SSC-400 / SSC-600 / IPsec SPA resets during SSO

Hello,
I want to know if there is any way we can overcome the restrictions on these cards, resulting in reload when an SSO happens on a Catalyst 6500 switch.
Restrictions:
>VSPA state information is not maintained between the active and standby supervisor engine during normal operation. During a supervisor engine switchover in an SSO environment, the VSPA will reboot.
>The Cisco 7600 SSC-400 is not Route Processor Redundancy Plus (RPR+) or Stateful Switchover (SSO) aware. As a result, the Cisco 7600 SSC-400 will reset if RPR+ or SSO is configured.
http://www.cisco.com/en/US/docs/interfaces_modules/shared_port_adapters/configuration/7600series/76ovwvpn.html#wp1108766
http://www.cisco.com/en/US/docs/interfaces_modules/services_modules/vspa/configuration/guide/ivmovw.html#wp1051863
Regards,
Akhtar

Hi Sung,
Have you load the appropiate FPD image into the flash? Please find the following document for more info:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/ios/12.2SX/release/notes/ol_14271.html#wp2430389
HTH,
jerry

Similar Messages

7600 SSC-400 / SSC-600 Design Limitation

Hello,
I want to know if there is any way we can overcome the restrictions on these cards, resulting in reload when an SSO happens on a Catalyst 6500 switch.
Is there any new or upcoming model of SSC cards which will be SSO aware ?
Restrictions:
>VSPA state information is not maintained between the active and standby supervisor engine during normal operation. During a supervisor engine switchover in an SSO environment, the VSPA will reboot.
>The Cisco 7600 SSC-400 is not Route Processor Redundancy Plus (RPR+) or Stateful Switchover (SSO) aware. As a result, the Cisco 7600 SSC-400 will reset if RPR+ or SSO is configured.
http://www.cisco.com/en/US/docs/interfaces_modules/shared_port_adapters/configuration/7600series/76ovwvpn.html#wp1108766
http://www.cisco.com/en/US/docs/interfaces_modules/services_modules/vspa/configuration/guide/ivmovw.html#wp1051863
Regards,
Akhtar

Hello,
You will need both. The 7600-SSC-400 is the carrier module of the SPA-IPSec-2G.
There is more information on this via the following link:
http://www.cisco.com/en/US/docs/interfaces_modules/shared_port_adapters/configuration/6500series/76ovwvpn.html
Warm Regards,
Rose

VPN service module choice 7600-SSC-400 vs. SPA-IPSEC-2G

Need to decide between the two VPN service module: 7600-SSC-400 and SPA-IPSEC-2G for a 6509 sup 720 3bxl. Not sure what is the difference and couldnt find too much info just searching the internet. What would be the benefits of one or another?

Hello,
You will need both. The 7600-SSC-400 is the carrier module of the SPA-IPSec-2G.
There is more information on this via the following link:
http://www.cisco.com/en/US/docs/interfaces_modules/shared_port_adapters/configuration/6500series/76ovwvpn.html
Warm Regards,
Rose

Problem with installing new line card 7600-SSC-400

Hi all,
I have a trouble when trying to install new line card 7600-SSC-400 on Cisco 6509. Here was the message displays on the screen after I finished installing the line card : "%C6KPWR-SP-4-UNSUPPORTED: unsupported module in slot 7, power not allowed: The image for the card is not bundled in image." I tried to install this line card on another slot, but it doesn't work. The attched item is logfile which I saved in the installing session. I don't know what I hvae to do now, please help me to resolve this problem !
Thanks so much,
Hieu

Hi Hieu,
You might want to run the following to see more detail of the error:
show diagnostic result module all detail
And I would also suggest that you reseat the 7600-SSC-400 line card firmly back to the switch, and check the status again.
If it's still showing the error, maybe you can try seating the module on a different slot, and check if you have the same issue.
If the issue still persist after reseating and testing it on different slot, then it might be a hardware issue, and you might want to open a TAC case to further investigate it.
Hope that helps.

Charge iPad suddenly resets during use. Why would this be?

It does this often and is so frustrating. Thanks!

You're initial question and description are a little confusing so to would help if you would actually explain what is going on.
"Charge iPad suddenly resets during use", does not make any sense to me anyway. So without knowing exactly what that means, why it does it is really difficult to answer. Maybe it's just a typo on your part, but it needs a little clarification.

