SSD only stable when external?
Strange one this.
Bought a new OWC Mercury Extreme SSD.
First had these issues after installed internally, lots of spinning ball would not start up at all sometimes not the quickness you would expect from an SSD.
Anyway sent it back, they did all the updates checked everything and sent it back to me.
In the mean time i got an external enclosure with double usb power etc.
When i got the SSD i installed Mac OS on it externally got it upto where i needed all ok no problems at all.
Now once its back inside the Macbook Pro in the HD bay all the problems again.
Out to the external fine again.
So obviously not the SSD.
My normal HDD works fine inside the computer.
Any ideas?
Does anyone know how to check my firmware version?
Because apparently the firmware update from 1.6 to 1.7 didn't deal with SATA very well?
I've put the SSD inside a Late 06 White Macbook at it works fine.
Inside my MBP no good at all, only works in an external enclosure with that computer.
Similar Messages
-
So I tried to upgrade to Mavericks today and it failed (same error as in this post which seemed to be a common problem). It wouldn't let me repair the disk, and after trying all sorts I rebooted my computer in recovery mode - it wouldn't let me reinstall Lion because the hard drive was apparently locked and I could see no way around this. So I decided to restore from a Time Machine backup on an external hard drive and that worked okay, except my MacBook now only works when the external hard drive is connected. If I remove the external hard drive, I'm back to square one as it still won't let me reinstall Lion as the HD is locked!
I have no idea what's going on. HELP!The startup drive is failing, or there is some other internal hardware fault.
Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.
If privacy is a concern, erase the data partition(s) with the option to write zeros* (do this only if you have at least two complete, independent backups, and you know how to restore to an empty drive from any of them.) Don’t erase the recovery partition, if present.
Keeping your confidential data secure during hardware repair
Apple also recommends that you deauthorize a device in the iTunes Store before having it serviced.
*An SSD doesn't need to be zeroed. -
New SSD only boots when option key held down.
I recently cloned the original HDD in my mid-2009 MBP [2,53] to a brand new SSD. I put the SSD in an external enclosure, formatted and then cloned.
Then I put replaced the internal HDD with the SSD and put the HDD to rest in a drawer forever. If I hold down option upon startup, I'm able to choose the new SSD and launch. But if I just turn my MBP on, I simply get a white/grey screen.
Not a giant problem, but not sure why it would not just boot normally. Is there some kind of step required to make the new SSD the default startup drive?
Thank you.Shootist007 wrote:
Also if this one one of these new iMacs that come with the bluetooth wireless keyboards that is also the problem. These BT keyboard are not recognized right away when the system turns on so it is a Hit & Miss type of thing getting any of the Boot Options to work correctly. If you press to soon it is not registered. If you pres to late the system has already bypassed the system to use the boot option keys. this is not only for the Option key press to bring up the Boot selection screen. it also doesn't work for the Recovery HD boot or the boot from DVD key and any other boot option keys.
As far as I can tell the window in which you should press the key runs from the start (but not before) of the chime to before it ends (bit vague). -
Hey – I am having a very strange issue with my external monitor; where it only works if my external speakers are plugged in and connected.
I am using a late 2011 Macbook pro, running Mavericks 10.9.4, along with an MBox 2 (USB Audio Interface), and two powered speakers (KRK Rokit 5). This setup has had no issues. I have just acquired an external monitor (Benq T2200HD), which I am using with a thunderbolt to VGA adaptor (a cheap Chinese knockoff adaptor).
To start - I plugged the monitor in with the thunderbolt adaptor, and it powers up and works fine. However, there is a nasty buzz coming from the speakers. I did some research and it looks like a simple ground loop issue. I did a bit of troubleshooting, and this is where things get weird.
