SSID Priorities
At the college I'm at, there's a huge wireless network which stretches across the entire campus. With my Time Capsule, I set up another network so I could control my Apple TV and iTunes via remote. When I leave my dorm, I'm required to connect back to the main campus network. However, when I return to my dorm, It does not auto-connect to my network.
My question is: Is there a way to make one SSID a higher preference than the other on the iPhone?
HI Jason,
Might be some help here.
http://www.tech-faq.com/ssid.shtml
Carolyn
Similar Messages
-
Hello all)
I have the task to configure QoS for SSID. I have 1602E points and 4 SSIDs per point. I want to priorities one of them. APs are connected to cisco 3850. Please help me how can I do it?Bandwidth and Priority Management at SSID Level
The next step is to take care of the QoS policy at the SSID level. This step applies to both the Catalyst 3850 switch and to the 5760 controller. This configuration assumes that voice and video traffic is identified through the use of class-map and access-lists and is tagged properly. However, some incoming traffic that is not targeted by the access-list may not display its QoS marking. In that case, you can decide if this traffic should be marked with a default value or left untagged. The same logic goes for traffic already marked but not targeted by the class-maps. Use the default copy statement in a table-map in order to ensure that unmarked traffic is left unmarked and that tagged traffic keeps the tag and it not remarked.
Refer the link for the Complete Configuration : www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/116479-configure-qos-00.html#anc15 -
Unable to get IP on one ssid of a two ssid autonomus 1141 AP
We recently added a second ssid at a remote site AP but the clients cannot get an IP. They get associated to the AP but no IP.
The ssid we added is using the default vlan 1 which is where the dhcp server is located.
The other ssid vlan 101 is the visistor network and it gets an ip from the ASA. It works just fine.
The AP is connected to a 3560 swtich like so:
interface GigabitEthernet0/48
description link to WAP
switchport trunk encapsulation dot1q
switchport mode trunk
load-interval 30
If we put a static reservation in the dhcp for the client mac address it works fine. But dynamic dhcp does not work.
Attached is the config of the AP.
Vlan 1 is the ssid that does not get a dynamic IP.Your config looks good, but like Rasika mentioned, I would remove infrastructure-ssid optional just to see if it works... now I would also configure a port on the same switch as the ap is connected to and set that to vlan 1 and make sure that laptop gets an ip address.
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered" -
How to find ssid number on ipad 3 to connect hp Photosmart 6510 B211a
How to find SSID number to enable ePrint from IPAD 3 to hp photosmart6510 B211a.
Hello enceugh,
If you are trying to print over your home network, follow the directions on step 4 under the heading, "What if a 'No Airprint Printers Found' message displays on my Apple device?" here.
-------------How do I give Kudos? | How do I mark a post as Solved? -------------------------------------------------------- -
I'm running iTunes Remote App from a couple of iPhone 5's and a first generation iPod Touch. iTunes is running on a PC - Windows 7. My home network runs two Wifi Routers, each with a different SSID. I've had no problems with the Remote app running this set up for the last 8 months but recently the App can only find my iTunes library when the iPhone/iPod is connected via one specific router, when connected to the network via the other router, no iTunes library is found. I'm also running an Apple TV and it's the same as the iTunes Library, only visible via the one SSID.
Everything else seems to work fine when connected via either router, eg Internet on the iPhones (definitely via wifi)
I've tried renewing the lease on the iPhone wifi connection, restarting everything.....several times.....
It used to work fine, this only seems to have been a problem in recent weeks
Any help or advice would be much appreciated
Thanks
IanIt turned out to be the firewall settings on our router. Her machine was sending traffic that our router interpreted as a DoS attack and blacklisted her Airport's MAC address. That's why it would work fine if she switched to Ethernet.
-
Problem with roamingin in VoIP SSID...
Hi guys,
My client has a WLC 5508 with a two dosens of 1262s. I set SSID for the VoIP but when the client roams there is a loss of packest. The client is using Cisco phones. Any help will be appreciated.
Pete
(Cisco Controller) >show wlan 144
WLAN Identifier.................................. 144
Profile Name..................................... VoIP_Network
Network Name (SSID).............................. Inside_144
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Disabled
Network Admission Control
Radius-NAC State............................... Disabled
SNMP-NAC State................................. Disabled
Quarantine VLAN................................ 0
Maximum number of Associated Clients............. 0
Maximum number of Clients per AP Radio........... 200
Number of Active Clients......................... 10
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 1800 seconds
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ 144_v
Multicast Interface.............................. Not Configured
WLAN IPv4 ACL.................................... unconfigured
WLAN IPv6 ACL.................................... unconfigured
DHCP Server...................................... Default
DHCP Address Assignment Required................. Disabled
Static IP client tunneling....................... Disabled
Quality of Service............................... Platinum
Scan Defer Priority.............................. 4,5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Allowed
WMM UAPSD Compliant Client Support............... Disabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
Passive Client Feature........................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... 802.11b and 802.11g only
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
Radius Servers
Authentication................................ Global Servers
Accounting.................................... Global Servers
Interim Update............................. Disabled
Dynamic Interface............................. Disabled
Local EAP Authentication......................... Disabled
Security
802.11 Authentication:........................ Open System
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Enabled
WPA (SSN IE)............................... Enabled
TKIP Cipher............................. Enabled
AES Cipher.............................. Disabled
WPA2 (RSN IE).............................. Disabled
Auth Key Management
802.1x.................................. Disabled
PSK..................................... Enabled
CCKM.................................... Disabled
FT(802.11r)............................. Disabled
FT-PSK(802.11r)......................... Disabled
FT Reassociation Timeout................... 20
FT Over-The-Air mode....................... Enabled
FT Over-The-Ds mode........................ Enabled
GTK Randomization.......................... Enabled
SKC Cache Support.......................... Disabled
CCKM TSF Tolerance......................... 1000
Wi-Fi Direct policy configured................ Disabled
EAP-Passthrough............................... Disabled
CKIP ......................................... Disabled
Web Based Authentication...................... Disabled
Web-Passthrough............................... Disabled
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Disabled
FlexConnect Local Switching................... Disabled
FlexConnect Local Authentication.............. Disabled
FlexConnect Learn IP Address.................. Enabled
Client MFP.................................... Optional but inactive (WPA2 not configured)
Tkip MIC Countermeasure Hold-down Timer....... 60
Call Snooping.................................... Disabled
Roamed Call Re-Anchor Policy..................... Disabled
SIP CAC Fail Send-486-Busy Policy................ Enabled
SIP CAC Fail Send Dis-Association Policy......... Disabled
KTS based CAC Policy............................. Disabled
Band Select...................................... Disabled
Load Balancing................................... Disabled
Multicast Buffer................................. Disabled
Mobility Anchor List
WLAN ID IP Address Status
802.11u........................................ Disabled
Access Network type............................ Not configured
Network Authentication type.................... Not configured
Internet service............................... Disabled
HESSID......................................... 00:00:00:00:00:00
Hotspot 2.0.................................... Disabled
WAN Metrics configuration
Link status.................................. 0
Link symmetry................................ 0
Downlink speed............................... 0
Uplink speed................................. 0
Mobility Services Advertisement Protocol....... Disabled
(Cisco Controller) >
(Cisco Controller) >
(Cisco Controller) >debug client 2c:54:2d:ea:d4:0e
*apfMsConnTask_2: Nov 30 17:02:25.463: 2c:54:2d:ea:d4:0e Association received from mobile on AP 34:bd:c8:b2:b1:10
*apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1697)
*apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1864)
*apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e Applying site-specific Local Bridging override for station 2c:54:2d:ea:d4:0e - vapId 144, site 'Floor_1', interface '144_v'
*apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e Applying Local Bridging Interface Policy for station 2c:54:2d:ea:d4:0e - vlan 144, interface id 12, interface '144_v'
*apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e Applying site-specific override for station 2c:54:2d:ea:d4:0e - vapId 144, site 'Floor_1', interface '144_v'
*apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1697)
*apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1864)
*apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e STA - rates (4): 130 132 139 150 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e STA - rates (12): 130 132 139 150 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e extSuppRates statusCode is 0 and gotExtSuppRatesElement is 1
*apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e Processing WPA IE type 221, length 22 for mobile 2c:54:2d:ea:d4:0e
*apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e apfMsRunStateDec
*apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e apfMs1xStateDec
*apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Change state to START (0) last state RUN (20)
*apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e pemApfAddMobileStation2: APF_MS_PEM_WAIT_L2_AUTH_COMPLETE = 0.
*apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e 10.123.201.4 START (0) Initializing policy
*apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e 10.123.201.4 START (0) Change state to AUTHCHECK (2) last state RUN (20)
*apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e 10.123.201.4 AUTHCHECK (2) Change state to 8021X_REQD (3) last state RUN (20)
*pemReceiveTask: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e 10.123.201.4 Removed NPU entry.
*apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e 10.123.201.4 8021X_REQD (3) DHCP required on AP 34:bd:c8:b2:b1:10 vapId 144 apVapId 2for this client
*apfMsConnTask_2: Nov 30 17:02:25.465: 2c:54:2d:ea:d4:0e 10.123.201.4 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 34:bd:c8:b2:b1:10 vapId 144 apVapId 2
*apfMsConnTask_2: Nov 30 17:02:25.465: 2c:54:2d:ea:d4:0e apfPemAddUser2 (apf_policy.c:268) Changing state for mobile 2c:54:2d:ea:d4:0e on AP 34:bd:c8:b2:b1:10 from Associated to Associated
*apfMsConnTask_2: Nov 30 17:02:25.465: 2c:54:2d:ea:d4:0e Scheduling deletion of Mobile Station: (callerId: 49) in 1800 seconds
*apfMsConnTask_2: Nov 30 17:02:25.465: 2c:54:2d:ea:d4:0e Sending Assoc Response to station on BSSID 34:bd:c8:b2:b1:10 (status 0) ApVapId 2 Slot 0
*apfMsConnTask_2: Nov 30 17:02:25.465: 2c:54:2d:ea:d4:0e apfProcessAssocReq (apf_80211.c:6290) Changing state for mobile 2c:54:2d:ea:d4:0e on AP 34:bd:c8:b2:b1:10 from Associated to Associated
*dot1xMsgTask: Nov 30 17:02:25.466: 2c:54:2d:ea:d4:0e Creating a PKC PMKID Cache entry for station 2c:54:2d:ea:d4:0e (RSN 0)
*dot1xMsgTask: Nov 30 17:02:25.466: 2c:54:2d:ea:d4:0e Setting active key cache index 0 ---> 8
*dot1xMsgTask: Nov 30 17:02:25.466: 2c:54:2d:ea:d4:0e Setting active key cache index 8 ---> 0
*dot1xMsgTask: Nov 30 17:02:25.466: 2c:54:2d:ea:d4:0e Initiating WPA PSK to mobile 2c:54:2d:ea:d4:0e
*dot1xMsgTask: Nov 30 17:02:25.466: 2c:54:2d:ea:d4:0e dot1x - moving mobile 2c:54:2d:ea:d4:0e into Force Auth state
*dot1xMsgTask: Nov 30 17:02:25.466: 2c:54:2d:ea:d4:0e Skipping EAP-Success to mobile 2c:54:2d:ea:d4:0e
*dot1xMsgTask: Nov 30 17:02:25.466: 2c:54:2d:ea:d4:0e Starting key exchange to mobile 2c:54:2d:ea:d4:0e, data packets will be dropped
*dot1xMsgTask: Nov 30 17:02:25.466: 2c:54:2d:ea:d4:0e Sending EAPOL-Key Message to mobile 2c:54:2d:ea:d4:0e
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_6: Nov 30 17:02:25.990: 2c:54:2d:ea:d4:0e Received EAPOL-Key from mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Nov 30 17:02:25.990: 2c:54:2d:ea:d4:0e Received EAPOL-key in PTK_START state (message 2) from mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Nov 30 17:02:25.990: 2c:54:2d:ea:d4:0e Stopping retransmission timer for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Nov 30 17:02:25.990: 2c:54:2d:ea:d4:0e Sending EAPOL-Key Message to mobile 2c:54:2d:ea:d4:0e
state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
*Dot1x_NW_MsgTask_6: Nov 30 17:02:26.015: 2c:54:2d:ea:d4:0e Received EAPOL-Key from mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Nov 30 17:02:26.015: 2c:54:2d:ea:d4:0e Received EAPOL-key in PTKINITNEGOTIATING state (message 4) from mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Nov 30 17:02:26.016: 2c:54:2d:ea:d4:0e apfMs1xStateInc
*Dot1x_NW_MsgTask_6: Nov 30 17:02:26.016: 2c:54:2d:ea:d4:0e 10.123.201.4 8021X_REQD (3) Change state to L2AUTHCOMPLETE (4) last state RUN (20)
*Dot1x_NW_MsgTask_6: Nov 30 17:02:26.016: 2c:54:2d:ea:d4:0e 10.123.201.4 L2AUTHCOMPLETE (4) DHCP required on AP 34:bd:c8:b2:b1:10 vapId 144 apVapId 2for this client
*Dot1x_NW_MsgTask_6: Nov 30 17:02:26.016: 2c:54:2d:ea:d4:0e 10.123.201.4 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 34:bd:c8:b2:b1:10 vapId 144 apVapId 2
*Dot1x_NW_MsgTask_6: Nov 30 17:02:26.016: 2c:54:2d:ea:d4:0e apfMsRunStateInc
*Dot1x_NW_MsgTask_6: Nov 30 17:02:26.016: 2c:54:2d:ea:d4:0e 10.123.201.4 L2AUTHCOMPLETE (4) Change state to RUN (20) last state RUN (20)
*Dot1x_NW_MsgTask_6: Nov 30 17:02:26.017: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Reached PLUMBFASTPATH: from line 5362
*Dot1x: Nov 30 17:02:26.017: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Adding Fast Path rule
type = Airespace AP Client
on AP 34:bd:c8:b2:b1:10, slot 0, interface = 1, QOS = 2
IPv4 ACL ID = 255, IPv6 ACL ID = 2
*Dot1x_NW_MsgTask_6: Nov 30 17:02:26.017: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 7006 Local Bridging Vlan = 144, Local Bridging intf id = 12
*Dot1x_NW_MsgTask_6: Nov 30 17:02:26.017: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255)
*Dot1x_NW_MsgTask_6: Nov 30 17:02:26.017: 2c:54:2d:ea:d4:0e Stopping retransmission timer for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Nov 30 17:02:26.017: 2c:54:2d:ea:d4:0e Key exchange done, data packets from mobile 2c:54:2d:ea:d4:0e should be forwarded shortly
*Dot1x_NW_MsgTask_6: Nov 30 17:02:26.017: 2c:54:2d:ea:d4:0e Sending EAPOL-Key Message to mobile 2c:54:2d:ea:d4:0e
state PTKINITDONE (message 5 - group), replay counter 00.00.00.00.00.00.00.02
*spamApTask5: Nov 30 17:02:26.017: 2c:54:2d:ea:d4:0e Sent EAPOL-Key M5 for mobile 2c:54:2d:ea:d4:0e
*pemReceiveTask: Nov 30 17:02:26.017: 2c:54:2d:ea:d4:0e 10.123.201.4 Added NPU entry of type 1, dtlFlags 0x0
*Dot1x_NW_MsgTask_6: Nov 30 17:02:26.036: 2c:54:2d:ea:d4:0e Received EAPOL-Key from mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Nov 30 17:02:26.036: 2c:54:2d:ea:d4:0e Received EAPOL-key in REKEYNEGOTIATING state (message 6) from mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Nov 30 17:02:26.036: 2c:54:2d:ea:d4:0e Stopping retransmission timer for mobile 2c:54:2d:ea:d4:0e
*apfMsConnTask_2: Nov 30 17:03:17.385: 2c:54:2d:ea:d4:0e Association received from mobile on AP 34:bd:c8:b2:b1:10
*apfMsConnTask_2: Nov 30 17:03:17.385: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1697)
*apfMsConnTask_2: Nov 30 17:03:17.385: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1864)
*apfMsConnTask_2: Nov 30 17:03:17.385: 2c:54:2d:ea:d4:0e Applying site-specific Local Bridging override for station 2c:54:2d:ea:d4:0e - vapId 144, site 'Floor_1', interface '144_v'
*apfMsConnTask_2: Nov 30 17:03:17.385: 2c:54:2d:ea:d4:0e Applying Local Bridging Interface Policy for station 2c:54:2d:ea:d4:0e - vlan 144, interface id 12, interface '144_v'
*apfMsConnTask_2: Nov 30 17:03:17.385: 2c:54:2d:ea:d4:0e Applying site-specific override for station 2c:54:2d:ea:d4:0e - vapId 144, site 'Floor_1', interface '144_v'
*apfMsConnTask_2: Nov 30 17:03:17.385: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1697)
*apfMsConnTask_2: Nov 30 17:03:17.385: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1864)
*apfMsConnTask_2: Nov 30 17:03:17.385: 2c:54:2d:ea:d4:0e processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_2: Nov 30 17:03:17.385: 2c:54:2d:ea:d4:0e processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_2: Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e STA - rates (4): 130 132 139 150 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_2: Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_2: Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e STA - rates (12): 130 132 139 150 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_2: Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e extSuppRates statusCode is 0 and gotExtSuppRatesElement is 1
*apfMsConnTask_2: Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e Processing WPA IE type 221, length 22 for mobile 2c:54:2d:ea:d4:0e
*apfMsConnTask_2: Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e apfMsRunStateDec
*apfMsConnTask_2: Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e apfMs1xStateDec
*apfMsConnTask_2: Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Change state to START (0) last state RUN (20)
*apfMsConnTask_2: Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e pemApfAddMobileStation2: APF_MS_PEM_WAIT_L2_AUTH_COMPLETE = 0.
*apfMsConnTask_2: Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e 10.123.201.4 START (0) Initializing policy
*apfMsConnTask_2: Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e 10.123.201.4 START (0) Change state to AUTHCHECK (2) last state RUN (20)
*apfMsConnTask_2: Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e 10.123.201.4 AUTHCHECK (2) Change state to 8021X_REQD (3) last state RUN (20)
*pemReceiveTask: Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e 10.123.201.4 Removed NPU entry.
*apfMsConnTask_2: Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e 10.123.201.4 8021X_REQD (3) DHCP required on AP 34:bd:c8:b2:b1:10 vapId 144 apVapId 2for this client
*apfMsConnTask_2: Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e 10.123.201.4 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 34:bd:c8:b2:b1:10 vapId 144 apVapId 2
*apfMsConnTask_2: Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e apfPemAddUser2 (apf_policy.c:268) Changing state for mobile 2c:54:2d:ea:d4:0e on AP 34:bd:c8:b2:b1:10 from Associated to Associated
*apfMsConnTask_2: Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e Scheduling deletion of Mobile Station: (callerId: 49) in 1800 seconds
*apfMsConnTask_2: Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e Sending Assoc Response to station on BSSID 34:bd:c8:b2:b1:10 (status 0) ApVapId 2 Slot 0
*apfMsConnTask_2: Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e apfProcessAssocReq (apf_80211.c:6290) Changing state for mobile 2c:54:2d:ea:d4:0e on AP 34:bd:c8:b2:b1:10 from Associated to Associated
*dot1xMsgTask: Nov 30 17:03:17.389: 2c:54:2d:ea:d4:0e Creating a PKC PMKID Cache entry for station 2c:54:2d:ea:d4:0e (RSN 0)
*dot1xMsgTask: Nov 30 17:03:17.389: 2c:54:2d:ea:d4:0e Setting active key cache index 0 ---> 8
*dot1xMsgTask: Nov 30 17:03:17.389: 2c:54:2d:ea:d4:0e Setting active key cache index 8 ---> 0
*dot1xMsgTask: Nov 30 17:03:17.389: 2c:54:2d:ea:d4:0e Initiating WPA PSK to mobile 2c:54:2d:ea:d4:0e
*dot1xMsgTask: Nov 30 17:03:17.389: 2c:54:2d:ea:d4:0e dot1x - moving mobile 2c:54:2d:ea:d4:0e into Force Auth state
*dot1xMsgTask: Nov 30 17:03:17.389: 2c:54:2d:ea:d4:0e Skipping EAP-Success to mobile 2c:54:2d:ea:d4:0e
*dot1xMsgTask: Nov 30 17:03:17.389: 2c:54:2d:ea:d4:0e Starting key exchange to mobile 2c:54:2d:ea:d4:0e, data packets will be dropped
*dot1xMsgTask: Nov 30 17:03:17.389: 2c:54:2d:ea:d4:0e Sending EAPOL-Key Message to mobile 2c:54:2d:ea:d4:0e
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_6: Nov 30 17:03:17.422: 2c:54:2d:ea:d4:0e Received EAPOL-Key from mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Nov 30 17:03:17.422: 2c:54:2d:ea:d4:0e Received EAPOL-key in PTK_START state (message 2) from mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Nov 30 17:03:17.422: 2c:54:2d:ea:d4:0e Stopping retransmission timer for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Nov 30 17:03:17.423: 2c:54:2d:ea:d4:0e Sending EAPOL-Key Message to mobile 2c:54:2d:ea:d4:0e
state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
*Dot1x_NW_MsgTask_6: Nov 30 17:03:17.433: 2c:54:2d:ea:d4:0e Received EAPOL-Key from mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Nov 30 17:03:17.433: 2c:54:2d:ea:d4:0e Received EAPOL-key in PTKINITNEGOTIATING state (message 4) from mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Nov 30 17:03:17.433: 2c:54:2d:ea:d4:0e apfMs1xStateInc
*Dot1x_NW_MsgTask_6: Nov 30 17:03:17.433: 2c:54:2d:ea:d4:0e 10.123.201.4 8021X_REQD (3) Change state to L2AUTHCOMPLETE (4) last state RUN (20)
*Dot1x_NW_MsgTask_6: Nov 30 17:03:17.433: 2c:54:2d:ea:d4:0e 10.123.201.4 L2AUTHCOMPLETE (4) DHCP required on AP 34:bd:c8:b2:b1:10 vapId 144 apVapId 2for this client
*Dot1x_NW_MsgTask_6: Nov 30 17:03:17.433: 2c:54:2d:ea:d4:0e 10.123.201.4 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 34:bd:c8:b2:b1:10 vapId 144 apVapId 2
*Dot1x_NW_MsgTask_6: Nov 30 17:03:17.433: 2c:54:2d:ea:d4:0e apfMsRunStateInc
*Dot1x_NW_MsgTask_6: Nov 30 17:03:17.433: 2c:54:2d:ea:d4:0e 10.123.201.4 L2AUTHCOMPLETE (4) Change state to RUN (20) last state RUN (20)