T510 keeps resetting during boot unless started in safe mode first

This is an odd, and annoying, one. As of about 3 months ago, my aging T510 started resetting during the boot and startup process, usually while the initial Windows loader was still running, but sometimes it would get beyond that to the Windows startup screen before resetting. When it does so, it's with an audible click, and then it goes right back to BIOS boot. It has been getting steadily worse to the point that it can take up a dozen tries before it manages to complete startup. Once it has succeeded in doing so, it seems to be stable. However, if it goes to sleep or hibernates (manually or on low battery), it has the same problem trying to wake up. However, if I start up in safe mode, and then restart normally, it comes up OK every time. After a safe mode startup, if it has been off for a short time (one or two minutes), it will still start up OK. However, if it has been off for several hours, then the problem reappears.
It seems like some piece of hardware on the motherboard isn't initialising properly on powerup, but starting Windows in safe mode seems to sort it out.
My machine is a T510 4313-CTO, bought in March 2010.
Can anyone figure out specifically what's happening, and, more importantly, is it fixable?

OK, I spoke too soon. Started it up this morning (in normal mode), and it reset again, so I restarted in safe mode, and looked at the Network Adapter list in device manager, an lo and behold all the WAN devices that disappeared after I disabled them then re-enabled them yesterday had reappeared, so I disabled them again, and restarted. This time as before, it restarted OK. The devices listed were:
1394 Net Adapter
Bluetooth LAN Access Server Driver
Bluetooth LAN Access Server Driver - Packet Scheduler Miniport*
Direct Parallel*
Intel(R) 82577LM Gigabit Network Connection
Intel(R) 82577LM Gigabit Network Connection - Packet Scheduler Miniport*
Intel(R) Centrino(R) Wireless-N 1000
Intel(R) Centrino(R) Wireless-N 1000 - Packet Scheduler Miniport*
Keith & Koep USB Remote NDIS Network Device - Packet Scheduler Miniport*
Tom Tom - Packet Scheduler Miniport*
WAN Miniport (IP)*
WAN Miniport (IP) - Packet Scheduler Miniport*
WAN Miniport (L2TP)*
WAN Miniport (PPPOE)*
WAN Miniport (PPTP)*
The devices marked * were hidden after successfully restarting in normal mode, although before they showed no yellow "!" before, which is the usual reason for showing normally hidden devices.
All the Packet Scheduler Miniport entries were apparently due to the QoS Packet Scheduler driver which is installed on Windows LAN port by default, although it's rarely useful (see http://forums.speedguide.net/showthread.php?190110-Qos-Packet-Scheduler for some background). Anyway, though I tried uninstalling it (which got rid of all the Network Adapter devices followed by " - Packet Scheduler Miniport"), it still didn't cure the problem.
That was solved following Les Bell's advice at http://securitasdato.blogspot.co.uk/2011/05/infamous-packet-scheduler-miniport.html concerning correcting the driver version numbering in the registry (I had exactly the same error). Searching through the registry in the way he suggests is a bit of a faff. I found all the relevant entries under the key HKLM/SYSTEM/CurrentControlSet/Control/Class/{4D36E972-E325-11CE-BFC1-08002bE10318} (and the same under the numbered control sets). All the usual caveats apply, i.e. don't edit your registry unless you *REALLY* know what you're doing, at your own risk, etc.

Palm resets during Hotsync of Package Installer

Today, my Treo 755p started resetting during Hotsync, specifically the "Package Installer" step. If I uncheck Package Installer, Hotsync works fine. I'm using version 6.2.2 of the Palm Desktop with Vista. On my computer, the Package and Install folders are both empty. I did install some files a couple days ago, but sucessfully hotsynched after the installation.
I also tried to sync on another computer that I hotsync to only occassionally, and the same thing happened, suggesting the problem is on the Treo itself. I was hoping I could resolve this problem without a hard reset, as it seems my Treo isn't quite 100% as before the reset.
Any suggestions?
Post relates to: Treo 755p (Verizon)