What I found is - If I unplug the MBox, the monitor loses signal from the computer (displaying ‘No Signal Detected!’). Further, if I keep the MBox plugged in, however unplug both the cables from the MBox to the speakers, the monitor loses signal. It doesn’t matter if the speakers are turned off, however they need to be plugged in (or the monitor loses signal). Weirder still, I can unplug the MBox, however the monitor will work if I plug in the speakers through my macs headphone jack.
Simply put, the monitor only works if there is a direct connection between the computer, the speakers, and the power source. What is going on here? Is the monitor grounding through the computer port, to the speakers (I don’t know how this works, is this possible?). Could it somehow be the cheap VGA adaptor I am using?
Some other information:
- Everything is plugged into the same multi-box for power. I have tried plugging things into separate sources, and the result is the same.
- If I unplug the thunderbolt adaptor, then the speaker noise disappears straight away.
- The ground noise doesn’t appear in my headphones, which are plugged into the MBox.
Any information would be great – am I missing something here, or is this genuinely weird?Well, I went back into Best Buy to test on 3 other laptops (2 Asus, and their floor model for this Sony). It seems to be doing the same problem so at least I was able to rule out broken hardware issue on my particular laptop.
Here's what I did to test:
Since I couldn't really install Adobe Premiere on their machines, I used the DVIO software (http://www.carr-engineering.com/dvio.htm) and a 5 min clip I captured. I transferred onto their machines, hooked up my Sony D8, and attempted to play the video. It would play for 15 seconds and then stop and jitter with a loud noise (like it does on my laptop). I even tried changing each machine's firewire driver to the legacy one and same results. I pulled a brand new 4 pin to 4 pin firewire cable off their shelf and still the same problem.
I think I've nailed it down to Win7x64 bit Home Edition not playing nice with Firewire driver. Very annoying. I can't find any concrete evidence of this from other users on any of the forums that have my particular problem, but from my own testing, it's all I can conclude.
I have 2 other things I can try:
1. Opening the laptop and looking at the firewire to maybe find appropriate driver (ugh, I don't want to have to open this thing up).
2. Upgrading to Win7x64bit Pro and possibly testing with XP on the new MS Virtual PC (http://www.microsoft.com/windows/virtual-pc/). I can't do it with my Home edition apparantly.
Who needs to view video on an external TV anyways....sheeesh...(scarcasm).
Tim -
Font embedding only works when external HD present
I have an old FLA project that I copied from an external HD.
When publishing this FLA, the mac finder gives this message "flash is trying to access files on your external HD. Allow?"
When I allow it, all goes well. When I don't allow it or when the external HD is not present, flash cannot embed fonts.
I do have the proper fonts on my system and in the library. I don't have these font problems with other FLA files.
If I copy all the internal frames and library elements into a new clean FLA, the problem still exists...
How can I get this flash file to embed the right font???check your publish settings and make sure there's not absolute path to the swf (or any of the other published files).
-
Strange issue with external monitor, only working when external speakers plugged in
Hey – I am having a very strange issue with my external monitor; where it only works if my external speakers are plugged in and connected.
I am using a late 2011 Macbook pro, running Mavericks 10.9.4, along with an MBox 2 (USB Audio Interface), and two powered speakers (KRK Rokit 5). This setup has had no issues. I have just acquired an external monitor (Benq T2200HD), which I am using with a thunderbolt to VGA adaptor (a cheap non-apple adaptor).
To start - I plugged the monitor in with the thunderbolt adaptor, and it powers up and works fine. However, there is a nasty buzz coming from the speakers. I did some research and it looks like a simple ground loop issue. I did a bit of troubleshooting, and this is where things get weird.
What I found is - If I unplug the MBox, the monitor loses signal from the computer (displaying ‘No Signal Detected!’). Further, if I keep the MBox plugged in, however unplug both the cables from the MBox to the speakers, the monitor loses signal. It doesn’t matter if the speakers are turned off, however they need to be plugged in (or the monitor loses signal). Weirder still, I can unplug the MBox, however the monitor will work if I plug in the speakers through my macs headphone jack.
