SSD in Power Mac G5 modell 11.2 and 7.3

Hi,
I have two PM G5, one modell 11.2 (dual 2,3 GHz CPUl) and one 7,3 (dual 2,0 GHz CPU) that I wish to speed up by installing an SSD HD but there are many variations of SSD, does anyone have a SSD (240 GB) who can be recomended for use in the PM G5? Is it "plug an play" or does one need an 2,5" to 3,5" adapter to the HD bay?

Hello, you need an adapter, but also need one that is SATA 1.5 Gb/s compatable...
Here's one...
http://eshop.macsales.com/item/OWC/SSDEX3G240/
This OWC SSD Model is compatible with nearly any Mac or PC model with a Serial ATA connection (SATA, SATA 2.0, or SATA 3.0) including:
All Mac Pro models
All PowerMac G5 models
All MacBook Pro models
All Mac mini 2006-Current (All Intel Models)
iMac 2006-current (All Intel Models)
iMac G5
All MacBook models
Xserve 2009

Similar Messages

I have a Power Mac G5 with Cs4 Quark and I need to upgrade to CS5 - is this possible?

I have a Power Mac G5 with CS4 Quark and I need to upgrade to CS5. Is this Possible?? If so what do I need to do??

This forum is for troubleshooting Apple Software Update for Windows, a software package for Windows designed to update Apple products that run on Windows, and not related to your question in any way. And since CS is an Adobe product, you should probalby contact them.

I have a Power Mac G5 quad core (2006) and it does not work.

I have a Power Mac G5 Quad core (2006) and it does not work.The status light flashes twice and the fans blow full blast. The display does not show anything. Does anybody know what is wrong with my mac.

Can you count the beeps or flashes?
1 beep = no RAM installed
2 beeps = incompatible RAM types
3 beeps = no good banks
4 beeps = no good boot images in the boot ROM (and/or bad sys config block)
5 beeps = processor is not usable
In addition to the beeps, on some computers the power LED will flash a corresponding number of times plus one. The LED will repeat the sequence after approximately a 5-second pause. The tones are only played once.
Note: In this case, a flash is considered to be 1/4 second or 250 ms or greater in length.
http://support.apple.com/kb/HT1547
Might be time to replace the PRAM Battery, 4 years is close to their lifespan, far less if ever without AC power, & can cause strange startup problems...
See which one your G5 has, should be the 1st one ..
http://eshop.macsales.com/item/Newer%20Technology/CR2032/
http://eshop.macsales.com/item/Newer%20Technology/BAA36VPRAM/
If you're sure the RAM is good, try the Hair Dryer trick...
http://discussions.apple.com/message.jspa?messageID=13240047#13240047
https://discussions.apple.com/message/15223603#15223603
https://discussions.apple.com/message/15499912#15499912
https://discussions.apple.com/message/15613068#15613068
https://discussions.apple.com/thread/3270112
https://discussions.apple.com/message/16053892#16053892
No power light at all...
https://discussions.apple.com/thread/3692775?tstart=0
It can show on any G5, and even many other computers & electronic devices of the period.
http://www.macintouch.com/reliability/pmg5.html
http://lowendmac.com/ppc/power-macintosh-g5.html
And see this last one in particular...
https://discussions.apple.com/message/16781690#16781690
Heat gun better...
https://discussions.apple.com/thread/3916312?tstart=0

Power Mac G4 (sawtooth) AGP - Firmware and other issues

Hello,
So I was given an older Power Mac G4 AGP which I've been using while my Power Book G4 gets a logic board replacement but I've been having some issues with the AGP unit. How do you check to see what version of the firmware you have? I read a firmware update but it requires OS 9 to launch and I don't know if I need this or not. The other issue has been when I tried to run Firefox after successfully installing it. Firefox doesn't launch, it just opens and then closes. When I use Safari, the browser will work for about a few minutes but then it will freeze and I need to force quit it. I am running 10.4.11 and I was thinking of installing 10.5.6 but I'm not sure if this is possible with the Sawtooth. Do I need to upgrade the processor? Any advice or help is appreciated.

