SRW2008MP - Can't access console port

Hi, I have just purchased a used SRW2008MP that I can't configure.
I suspect that the default IP Address has been changed, so I'm trying to get in via the console port.
Unfortunately, I don't have the original console cable, so I'm not sure of the port pin-out.
Can someone please confirm the 9 pin D connector pinout for me please ?
I assume that a standard straight or null-modem cable is not suitable for this purpose ?
regards
Dave

Dave,
Very nice! I have not seen a breakout box in years. I must admit, I'm a little jealous. Please be sure any adapters being used are straigh through with your VOM.
The next part of the equation is that you must set your hyperterm connection up for this device. I should have mentioned this earlier, but I certainly did not suspect you would have access to a "cable" that fast. Set your line speed for 38400 8,N,1 with no hardware flow control. Please be certain that you are using the correct COM port, and that it does in fact work.
Keep me posted,
Christopher

Similar Messages

Unable to access console port

Hi,
i was unable to access my cat6509 neither from console port or telnet access since someone by mistake has modified the setting in the switch &now it become inaccessible so is there any suggestion to workaround without losing my current configuration .
by the way when i connect to the concole port through terminal window nothing can by display in the terminal(blank)

Hi,
have you access to the MSFC?
I don't understand the problem, but this maybe could help you:
http://www.cisco.com/en/US/products/hw/switches/ps700/products_configuration_example09186a00804ceb07.shtml
HTH
Andrea

Can not access serial port while upgrading from LabVIEW 6.1 to 7.0

Hi,
I built an application under LabVIEW 6.0.2. few years ago. This application uses LabVIEW serial features. When I upgraded to LabVIEW 6.1, my application was still working correctly.
Today, I upgraded to LabVIEW 7.0, mass compile all VIs and now my application can not communicate with my peripheral !!!
The program is sending the command to the peripheral. The peripheral answers but LabVIEW serial driver does not see any datas on buffer even if datas are available ... "Bytes At serial port.vi" always returns 0. I am sure that datas are available, using a COM port psy.
Does anyone has an idea?
I saw a lot of solutions in the forum, but I would like to know the best solution with minimum work, te
st, and so on ... on my program.
Regards,
Pascal.

Hi Pascal,
Which is your version of NI-VISA?
Please see the link bellow :
http://digital.ni.com/manuals.nsf/websearch/E8D86CD680B0753D86256D2C005D8EA0
The first test to be made is to test the communication with your serial port using MAX (Measurement and Automation Explorer) :
Open MAX, Go to "Devices and Interfaces", then "Ports", select COM1 (or ASRL1::INSTR). Right clic on it and select "Open VISA Session" the go the "Basic I/O" then Write data, execute, Read data, execute.
Be sure that the communication is OK. Be sure that you use the same Alias existing in MAX in your LabVIEW program.
Now, if all is OK, try to use Serial communication examples existing in LabVIEW Help>>Examples Finder. These examples use NI-VISA VIs.
If all above is OK and you
still have the same problem, try to follow these instructions :
"In order to use the old Serial Compatibility VIs in LabVIEW 7.x, you must copy the following files from a previous version of LabVIEW to the LabVIEW 7.x directory:
Replace the serial.llb in LabVIEW 7.x with the serial.llb from a previous version of LabVIEW. This file is found in C:\Program Files\National Instruments\LabVIEW\vi.lib\instr.
Replace the _sersup.llb file in LabVIEW 7.x with the _sersup.llb from a previous version of LabVIEW. In LabVIEW 6i and 6.1 this file is located in C:\Program Files\National Instruments\LabVIEW\vi.lib\platform. In LabVIEW 7.x (and 5.x) this file is found in C:\Program Files\National Instruments\LabVIEW\vi.lib\instr.
Copy the file serpdrv to the C:\Program Files\National Instruments\LabVIEW 7.x directory. This file is not installed with LabVIEW 7.x, so it only needs to be copied from a previous version of LabVIEW, not replaced."
I hope that my answer will help you.
Sa
naa T
National Instruments

How can I access simulink electrical port in VeriStand.

