost yes
#PermitTTY yes
PrintMotd no # pam does that
#PrintLastLog yes
#TCPKeepAlive yes
#UseLogin no
UsePrivilegeSeparation sandbox # Default for new installations.
#PermitUserEnvironment no
#Compression delayed
#ClientAliveInterval 0
#ClientAliveCountMax 3
#UseDNS yes
#PidFile /run/sshd.pid
#MaxStartups 10:30:100
#PermitTunnel no
#ChrootDirectory none
#VersionAddendum none
# no default banner path
#Banner none
# override default of no subsystems
Subsystem sftp /usr/lib/ssh/sftp-server
# Example of overriding settings on a per-user basis
#Match User anoncvs
# X11Forwarding no
# AllowTcpForwarding no
# PermitTTY no
# ForceCommand cvs server
AllowUsers kamou
Port 1022
any help would be greatly appreciated.
Cheers,
kamou
Last edited by kamou (2014-10-05 22:53:17)seems like you'r right,
sshd.socket is active:
sshd.socket loaded active listening sshd.socket
I've changed the ListenStream Parameter and now it woks fine.
thanks a lot.
kamou -
How many digital voice ports can Cisco 3663 support ?
How many digital voice ports can Cisco 3662 support ?
They said "Medium complexity Codecs: 360 (E1)/288 (T1) and High-complexity Codecs: 180 (E1)/144 (T1) "in Cisco 3660 voice gateway data sheet .
But another document said you just configured 4E1 on a Cisco 3660 router .
Which one is true ?Hi,
There are some other issue except physically accepted number of voice port.
http://www.cisco.com/en/US/products/hw/routers/ps259/products_data_sheet09186a00800921ed.html
page will give you better idea. Even though you can install many voice ports into a router , there is other limits you encounter.
Bets Regards -
No non-linear under voice-port to reslove hissing on NM-HDV
Hello.
I have a trouble with 2MFT on NM-HDV.
I can hear hissing on call.
So, i had configured no non-linear under voice-port, then i can't hear any hissing.
Instead, I can hear echo on call.
How can i fix it?
Regard,
john.Hell Venky.
Thnak you for your helping.
I tried to configure based on the web site what did you told me.
But i couldn't success it to resolve echo issue.
The voice gate have 12.4(1a) on Cisco 2851.
So the solution to reslove echo doesn't fit in my case.
As i mentioned, normally i can hear noise each i talk another persion. If i stop the conversation i can't hear noise. but i started to talk again, i can hear noise each time.
Thus i tried to disable "no non-linear" parameter, i can hear echo instead noise.
So i should choice if i can hear noise or echo.
And also, i tried to change input gain and output attenuation from -6 to 14, but the each still can hear.
out voip network toplolog is below.
NEC Digital Phone---NEC PBX---Gateway---(cat6500---MSPP(WAN Area)---cat6500)---Gateway---NEC Digital Phone.
If i make a call using Normal Phone (INot Digital Phone), I can't hear noise. Whenever i can hear noise with NEC Digital Phone.
Here is the option on cisco 2851 with 12.4
2851(config-voiceport)#?
Voice-port configuration commands:
bearer-cap Specify the bear capability
busyout Configure busyout trigger event & procedure
comfort-noise Use fill-silence option
compand-type The companding type for this voice port
connection Specify Trunking Parameters
cptone Configure voice call progress tone locale
default Set a command to its defaults
description Description of what this port is connected to
disc_pi_off close voice path when disconnect with PI received
echo-cancel Echo-cancellation option
exit Exit from voice-port configuration mode
idle-detection Idle code detection for digital voice
input Configure input gain for voice
music-threshold Threshold for Music on Hold
no Negate a command or set its defaults
non-linear Use non-linear processing during echo cancellation
output Configure output attenuation for voice
playout-delay Configure voice playout delay buffer
shutdown Take voice-port offline
threshold Threshold [noise] for voice port
timeouts Configure voice timeout parameters
translate Translation rule
translation-profile Translation profile
trunk-group Configure interface to be in a trunk group
voice-class Set voiceport voice class control parameters
Please advise to me to reslove the problem.
Regard,
john. -
Confused about calling translation profile explanation In official cert guide 640-461
Hi.