Simply put, the monitor only works if there is a direct connection between the computer, the speakers, and the power source. What is going on here? Is the monitor grounding through the computer port, to the speakers (I don’t know how this works, is this possible?). Could it somehow be the cheap VGA adaptor I am using?
Some other information:
- Everything is plugged into the same multi-box for power. I have tried plugging things into separate sources, and the result is the same.
- If I unplug the thunderbolt adaptor, then the speaker noise disappears straight away.
- The ground noise doesn’t appear in my headphones, which are plugged into the MBox.
Any information would be great – am I missing something here, or is this genuinely weird?Hello cgoldberg11
Please go to the below link to test if you are having a speaker hardware failure.
Testing for Hardware Failures (Windows 7)
This will rule out hardware failure, let me know how that goes.
Thanks
If I have solved your issue, please feel free to provide kudos and make sure you mark this thread as solution provided!
Although I work for HP, my posts and replies are my own opinion and not those of HP. .....
Reguards,
Mo -
Pictures only appear when external drive connected
Ok...so I selected all my pics in iPhoto from user acct #2 and drug them to my external hard drive. Then I logged into user acct #1, slected all pics in the external drive and drug them into iPhoto where they all seemed to import. However, when my external drive isn't plugged into my MacBood the imported pics show up in the interface but if I hit the space bar to blow them up to full size all I get is a gray ?. So what have I done and how do I fix it?
Thanks!Try going through the 5 R's to see if it helps. It's possible that a reset may fix things for you. You may have to do a restore, which would delete your files from the iPod and set it back to factory settings. You will then need to re-sync the music/pics to your computer.
http://www.apple.com/support/ipod/five_rs/ -
I downloaded several cds to my external hard drive in .mp3 format. Later, I copied them to iTunes. The songs only play when the external hard drive is plugged in. I tried to load the songs from iTunes to my iPhone and the songs don't play. I thought iTunes allowed me to transfer music to my iPhone and play it. What am I doing wrong?
Hi skoorb1,
When adding music to iTunes, you can set it to either make a local copy of the file, or simply point to the original location of the file (for example, on an external hard drive). If it is set to do the latter, it will not be able to play or transfer those files when the external hard drive is not plugged in. You may find the following article helpful:
iTunes: About the Add to Library, Import, and Convert functions
http://support.apple.com/kb/ht1347
Regards,
- Brenden -
Is there anyway to have an 11 inch mac air connected to an external monitor with lid closed and still be able to see content. I have a wireless ketboard and mouse and have tried everything. Only works when plugged in.
You are referring to a feature called Clamshell Mode, please read Clamshell Mode setup for instructions.
BTW when posting when you use generalities such as "have tried everything" this tells us nothing. When posting please be specific and try to paint a complete picture. It just makes things easier for those trying to help you. -
My iMac (2007) keeps shutting off when in Full Screen mode (DVD, iTunes Visualizer, etc.) This only happens when I have an external monitor hooked up HDMI. Help?
Try using another connection such as VGA or DVI to see if the problem repeats itself.
-
Lenovo spkrs work only when external spkrs plugged in
Arch runs great on noobies Lenovo 3000 n100.
Streaming audio and system sounds work fine only when external spkrs are plugged into headphone socket.
Onboard spkrs can be heard along with external spkrs together. I have tried every combination of Gnome-volume-control sliders and mutes to hear onboard spkrs by themselves but no luck. It's not a big deal as the laptop is always on my desk but I'm just curious if it can be fixed as I am not experienced enough yet.
Thanks
RegardsSee this recent thread. It may be instructive.
http://discussions.apple.com/thread.jspa?messageID=10899641� -
Why do I get no sound through the i-pad speakerts when using Keynotes but when external speakers or headphones are plugged in sound is there. Also how do you get back to the program page when in play mode on i-pad?