*Dot1x_NW_MsgTask_6: Nov 30 17:03:17.435: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Reached PLUMBFASTPATH: from line 5362
*Dot1x: Nov 30 17:03:17.435: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Adding Fast Path rule
type = Airespace AP Client
on AP 34:bd:c8:b2:b1:10, slot 0, interface = 1, QOS = 2
IPv4 ACL ID = 255, IPv6 ACL ID = 2
*Dot1x_NW_MsgTask_6: Nov 30 17:03:17.435: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 7006 Local Bridging Vlan = 144, Local Bridging intf id = 12
*Dot1x_NW_MsgTask_6: Nov 30 17:03:17.435: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255)
*Dot1x_NW_MsgTask_6: Nov 30 17:03:17.435: 2c:54:2d:ea:d4:0e Stopping retransmission timer for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Nov 30 17:03:17.435: 2c:54:2d:ea:d4:0e Key exchange done, data packets from mobile 2c:54:2d:ea:d4:0e should be forwarded shortly
*Dot1x_NW_MsgTask_6: Nov 30 17:03:17.435: 2c:54:2d:ea:d4:0e Sending EAPOL-Key Message to mobile 2c:54:2d:ea:d4:0e
state PTKINITDONE (message 5 - group), replay counter 00.00.00.00.00.00.00.02
*spamApTask5: Nov 30 17:03:17.435: 2c:54:2d:ea:d4:0e Sent EAPOL-Key M5 for mobile 2c:54:2d:ea:d4:0e
*pemReceiveTask: Nov 30 17:03:17.435: 2c:54:2d:ea:d4:0e 10.123.201.4 Added NPU entry of type 1, dtlFlags 0x0
*Dot1x_NW_MsgTask_6: Nov 30 17:03:17.447: 2c:54:2d:ea:d4:0e Received EAPOL-Key from mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Nov 30 17:03:17.447: 2c:54:2d:ea:d4:0e Received EAPOL-key in REKEYNEGOTIATING state (message 6) from mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Nov 30 17:03:17.447: 2c:54:2d:ea:d4:0e Stopping retransmission timer for mobile 2c:54:2d:ea:d4:0e
*emWeb: Nov 30 17:03:46.162: Configuring IPv6 ACL for WLAN:144, aclName passed is NULL
*apfReceiveTask: Nov 30 17:03:46.173: 2c:54:2d:ea:d4:0e apfSendDisAssocMsgDebug (apf_80211.c:2162) Changing state for mobile 2c:54:2d:ea:d4:0e on AP 34:bd:c8:b2:b1:10 from Associated to Disassociated
*apfReceiveTask: Nov 30 17:03:46.178: 2c:54:2d:ea:d4:0e Sent Disassociate to mobile on AP 34:bd:c8:b2:b1:10-0 (reason 1, caller apf_ms.c:5558)
*apfReceiveTask: Nov 30 17:03:46.183: 2c:54:2d:ea:d4:0e Sent Deauthenticate to mobile on BSSID 34:bd:c8:b2:b1:10 slot 0(caller apf_ms.c:5678)
*apfReceiveTask: Nov 30 17:03:46.183: 2c:54:2d:ea:d4:0e apfMsAssoStateDec
*apfReceiveTask: Nov 30 17:03:46.183: 2c:54:2d:ea:d4:0e apfMsExpireMobileStation (apf_ms.c:5716) Changing state for mobile 2c:54:2d:ea:d4:0e on AP 34:bd:c8:b2:b1:10 from Disassociated to Idle
*apfReceiveTask: Nov 30 17:03:46.183: 2c:54:2d:ea:d4:0e pemApfDeleteMobileStation2: APF_MS_PEM_WAIT_L2_AUTH_COMPLETE = 0.
*apfReceiveTask: Nov 30 17:03:46.183: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Deleted mobile LWAPP rule on AP [34:bd:c8:b2:b1:10]
*pemReceiveTask: Nov 30 17:03:46.183: 2c:54:2d:ea:d4:0e 10.123.201.4 Removed NPU entry.
*apfReceiveTask: Nov 30 17:03:46.183: 2c:54:2d:ea:d4:0e apfMsRunStateDec
*apfReceiveTask: Nov 30 17:03:46.183: 2c:54:2d:ea:d4:0e apfMs1xStateDec
*apfReceiveTask: Nov 30 17:03:46.183: 2c:54:2d:ea:d4:0e Deleting mobile on AP 34:bd:c8:b2:b1:10(0)Hi guys and Saravanan thank for the ideas....
the qualituy is getting better, not satisfactory for the customer though...
I have upgraded the firware as advised to 1.4.3 - I forgot to mention I have 7925g wifi phonee
I set the 802.1x + cckm with eap-fast and WPA2 and definately the quality of the calls got a huge improvement but still not enough. What can be the reason for the confinuing problems during roaming?
Guys, is it possible to set the CCKM without ACS (or WDS - i think that was the second option)
here is some output:
(Cisco Controller) show>wlan 3
WLAN Identifier.................................. 3
Profile Name..................................... test_wifi_144
Network Name (SSID).............................. test144
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Disabled
Network Admission Control
Radius-NAC State............................... Disabled
SNMP-NAC State................................. Disabled
Quarantine VLAN................................ 0
Maximum number of Associated Clients............. 0
Maximum number of Clients per AP Radio........... 200
Number of Active Clients......................... 1
Exclusionlist.................................... Disabled
Session Timeout.................................. 65535 seconds
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ 144_v
--More-- or (q)uit
Multicast Interface.............................. Not Configured
WLAN IPv4 ACL.................................... unconfigured
WLAN IPv6 ACL.................................... unconfigured
DHCP Server...................................... Default
DHCP Address Assignment Required................. Disabled
Static IP client tunneling....................... Disabled
Quality of Service............................... Platinum
Scan Defer Priority.............................. 4,5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Required
WMM UAPSD Compliant Client Support............... Disabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... ap-cac-limit
Wired Protocol................................... None
Passive Client Feature........................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... 802.11b and 802.11g only
DTIM period for 802.11a radio.................... 2
DTIM period for 802.11b radio.................... 2
Radius Servers
--More-- or (q)uit
Authentication................................ 172.16.106.53 1645
Accounting.................................... Disabled
Dynamic Interface............................. Disabled
Local EAP Authentication......................... Disabled
Security
802.11 Authentication:........................ Open System
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Enabled
WPA (SSN IE)............................... Disabled
WPA2 (RSN IE).............................. Enabled
TKIP Cipher............................. Disabled
AES Cipher.............................. Enabled
Auth Key Management
802.1x.................................. Enabled
PSK..................................... Disabled
CCKM.................................... Enabled
FT(802.11r)............................. Disabled
FT-PSK(802.11r)......................... Disabled
FT Reassociation Timeout................... 20
FT Over-The-Air mode....................... Enabled
FT Over-The-Ds mode........................ Enabled
--More-- or (q)uit
GTK Randomization.......................... Disabled
SKC Cache Support.......................... Disabled
CCKM TSF Tolerance......................... 1000
Wi-Fi Direct policy configured................ Disabled
EAP-Passthrough............................... Disabled
CKIP ......................................... Disabled
Web Based Authentication...................... Disabled
Web-Passthrough............................... Disabled
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Disabled
FlexConnect Local Switching................... Disabled
FlexConnect Local Authentication.............. Disabled
FlexConnect Learn IP Address.................. Enabled
Client MFP.................................... Optional
Tkip MIC Countermeasure Hold-down Timer....... 60
Call Snooping.................................... Disabled
Roamed Call Re-Anchor Policy..................... Disabled
SIP CAC Fail Send-486-Busy Policy................ Enabled
SIP CAC Fail Send Dis-Association Policy......... Disabled
KTS based CAC Policy............................. Disabled
Band Select...................................... Disabled
Load Balancing................................... Disabled
--More-- or (q)uit
Multicast Buffer................................. Disabled
Mobility Anchor List
WLAN ID IP Address Status
802.11u........................................ Disabled
Access Network type............................ Not configured
Network Authentication type.................... Not configured
Internet service............................... Disabled
HESSID......................................... 00:00:00:00:00:00
Hotspot 2.0.................................... Disabled
WAN Metrics configuration
Link status.................................. 0
Link symmetry................................ 0
Downlink speed............................... 0
Uplink speed................................. 0
Mobility Services Advertisement Protocol....... Disabled
(Cisco Controller) >debug client 2C542DEAD40E
*apfMsConnTask_3: Dec 07 13:55:49.522: 2c:54:2d:ea:d4:0e Adding mobile on LWAPP AP 34:bd:c8:b3:d9:f0(0)
*apfMsConnTask_3: Dec 07 13:55:49.522: 2c:54:2d:ea:d4:0e Association received from mobile on AP 34:bd:c8:b3:d9:f0
*apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1697)
*apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1864)
*apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e Applying site-specific Local Bridging override for station 2c:54:2d:ea:d4:0e - vapId 3, site 'Floor_1', interface '144_v'
*apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e Applying Local Bridging Interface Policy for station 2c:54:2d:ea:d4:0e - vlan 144, interface id 12, interface '144_v'
*apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e Applying site-specific override for station 2c:54:2d:ea:d4:0e - vapId 3, site 'Floor_1', interface '144_v'
*apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1697)
*apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1864)
*apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e STA - rates (4): 130 132 139 150 0 0 0 0 0 0 0 0 0 0 0 0
*apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e STA - rates (12): 130 132 139 150 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e extSuppRates statusCode is 0 and gotExtSuppRatesElement is 1
*apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e Processing RSN IE type 48, length 22 for mobile 2c:54:2d:ea:d4:0e
*apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e CCKM: Mobile is using CCKM
*apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e Received RSN IE with 0 PMKIDs from mobile 2c:54:2d:ea:d4:0e
*apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e Setting active key cache index 8 ---> 8
*apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e unsetting PmkIdValidatedByAp
*apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e 0.0.0.0 START (0) Initializing policy
*apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state AUTHCHECK (2)
*apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state 8021X_REQD (3)
*apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e 0.0.0.0 8021X_REQD (3) DHCP Not required on AP 34:bd:c8:b3:d9:f0 vapId 3 apVapId 1for this client
*apfMsConnTask_3: Dec 07 13:55:49.524: 2c:54:2d:ea:d4:0e 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 34:bd:c8:b3:d9:f0 vapId 3 apVapId 1
*apfMsConnTask_3: Dec 07 13:55:49.524: 2c:54:2d:ea:d4:0e apfMsAssoStateInc
*apfMsConnTask_3: Dec 07 13:55:49.524: 2c:54:2d:ea:d4:0e apfPemAddUser2 (apf_policy.c:268) Changing state for mobile 2c:54:2d:ea:d4:0e on AP 34:bd:c8:b3:d9:f0 from Idle to Associated
*apfMsConnTask_3: Dec 07 13:55:49.524: 2c:54:2d:ea:d4:0e Stopping deletion of Mobile Station: (callerId: 48)
*apfMsConnTask_3: Dec 07 13:55:49.524: 2c:54:2d:ea:d4:0e Sending Assoc Response to station on BSSID 34:bd:c8:b3:d9:f0 (status 0) ApVapId 1 Slot 0
*apfMsConnTask_3: Dec 07 13:55:49.524: 2c:54:2d:ea:d4:0e apfProcessAssocReq (apf_80211.c:6290) Changing state for mobile 2c:54:2d:ea:d4:0e on AP 34:bd:c8:b3:d9:f0 from Associated to Associated
*dot1xMsgTask: Dec 07 13:55:49.525: 2c:54:2d:ea:d4:0e Disable re-auth, use PMK lifetime.