Hi, veesh678 -
Early models of the G4 (AGP) models came with OS 8.6; later models came with an installer for a model-specific version of OS 9.0.4. The latter disk will have a blue-gray label, be named "Power Mac G4" with a subtitle "Software Install", and has a part number of 691-2657-A (the part number will be in fine print on the right-hand side of the label).
Non-current firmware will not preclude the machine from booting to that CD; a retail OS 9.0.4 Install CD (white label, gold 9, no model named) probably will not work, although a retail OS 9.1 or 9.2.1 Install CD should work fine.
The current firmware version for the G4 (AGP) model is v. 4.2.8, which can be downloaded from this article -
Article #120068 - G4 Firmware Update 4.2.8
Note that to install that version the machine must be booted to OS 9.1 or OS 9.2.x from its hard drive, and the firmware update must be run from the same hard drive.
Before installing firmware update v. 4.2.8, download and run DIMM First Aid (it's a free download) to verify the compliance of the RAM in the machine.

Power Mac G4 Won't startup and ejects boot disk.

Hello,
Recently, I got a used Power Mac G4. On startup, it gets to the loading bar and doesn't load anything. It's just a blank white bar with no text aside from the apple logo at the top of the window. I tried inserting the Tiger recovery disk, but when I turn it on, it ejects the disk. I made sure that my keyboard and mouse were not plugged in as it was booting up (there are no other devices that may be causing it to eject), but it's still not solving the problem.
What could possibly be causing this problem?
Thanks,
Nami

It could easily be many things, Logic Board, RAM,Corrupted PRAM or NVRAM, even PSU or anything else, we just have don't have enough data out here to narrow it down yet.
I don't suppose it boots into Target mode...
http://support.apple.com/kb/HT1661
EDIT: Sometimes even a flaky Optical Drive will prevent normal operation & needs to be disconnected.
Might be time to replace the PRAM Battery, 4 years is close to their lifespan, far less if ever without AC power, & if weak can cause really strange problems...
http://eshop.macsales.com/item/Newer%20Technology/BAA36VPRAM/

What is the Best Power MAC G5 for Graphic Design and Video Edit

I need the Best Power MAC G5 Processor CPU
and Ram HDD Graphic card for Graphic Design and Video Edit
and the name of the Processor
how much the price

Hi GabreilKnight;
You are aware that the PowerMac G5 is no longer being produced hence if you find one it will be on the used market?
For what you are looking at doing I would suggest that you consider a Mac Pro instead.
Allan

HT1338 I have a Power Mac G5 running 10.4 and am trying to upgrade OS. Need Help.

I have a Power Mac G5 with an OS 10.4; what upgraces are available?

Leopard 10.5.8 is the last operating system a PowerPC Mac can be upgraded to.
Everything else newer requires Intel.
The DVD for Leopard are getting expensive since Aple has stopped producing them.
Allan

Power mac g5--won't boot, and I can't sleep

Hi all,
I'm hoping someone is awake and can help. My power mac g5, circa 2005, has always come with some problems, specifically, kernal panics. It's not bad RAM, but I have never tested the video card. Oddly enough, it seems to go down most often in the most in simple internet applications.
Today, it froze in Firefox and I cannot get it to reboot. It stalls/freezes in the gray apple screen. Called my IT friend, and he said to zap the PRAM. That brought it back up for a second, and then it froze again. I replaced the battery, no results.
I can't get it to boot in safe mode or even single-user- it freezes up as well. I certainly can't get it up long enough to load the boot disk.
It may be garbage...I can accept that...but it is holding hours of work. Will I be able to retrieve this??
Help
Message was edited by: nigelsupercat

Hi, I'm having same problem. G5 1.8 dual processor purchased March '05, won't boot. Not from cd either.
Took it to the apple geniuses and first was told it might be a bad board or processor and that I might as well just buy a new system. Well, I can't, because I still need to run some classic applications for business reasons, and because of that I'm stuck at Mac OS X 10.3.9. Anyway... I left my system with the apple geniuses and got a call 3 days later saying it was fixed @ no charge and that the 3rd party USB card was bad. They pulled it and said all was well.Great!, saving me $800 charge for a new board and over $430 for a new processor. So on the way home I buy a new USB hub get home start up and nothing! No change. Back to the Apple Store and after some testing this time I'm told it's definitely a bad hard drive. So, on the way home I buy a new hard drive. Get back, install the new HD and, you guessed it, can't format the disk, system won't boot from CD. BACK TO THE APPLE GENIUSES AGAIN! Now they tell me it's definitely the logic board. After 5 days I'm back where I started... except I have an old USB card that is most likely fine and new USB hub and a new HD I purchased because the Apple Geniuses told me they were bad! I asked them if they would apply a credit of some sort for the unnecessary purchases and my time (The closest Apple Store is 30 miles away), They politely said we appologize for the inconvenience, but no, we can't do that. I've been using Macs of all kinds since the early 1980's. And have never had one fail! Since I started looking into G5 problems, I've found many others with this startup issue. I feel there is a known issue with this series that apple is intentionally sweeping under the rug instead of issuing a recall or credit.