Whoa, I found the answer by clicking on one of the questions in the "More Like This" box to the right. I do wonder how to find that box before posting my dumb question. The answer turned out to be checking the youtube volume control. I turned that up and it solved the problem for Comast as well.
-
Speakers only play when headphones are plugged in.
My internal speakers only play when the headphones are plugged in. (System preferences-Sound tells me I'm using Internal Speakers, audio port for sound input). When I remove the headphones, the red light in the jack goes on and the computer says I'm using Digital Out ("The selected device has no output controls.)
I have read many community responses, most saying that the switch inside the headphone jack hasn't engaged, that I should fiddle with it using a paperclip/bobbypin/toothpick or just plug-in and unplug headphones repeatedly. I have repeatedly both of these to no avail. When fiddling, I don't really know which bump inside there is the switch, I've played with them all.
No, it's not dirty, I've blowin air, vaccuumed, dusted. Same problem.
I do use my speakers often for work and pleasure, go between different external speakers and a projector.
It seems that the computer has things backwards- headphones unplugged is pluged and vice versa.
Any suggestions or clear guidance as to what I should be fiddling with when I stick a bobby pin in there? No need to refer me to old posts, I've read them.
Thanks in advance,
TheKipIf your phone is still under warranty, Apple will service your phone for free.
Did you check the headphone port for any kind of debris or lint?
Did you already try another set of headphones? Are you suing the headphones that came with the phone?
Is the headphone jack plugged in fully into the headphone port? -
My Ipod classic 160gb is dead,It only responds when I plug it in to cpu via usb cable then the screen blinks.When I try to reset it the Apple logo appears but the apple logo blinks on and off to as long as i hold the buttons down,when i realease the reset buttons it just blinks back and fourth to the blank gray screen,it worked fine yesterday night this morning its tanked.is this unit completely dead or can something be done at home?
Thank you for your help
IceI wrote this long time ago, have a read and see whether it can be soloved
If a sad iPod icon or an exclamation point and folder icon appears on your iPod’s screen, or with sounds of clicking or HD whirring, it is usually the sign of a hard drive problem and you have the power to do something about it now. Your silver bullet of resolving your iPod issue – is to restore your iPod to factory settings.
http://docs.info.apple.com/article.html?artnum=60983
If you're having trouble, try these steps at different levels one at a time until the issue is resolved. These steps will often whip your iPod back into shape.
Make sure you do all the following “TRYs”
A. Try to wait 30 minutes while iPod is charging.
B. Try another FireWire or USB through Dock Connector cable.
C. Try another FireWire or USB port on your computer .
D. Try to disconnect all devices from your computer's FireWire and USB ports.
E. Try to download and install the latest version of iPod software and iTunes
http://www.apple.com/itunes/download/
For old and other versions of iPod updater for window you can get here
http://www.ipodwizard.net/showthread.php?t=7369
F. Try these five steps (known as the five Rs) and it would conquer most iPod issues.
http://www.apple.com/support/ipod/five_rs/
G. Try to put the iPod into Disk Mode if it fails to appear on the desktop
http://docs.info.apple.com/article.html?artnum=93651
If none of these steps address the issue, you may need to go to Intermediate level listed below in logical order. Check from the top of the lists to see if that is what keeping iPod from appearing on your computer in order for doing the Restore.
Intermediate Level
A. Try to connect your iPod with another computer with the iPod updater pre-installed.
B. Still can’t see your iPod, put it in Disk Mode and connect with a computer, instead of doing a Restore on iPod Updater. Go and format the iPod instead.
For Mac computer
1. Open the disk utility, hope your iPod appears there (left hand side), highlight it
2. Go to Tab “Partition”, click either “Delete” or “Partition”, if fails, skip this step and go to 3
3. Go to Tab “Erase” , choose Volume Format as “MAC OS Extended (Journaled), and click Erase, again if fails, skip it and go to 4
4. Same as step 3, but open the “Security Options....” and choose “Zero Out Data” before click Erase. It will take 1 to 2 hours to complete.