*dot1xMsgTask: Dec 07 13:55:49.525: 2c:54:2d:ea:d4:0e Station 2c:54:2d:ea:d4:0e setting dot1x reauth timeout = 65535
*dot1xMsgTask: Dec 07 13:55:49.525: 2c:54:2d:ea:d4:0e dot1x - moving mobile 2c:54:2d:ea:d4:0e into Connecting state
*dot1xMsgTask: Dec 07 13:55:49.525: 2c:54:2d:ea:d4:0e Sending EAP-Request/Identity to mobile 2c:54:2d:ea:d4:0e (EAP Id 1)
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.574: 2c:54:2d:ea:d4:0e Received EAPOL EAPPKT from mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.574: 2c:54:2d:ea:d4:0e Received Identity Response (count=1) from mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.574: 2c:54:2d:ea:d4:0e EAP State update from Connecting to Authenticating for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.574: 2c:54:2d:ea:d4:0e dot1x - moving mobile 2c:54:2d:ea:d4:0e into Authenticating state
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.574: 2c:54:2d:ea:d4:0e Entering Backend Auth Response state for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.583: 2c:54:2d:ea:d4:0e Processing Access-Challenge for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.583: 2c:54:2d:ea:d4:0e Entering Backend Auth Req state (id=85) for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.583: 2c:54:2d:ea:d4:0e WARNING: updated EAP-Identifier 1 ===> 85 for STA 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.583: 2c:54:2d:ea:d4:0e Sending EAP Request from AAA to mobile 2c:54:2d:ea:d4:0e (EAP Id 85)
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.591: 2c:54:2d:ea:d4:0e Received EAPOL EAPPKT from mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.591: 2c:54:2d:ea:d4:0e Received EAP Response from mobile 2c:54:2d:ea:d4:0e (EAP Id 85, EAP Type 3)
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.591: 2c:54:2d:ea:d4:0e Entering Backend Auth Response state for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.602: 2c:54:2d:ea:d4:0e Processing Access-Challenge for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.602: 2c:54:2d:ea:d4:0e Entering Backend Auth Req state (id=86) for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.602: 2c:54:2d:ea:d4:0e Sending EAP Request from AAA to mobile 2c:54:2d:ea:d4:0e (EAP Id 86)
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.621: 2c:54:2d:ea:d4:0e Received EAPOL EAPPKT from mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.621: 2c:54:2d:ea:d4:0e Received EAP Response from mobile 2c:54:2d:ea:d4:0e (EAP Id 86, EAP Type 43)
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.621: 2c:54:2d:ea:d4:0e Entering Backend Auth Response state for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.625: 2c:54:2d:ea:d4:0e Processing Access-Challenge for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.625: 2c:54:2d:ea:d4:0e Entering Backend Auth Req state (id=87) for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.625: 2c:54:2d:ea:d4:0e Sending EAP Request from AAA to mobile 2c:54:2d:ea:d4:0e (EAP Id 87)
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.653: 2c:54:2d:ea:d4:0e Received EAPOL EAPPKT from mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.653: 2c:54:2d:ea:d4:0e Received EAP Response from mobile 2c:54:2d:ea:d4:0e (EAP Id 87, EAP Type 43)
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.653: 2c:54:2d:ea:d4:0e Entering Backend Auth Response state for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.655: 2c:54:2d:ea:d4:0e Processing Access-Challenge for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.655: 2c:54:2d:ea:d4:0e Entering Backend Auth Req state (id=89) for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.655: 2c:54:2d:ea:d4:0e WARNING: updated EAP-Identifier 87 ===> 89 for STA 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.655: 2c:54:2d:ea:d4:0e Sending EAP Request from AAA to mobile 2c:54:2d:ea:d4:0e (EAP Id 89)
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.671: 2c:54:2d:ea:d4:0e Received EAPOL EAPPKT from mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.671: 2c:54:2d:ea:d4:0e Received EAP Response from mobile 2c:54:2d:ea:d4:0e (EAP Id 89, EAP Type 43)
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.671: 2c:54:2d:ea:d4:0e Entering Backend Auth Response state for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.676: 2c:54:2d:ea:d4:0e Processing Access-Challenge for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.676: 2c:54:2d:ea:d4:0e Entering Backend Auth Req state (id=90) for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.676: 2c:54:2d:ea:d4:0e Sending EAP Request from AAA to mobile 2c:54:2d:ea:d4:0e (EAP Id 90)
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.691: 2c:54:2d:ea:d4:0e Received EAPOL EAPPKT from mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.691: 2c:54:2d:ea:d4:0e Received EAP Response from mobile 2c:54:2d:ea:d4:0e (EAP Id 90, EAP Type 43)
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.691: 2c:54:2d:ea:d4:0e Entering Backend Auth Response state for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.702: 2c:54:2d:ea:d4:0e Processing Access-Accept for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Resetting web IPv4 acl from 255 to 255
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Username entry (test960) created for mobile, length = 253
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Username entry (test960) created in mscb for mobile, length = 253
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Setting re-auth timeout to 65535 seconds, got from WLAN config.
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Station 2c:54:2d:ea:d4:0e setting dot1x reauth timeout = 65535
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Creating a PKC PMKID Cache entry for station 2c:54:2d:ea:d4:0e (RSN 2)
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Resetting MSCB PMK Cache Entry 0 for station 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Setting active key cache index 8 ---> 8
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Setting active key cache index 8 ---> 0
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Adding BSSID 34:bd:c8:b3:d9:f0 to PMKID cache at index 0 for station 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: New PMKID: (16)
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: [0000] ab 8f b5 75 ad c5 8e af 50 0d ce 4a f1 7b 16 9e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Disabling re-auth since PMK lifetime can take care of same.
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e CCKM: Create a global PMK cache entry
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e unsetting PmkIdValidatedByAp
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Sending EAP-Success to mobile 2c:54:2d:ea:d4:0e (EAP Id 90)
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Found an cache entry for BSSID 34:bd:c8:b3:d9:f0 in PMKID cache at index 0 of station 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Found an cache entry for BSSID 34:bd:c8:b3:d9:f0 in PMKID cache at index 0 of station 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: Including PMKID in M1 (16)
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: [0000] ab 8f b5 75 ad c5 8e af 50 0d ce 4a f1 7b 16 9e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Starting key exchange to mobile 2c:54:2d:ea:d4:0e, data packets will be dropped
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Sending EAPOL-Key Message to mobile 2c:54:2d:ea:d4:0e
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Entering Backend Auth Success state (id=90) for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Received Auth Success while in Authenticating state for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.704: 2c:54:2d:ea:d4:0e dot1x - moving mobile 2c:54:2d:ea:d4:0e into Authenticated state
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.721: 2c:54:2d:ea:d4:0e Received EAPOL-Key from mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.721: 2c:54:2d:ea:d4:0e Received EAPOL-key in PTK_START state (message 2) from mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.721: 2c:54:2d:ea:d4:0e CCKM: Sending cache add
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.721: CCKM: Sending CCKM PMK (Version_1) information to mobility group
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.721: CCKM: Sending CCKM PMK (Version_2) information to mobility group
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.721: 2c:54:2d:ea:d4:0e Stopping retransmission timer for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.721: 2c:54:2d:ea:d4:0e Sending EAPOL-Key Message to mobile 2c:54:2d:ea:d4:0e
state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.741: 2c:54:2d:ea:d4:0e Received EAPOL-Key from mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.741: 2c:54:2d:ea:d4:0e Received EAPOL-key in PTKINITNEGOTIATING state (message 4) from mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.741: 2c:54:2d:ea:d4:0e apfMs1xStateInc
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.741: 2c:54:2d:ea:d4:0e 0.0.0.0 8021X_REQD (3) Change state to L2AUTHCOMPLETE (4) last state L2AUTHCOMPLETE (4)
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.741: 2c:54:2d:ea:d4:0e 0.0.0.0 L2AUTHCOMPLETE (4) DHCP Not required on AP 34:bd:c8:b3:d9:f0 vapId 3 apVapId 1for this client
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.741: 2c:54:2d:ea:d4:0e 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 34:bd:c8:b3:d9:f0 vapId 3 apVapId 1
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.741: 2c:54:2d:ea:d4:0e 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state DHCP_REQD (7)
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.741: 2c:54:2d:ea:d4:0e 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 5253, Adding TMP rule
*Dot1x_NW_MsgTask_: Dec 07 13:55:49.741: 2c:54:2d:ea:d4:0e 0.0.0.0 DHCP_REQD (7) Adding Fast Path rule
type = Airespace AP - Learn IP address
on AP 34:bd:c8:b3:d9:f0, slot 0, interface = 1, QOS = 2
IPv4 ACL ID = 255, IPv
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.741: 2c:54:2d:ea:d4:0e 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 7006 Local Bridging Vlan = 144, Local Bridging intf id = 12
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.741: 2c:54:2d:ea:d4:0e 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255)
*Dot1x_NW_MsgTask_6: Dec 07 13:55:49.741: 2c:54:2d:ea:d4:0e Stopping retransmission timer for mobile 2c:54:2d:ea:d4:0e