Power mac g4 Model 8570 won't power on

A few months ago I installed Leopard on my g4 tower and since then I've been having power problems. I realized I pulled the wrong power cord in when I set everything back up, so I figured that waws the problem, thinking it was an issue of not drawing enough power; however, the problem has persisted. It used to be that I'd have to press the power button a couple of times for it to really take, then it was taking longer and longer to make that happen. Now it just won't power on at all. We popped the battery out for a bit, unplugged everything, and then re-assembled it but that didn't work. I keep reading about a pmu button or something, but I don't see anything like that and none of the diagrams on here match my logic board. can any one suggest what I can try? does my model even have a pmu button? I'm not that seasoned at trouble-shooting the hardware so any suggestions would be welcome.

Thanks so much, this was incredibly helpful! Unfortunately it didn't fix the problem tho. Is there anything else you would suggest I try before replacing the battery? I want to try all options before having to buy a new battery, and also whatever I can do before having to take it in somewhere (not having a car makes that a difficult task). Thanks again!

Back of power mac g4 model number m8493

i am trying to find out if i need a 4 or 6 pin i link 1394 cable to put movies from my sony handycam onto my g4. i know the camera uses a 4 pin but i need to know if i should go buy a 4 to 6 or a 4 to 4 cable. thank you

Not sure about the cable, but for reference, you have a Quicksilver model Mac.
See http://docs.info.apple.com/article.html?artnum=42739
 Cheers, Tom

POWER MAC GOES CRAZY ON FONTS AND CRASHED THE ENTIRE HARD DRIVE

I was working on my mac, and my illustrator program crashed. When i relaunched my finder, the entire desktop
was changed with a garamon font and my dock was missing.
Each time I opened a app it crashed automaticly. I had no more drop down menus in my tool bar the whole computer was crazy.
So I decided to reinstal my Mac OS X instal discs.
The problem is, It's panter not Tiger. Anyways...I have Panter on my machine now which seems to work fine but I can't open Safari anymore. I bounces in my dock once and that's it it doesn't even open. Do you know why my computer went Crazy and how can I solve my safari problem.
P.S. I might find some other problems but I haven,t opened all my apps yet.

Christian, it sounds like an incompatible font. Also, please refrain from posting in all upper case letters since it is like yelling and considered rude on the internet. Thanks.

Power Mac G5 seems to overheat and freeze on occasion

Over the past week, i have noticed my G5 overheating (fans blazing) and the machine frozen. What can I do to correct this problem? It's the SP 1/6 GHz model. Thanks.

There may still be other issues, but if you haven't done it already a good cleaning is a good thing to do. Overheating can cause a symptom like yours.
Luck-
-DP

Power Mac G5 seems to overheat and freeze again

I had this problem about a month ago... the computer seems to lock up and freeze. Tried vaccuming the front and back ventilation and that seemed to help the last time, but today the problem seems to be re-occurring over and over. Any other suggestions.

There may still be other issues, but if you haven't done it already a good cleaning is a good thing to do. Overheating can cause a symptom like yours.
Luck-
-DP

Power Mac G5 apple logo stuck and fans running full speed

HI everybody,
I have been looking around in many forums and i noticed that a lot of people encountered a similar problem. Unfortunately untill now, nobody could give a real suggestion on how solve this issue.
In few words, my G5 (late 2005) 2gh 5gb ram 10.5.8 get stuck to the apple logo (grey initial screen) without going trough the start up. After a while the fans start to run full speed.
I have tried several solutions....but nothing so for.
I have reset the SMU button.
I removed all the ram slot and changed position.
The HD is ok and empty.
I even tried to warm the logic board with an hair drier as i read in a discussion...and i don't know why, the G5 could go trough the start up. Since it was active, i run the apple test. Result: All Ok
After rebooting successfully for 4/5 times, i switched it off. The morning after the G5 was dead again.
I am kind of lost.
Any suggestion?
Tnx

Try a Heat gun...
https://discussions.apple.com/message/16781690#16781690

I want to run hardware test on my Power Mac G5 but it isn't working.