My Model uses electrical ports as IOs. How can I access these ports from LabVIEW or VeriStand, as after building the dll and including it in my VeriStand project, I can access only the Simulink ports and not the Electrical ports.

Electrical ports are the PMC port blocks for Simpower system blocks.
For ex: IO Ports for NI-Mh Batteries.

Can't access to Portal Admin Console.

Hi all,
I'm working with WLP 10.2. I've created the ear-file (using maven) and deployed it on server (with Unix-system). The current application works well.
My current task is a creation portal in streaming mode. Unfortunately I can't access to Portal Admin console for resolving task. I always retrieve "Error 404 (Not found)".
As I know the admin-tools.war is responsible for Portal Admin Console. I've checked admin-tools.war is running on server (with status "Active").
I'm using the next path for running Portal Admin Console: {serverhost:port}/{context root of admin-tools}/portal.portal.
Maybe, Should I set up(correct) application.xml or weblogic.xml?
Please let me know if you have any ideas.
Thanks,
Yuriy

I think your URL is wrong, try with the following...
http://{server:port}/{name_your_ear}Admin/portal.portal
name_your_ear= The name of your Enterprise Application.
For example,
http://localhost:7001/DemosEarAdmin/portal.portal
I hope this helps

Changed RDP port to bypass University Network restriction on 3389, now can't access server at all.

I'm new to Windows Server and I recently changed the RDP port from 3389 to 3390, due to University restrictions on Port 3389 and now I can't access the server at all via RDP, the port is not blocked at my end and the server is definitely up as I can still
access my File server.
Is there any way I can fix this blunder, it's a dedicated server so I do not have access to the actual hardware, only via RDP. Do I have to reinstall? I do still have access to RescueMode SSH.
Thanks!

No, you'll simply need to logon to console and undo the regedit.
http://support.microsoft.com/kb/306759
Regards, Dave Patrick ....
Microsoft Certified Professional
Microsoft MVP [Windows]
Disclaimer: This posting is provided "AS IS" with no warranties or guarantees , and confers no rights.

I can not access the switch through the console (solved)

Hello,
I'm having a problem.
I can not access the switch through the console. The web interface is working properly.
Model: SRW224g4
Below some pictures.
The HyperTerminal settings
error:
If anyone can help me?
Thank you and excuse the bad English.

Hello Rumenigue,
It looks to me like you are using a console cable. The reason you usually see them the other way around is because with a console cable the RJ-45 end goes into the device (an ethernet jack labeled console) whereas on this switch the console port is serial itself.
Usually the serial end of the cable you have plugs into a USB to serial adapter (because most computers today don't have serial ports anymore) and that USB connection goes into your PC, creating the virtual COM port you need in HyperTerminal.
So if you get a USB to Serial adapter you could plug that from USB to the console port, or if you computer has a serial port of its own just connect a serial cable directly from the PC to the switch, then use HyperTerminal with the settings recommended above by Tom.
Hope I have helped,
Christopher Ebert
Network Support Engineer - Cisco Small Business Support Center