On page 143 of the official ccna voice cert guide there Is an example of a translation profile where calls from the PSTN with DID range of 6xxx should be converted to 5xxx to reach the internal network.There Is an explanation of why the called rule Is used instead of the calling:
"Assigning the translation rule as a calling translation would change the caller ID of a person
calling into the organization."
I don't understand this line. Shouldn't a calling translation change the caller ID of a person calling from within the organization and not into It ?You are saying "Calling Translation" but do you mean to say "Calling Party Transformation?"
The Calling Party Transformation is relative to the direction of the call flow.
In CUCM, on a SIP trunk, in the direction of Inbound, the Calling Party is the PSTN caller calling into your organization. -
No cisco phone with voice port?
Hi
could any one advice me about "switchport voice vlan"?
I have a configuration like:
interface GigabitEthernet 1/-/1
description test phone
switch port access vlan 100
switchport mode access
switchport voice vlan 200
when I plug a no-cisco phone into this port, the phone try to get dhcp from vlan100, not vlan 200.
do I have any chance to force it go to vlan 200? o
Any comments will be appreciate
Thanks in advance
julxuHi
Most IP phones have some mechanism for setting the VLAN - Cisco phones use CDP, but other phones do not. Check with the manufacturer, or post up the type of phone you have.
For example, some phones require you to set custom DHCP options to set the VLAN.
Aaron HarrisonPrincipal Engineer at Logicalis UK
Please rate helpful posts... -
Num-exp vs translation profiles vs dial-peer
Hi friends,
This topic has been discussed many times still I couldn't find any relevant answer for the same and even configuration sometimes give unseen results.
As far as I know, following techniques exist in router for digit manipulation;
1. Number expansion
Applied globally
2. Translation profile
Applied on dial peer or PoTS interface or Controller or VoIP globally
3. Various commands found under dial peer like forward, prefix, strip digits etc.
Having all information available, I understand it fair well about independent working of all of the above techniques. But when it comes to apply all of the above techniques together, then it becomes complex which techniques apply in what order and hence not very clear to configure. I found lot of discussions on this topic and also found that Cisco has lot of contradictory information about the same in it's documents.
Will appreciate if someone can let me know in exactly which order above techniques are checked in router for both inbound and outbound call?Hi Chris,
Thanks for your time.
It's getting conflicted with what Cisco stuff says;
Following is the priority for inbound VoIP dial-peer as per Cisco stuff;
Priority 1: Global voice translation profile (applicable only for incoming call)
Priority 2: Number Expansion
Priority 3: Inbound Dial Peer Selection
Priority 4: Voice Translation Profile under Dial-Peer (I skipped CLID here purposefully)
Same is applicable for PoTS inbound call where stuff says that voice translation profile applied to PoTS interface has more priority than number expansion.
I'm comfortable with digit manipulation applied during outbound call but for incoming call, it's still not clear. What do you suggest for the above priorities?
Tomorrow I'll also try to put my hands on doing some test configuration to actually check during inbound voip call, global translation profile has more priority or number expansion?
Thanks
Vivek -
Fax Blocked Voice Port (FXS)
hi,
an outgoing fax call blocked my voice port. it stays in a busy state for days... shut and no shut doesn't put the voice port in a dorm state again, only a reload will correct it... is there any solution instead reloading the c2800?
many thanksDino -
If you are running IOS 12.4, This seems to be attributed, possibly, to a known bug with the FXS port:
Cisco bug ID CSCse83674
http://www.cisco.com/cgi-bin/Support/Bugtool/onebug.pl?bugid=CSCse83674 -
Port Translation (Non to Standard Ports)
Hi Guys
I would like some advise/ideas on the best solution for the below.
I have a application server which uses non standard HTTP/HTTPS ports.
What I want is a solution to translate these ports to standard ports.
Client 1 accesses the site on port 80 – from a gateway or something similar – the gateway accesses the application server on port 4466 etc and presents the site to the client on port 80.
I have various application servers which use non standard ports and want to create a central solution so that all three of my clients will not have to make any changes to the firewall/ proxy servers as to them they will be accessing the site on a standard port 80.
Any advise much appreciated.
Many thanks
EdThe translation is from one port to another, not many to one.
Meaning that we can't redirect all three ports to just one on the outside.
We have to use one port per IP.
Would this work if i had multiple ports ?
Only if you have multiple addresses.