Try a 10 second soft reset by taking out the battery for at least 10 seconds. This allows the device to power off completely, like a shutdown on a PC.
If that doesn't work, try renaming the backup folder on the PC in your username folder to backup.old. After the rename, sync the Treo and esee if you get the same error. If you do, you will need to hard reset the Treo.
Click on the following link to the kb.palm.com webpage for the article regarding find your device's User Folder on your desktop computer.
http://www.palm.com/cgi-bin/cso_kbURL.cgi?ID=26674
For reference purposes, click on the following link for the support page for your device on the kb.palm.com webpage.
http://www.palm.com/us/support/treo/treo755pverizon/
There are links on the page to the user guide, troubleshooting, how to's, downloads, etc.
Post relates to: Palm i705

IPSec VPN Resets before Isakmp Lifetime Expires

Hi,
I have a IPSec tunnel between ASA5520 and 1841. The ISAKMP lifetime is set to the default 24 hours on both end. No volume limit is configured. But the tunnel resets itself 1.5 hours ahead every day. I need to keep the resetting at night so that my special application won't be broken during work hours.
I thougt the premature resetting was due to IOS version on the router. I upgraded to a new version but did not fix the problem.
Besides the resetting, everything else is working fine.
Any ideas are appreciated.

Hi,
One on my logs in ASA is as follows. (IP address is modified.)
Apr 16 2009 00:52:16: %ASA-4-113019: Group = ABC.ABC.177.202, Username = ABC.ABC.177.202, IP = NZ_Router, Session disconnected. Session Type: IPSecLAN2LAN, Duration: 22h:48m:33s, Bytes xmt: 983291523, Bytes rcv: 982279579, Reason: Idle Timeout
Apr 16 2009 23:40:50: %ASA-3-713902: Group = ABC.ABC.177.202, IP = ABC.ABC.177.202, Removing peer from peer table failed, no match!
Apr 16 2009 23:40:50: %ASA-3-713902: Group = ABC.ABC.177.202, IP = ABC.ABC.177.202, Removing peer from peer table failed, no match!
Apr 16 2009 23:40:50: %ASA-4-713903: Group = ABC.ABC.177.202, IP = ABC.ABC.177.202, Error: Unable to remove PeerTblEntry
Apr 16 2009 23:40:50: %ASA-4-113019: Group = ABC.ABC.177.202, Username = ABC.ABC.177.202, IP = NZ_Router, Session disconnected. Session Type: IPSecLAN2LAN, Duration: 22h:48m:32s, Bytes xmt: 751281811, Bytes rcv: 1447481492, Reason: User Requested
The disconnection reason can be either 'User Requested' or 'Idle Timeout'. When 'Idle Timeout', the application won't get dropped; when 'User Requested', the application gets dropped.
Thanks.

Restart or reset during OSD Windows 7 on Hyper-V VM

Got started with SCCM 2012 and WDS.
The VM boot into Windows PE until a certain point.
I got passed pressing F12 and windows loading files (boot.ett00015.wim),
Then System Center 2012 Configuration screen appeared and the initializing Windows PE.
Last message I read there was "preparing network connections" and than the VM got reset.
Can anyone tell me what to look for, or mayby you had a similar problem.
Thanks for your reply

Yes I can ping the MP and took a look at the smsts.log file.
But I can't ping the VM and make a share to copy the smsts.log file.
The log shows an error when trying to get information from http://<FQDN>/sms_mp/.sms_aut?mpcert and return error code 400
tried to connect to http://<FQDN>/sms_mp/.sms_aut?mpcert, http://<FQDN>/sms_mp/.sms_aut?mplist and http://<FQDN>/sms_mp/.sms_aut?mplist1 from a random server and they all returned valid data.
So, It looks like only during the WIN-PE boot the process is not able to connect to http://<FQDN>/sms_mp/.sms_aut?mpcert.
Any suggestions?