CUPS corrupt - can't access Print & Fax - Constant Terminal & Console msgs

While trying to get a Windows network printer to work I changed some settings in the CUPS config file (BrowseProtocols all I suspect is the problem).
Now when I try and click Print & Fax in prefs I get the eternal wheel. I can't access localhost:631 (I believe that's the proper port) anymore either.
In terminal, I receive this message about every 6-7 seconds:
Broadcast Message from root@host172.**.**
(no tty) at 13:53 PST...
Dec 10 13:53:46 host172 /usr/sbin/cupsd[303]: Unable to read configuration file
'/private/etc/cups/cupsd.conf' - exiting!
I also get this in Console:
12/10/07 1:53:16 PM com.apple.launchd[1] (org.cups.cupsd[284]) Exited with exit code: 1
12/10/07 1:53:16 PM com.apple.launchd[1] (org.cups.cupsd) Throttling respawn: Will start in 10 seconds
12/10/07 1:53:26 PM com.apple.launchd[1] (org.cups.cupsd[286]) Exited with exit code: 1
12/10/07 1:53:26 PM com.apple.launchd[1] (org.cups.cupsd) Throttling respawn: Will start in 10 seconds
12/10/07 1:53:36 PM com.apple.launchd[1] (org.cups.cupsd[288]) Exited with exit code: 1
12/10/07 1:53:36 PM com.apple.launchd[1] (org.cups.cupsd) Throttling respawn: Will start in 10 seconds
12/10/07 1:53:46 PM com.apple.launchd[1] (org.cups.cupsd[303]) Exited with exit code: 1
12/10/07 1:53:46 PM com.apple.launchd[1] (org.cups.cupsd) Throttling respawn: Will start in 10 seconds
12/10/07 1:53:56 PM com.apple.launchd[1] (org.cups.cupsd[306]) Exited with exit code: 1
12/10/07 1:53:56 PM com.apple.launchd[1] (org.cups.cupsd) Throttling respawn: Will start in 10 seconds
12/10/07 1:54:06 PM com.apple.launchd[1] (org.cups.cupsd[308]) Exited with exit code: 1
12/10/07 1:54:06 PM com.apple.launchd[1] (org.cups.cupsd) Throttling respawn: Will start in 10 seconds
12/10/07 1:54:16 PM com.apple.launchd[1] (org.cups.cupsd[311]) Exited with exit code: 1
12/10/07 1:54:16 PM com.apple.launchd[1] (org.cups.cupsd) Throttling respawn: Will start in 10 seconds
Numbers also will not start anymore which I suspect is linked because it was working fine before I messed with the CUPS config.
Please help!

Amazing, this Web! Thanks muchly, Google. And much gratefulness to the two of you in this thread, one for posting your problem and another for the fix.
On my MacBook, a bum cups.conf file was causing the ten-second throttling problem and that was (mysteriously, at least to me for the last few days) preventing Parallels Desktop from successfully starting up! I went round and round on this until I found the messages on the console and tried going back to the original conf file.
Cheers.
+ Michael

I have moved from a G5 Powermac to an Intel Mac Pro and am porting over Items from a Backup HDD. How can I access and use drawings and documents created on the PC computer on the Intel computer ?

I have moved from a G5 Powermac to an Intel Mac Pro and selectively porting over items from a backup hard drive.
How can I access and use documents and drawings created on the PC based computer ?

Clarisworks, you need Appleworks, which will only work with Mac OS X10.6.8 or earlier. See this tip if you must go newer. Mac Pros with newer hardware configuration than July 20, 2011 can't use Mac OS X 10.6.8 or earlier without this tip and then it would be Mac OS X Server. I'm not sure if the new black Mac Pro supports that configuration or not.
iPhoto, there is an iPhoto for all versions of Mac OS X.
iTunes, there is an iTunes for all versions of Mac OS X. Note with iTunes versions 11 and later, which are needed for syncing with iOS 7 or or later, you will lose coverflow, if you liked that feature. Sadly you can't run an older version of iTunes from within Mac OS X 10.9 or later.
Sketchup: http://help.sketchup.com/en/article/60107 shows the versions that will work with intermediate Mac OS X versions, and this shows the latest version: http://help.sketchup.com/en/article/36208 be sure to click on the operating system you choose to use.
GIF - Viewing GIFs Apple's Preview can do that. Editing them, I like http://www.lemkesoft.com/ Graphicconverter.
DMG is able to be opened by all versions of Mac OS X. This are just "disk images" which store programs on a virtual disk that will open when double clicked. Frequently you'll find the installer of the said program inside. To find out if the program itself is compatible with 10.7 through 10.9, see http://www.roaringapps.com/
Otherwise see the resources on:
https://discussions.apple.com/docs/DOC-2455
If you end up deciding to stick with Snow Leopard.

HT3576 how can i verify that the network or firewall is not blocking access to port 5223.

how can i verify that the network or firewall is not blocking access to port 5223?