Like:
Test1.com:80---internalTest1.com:4445
Test2.com:80---internalTest2.com:4456
Test3.com:80---internalTest3.com:8776
They will allow the traffic through as normal?
Yes, the clients in the outside will just go to the websites as usual, the whole process will be transparent for them. -
Unable to configure voice ports on cisco2811
I have configured the Voice Gateway and calls are working internally.
I recently installed a WIC-1B-S/T-V3 card to prepare to getting outside line access.
To try a set of Dial-Peer and put the port command , but I have been rejected.
I've confirmed that IOS Version,compatibility of WIC,PVDM is installed.
How do I get my WIC card to work?
The following is a show command.
【try set up】
R1#conf t
R1(config)#dial-peer voice 100 pots
R1(config-dial-peer)#port 0/0/0
^
% Invalid input detected at '^' marker.
R1(config-dial-peer)#port ?
<50-50> Voice interface slot #
R1(config-dial-peer)#port 50/?
<0-0> Voice interface SubUnit #
R1(config-dial-peer)#port 50/0/?
<1-20> Voice interface port # within vic
R1(config-dial-peer)#port 50/0/1
^
% Invalid input detected at '^' marker.
【show voice port summary】(i know 50/x/x voice port is automatically created.)
R1#show voice port summary
IN OUT
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
========= == ============ ===== ==== ======== ======== ==
50/0/1 1 efxs up up on-hook idle y
50/0/1 2 efxs up up on-hook idle y
-- omission --
50/0/20 1 efxs up up on-hook idle y
50/0/20 2 efxs up up on-hook idle y
【show ip interface brief】
R1#sh ip int brief
Interface IP-Address OK? Method Status Protocol
FastEthernet0/0 192.168.11.110 YES NVRAM up up
FastEthernet0/1 192.168.110.1 YES NVRAM up up
BRI0/0/0 unassigned YES NVRAM up up
BRI0/0/0:1 unassigned YES unset down down
BRI0/0/0:2 unassigned YES unset down down
Loopback0 1.1.1.1 YES NVRAM up up
【show diag】
R1#sh diag
Slot 0:
C2811 Motherboard with 2FE and integrated VPN Port adapter, 2 ports
Port adapter is analyzed
Port adapter insertion time unknown
Onboard VPN : v2.2.0
-- omission --
PVDM Slot 0:
16-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card
Hardware Revision : 4.0
Part Number : 73-8538-05
Board Revision : A0
Deviation Number : 0
Fab Version : 04
PCB Serial Number : FOC104518AZ
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Processor type : 00
Product (FRU) Number : PVDM2-16
Version Identifier : V01
EEPROM format version 4
EEPROM contents (hex):
WIC Slot 0:
BRI S/T - 3086 WAN daughter card
Hardware Revision : 1.0
Top Assy. Part Number : 800-24973-01
Board Revision : B0
Deviation Number : 0
Fab Version : 01
PCB Serial Number : FOC10515ZRK
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : WIC-1B-S/T-V3
Version Identifier : V01
【show inventory】
R1#sh inve
NAME: "2811 chassis", DESCR: "2811 chassis"
PID: CISCO2811 , VID: V01 , SN: FHK0934F0HR
NAME: "Wan Interface Card BRI S/T (3086)", DESCR: "Wan Interface Card BRI S/T (3086)"
PID: WIC-1B-S/T-V3 , VID: V01 , SN: FOC10515ZRK
NAME: "PVDMII DSP SIMM with one DSP", DESCR: "PVDMII DSP SIMM with one DSP"
PID: PVDM2-16 , VID: V01 , SN: FOC104518AZ
【show version】
R1#sh version
Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 12.4(7), RELEASE SOFTWARE (fc6)
ROM: System Bootstrap, Version 12.3(8r)T7, RELEASE SOFTWARE (fc1)
System returned to ROM by power-on
System image file is "flash:c2800nm-adventerprisek9-mz.124-7.bin"
Cisco 2811 (revision 53.51) with 247808K/14336K bytes of memory.