USB Drive Resets during file copy, interrupting file operations

Fresh Arch Linux install, working USB thumb drive (Windows, previous Arch Linux setups, etc.), formatted FAT32.
Seems to randomly reset, eject, and auto-re-mount during extensive file operations (i.e. copying 4gb worth of 800 files from the USB thumb drive to disk).
I've tried various USB ports to no avail; no external hub being used.
Thoughts? Not sure where to begin diagnosing:
dmesg:
usb 1-1: configuration #1 chosen from 1 choice
scsi17 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 15
usb-storage: waiting for device to settle before scanning
scsi 17:0:0:0: Direct-Access OCZ RALLY2 1100 PQ: 0 ANSI: 0 CCS
sd 17:0:0:0: Attached scsi generic sg2 type 0
usb-storage: device scan complete
sd 17:0:0:0: [sdb] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
sd 17:0:0:0: [sdb] Write Protect is off
sd 17:0:0:0: [sdb] Mode Sense: 43 00 00 00
sd 17:0:0:0: [sdb] Assuming drive cache: write through
sd 17:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sd 17:0:0:0: [sdb] Assuming drive cache: write through
sd 17:0:0:0: [sdb] Attached SCSI removable disk
usb 1-1: reset high speed USB device using ehci_hcd and address 15
sd 17:0:0:0: [sdb] Unhandled error code
sd 17:0:0:0: [sdb] Result: hostbyte=0x07 driverbyte=0x00
end_request: I/O error, dev sdb, sector 7589504
sd 17:0:0:0: [sdb] Unhandled error code
sd 17:0:0:0: [sdb] Result: hostbyte=0x07 driverbyte=0x00
end_request: I/O error, dev sdb, sector 7589744
sd 17:0:0:0: [sdb] Unhandled error code
sd 17:0:0:0: [sdb] Result: hostbyte=0x07 driverbyte=0x00
end_request: I/O error, dev sdb, sector 7589776
usb 1-1: USB disconnect, address 15
FAT: bread failed in fat_clusters_flush
FAT: FAT read failed (blocknr 3805)
FAT: Directory bread(block 24147944) failed
FAT: FAT read failed (blocknr 3818)
<snip lots of repeats>
FAT: FAT read failed (blocknr 4032)
FAT: bread failed in fat_clusters_flush
FAT: bread failed in fat_clusters_flush
FAT: bread failed in fat_clusters_flush
usb 1-1: new high speed USB device using ehci_hcd and address 16
usb 1-1: configuration #1 chosen from 1 choice
scsi18 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 16
usb-storage: waiting for device to settle before scanning
scsi 18:0:0:0: Direct-Access OCZ RALLY2 1100 PQ: 0 ANSI: 0 CCS
sd 18:0:0:0: Attached scsi generic sg2 type 0
usb-storage: device scan complete
sd 18:0:0:0: [sdb] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
sd 18:0:0:0: [sdb] Write Protect is off
sd 18:0:0:0: [sdb] Mode Sense: 43 00 00 00
sd 18:0:0:0: [sdb] Assuming drive cache: write through
sd 18:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sd 18:0:0:0: [sdb] Assuming drive cache: write through
sd 18:0:0:0: [sdb] Attached SCSI removable disk
lsusb -v for the drive:
Bus 001 Device 016: ID 0325:ac02 OCZ Technology Inc ATV Turbo / Rally2 Dual Channel USB 2.0 Flash Drive
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0325 OCZ Technology Inc
idProduct 0xac02 ATV Turbo / Rally2 Dual Channel USB 2.0 Flash Drive
bcdDevice 11.00
iManufacturer 1 OCZ Technology
iProduct 2 RALLY2
iSerial 3 AA04012700275633
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 300mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk (Zip)
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 255
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 255
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Last edited by lieut_data (2009-12-26 17:39:56)

Jithin wrote:
When ever I copy some files or create a file in my external USB drive which is a FAT32 one. file permissions are not preserved.
From <http://support.apple.com/kb/HT3764>:
"The MS-DOS (FAT32) file system format does not support permissions, file owners, and groups. Such permissions are synthesized on Mac OS X with some default permissions. Because of this all files will have the same permissions […]"
So it's not "how it work in mac", but it's a limitation of the FAT32 file system.

Mountain Lion 10.8.2 reset during apps update (iPhoto 9.4, Aperture 3.4.1, Xcode)

I'm experiencing a lot of troubles, after Mountain Lion automatic update.
system during apps update such as iphoto 9.4, Aperture, etc, freeze, screen become white, then retart automatically.
Even today during my new iphone 5 installation made the system reset by itself. Quiet unusual for a Mac, especially this new Retina display.
My configuration,
Mac Book Pro Retina Display 15" - i7 2,6 - 16GB Ram, 768 Gb SSD
Intel HD4000
Nvidia GT M650
Can anybody help me to get out of this big issue? FYI, I rein stalled Mountain Lion manually, downloading the file from Apple website.
Thanks
Steve8869

Welcome to Apple Support Communities
http://support.apple.com/kb/HT3964

Network connection reset during download of a season. Now one episode won't work.