What I tried:
I have the original install disc 1 which came with the machine in the optical drive (which is the usual one). I printed the hardware test guide which is on the disc, disconnected everything but mouse, keyboard and monitor. I tried to boot, pressing the Alt/Option key, but the "system picker" or boot menu won't show up. What happens is what somebody described as for "old world" macs: my system boots with no finder window open and without the white screen and apple logo (which usually shows up during startup).
I also tried something I found in a user manual pdf for Power Mac G5 on the apple archives: Booting and press-holding C (btw it's strange that this manual says something different than the manual on the original disc). What happens here is that my machine is booting from the original disc but it boots in Installation mode. I looked at every drop-down-menu I could find there for several times but there is definitely no hardware test, since this is thought to install Mac OS 10.4.
I also tried the Intel-way and holding D during boot, but no surprise, it only booted the first drive (like it should on a pre-Intel).
But something about this all is very strange. Yesterday night I tried all these steps above and when I was close to fall asleep in front of my monitor it suddenly worked and I made it finally into the hardware test. If I remember correctly, I was holding down the C key, but as I said a was pretty dizzy and can be mistaken. I ran hardware test once enhanced and it stopped during ram, giving me an error code I wrote down. But since I made it into the test and was so tired, I thought "lets continue tomorrow" which was my epic fail for this year, I guess. Today I repeated every step, every way I tried but it just doesn't work; and I read sooo many forums and Q&A's.
By the way here is my error code which appeared after 49 minutes (to proof I didn't dream this):
"2MEM/1/4: DIMM3/J14"
Why do I want to do this?
Around the 1st of September this year my Power Mac G5 didn't boot anymore (the fan speeding issue). After reading a little online I came to the point that its either my Ram memory or its my graphics card or its Pram or NVram. I resetted Pram and NVram, I also replaced battery and then it booted again for one day but on the following day it didn't. I repeated every step but the battery replacement since it was a brand new one. It can only be Ram memory or my Graphics card (which is the standard one for this machine).
Since then my Power Mac was rarely in use, only two or three times in Firewire Target Mode to access some of the data. Yesterday I wanted to do this again; booting it in FT mode but I must have connected my keyboard too late during booting and my machine surprisingly booted just fine! I was so stoked about this! Then I wanted to find out why it didn't work for a while and started several steps. Ran maintanance scripts, repaired the system volume, checked for enough free space, checked my Ram and then I stumbled on the interwebs over the hardware test which is delivered on the original install disc 1 and I never heard about this before (strange enough). What followed is written above.
What do I have?
I have this:
Modellname:
Power Mac G5
Modell-Identifizierung:
PowerMac7,3
Prozessortyp:
PowerPC G5 (3.0)
Prozessorgeschwindigkeit:
2 GHz
Anzahl der CPUs:
2
L2-Cache (pro CPU):
512 KB
Speicher:
4 GB
Busgeschwindigkeit:
1 GHz
Boot-ROM-Version:
5.2.4f1
Seriennummer (System):
CK52107BRTY
Hardware-UUID:
00000000-0000-1000-8000-000D93640EEE
Sorry for the German but I think you still get it. The PPC was delivered with 10.4 and I bought it used from a friend with his original Update disc to 10.5 and I updated to the max, 10.5.8. I have 2x 1TB drive (similar ones) together as a Raid0 and three partitions on it. (I know now that it doesnt make that much of a sense).
Yeah so I really want to find out why my machine didn't work for three months but since it is so old and I'm a student, it doesn't make any sense to me to go to an Apple store or similar to have it expensively serviced since there is no guarantee that these guys really help you (heard some stories about the local stores here).
Is there a way to re-access the hardware test and run it to the end?
As you might have noticed, I'm pretty desperate. I would soooooooo appreciate it!!
Best,
Erik

"2MEM/1/4: DIMM3/J14"
Replace the memory in the DIMM 3 slot.
If you are running Mac OS X 10.5 you can use this program to test your G5's memory:
http://www.kelleycomputing.net/Rember/
It will subject your RAM to a more thorough test than Apple Hardware Test.

SSD in Power Mac G5 modell 11.2 and 7.3

Similar Messages

Maybe you are looking for