Processor board ID FHK0934F0HR
2 FastEthernet interfaces
1 ISDN Basic Rate interface
1 Virtual Private Network (VPN) Module
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
62720K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
【show run】
R1#sh run
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname R1
boot-start-marker
boot-end-marker
no aaa new-model
resource policy
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.110.1
ip dhcp pool VLAN10
network 192.168.110.0 255.255.255.0
default-router 192.168.110.1
option 150 ip 192.168.11.200
isdn switch-type ntt
voice-card 0
no dspfarm
interface Loopback0
ip address 1.1.1.1 255.255.255.255
interface FastEthernet0/0
ip address 192.168.11.110 255.255.255.0
duplex auto
speed auto
interface FastEthernet0/1
ip address 192.168.110.1 255.255.255.0
duplex auto
speed auto
interface BRI0/0/0
no ip address
encapsulation hdlc
isdn switch-type ntt
isdn point-to-point-setup
isdn incoming-voice voice
isdn map address .* plan unknown type unknown
router ospf 1
log-adjacency-changes
network 1.1.1.1 0.0.0.0 area 0
network 192.168.11.0 0.0.0.255 area 0
network 192.168.110.0 0.0.0.255 area 0
router ospf 12
log-adjacency-changes
ip http server
no ip http secure-server
control-plane
dial-peer voice 100 pots
destination-pattern 0T
incoming called-number .T
direct-inward-dial
call-manager-fallback
max-conferences 8 gain -6
ip source-address 192.168.11.110 port 2000
max-ephones 10
max-dn 20 dual-line
endHi,
the card which u are using supports Data .
you need to have VIC cards like VIC2-2BRI-NT/TE for Voice to work.
http://www.cisco.com/c/en/us/support/docs/voice/digital-ccs/7960-2isdn-bri-vic.html
regds,
aman -
2800 config with 4FXO VIC, voice-ports?
I'm trying to configure the voice-ports on a 2800 router with a 4 port FXO VIC and when I issue the voice-port command it only shows ports 50-50 so I use
voice-port 50/0/1 and it comes back with invalid input at marker and it points to the 50.
boot-start-marker
boot system flash flash:c2800nm-ipvoice-mz.124-4.T.bin
boot system flash flash:c2800nm-spservicesk9-mz.123-8.T8.bin
boot-end-marker
Lights on the FXO card are lit up but I do not have any cables plugged into them, am I missing something?
ThanksI'm guessing this is the info on the pvdm2?
WIC Slot 1:
2nd generation - FXO Voice daughter card (4 port)
Hardware Revision : 5.0
Top Assy. Part Number : 800-21589-01
Board Revision : E0
Deviation Number : 0-0
Fab Version : 04
PCB Serial Number : FOC092447VB
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00 -
What is the main difference between IVR session and Voice port ?
If we need 4 port for Voicemail and Auto-Attendant, we had configured 4 port of IVR session and 4 port of Voice port .
Is that correct, or only Voice port enough ?I found that shortly after my post, no change. I shut/no shut and I even reloaded the CME. Other ideas?
chrs-phx-cme#sh run int serial 0/3/0:23
Building configuration...
Current configuration : 138 bytes
interface Serial0/3/0:23
no ip address
encapsulation hdlc
isdn switch-type primary-ni
isdn incoming-voice voice
no cdp enable
end
chrs-phx-cme#sh run | sec voice-port
voice-port 0/0/0
trunk-group 1
connection plar 774
description 602.246.7607
caller-id enable
voice-port 0/0/1
trunk-group 1
connection plar 774
description 602.246.0310
caller-id enable
voice-port 0/0/2
trunk-group 1
connection plar 774
description 602.246.0954
caller-id enable
voice-port 0/0/3
trunk-group 1
connection plar 774
description 602.277.4233
caller-id enable
voice-port 0/1/0
trunk-group 1
connection plar 774
shutdown
description 602.264.1518
caller-id enable
voice-port 0/1/1
trunk-group 1
connection plar 774
shutdown
description 602.264.1705
caller-id enable
voice-port 0/1/2
timeouts call-disconnect 3
shutdown
caller-id enable
voice-port 0/1/3
no battery-reversal
shutdown
voice-port 0/2/0
timeouts ringing infinity
description Bogen Paging Adapter
voice-port 0/2/1
voice-port 0/2/2
voice-port 0/2/3
chrs-phx-cme# -
Unity 7.1 Ordering Additional Voice Ports - Thru CUWL
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin:0in;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman","serif";
mso-fareast-font-family:"Times New Roman";}
My customer has CUWL licensing and has (16) Unity(7.1) Voice Ports licensed today. Customer wants to add more Voice Ports, is this done thru the PUT tool or do I need a special part number, checked the Ordering guide, and went thru the Dynamic configurator but did not see any ordering options.