I bought a season of Entourage and during the download the "network connection was reset." Now one of the episodes won't play right, eg. there is green stuff on the screen during the part that works and it won't even play past about 8 minutes. Is there anything I can do to have this fixed?

I'd report the problem to the iTunes Store.
Log in to the Store. Click on "Account" in your Quick Links. When you're in your Account information screen, go down to Purchase History and click "See all".
Find the item that is not playing properly. If you can't see "Report a Problem" next to the item, click the "Report a problem" button. Now click the "Report a Problem" link next to the item.

[SOLVED] Console Font Gets Reset During Boot

I've recently switched to Arch Linux and am quite happy with it. I've never had so much fun with Linux until a friend recommended Arch. I have since installed it on both my MacBook Pro and Mac mini. Everything has been pretty smooth, but I do have one issue.
During the boot process, the system starts up with its default console font, per the usual. I have edited /etc/vconsole.conf to set the font to Lat2-Terminus16 and to set the keyboard layout to Dvorak. Here's my current config:
KEYMAP=dvorak
FONT=Lat2-Terminus16
Part-way through the boot process, the font switches to use the new font. So far, so good. Shortly after, however, the screen gets cleared and continues to produce normal kernel messages until the screen is cleared once again and presents the boot prompt, but with the default console font as opposed to the font in vconsole.conf. I am able to re-set the font again by using the setfont command, but this is a bit of an inconvenience. The keyboard layout, however, is as it should be: set to Dvorak. So, systemd-vconsole-setup.service is doing its job.
I have narrowed down the problem to that when agetty starts, it seems to be resetting the font back to the default. I have tried adding nouveau (my machines have Nvidia) to the array of modules within /etc/mkinitcpio.conf and rebuilding initramfs, but I get the same results. I have also tried adding vconsole.font=Lat2-Terminus16 to the boot arguments in GRUB, but I get the same results. This is affecting both of my machines. I have updated them with pacman -Syu, but the problem still exists.
I have found a workaround which is to add a service to systemd (I call it fontfix.service), set it to start after getty.target, and have it included in multi-user.target. But is there a better way? Or is something else other than agetty resetting the font?
tl;dr
agetty appears to be resetting the console font after systemd-vconsole-setup.service sets the font. Is there a way to have agetty recognize what console font is currently is use? Or is something else other than agetty resetting the font?
Last edited by linux2647 (2013-01-10 07:30:30)

https://wiki.archlinux.org/index.php/Sy … er_boot.3F

IPod 120 GB classic resets during playlists

Hello Everyone
I've had my ipod classic since 2008 so the warrenty with Apple is void but I do have an extended care plan with Walmart until Sept. 2011. My ipod has recently started resetting iself during playlists anytime I have it plugged into a docking station. I haven't experienced a problem with it yet when only using headphones. The other day during one of it's resets the top of the screen was blue and fuschia and the apple logo was "twitching". I did a soft reset and then everything was fine.
My questions are: Should I attempt to restore my ipod first or should I send it back for repairs? Has anyone else experienced a similar problem? Or does anyone know what could be wrong and how to fix it? I've taken wonderful care of my ipod- it still looks brand new and I've neven careless with it and am really concerned at this point. Please help!

Thanks for the reply .Appreciate your response.
I will go home and try whether i am able to connect. Currently i am using my office computer.
Before formatting i was able to play music in fact i was listneing to the songs by connecting the iPod to my car. When i connected the iPod to my office laptop it asked me to format it and i did.
Let me try it with another computer and i will respond.
Regards

Spontaneous reset during call with Iphone 3GS running iOS 5

My iPhone 3GS crashes almost everytime during a call. When I'm calling some-one or some-one is calling me the phone suddenly resets after 2 or 3 minutes. Is this a HW or Software problem. In my diagnostics list I see quite some panic messages with CRC errors.

"Spontaneous reset" - maybe you mean spontaneous restart - the phone can't reset itlself.
Could be either hardware or software. Restore the phone in iTune using a backup and if this continues restore as new, without using a backup. If restoring as new doesn't help, there is a hardware issue.

SSC-400 / SSC-600 / IPsec SPA resets during SSO

Similar Messages

Maybe you are looking for