*apfReceiveTask: Dec 07 13:55:49.741: 2c:54:2d:ea:d4:0e 0.0.0.0 DHCP_REQD (7) State Update from Mobility-Incomplete to Mobility-Complete, mobility role=Local, client state=APF_MS_STATE_ASSOCIATED
*apfReceiveTask: Dec 07 13:55:49.741: 2c:54:2d:ea:d4:0e 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 4891, Adding TMP rule
*apfReceiveTask: Dec 07 13:55:49.742: 2c:54:2d:ea:d4:0e 0.0.0.0 DHCP_REQD (7) Replacing Fast Path rule
type = Airespace AP - Learn IP address
on AP 34:bd:c8:b3:d9:f0, slot 0, interface = 1, QOS = 2
IPv4 ACL ID = 255,
*apfReceiveTask: Dec 07 13:55:49.742: 2c:54:2d:ea:d4:0e 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 7006 Local Bridging Vlan = 144, Local Bridging intf id = 12
*apfReceiveTask: Dec 07 13:55:49.742: 2c:54:2d:ea:d4:0e 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255)
*pemReceiveTask: Dec 07 13:55:49.742: 2c:54:2d:ea:d4:0e 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
*pemReceiveTask: Dec 07 13:55:49.742: 2c:54:2d:ea:d4:0e Sent an XID frame
*pemReceiveTask: Dec 07 13:55:49.742: 2c:54:2d:ea:d4:0e 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
*pemReceiveTask: Dec 07 13:55:49.742: 2c:54:2d:ea:d4:0e Sent an XID frame
*DHCP Socket Task: Dec 07 13:55:50.513: 2c:54:2d:ea:d4:0e DHCP received op BOOTREQUEST (1) (len 556,vlan 0, port 1, encap 0xec03)
*DHCP Socket Task: Dec 07 13:55:50.513: 2c:54:2d:ea:d4:0e DHCP selecting relay 1 - control block settings:
dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
dhcpGateway: 0.0.0.0, dhcpRelay: 0.0.0.0 VLAN: 0
*DHCP Socket Task: Dec 07 13:55:50.513: 2c:54:2d:ea:d4:0e DHCP selected relay 1 - 172.16.100.121 (local address 10.123.200.15, gateway 10.123.200.1, VLAN 144, port 1)
*DHCP Socket Task: Dec 07 13:55:50.513: 2c:54:2d:ea:d4:0e DHCP transmitting DHCP DISCOVER (1)
*DHCP Socket Task: Dec 07 13:55:50.513: 2c:54:2d:ea:d4:0e DHCP op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 1
*DHCP Socket Task: Dec 07 13:55:50.513: 2c:54:2d:ea:d4:0e DHCP xid: 0xf12d461 (252892257), secs: 0, flags: 0
*DHCP Socket Task: Dec 07 13:55:50.514: 2c:54:2d:ea:d4:0e DHCP chaddr: 2c:54:2d:ea:d4:0e
*DHCP Socket Task: Dec 07 13:55:50.514: 2c:54:2d:ea:d4:0e DHCP ciaddr: 0.0.0.0, yiaddr: 0.0.0.0
*DHCP Socket Task: Dec 07 13:55:50.514: 2c:54:2d:ea:d4:0e DHCP siaddr: 0.0.0.0, giaddr: 10.123.200.15
*DHCP Socket Task: Dec 07 13:55:50.514: 2c:54:2d:ea:d4:0e DHCP requested ip: 10.123.205.33
*DHCP Socket Task: Dec 07 13:55:50.514: 2c:54:2d:ea:d4:0e DHCP ARPing for 10.123.200.1 (SPA 10.123.200.15, vlanId 144)
*DHCP Socket Task: Dec 07 13:55:50.514: 2c:54:2d:ea:d4:0e DHCP selecting relay 2 - control block settings:
dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
dhcpGateway: 0.0.0.0, dhcpRelay: 10.123.200.15 VLAN: 144
*DHCP Socket Task: Dec 07 13:55:50.514: 2c:54:2d:ea:d4:0e DHCP selected relay 2 - 172.16.100.122 (local address 10.123.200.15, gateway 10.123.200.1, VLAN 144, port 1)
*DHCP Socket Task: Dec 07 13:55:50.514: 2c:54:2d:ea:d4:0e DHCP transmitting DHCP DISCOVER (1)
*DHCP Socket Task: Dec 07 13:55:50.514: 2c:54:2d:ea:d4:0e DHCP op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 2
*DHCP Socket Task: Dec 07 13:55:50.514: 2c:54:2d:ea:d4:0e DHCP xid: 0xf12d461 (252892257), secs: 0, flags: 0
*DHCP Socket Task: Dec 07 13:55:50.514: 2c:54:2d:ea:d4:0e DHCP chaddr: 2c:54:2d:ea:d4:0e
*DHCP Socket Task: Dec 07 13:55:50.514: 2c:54:2d:ea:d4:0e DHCP ciaddr: 0.0.0.0, yiaddr: 0.0.0.0
*DHCP Socket Task: Dec 07 13:55:50.514: 2c:54:2d:ea:d4:0e DHCP siaddr: 0.0.0.0, giaddr: 10.123.200.15
*DHCP Socket Task: Dec 07 13:55:50.514: 2c:54:2d:ea:d4:0e DHCP requested ip: 10.123.205.33
*DHCP Socket Task: Dec 07 13:55:50.514: 2c:54:2d:ea:d4:0e DHCP ARPing for 10.123.200.1 (SPA 10.123.200.15, vlanId 144)
*DHCP Socket Task: Dec 07 13:55:52.512: 2c:54:2d:ea:d4:0e DHCP received op BOOTREQUEST (1) (len 556,vlan 0, port 1, encap 0xec03)
*DHCP Socket Task: Dec 07 13:55:52.512: 2c:54:2d:ea:d4:0e DHCP selecting relay 1 - control block settings:
dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
dhcpGateway: 0.0.0.0, dhcpRelay: 10.123.200.15 VLAN: 144
*DHCP Socket Task: Dec 07 13:55:52.512: 2c:54:2d:ea:d4:0e DHCP selected relay 1 - 172.16.100.121 (local address 10.123.200.15, gateway 10.123.200.1, VLAN 144, port 1)
*DHCP Socket Task: Dec 07 13:55:52.512: 2c:54:2d:ea:d4:0e DHCP transmitting DHCP DISCOVER (1)
*DHCP Socket Task: Dec 07 13:55:52.512: 2c:54:2d:ea:d4:0e DHCP op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 1
*DHCP Socket Task: Dec 07 13:55:52.512: 2c:54:2d:ea:d4:0e DHCP xid: 0xf12d461 (252892257), secs: 0, flags: 0
*DHCP Socket Task: Dec 07 13:55:52.512: 2c:54:2d:ea:d4:0e DHCP chaddr: 2c:54:2d:ea:d4:0e
*DHCP Socket Task: Dec 07 13:55:52.512: 2c:54:2d:ea:d4:0e DHCP ciaddr: 0.0.0.0, yiaddr: 0.0.0.0
*DHCP Socket Task: Dec 07 13:55:52.512: 2c:54:2d:ea:d4:0e DHCP siaddr: 0.0.0.0, giaddr: 10.123.200.15
*DHCP Socket Task: Dec 07 13:55:52.512: 2c:54:2d:ea:d4:0e DHCP requested ip: 10.123.205.33
*DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP sending REQUEST to 10.123.200.1 (len 374, port 1, vlan 144)
*DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP selecting relay 2 - control block settings:
dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
dhcpGateway: 0.0.0.0, dhcpRelay: 10.123.200.15 VLAN: 144
*DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP selected relay 2 - 172.16.100.122 (local address 10.123.200.15, gateway 10.123.200.1, VLAN 144, port 1)
*DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP transmitting DHCP DISCOVER (1)
*DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 2
*DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP xid: 0xf12d461 (252892257), secs: 0, flags: 0
*DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP chaddr: 2c:54:2d:ea:d4:0e
*DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP ciaddr: 0.0.0.0, yiaddr: 0.0.0.0
*DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP siaddr: 0.0.0.0, giaddr: 10.123.200.15
*DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP requested ip: 10.123.205.33
*DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP sending REQUEST to 10.123.200.1 (len 374, port 1, vlan 144)
*DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP received op BOOTREPLY (2) (len 322,vlan 144, port 1, encap 0xec00)
*DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP setting server from OFFER (server 172.16.100.121, yiaddr 10.123.201.4)
*DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP sending REPLY to STA (len 430, port 1, vlan 0)
*DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP transmitting DHCP OFFER (2)
*DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP op: BOOTREPLY, htype: Ethernet, hlen: 6, hops: 0
*DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP xid: 0xf12d461 (252892257), secs: 0, flags: 0
*DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP chaddr: 2c:54:2d:ea:d4:0e
*DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP ciaddr: 0.0.0.0, yiaddr: 10.123.201.4
*DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP siaddr: 0.0.0.0, giaddr: 0.0.0.0
*DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP server id: 1.1.1.1 rcvd server id: 172.16.100.121
*DHCP Socket Task: Dec 07 13:55:52.514: 2c:54:2d:ea:d4:0e DHCP received op BOOTREPLY (2) (len 322,vlan 144, port 1, encap 0xec00)
*DHCP Socket Task: Dec 07 13:55:52.514: 2c:54:2d:ea:d4:0e DHCP dropping OFFER from 172.16.100.122 (yiaddr 10.123.205.33)
*DHCP Socket Task: Dec 07 13:55:52.523: 2c:54:2d:ea:d4:0e DHCP received op BOOTREQUEST (1) (len 556,vlan 0, port 1, encap 0xec03)
*DHCP Socket Task: Dec 07 13:55:52.523: 2c:54:2d:ea:d4:0e DHCP selecting relay 1 - control block settings:
dhcpServer: 172.16.100.121, dhcpNetmask: 0.0.0.0,
dhcpGateway: 0.0.0.0, dhcpRelay: 10.123.200.15 VLAN: 144
*DHCP Socket Task: Dec 07 13:55:52.523: 2c:54:2d:ea:d4:0e DHCP selected relay 1 - 172.16.100.121 (local address 10.123.200.15, gateway 10.123.200.1, VLAN 144, port 1)
*DHCP Socket Task: Dec 07 13:55:52.523: 2c:54:2d:ea:d4:0e DHCP transmitting DHCP REQUEST (3)
*DHCP Socket Task: Dec 07 13:55:52.524: 2c:54:2d:ea:d4:0e DHCP op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 1
*DHCP Socket Task: Dec 07 13:55:52.524: 2c:54:2d:ea:d4:0e DHCP xid: 0xf12d461 (252892257), secs: 0, flags: 0
*DHCP Socket Task: Dec 07 13:55:52.524: 2c:54:2d:ea:d4:0e DHCP chaddr: 2c:54:2d:ea:d4:0e
*DHCP Socket Task: Dec 07 13:55:52.524: 2c:54:2d:ea:d4:0e DHCP ciaddr: 0.0.0.0, yiaddr: 0.0.0.0
*DHCP Socket Task: Dec 07 13:55:52.524: 2c:54:2d:ea:d4:0e DHCP siaddr: 0.0.0.0, giaddr: 10.123.200.15
*DHCP Socket Task: Dec 07 13:55:52.524: 2c:54:2d:ea:d4:0e DHCP requested ip: 10.123.201.4
*DHCP Socket Task: Dec 07 13:55:52.524: 2c:54:2d:ea:d4:0e DHCP server id: 172.16.100.121 rcvd server id: 1.1.1.1
*DHCP Socket Task: Dec 07 13:55:52.524: 2c:54:2d:ea:d4:0e DHCP sending REQUEST to 10.123.200.1 (len 382, port 1, vlan 144)
*DHCP Socket Task: Dec 07 13:55:52.524: 2c:54:2d:ea:d4:0e DHCP selecting relay 2 - control block settings:
dhcpServer: 172.16.100.121, dhcpNetmask: 0.0.0.0,
dhcpGateway: 0.0.0.0, dhcpRelay: 10.123.200.15 VLAN: 144
*DHCP Socket Task: Dec 07 13:55:52.524: 2c:54:2d:ea:d4:0e DHCP selected relay 2 - NONE
*DHCP Socket Task: Dec 07 13:55:52.524: 2c:54:2d:ea:d4:0e DHCP received op BOOTREPLY (2) (len 322,vlan 144, port 1, encap 0xec00)
*DHCP Socket Task: Dec 07 13:55:52.525: 2c:54:2d:ea:d4:0e Static IP client associated to interface 144_v which can support client subnet.
*DHCP Socket Task: Dec 07 13:55:52.525: 2c:54:2d:ea:d4:0e apfMsRunStateInc
*DHCP Socket Task: Dec 07 13:55:52.525: 2c:54:2d:ea:d4:0e 10.123.201.4 DHCP_REQD (7) Change state to RUN (20) last state RUN (20)
*DHCP Socket Task: Dec 07 13:55:52.526: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Reached PLUMBFASTPATH: from line 5776
*DHCP Soc: Dec 07 13:55:52.526: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Replacing Fast Path rule
type = Airespace AP Client
on AP 34:bd:c8:b3:d9:f0, slot 0, interface = 1, QOS = 2
IPv4 ACL ID = 255, IPv6 ACL ID
*DHCP Socket Task: Dec 07 13:55:52.526: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 7006 Local Bridging Vlan = 144, Local Bridging intf id = 12
*DHCP Socket Task: Dec 07 13:55:52.526: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255)
*DHCP Socket Task: Dec 07 13:55:52.526: 2c:54:2d:ea:d4:0e Assigning Address 10.123.201.4 to mobile
*DHCP Socket Task: Dec 07 13:55:52.526: 2c:54:2d:ea:d4:0e DHCP success event for client. Clearing dhcp failure count for interface 144_v.