I assume it is done thru the PUT tool.My first guess, unless you just didn't mention the licensing portion of this downgrade, would be just that...Licensing:
License Files and MAC Addresses
Each license file (except for the demonstration license file) is registered to the MAC address of the network interface card (NIC) on the Cisco Unity Connection server. The license file for one server cannot be used on a second server (for example, because you want to replace the Connection server). You must obtain a replacement license file that is registered to the MAC address on the second server.
The license file can be registered to only one MAC address. If the Connection server has a dual NIC, you must either configure it for network fault tolerance, which assigns one MAC address to both NICs, or disable one of the NICs and use the MAC address for the other NIC.
When you order a license file for a dual NIC that has been configured for network fault tolerance, specify the virtual MAC address that applies to both NICs rather than the physical MAC address for either of the NICs. The license file is registered to the virtual MAC address, so the license will continue to be valid even if one of the NICs fails.
You'll need to contact [email protected] (or TAC, I suppose) and request a new license. You should be able to get a temporary license that will get the system up and running until the permanent license is issued.
Hailey
Please rate helpful posts! -
Cisco 3640 cant configure voice-ports
I've an cisco 3640 with a VWIC-2MFT-E1 network module. Can anybody tell me why i cant configure any voice-port? without able to configure voice-port, i cant assign any port for my "dial-peer voice xx pots". Anybody has any solution?
what im trying to do is sending voice data traffic to 192.168.10.1
controller E1 1/0
framing NO-CRC4
clock source line primary
channel-group 0 timeslots 1-31
interface Serial1/0:0
bandwidth 2048
ip address 192.168.10.2 255.255.255.252
ip mtu 300
encapsulation ppp
no ip route-cache
no fair-queue
no cdp enable
dial-peer voice 777 pots
destination-pattern 77T
no digit-strip
direct-inward-dial
forward-digits allI've only got this from my controller E1
Vertigo(config-controller)#?
Controller configuration commands:
channel-group Specify the timeslots to channel-group mapping for an
interface
clock Specify the clock source for a DS1 link
default Set a command to its defaults
description Controller specific description
detect Enable detection of loopback request
exit Exit from controller configuration mode
framing Specify the type of Framing on a E1 link
guard-timer Guard timer (0-20) for xcsp calls - timer duration and
accept/reject on expiry
help Description of the interactive help system
line-termination Specify the line termination for E1
linecode Specify the line encoding method for a E1 link
loopback Put the entire E1 line into loopback
mode Configure the controller mode
no Negate a command or set its defaults
shutdown Shut down a E1 link (send Blue Alarm)
tdm-group Configure DS0 group for TDM
Do i need DSP for the voice-ports? Please guide me on what more module i need to get. Thanks!!
https://supportforums.cisco.com/message/3022639;jsessionid=AF45FBC0DDB8636D70F9B526A367016F.node0 -
could somebody please advice how to stop the pages dropping ,when l go on ebay ,utube etc
could somebody please advice how to stop the pages dropping ,when l go on ebay ,utube etc
Maybe you are looking for
-
Dear All, We are getting following error while saving workbook. This has started after our migration from IBM server to HP Unix server. "Document store access caused errors in the SAP Correction System" Thanks in advance. Regards: Gaurave
-
I successfully imported my favorites/bookmarks from IE to Firefox but they show up as a subfolder called "From Internet Explorer". Since I live on the computer 8 - 12 hours a day using my favorites that's additional clicks standing in the way of gett
-
Connect to Apple TV through iphone hotspot.
My inlaws have a property where they have no land line/Adsl. They use their hotspot to connect to the internet. I was going to try to set up ATV for them and wanted to know if the iphone hotspot would suffice. Or if I could connect the iphone to a
-
Re-attaching old workflow to document library
Hello, I've recently switched my sharepoint site to a new work environment (different DNS), but my custom workflows that were associated to my document libraries are no longer "attached" anymore. They still exist in the site itself, but they can not
-
Searching for simple upload applet
I hope this is the right forum for this query I need an "upload any size file" applet. Most of the commercial ones are way overblown in features that you can't turn off. All I need is the ability to upload a file of any size, browse for the file to u