5. Eject your iPod and do a Reset
6. Open the iTunes 7 and click “Restore”
For Window computer
Go to folder “My Computer”
Hope you can see your iPod there and right click on the iPod
Choose “Format”. Ensure the settings are at “Default” and that “Quick Format” is not checked
Now select “Format”
Eject your iPod and do a Reset
Open the iTunes 7 and click “Restore”
In case you do not manage to do a “Format” on a window computer, try to use some 3rd party disk utility software, e.g.“HP USB Disk Storage Format Tool”.
http://discussions.apple.com/thread.jspa?threadID=501330&tstart=0
C. Windows users having trouble with their iPods should locate a Mac user. In many cases when an iPod won't show up on a PC that it will show up on the Mac. Then it can be restored. When the PC user returns to his computer the iPod will be recognized by the PC, reformatted for the PC, and usable again. By the way, it works in reverse too. A Mac user often can get his iPod back by connecting it to a PC and restoring it.
Tips
a. It does not matter whether the format is completed or not, the key is to erase (or partly) the corrupted firmware files on the Hard Drive of the iPod. After that, when the iPod re-connected with a computer, it will be recognized as an fresh external hard drive, it will show up on the iTunes 7.
b. It is not a difficult issue for a Mac user to find a window base computer, for a PC user, if they can’t find any Mac user, they can go to a nearest Apple Shop for a favor.
c. You may need to switch around the PC and Mac, try to do several attempts between “Format” and “Restore”
http://discussions.apple.com/thread.jspa?messageID=2364921�
Advance Level
A. Diagnostic mode solution
If you have tried trouble shooting your iPod to no avail after all the steps above, chances are your iPod has a hardware problem. The iPod's built-in Diagnostic Mode is a quick and easy way to determine if you have a "bad" iPod.
You need to restart your iPod before putting it into Diagnostic Mode. Check that your hold switch is off by sliding the switch away from the headphone jack. Toggle it on and off to be safe.
Press and hold the following combination of buttons simultaneously for approximately 10 seconds to reset the iPod.
iPod 1G to 3G: "Menu" and "Play/Pause"
iPod 4G+ (includes Photo, Nano, Video, and Mini): "Menu" and "Select"
The Apple logo will appear and you should feel the hard drive spinning up. Press and hold the following sequence of buttons:
iPod 1G to 3G: "REW", "FFW" and "Select"
iPod 4G+ (includes Photo, Nano, Video, and Mini): "Back" and "Select"
You will hear an audible chirp sound (3G models and higher) and the Apple logo should appear backwards. You are now in Diagnostic Mode. Navigate the list of tests using "REW" and "FFW". The scroll wheel will not function while in diagnostic mode. For further details on Diagnostic mode can be found at http://www.methodshop.com/mp3/ipodsupport/diagnosticmode/
Try to do the 5in1, HDD R/W and HDD scan tests. Some successful cases have been reported after the running the few tests under the Diagnostic mode. In case it does not work in your case, and the scan tests reports show some errors then it proves your iPod has a hardware problem and it needs a repairing service.
B. Format your iPod with a start disk
I have not tried this solution myself, I heard that there were few successful cases that the users managed to get their iPod (you must put your iPod in disk mode before connecting with a computer) mounted by the computer, which was booted by a system startup disk. For Mac, you can use the Disk Utility (on the Tiger OS system disk), for PC user, you can use the window OS system disk. Try to find a way to reformat your iPod, again it does not matter which format (FAT32, NTFS or HFS+) you choose, the key is to erase the corrupted system files on the iPod. Then eject your iPod and do a Reset to switch out from Disk Mode. Reboot your computer at the normal way, connect your iPod back with it, open the iPod updater, and hopefully your iPod will appear there for the Restore.
If none of these steps address the issue, your iPod may need to be repaired.