Talk to someone who knows something about networking and/or firewalls on an appropriate forum.
Configuring your network and/or firewall is beyond the scope of this forum, which is devoted to issues using the iPhone.

Can air for html/ajax accessing serial port or usb?

I just have made use of Adobe AIR .I want to use printer with
air . Do air have some poperties to accessing serial port or usb?
I look up that on the Adobe AIR documents.I only found
'Adobe® AIR™ provides the eans to check for changes to
the network connectivity of the computer on which an AIR
application is installed'.
Do you have some demo with Adobe AIR accessing serial port or
usb ?
Or has another poperties to do that!
thank you!!

There is no API for accessing the serial port. USB devices
can only be accessed through the file system (and only if they are
storage devices).

Can't access my Directory Server using the Console installed on a machine

can't access my Directory Server using the Console installed on a remote server, lookied into knowledge base article 4693, but still same any idea ?

I too am having problems accessing Directory server from Netscape Console installed on Winxp.
If I try to open Directory server it doesn't give any error. No windows nothing.
If I try th same from the machine on which it is installed everything is fine. What is strange is that it did open a couple of times. But at the same time I can open the admin server, Netscape Messaging server from the xp box. Searching all over for a solution. Any help/pointers would be greatly appreciated.
Config details:
iDS4.13, iMS 5.0, running on Sol 8 box
Netscape Console 4.2 on WinXP.
Thanks

Help on accessing 2900 console port

I dug up an old 2900 and forgot how to link my pc to the console port to initiate an ip address, etc. Does anyone remember?

Hello,
basically, you just need a rolled cable (pins 1 thru 8 reversed) with a DB-9 adapter, in order to connect the cable to the COM port of your PC. You can use Hyperterminal with the following settings for the COM port:
- 9600 baud
- 8 data bits
- 1 stop bits
- no parity
Check the following document:
Connecting a Terminal to the Console Port on Catalyst Switches
http://www.cisco.com/en/US/products/hw/switches/ps700/products_tech_note09186a008010ff7a.shtml
Also, you might want to install a newer version of Hyperterminal:
HyperTerminal Private Edition version 6.3
http://www.hilgraeve.com/htpe/index.html
HTH,
GP

I can not access the console reports the ESSO

I configured the console reports the ESSO but I can not access, I set the permissions on the database to access and still can not access, can someone tell me how to do these steps.
----------------------------------ERROR------------------------------------
[Async_ExceptionOccurred]
Arguments:
Debugging resource strings are unavailable. Often the key and arguments provide sufficient information to diagnose the problem. See http://go.microsoft.com/fwlink/?linkid=106663&Version=4.0.50524.0&File=System.dll&Key=Async_ExceptionOccurred
at System.ComponentModel.AsyncCompletedEventArgs.RaiseExceptionIfNecessary()
at Reporting.PLXReportService.LogonCompletedEventArgs.get_Result()
at Reporting.ReportService.logonCallback(Object sender, LogonCompletedEventArgs e)
at Reporting.PLXReportService.PLXReportServiceClient.OnLogonCompleted(Object state)
Thanks.
Edited by: JLK on Oct 4, 2011 1:48 PM

Hi
U need to login to the reporting web console with a local SQL user account. Will not work with a Windows domain account.
Also need to ensure steps in Pg 10 of DBConfig guide is completed to enable "local system" account to access db.

I can't access my IMAP port remotely. Why?

I can't access my IMAP port remotely. Why?
<p>
If you can access your IMAP port using telnet on the host, but not
remotely, this is most likely a DNS issue. IMAP is different from POP
and SMTP in that it does a DNS search. Check the DNS Service
Search Order, and delete any entries that are questionable
(i.e. an ISP that may not be reachable) and try connecting again.

Please provide a little more information. What exactly are you trying to do? Bluetooth on iOS devices is not set up to share files and photos. If you can tell us what you want to accomplish we can tell you how to do it.

SRW2008MP - Can't access console port

Similar Messages

Maybe you are looking for