*DHCP Socket Task: Dec 07 13:55:52.526: 2c:54:2d:ea:d4:0e DHCP sending REPLY to STA (len 430, port 1, vlan 0)
*DHCP Socket Task: Dec 07 13:55:52.526: 2c:54:2d:ea:d4:0e DHCP transmitting DHCP ACK (5)
*DHCP Socket Task: Dec 07 13:55:52.526: 2c:54:2d:ea:d4:0e DHCP op: BOOTREPLY, htype: Ethernet, hlen: 6, hops: 0
*DHCP Socket Task: Dec 07 13:55:52.526: 2c:54:2d:ea:d4:0e DHCP xid: 0xf12d461 (252892257), secs: 0, flags: 0
*DHCP Socket Task: Dec 07 13:55:52.526: 2c:54:2d:ea:d4:0e DHCP chaddr: 2c:54:2d:ea:d4:0e
*DHCP Socket Task: Dec 07 13:55:52.526: 2c:54:2d:ea:d4:0e DHCP ciaddr: 0.0.0.0, yiaddr: 10.123.201.4
*DHCP Socket Task: Dec 07 13:55:52.526: 2c:54:2d:ea:d4:0e DHCP siaddr: 0.0.0.0, giaddr: 0.0.0.0
*DHCP Socket Task: Dec 07 13:55:52.527: 2c:54:2d:ea:d4:0e DHCP server id: 1.1.1.1 rcvd server id: 172.16.100.121
*pemReceiveTask: Dec 07 13:55:52.527: 2c:54:2d:ea:d4:0e 10.123.201.4 Added NPU entry of type 1, dtlFlags 0x10
*pemReceiveTask: Dec 07 13:55:52.527: 2c:54:2d:ea:d4:0e Sending a gratuitous ARP for 10.123.201.4, VLAN Id 144
*apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e Association received from mobile on AP 34:bd:c8:b3:d9:f0
*apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1697)
*apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1864)
*apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e Applying site-specific Local Bridging override for station 2c:54:2d:ea:d4:0e - vapId 3, site 'Floor_1', interface '144_v'
*apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e Applying Local Bridging Interface Policy for station 2c:54:2d:ea:d4:0e - vlan 144, interface id 12, interface '144_v'
*apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e Applying site-specific override for station 2c:54:2d:ea:d4:0e - vapId 3, site 'Floor_1', interface '144_v'
*apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1697)
*apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1864)
*apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e STA - rates (4): 130 132 139 150 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e STA - rates (12): 130 132 139 150 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e extSuppRates statusCode is 0 and gotExtSuppRatesElement is 1
*apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e Processing RSN IE type 48, length 22 for mobile 2c:54:2d:ea:d4:0e
*apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e CCKM: Mobile is using CCKM
*apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e Received RSN IE with 0 PMKIDs from mobile 2c:54:2d:ea:d4:0e
*apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e Found an cache entry for BSSID 34:bd:c8:b3:d9:f0 in PMKID cache at index 0 of station 2c:54:2d:ea:d4:0e
*apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e Removing BSSID 34:bd:c8:b3:d9:f0 from PMKID cache of station 2c:54:2d:ea:d4:0e
*apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e Resetting MSCB PMK Cache Entry 0 for station 2c:54:2d:ea:d4:0e
*apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e Setting active key cache index 0 ---> 8
*apfMsConnTask_3: Dec 07 13:57:01.510: 2c:54:2d:ea:d4:0e unsetting PmkIdValidatedByAp
*apfMsConnTask_3: Dec 07 13:57:01.510: 2c:54:2d:ea:d4:0e apfMsRunStateDec
*apfMsConnTask_3: Dec 07 13:57:01.510: 2c:54:2d:ea:d4:0e apfMs1xStateDec
*apfMsConnTask_3: Dec 07 13:57:01.510: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Change state to START (0) last state RUN (20)
*apfMsConnTask_3: Dec 07 13:57:01.510: 2c:54:2d:ea:d4:0e pemApfAddMobileStation2: APF_MS_PEM_WAIT_L2_AUTH_COMPLETE = 0.
*apfMsConnTask_3: Dec 07 13:57:01.510: 2c:54:2d:ea:d4:0e 10.123.201.4 START (0) Initializing policy
*apfMsConnTask_3: Dec 07 13:57:01.510: 2c:54:2d:ea:d4:0e 10.123.201.4 START (0) Change state to AUTHCHECK (2) last state RUN (20)
*apfMsConnTask_3: Dec 07 13:57:01.510: 2c:54:2d:ea:d4:0e 10.123.201.4 AUTHCHECK (2) Change state to 8021X_REQD (3) last state RUN (20)
*apfMsConnTask_3: Dec 07 13:57:01.510: 2c:54:2d:ea:d4:0e 10.123.201.4 8021X_REQD (3) DHCP required on AP 34:bd:c8:b3:d9:f0 vapId 3 apVapId 1for this client
*apfMsConnTask_3: Dec 07 13:57:01.510: 2c:54:2d:ea:d4:0e 10.123.201.4 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 34:bd:c8:b3:d9:f0 vapId 3 apVapId 1
*apfMsConnTask_3: Dec 07 13:57:01.510: 2c:54:2d:ea:d4:0e apfPemAddUser2 (apf_policy.c:268) Changing state for mobile 2c:54:2d:ea:d4:0e on AP 34:bd:c8:b3:d9:f0 from Associated to Associated
*apfMsConnTask_3: Dec 07 13:57:01.510: 2c:54:2d:ea:d4:0e Stopping deletion of Mobile Station: (callerId: 48)
*apfMsConnTask_3: Dec 07 13:57:01.510: 2c:54:2d:ea:d4:0e Sending Assoc Response to station on BSSID 34:bd:c8:b3:d9:f0 (status 0) ApVapId 1 Slot 0
*apfMsConnTask_3: Dec 07 13:57:01.510: 2c:54:2d:ea:d4:0e apfProcessAssocReq (apf_80211.c:6290) Changing state for mobile 2c:54:2d:ea:d4:0e on AP 34:bd:c8:b3:d9:f0 from Associated to Associated
*dot1xMsgTask: Dec 07 13:57:01.512: 2c:54:2d:ea:d4:0e Disable re-auth, use PMK lifetime.
*dot1xMsgTask: Dec 07 13:57:01.512: 2c:54:2d:ea:d4:0e dot1x - moving mobile 2c:54:2d:ea:d4:0e into Connecting state
*dot1xMsgTask: Dec 07 13:57:01.512: 2c:54:2d:ea:d4:0e Sending EAP-Request/Identity to mobile 2c:54:2d:ea:d4:0e (EAP Id 1)
*pemReceiveTask: Dec 07 13:57:01.513: 2c:54:2d:ea:d4:0e 10.123.201.4 Removed NPU entry.
*Dot1x_NW_MsgTask_6: Dec 07 13:57:01.654: 2c:54:2d:ea:d4:0e Received EAPOL EAPPKT from mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:01.654: 2c:54:2d:ea:d4:0e Received Identity Response (count=1) from mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:01.654: 2c:54:2d:ea:d4:0e EAP State update from Connecting to Authenticating for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:01.654: 2c:54:2d:ea:d4:0e dot1x - moving mobile 2c:54:2d:ea:d4:0e into Authenticating state
*Dot1x_NW_MsgTask_6: Dec 07 13:57:01.654: 2c:54:2d:ea:d4:0e Entering Backend Auth Response state for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:01.684: 2c:54:2d:ea:d4:0e Processing Access-Challenge for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:01.684: 2c:54:2d:ea:d4:0e Entering Backend Auth Req state (id=86) for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:01.684: 2c:54:2d:ea:d4:0e WARNING: updated EAP-Identifier 1 ===> 86 for STA 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:01.684: 2c:54:2d:ea:d4:0e Sending EAP Request from AAA to mobile 2c:54:2d:ea:d4:0e (EAP Id 86)
*Dot1x_NW_MsgTask_6: Dec 07 13:57:01.695: 2c:54:2d:ea:d4:0e Received EAPOL EAPPKT from mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:01.695: 2c:54:2d:ea:d4:0e Received EAP Response from mobile 2c:54:2d:ea:d4:0e (EAP Id 86, EAP Type 3)
*Dot1x_NW_MsgTask_6: Dec 07 13:57:01.695: 2c:54:2d:ea:d4:0e Entering Backend Auth Response state for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:01.699: 2c:54:2d:ea:d4:0e Processing Access-Challenge for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:01.699: 2c:54:2d:ea:d4:0e Entering Backend Auth Req state (id=87) for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:01.699: 2c:54:2d:ea:d4:0e Sending EAP Request from AAA to mobile 2c:54:2d:ea:d4:0e (EAP Id 87)
*Dot1x_NW_MsgTask_6: Dec 07 13:57:01.806: 2c:54:2d:ea:d4:0e Received EAPOL EAPPKT from mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:01.806: 2c:54:2d:ea:d4:0e Received EAP Response from mobile 2c:54:2d:ea:d4:0e (EAP Id 87, EAP Type 43)
*Dot1x_NW_MsgTask_6: Dec 07 13:57:01.806: 2c:54:2d:ea:d4:0e Entering Backend Auth Response state for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:01.809: 2c:54:2d:ea:d4:0e Processing Access-Challenge for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:01.809: 2c:54:2d:ea:d4:0e Entering Backend Auth Req state (id=88) for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:01.809: 2c:54:2d:ea:d4:0e Sending EAP Request from AAA to mobile 2c:54:2d:ea:d4:0e (EAP Id 88)
*Dot1x_NW_MsgTask_6: Dec 07 13:57:01.874: 2c:54:2d:ea:d4:0e Received EAPOL EAPPKT from mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:01.874: 2c:54:2d:ea:d4:0e Received EAP Response from mobile 2c:54:2d:ea:d4:0e (EAP Id 88, EAP Type 43)
*Dot1x_NW_MsgTask_6: Dec 07 13:57:01.874: 2c:54:2d:ea:d4:0e Entering Backend Auth Response state for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:01.880: 2c:54:2d:ea:d4:0e Processing Access-Challenge for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:01.880: 2c:54:2d:ea:d4:0e Entering Backend Auth Req state (id=90) for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:01.880: 2c:54:2d:ea:d4:0e WARNING: updated EAP-Identifier 88 ===> 90 for STA 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:01.880: 2c:54:2d:ea:d4:0e Sending EAP Request from AAA to mobile 2c:54:2d:ea:d4:0e (EAP Id 90)
*Dot1x_NW_MsgTask_6: Dec 07 13:57:01.903: 2c:54:2d:ea:d4:0e Received EAPOL EAPPKT from mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:01.903: 2c:54:2d:ea:d4:0e Received EAP Response from mobile 2c:54:2d:ea:d4:0e (EAP Id 90, EAP Type 43)
*Dot1x_NW_MsgTask_6: Dec 07 13:57:01.903: 2c:54:2d:ea:d4:0e Entering Backend Auth Response state for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:01.909: 2c:54:2d:ea:d4:0e Processing Access-Challenge for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:01.909: 2c:54:2d:ea:d4:0e Entering Backend Auth Req state (id=91) for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:01.909: 2c:54:2d:ea:d4:0e Sending EAP Request from AAA to mobile 2c:54:2d:ea:d4:0e (EAP Id 91)
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.061: 2c:54:2d:ea:d4:0e Received EAPOL EAPPKT from mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.061: 2c:54:2d:ea:d4:0e Received EAP Response from mobile 2c:54:2d:ea:d4:0e (EAP Id 91, EAP Type 43)
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.061: 2c:54:2d:ea:d4:0e Entering Backend Auth Response state for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.076: 2c:54:2d:ea:d4:0e Processing Access-Accept for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.076: 2c:54:2d:ea:d4:0e Resetting web IPv4 acl from 255 to 255
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.076: 2c:54:2d:ea:d4:0e Setting re-auth timeout to 65535 seconds, got from WLAN config.