Consider setting up a mail-in repair for your iPod http://depot.info.apple.com/ipod/
Or visit your local Apple Retail Store http://www.apple.com/retail/
In case your iPod is no longer covered by the warranty and you want to find a second repairing company, you can try iPodResQ or ifixit at your own risk
http://www.ipodresq.com/index.php
http://www.ifixit.com/
Just in case that you are at the following situation
Your iPod warranty is expired
You don’t want to pay any service charges
You are prepared to buy a new one
You can’t accept the re-sell value of your broken iPod
Rather than leave your iPod as paper-weight or throw it away.
You can try the following, but again, only do it as your last resort and at your own risk.
Warning !!!! – It may or may not manage to solve your problem, and with a risk that you may further damage your iPod, which end up as an expensive paper weight or you need to pay more higher repairing cost. Therefore, please re-consider again whether you want to try the next level
Last Resort Level
1. . Disconnecting the Hard Drive and battery inside the iPod – Warning !! Your iPod warranty will be waived once you open the iPod.
In Hong Kong there are some electronic shops offering an iPod service for Sad iPod, the first thing they do is to open up the iPod’s case and disconnecting the battery and the Hard Drive from the main board of the iPod. Wait for 5-10 minutes and reconnecting them back. The reason behind which I can think of is to do a fully reset of a processor of the iPod. In case you want do it itself and you believe that you are good on fixing the electronics devices and have experience to deal with small bits of electronic parts, then you can read the following of how to open the iPod case for battery and HDD replacement (with Quicktimes)
http://eshop.macsales.com/tech_center/index.cfm?page=Video/directory.html
2.Press the reset button on the Hard Drive inside the iPod – Suggestion from Kill8joy
http://discussions.apple.com/thread.jspa?messageID=2438774#2438774
Have I tried these myself? No, I am afraid to do it myself as I am squeamish about tinkering inside electronic devices, I have few experiences that either I broke the parts (which are normally tiny or fragile) or failed to put the parts back to the main case. Therefore, I agree with suggestion to have it fixed by a Pro.
2. Do a search on Google and some topics on this discussion forum about “Sad iPod”
Exclamation point and folder and nothing else
Spank your iPod
http://www.youtube.com/watch?v=3ljPhrFUaOY
http://discussions.apple.com/thread.jspa?messageID=3597173#3597173
Exclamation point and folder and nothing else
http://discussions.apple.com/thread.jspa?messageID=2831962#2831962
What should I do with my iPod? Send it or keep it?
http://discussions.apple.com/thread.jspa?threadID=469080&tstart=0
Strange error on iPod (probably death)
http://discussions.apple.com/thread.jspa?threadID=435160&start=0&tstart=0
Sad Face on iPod for no apparent reason
http://discussions.apple.com/thread.jspa?threadID=336342&start=0&tstart=0
Meeting the Sad iPod icon
http://askpang.typepad.com/relevant_history/2004/11/meeting_the_sad.html#comment -10519524
Sad faced iPod, but my computer won’t recognize it?
http://discussions.apple.com/thread.jspa?messageID=2236095#2236095
iPod Photo: unhappy icon + warranty question
http://discussions.apple.com/thread.jspa?messageID=2233746#2233746
4th Gen iPod Users - are we all having the same problem?
http://discussions.apple.com/message.jspa?messageID=2235623#2235623
Low Battery, and clicking sounds
http://discussions.apple.com/thread.jspa?messageID=2237714#2237714
Sad faced iPod, but my computer won’t recognize it
http://discussions.apple.com/thread.jspa?messageID=2242018#2242018
Sad iPod solution
http://discussions.apple.com/thread.jspa?threadID=412033&tstart=0
Re: try to restore ipod and it says "can't mount ipod"
http://discussions.apple.com/thread.jspa?threadID=443659&tstart=30
iPod making clicking noise and is frozen
http://discussions.apple.com/thread.jspa?messageID=2420150#2420150
Cant put it into disk mode
http://discussions.apple.com/thread.jspa?messageID=3786084#3786084
I think my iPod just died its final death
http://discussions.apple.com/thread.jspa?messageID=3813051
Apple logo & monochrome battery stay
http://discussions.apple.com/thread.jspa?messageID=3827167#3827167
My iPod ism’t resetting and isn’t being read by my computer
http://discussions.apple.com/thread.jspa?messageID=4489387#4489387
I am not suggesting that you should follow as well, but just read them as your reference. You are the person to make the call.
Finally, I read a fair comments from dwb, regarding of slapping the back of the iPod multiple times
Quote “This has been discussed numerous times as a 'fix'. It does work, at least for a while. In fact I remember using the same basic trick to revive Seagate and Quantam drives back in the mid to late 1980's. Why these tiny hard drives go bad I don't know - could be the actuator gets stuck in place or misaligned. Could be the platter gets stuck or the motor gets stuck. 'Stiction' was a problem for drives back in the 80's. Unfortunately the fix can cause damage to the platter so we temporarily fix one problem by creating another. But I know of two instances where a little slap onto the table revived the iPods and they are still worked a year or more later.”UnQuote -
Error when External Acquisition of asset F-90
Hi,
i had created entire asset accounting inclient 100 and transaported to client 400 inclueading group asset.
now when i am posting F-90 acquisition asset it is geving following error:
*Asset 6661 600002-0 is incomplete, check the asset
Message no. AAPO184
Diagnosis
The 'incomplete' indicator was set for asset 6661 600002-0 because required entries were not made.
System Response
In the standard system, the system rejects the posting to the asset and issues an error message. However, this error message can be changed in Customizing so that it is only a warning. However, if you make this change, you should be aware that it is then possible to post to the asset, although an additional account assignment is missing.
Procedure
Start report RAUNVA00 for the asset, and complete the asset's specifications. Then post the transaction again.*
can any one give me the solution
thanking you.Dear,
Mahesh.
DO not perform cross posting. Same quesiton is asked in SAP Financials and I answered there same as Nathan & Srinu sir.
Error when External Acquisition of asset F-90 in SAP Financials.
Requesting :- If you want to post in cross Forums please close previous one and then ask in new one.
As said in message run the RAUNVA00 report in SE38 or go to AUVA T.code.
Go to Company Code for which you are facing issue , then go to Levels of completion area select there 1 to 3.
Execute and see your asset no. Then see which fields are incomplete and fill them with proper value in AS02.
Save & Run F-90.
I hope this will help you to solve the issue. If you have any doubts feel free to share.
Regards,
Pankaj A Bhalerao.
Maybe you are looking for
-
How to get the data type of a variable
Hi I'm new to java and I'd like to put some variables with different data type into the HashMap. But when I'm going to get the value of the variable I want to know its data type (int,String,long,float etc.) before I do some processing. here's my samp
-
UIX: How to get tooltip help on tabs and global buttons?
Our users love tooltip help (the yellow pop-up help text that is displayed when you hold the mouse above an image or hyperlink). The shortDesc attribute sets the tooltip help on most elements. But it doesn't seem to work for (level 1) tabs (i.e. a li
-
27" iMac was stolen, now returned but has been locked what do I do?
My 27' iMac was stolen, now returned but has been locked what do I do? It was purchased in December of 2011, they nust have set up icloud account to lock it. How do I get around this? Apple should have my serial number of this computer matching my ac
-
Since downloading IOS 6.1 on my Iphone 4, my Apps states updates available but when I go into "updates" there's a blank screen. How do I fix this?
-
Failed to install osx on externa WD HD
I was wondering if anyone knows what could be happening here? My HD failed on me yesterday, So I am trying to install osX on a brand new external HD from WD (my book series). I have partitioned with the GUID Partition Table and the format is on Mac O