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: 2c:54:2d:ea:d4:0e Station 2c:54:2d:ea:d4:0e setting dot1x reauth timeout = 65535
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: 2c:54:2d:ea:d4:0e Creating a PKC PMKID Cache entry for station 2c:54:2d:ea:d4:0e (RSN 2)
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: 2c:54:2d:ea:d4:0e Resetting MSCB PMK Cache Entry 0 for station 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: 2c:54:2d:ea:d4:0e Setting active key cache index 8 ---> 8
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: 2c:54:2d:ea:d4:0e Setting active key cache index 8 ---> 0
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: 2c:54:2d:ea:d4:0e Adding BSSID 34:bd:c8:b3:d9:f0 to PMKID cache at index 0 for station 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: New PMKID: (16)
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: [0000] 16 bf c0 3e 07 00 79 b1 51 ca d3 47 44 69 1b a1
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: 2c:54:2d:ea:d4:0e Disabling re-auth since PMK lifetime can take care of same.
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: 2c:54:2d:ea:d4:0e CCKM: Create a global PMK cache entry
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: 2c:54:2d:ea:d4:0e unsetting PmkIdValidatedByAp
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: 2c:54:2d:ea:d4:0e Sending EAP-Success to mobile 2c:54:2d:ea:d4:0e (EAP Id 91)
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: 2c:54:2d:ea:d4:0e Found an cache entry for BSSID 34:bd:c8:b3:d9:f0 in PMKID cache at index 0 of station 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: 2c:54:2d:ea:d4:0e Found an cache entry for BSSID 34:bd:c8:b3:d9:f0 in PMKID cache at index 0 of station 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: Including PMKID in M1 (16)
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: [0000] 16 bf c0 3e 07 00 79 b1 51 ca d3 47 44 69 1b a1
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: 2c:54:2d:ea:d4:0e Starting key exchange to mobile 2c:54:2d:ea:d4:0e, data packets will be dropped
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: 2c:54:2d:ea:d4:0e Sending EAPOL-Key Message to mobile 2c:54:2d:ea:d4:0e
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: 2c:54:2d:ea:d4:0e Entering Backend Auth Success state (id=91) for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: 2c:54:2d:ea:d4:0e Received Auth Success while in Authenticating state for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: 2c:54:2d:ea:d4:0e dot1x - moving mobile 2c:54:2d:ea:d4:0e into Authenticated state
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.113: 2c:54:2d:ea:d4:0e Received EAPOL-Key from mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.113: 2c:54:2d:ea:d4:0e Received EAPOL-key in PTK_START state (message 2) from mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.113: 2c:54:2d:ea:d4:0e CCKM: Sending cache add
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.113: CCKM: Sending CCKM PMK (Version_1) information to mobility group
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.113: CCKM: Sending CCKM PMK (Version_2) information to mobility group
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.113: 2c:54:2d:ea:d4:0e Stopping retransmission timer for mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.113: 2c:54:2d:ea:d4:0e Sending EAPOL-Key Message to mobile 2c:54:2d:ea:d4:0e
state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.164: 2c:54:2d:ea:d4:0e Received EAPOL-Key from mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.164: 2c:54:2d:ea:d4:0e Received EAPOL-key in PTKINITNEGOTIATING state (message 4) from mobile 2c:54:2d:ea:d4:0e
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.164: 2c:54:2d:ea:d4:0e apfMs1xStateInc
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.164: 2c:54:2d:ea:d4:0e 10.123.201.4 8021X_REQD (3) Change state to L2AUTHCOMPLETE (4) last state RUN (20)
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.164: 2c:54:2d:ea:d4:0e 10.123.201.4 L2AUTHCOMPLETE (4) DHCP required on AP 34:bd:c8:b3:d9:f0 vapId 3 apVapId 1for this client
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.164: 2c:54:2d:ea:d4:0e 10.123.201.4 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 34:bd:c8:b3:d9:f0 vapId 3 apVapId 1
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.164: 2c:54:2d:ea:d4:0e apfMsRunStateInc
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.164: 2c:54:2d:ea:d4:0e 10.123.201.4 L2AUTHCOMPLETE (4) Change state to RUN (20) last state RUN (20)
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.166: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Reached PLUMBFASTPATH: from line 5362
*Dot1x: Dec 07 13:57:02.166: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Adding Fast Path rule
type = Airespace AP Client
on AP 34:bd:c8:b3:d9:f0, slot 0, interface = 1, QOS = 2
IPv4 ACL ID = 255, IPv6 ACL ID = 2
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.166: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 7006 Local Bridging Vlan = 144, Local Bridging intf id = 12
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.166: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255)
*Dot1x_NW_MsgTask_6: Dec 07 13:57:02.166: 2c:54:2d:ea:d4:0e Stopping retransmission timer for mobile 2c:54:2d:ea:d4:0e
*pemReceiveTask: Dec 07 13:57:02.166: 2c:54:2d:ea:d4:0e 10.123.201.4 Added NPU entry of type 1, dtlFlags 0x0
*apfMsConnTask_2: Dec 07 13:57:03.265: 2c:54:2d:ea:d4:0e CCKM: Received REASSOC REQ IE
*apfMsConnTask_2: Dec 07 13:57:03.265: 2c:54:2d:ea:d4:0e Reassociation received from mobile on AP 34:bd:c8:b2:b1:10
*apfMsConnTask_2: Dec 07 13:57:03.265: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1697)
*apfMsConnTask_2: Dec 07 13:57:03.265: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1864)
*apfMsConnTask_2: Dec 07 13:57:03.265: 2c:54:2d:ea:d4:0e Applying site-specific Local Bridging override for station 2c:54:2d:ea:d4:0e - vapId 3, site 'Floor_1', interface '144_v'
*apfMsConnTask_2: Dec 07 13:57:03.265: 2c:54:2d:ea:d4:0e Applying Local Bridging Interface Policy for station 2c:54:2d:ea:d4:0e - vlan 144, interface id 12, interface '144_v'
*apfMsConnTask_2: Dec 07 13:57:03.265: 2c:54:2d:ea:d4:0e Applying site-specific override for station 2c:54:2d:ea:d4:0e - vapId 3, site 'Floor_1', interface '144_v'
*apfMsConnTask_2: Dec 07 13:57:03.265: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1697)
*apfMsConnTask_2: Dec 07 13:57:03.265: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1864)
*apfMsConnTask_2: Dec 07 13:57:03.265: 2c:54:2d:ea:d4:0e processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_2: Dec 07 13:57:03.265: 2c:54:2d:ea:d4:0e processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_2: Dec 07 13:57:03.266: 2c:54:2d:ea:d4:0e STA - rates (4): 130 132 139 150 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_2: Dec 07 13:57:03.266: 2c:54:2d:ea:d4:0e suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_2: Dec 07 13:57:03.266: 2c:54:2d:ea:d4:0e STA - rates (12): 130 132 139 150 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_2: Dec 07 13:57:03.266: 2c:54:2d:ea:d4:0e extSuppRates statusCode is 0 and gotExtSuppRatesElement is 1
*apfMsConnTask_2: Dec 07 13:57:03.266: 2c:54:2d:ea:d4:0e Processing RSN IE type 48, length 22 for mobile 2c:54:2d:ea:d4:0e
*apfMsConnTask_2: Dec 07 13:57:03.266: 2c:54:2d:ea:d4:0e CCKM: Mobile is using CCKM
*apfMsConnTask_2: Dec 07 13:57:03.266: 2c:54:2d:ea:d4:0e Received RSN IE with 0 PMKIDs from mobile 2c:54:2d:ea:d4:0e
*apfMsConnTask_2: Dec 07 13:57:03.266: 2c:54:2d:ea:d4:0e Found an cache entry for BSSID 34:bd:c8:b3:d9:f0 in PMKID cache at index 0 of station 2c:54:2d:ea:d4:0e
*apfMsConnTask_2: Dec 07 13:57:03.266: 2c:54:2d:ea:d4:0e Removing BSSID 34:bd:c8:b3:d9:f0 from PMKID cache of station 2c:54:2d:ea:d4:0e
*apfMsConnTask_2: Dec 07 13:57:03.266: 2c:54:2d:ea:d4:0e Resetting MSCB PMK Cache Entry 0 for station 2c:54:2d:ea:d4:0e
*apfMsConnTask_2: Dec 07 13:57:03.266: 2c:54:2d:ea:d4:0e Setting active key cache index 0 ---> 8
*apfMsConnTask_2: Dec 07 13:57:03.266: 2c:54:2d:ea:d4:0e unsetting PmkIdValidatedByAp
*apfMsConnTask_2: Dec 07 13:57:03.266: 2c:54:2d:ea:d4:0e CCKM: Processing REASSOC REQ IE
*apfMsConnTask_2: Dec 07 13:57:03.266: 2c:54:2d:ea:d4:0e CCKM: using HMAC SHA1 to compute MIC
*apfMsConnTask_2: Dec 07 13:57:03.266: 2c:54:2d:ea:d4:0e CCKM: Received a valid REASSOC REQ IE
*apfMsConnTask_2: Dec 07 13:57:03.267: 2c:54:2d:ea:d4:0e CCKM: Initializing PMK cache entry with a new PTK
*apfMsConnTask_2: Dec 07 13:57:03.267: 2c:54:2d:ea:d4:0e Setting active key cache index 8 ---> 8
*apfMsConnTask_2: Dec 07 13:57:03.267: 2c:54:2d:ea:d4:0e Resetting MSCB PMK Cache Entry 0 for station 2c:54:2d:ea:d4:0e
*apfMsConnTask_2: Dec 07 13:57:03.267: 2c:54:2d:ea:d4:0e Setting active key cache index 8 ---> 8
*apfMsConnTask_2: Dec 07 13:57:03.267: 2c:54:2d:ea:d4:0e Setting active key cache index 8 ---> 0
*apfMsConnTask_2: Dec 07 13:57:03.267: 2c:54:2d:ea:d4:0e Creating a PKC PMKID Cache entry for station 2c:54:2d:ea:d4:0e (RSN 2) on BSSID 34:bd:c8:b3:d9:f0
*apfMsConnTask_2: Dec 07 13:57:03.267: 2c:54:2d:ea:d4:0e Setting active key cache index 0 ---> 8
*apfMsConnTask_2: Dec 07 13:57:03.267: 2c:54:2d:ea:d4:0e CCKM: using HMAC SHA1 to compute MIC
*apfMsConnTask_2: Dec 07 13:57:03.267: 2c:54:2d:ea:d4:0e Including CCKM Response IE (length 54) in Assoc Resp to mobile
*apfMsConnTask_2: Dec 07 13:57:03.267: 2c:54:2d:ea:d4:0e Sending Assoc Response to station on BSSID 34:bd:c8:b2:b1:10 (status 202) ApVapId 1 Slot 0
*apfMsConnTask_2: Dec 07 13:57:03.267: 2c:54:2d:ea:d4:0e Scheduling deletion of Mobile Station: (callerId: 22) in 3 seconds
*apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e Association received from mobile on AP 34:bd:c8:b3:d9:f0
*apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1697)
*apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1864)
*apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e Applying site-specific Local Bridging override for station 2c:54:2d:ea:d4:0e - vapId 3, site 'Floor_1', interface '144_v'
*apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e Applying Local Bridging Interface Policy for station 2c:54:2d:ea:d4:0e - vlan 144, interface id 12, interface '144_v'
*apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e Applying site-specific override for station 2c:54:2d:ea:d4:0e - vapId 3, site 'Floor_1', interface '144_v'
*apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1697)
*apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1864)
*apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e STA - rates (4): 130 132 139 150 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e STA - rates (12): 130 132 139 150 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e extSuppRates statusCode is 0 and gotExtSuppRatesElement is 1
*apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e Processing RSN IE type 48, length 22 for mobile 2c:54:2d:ea:d4:0e
*apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e CCKM: Mobile is using CCKM
*apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e Received RSN IE with 0 PMKIDs from mobile 2c:54:2d:ea:d4:0e
*apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e Setting active key cache index 8 ---> 8
*apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e unsetting PmkIdValidatedByAp
*apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e apfMsRunStateDec
*apfMsConnTask_3: Dec 07 13:57:04.926: 2c:54:2d:ea:d4:0e apfMs1xStateDec
*apfMsConnTask_3: Dec 07 13:57:04.926: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Change state to START (0) last state RUN (20) -
AIR-AP1142N-A-K9 configuration issue for guest ssid
I'm trying to get the guest ssid working. I was frustrated so saved my old config and wiped out everything on this AP. Now my bvi1 does not come online.
ap#sh ip int bri
Interface IP-Address OK? Method Status Protocol
BVI1 192.168.2.249 YES NVRAM down down
Dot11Radio0 unassigned YES NVRAM up up
Dot11Radio0.50 unassigned YES unset up up
Dot11Radio0.51 unassigned YES unset up up
Dot11Radio1 unassigned YES NVRAM administratively down down
GigabitEthernet0 unassigned YES NVRAM up up
GigabitEthernet0.50 unassigned YES unset up up
GigabitEthernet0.51 unassigned YES unset up up
ap#
ap#sh int bvi
*May 6 15:05:24.611: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 847a.8835.4f22 Associated KEY_MGMT[WPAv2 PSK]1
BVI1 is down, line protocol is down
Hardware is BVI, address is 003a.99eb.8d00 (bia b862.1fe9.9af0)
Internet address is 192.168.2.249/24
MTU 1500 bytes, BW 54000 Kbit, DLY 5000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
3 packets output, 180 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
ap#
I have a private vlan 50 and the public vlan 51. The private ssid seems to work and allow connectivity to the internet but I don't understand with the same configuration the Public ssid doesn't seem to work.
I get this output when trying to connect with my cell phone.
*May 6 15:00:37.288: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 847a.8835.4f22 Reason: Sending station has left the BSS
*May 6 15:00:38.432: %DOT11-6-ASSOC: Interface Dot11Radio0, Station TYLOR-NB 9c4e.3617.483c Reassociated KEY_MGMT[WPAv2 PSK]
*May 6 15:00:42.935: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 847a.8835.4f22 Associated KEY_MGMT[WPAv2 PSK]
*May 6 15:00:54.320: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 2c44.01c3.70a6 Associated KEY_MGMT[WPAv2 PSK]
*May 6 15:01:13.913: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 847a.8835.4f22 Reason: Sending station has left the BSS
*May 6 15:01:17.281: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 847a.8835.4f22 Associated KEY_MGMT[WPAv2 PSK]
*May 6 15:01:48.181: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 847a.8835.4f22 Reason: Sending station has left the BSS
*May 6 15:01:51.583: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 847a.8835.4f22 Associated KEY_MGMT[WPAv2 PSK]
*May 6 15:02:22.500: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 847a.8835.4f22 Reason: Sending station has left the BSS
*May 6 15:03:41.852: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 847a.8835.4f22 Associated KEY_MGMT[WPAv2 PSK]
SSID [PUBLIC] :
MAC Address IP address Device Name Parent State
847a.8835.4f22 0.0.0.0 ccx-client - self Assoc
ap#
ap#show run
Building configuration...
Current configuration : 2746 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname ap
enable secret 5 $1$4jEJ$ajpjBvSx3DUhxyvLADj.91
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
dot11 syslog
dot11 ssid PRIVATE
vlan 50
authentication open
authentication key-management wpa version 2
mbssid guest-mode
wpa-psk ascii 7 01150F035E050E0A2D
dot11 ssid PUBLIC
vlan 51
authentication open
authentication key-management wpa version 2
mbssid guest-mode
wpa-psk ascii 7 045D02010A2F444B05
username Admin privilege 15 password 7 0526071D3545175840
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 50 mode ciphers aes-ccm
encryption vlan 51 mode ciphers aes-ccm
encryption mode ciphers aes-ccm tkip
ssid PRIVATE
ssid PUBLIC
antenna gain 0
mbssid
station-role root
interface Dot11Radio0.50
encapsulation dot1Q 50 native
no ip route-cache
bridge-group 50
bridge-group 50 subscriber-loop-control
bridge-group 50 block-unknown-source
no bridge-group 50 source-learning
no bridge-group 50 unicast-flooding
bridge-group 50 spanning-disabled
interface Dot11Radio0.51
encapsulation dot1Q 51
no ip route-cache
bridge-group 51
bridge-group 51 subscriber-loop-control
bridge-group 51 block-unknown-source
no bridge-group 51 source-learning
no bridge-group 51 unicast-flooding
bridge-group 51 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
antenna gain 0
dfs band 3 block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
no keepalive
interface GigabitEthernet0.50
encapsulation dot1Q 50 native
no ip route-cache
bridge-group 50
no bridge-group 50 source-learning
bridge-group 50 spanning-disabled
interface GigabitEthernet0.51
encapsulation dot1Q 51
no ip route-cache
bridge-group 51
no bridge-group 51 source-learning
bridge-group 51 spanning-disabled
interface BVI1
ip address 192.168.2.249 255.255.255.0
no ip route-cache
ip default-gateway 192.168.2.1
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
line vty 0 4
end
switch config:
interface FastEthernet1/0/46
switchport trunk encapsulation dot1q
switchport trunk native vlan 50
switchport trunk allowed vlan 50,51
switchport mode trunkHi
I know the bridge-group have to be identical to the sub interface number and vlan number
This is true for all other vlans except for native vlan. For native vlan sub-interfaces bridge group number always should be 1. In your case, if vlan 50 is the native vlan (192.168.2.x/24 belong vlan) then configure bridge-group 1 under those .50 sub-interfaces. Then everything should work :)
It is ideal if you could put AP management (BVI IP) into separate vlan & two user groups put vlan 50 & 51. Here is a sample configuration where vlan 110 is Mgmt & vlan 12,13 for user vlans.
http://mrncciew.com/2012/10/24/multiple-ssid-config-on-autonomous-ap/
HTH
Rasika
**** Pls rate all useful responses **** -
Setting up Multiple SSID's & VLAN
I have a Cisco 1230 AP along with a Sonic Wall TZ 210 and a Linksys SFE 2010P switch. On my AP I have created 2 SSID's. and 2 VLAN's. The first SSID is being broadcasted and has WPA encryption on it for our Corporate USers. The Second SSID is a Guest SSID and too is being broadcasted. I can make a laptop connect to the 1st SSID, but for some reason the 2nd SSID nothing will connect to it. The first SSID is associated to VLAN1 and the 2nd SSID is associated to VLAN2. VLAN1 has WPA encryption on it. VLAN2 is setup as Open and no Encryption. Any ideas?
My next question is how to I configure traffic on this AP with the other equipment mentioned? On my sonicwall we have segmented port6 on it to be a different subnet from the corporate subnet. On the Linksys switch I have enable VLANS on port2 and port48 which are on VLAN2. All other ports are on VLAN1. The AP connects to Ports 2 on the linksys switch and port 48 connects to port 6 on the Sonic Wall. When a corporate user connects to SSID1 I want them to be able to connect to the Corporate subnet. When a guest connects to SSID2 I want them to connect to the segmented guest network to only have Internet Access.
Hope this makes sense!
Below is my config on the AP. I am really only familiar with the IOS web interface so if you can explain it using that I'd appreciate it.
AP_WLAN_Bakery
Home Exec Configure
------------------ show version ------------------
Cisco IOS Software, C1200 Software (C1200-K9W7-M), Version 12.3(8)JEB1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 20-Jul-07 20:51 by dchih
ROM: Bootstrap program is C1200 boot loader
BOOTLDR: C1200 Boot Loader (C1200-BOOT-M) Version 12.2(8)JA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
AP_WLAN_Bakery uptime is 1 hour, 40 minutes
System returned to ROM by reload
System restarted at 10:52:05 -0400 Fri Oct 15 2010
System image file is "flash:/c1200-k9w7-mx.123-8.JEB1/c1200-k9w7-mx.123-8.JEB1"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-AP1231G-A-K9 (PowerPC405GP) processor (revision B0) with 15138K/1236K bytes of memory.
Processor board ID FOC0849218B
PowerPC405GP CPU at 196Mhz, revision number 0x0145
Last reset from reload
1 FastEthernet interface
1 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:12:D9:8B:09:93
Part Number : 73-8704-08
PCA Assembly Number : 800-23211-09
PCA Revision Number : A0
PCB Serial Number : FOC0849218B
Top Assembly Part Number : 800-23304-08
Top Assembly Serial Number : FTX0902R2V1
Top Revision Number : A0
Product/Model Number : AIR-AP1231G-A-K9
Configuration register is 0xF
------------------ show running-config ------------------
Building configuration...
Current configuration : 2544 bytes
! Last configuration change at 12:07:29 -0400 Fri Oct 15 2010 by admin
! NVRAM config last updated at 12:07:29 -0400 Fri Oct 15 2010 by admin
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname AP_WLAN_Bakery
clock timezone -0500 -5
clock summer-time -0400 recurring
ip subnet-zero
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
dot11 vlan-name VLAN_Corporate vlan 1
dot11 vlan-name VLAN_Guest vlan 2
dot11 ssid WLAN_Corporate
vlan 1
authentication open
authentication key-management wpa
mbssid guest-mode
wpa-psk ascii 7 005740565C0C5C5F5C741F
dot11 ssid WLAN_HartKitGuest
vlan 2
authentication open
mbssid guest-mode
username admin privilege 15 password 7 <removed>
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers aes-ccm tkip
encryption vlan 1 mode ciphers aes-ccm tkip
ssid WLAN_Corporate
ssid WLAN_HartKitGuest
mbssid
speed basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
station-role root
no dot11 extension aironet
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio0.2
encapsulation dot1Q 2
no ip route-cache
bridge-group 2
bridge-group 2 subscriber-loop-control
bridge-group 2 block-unknown-source
no bridge-group 2 source-learning
no bridge-group 2 unicast-flooding
bridge-group 2 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
interface FastEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface FastEthernet0.2
encapsulation dot1Q 2
no ip route-cache
bridge-group 2
no bridge-group 2 source-learning
bridge-group 2 spanning-disabled
interface BVI1
ip address 192.168.2.240 255.255.255.0
no ip route-cache
ip default-gateway 192.168.2.1
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
line vty 0 4
sntp server 192.168.2.5
sntp broadcast client
end
------------------ show stacks ------------------
Minimum process stacks:
Free/Size Name
4572/5500 soap_flash init
10024/11000 DHCP Autoinstall
5160/5500 Autoinstall
11748/12000 Setup
10552/11000 BootP Resolver
5240/5500 dot11 platform init
8824/12000 Init
5088/5500 RADIUS INITCONFIG
2576/3000 Rom Random Update Process
5144/11000 HTTP CP
3084/5500 Soap Flash Save Variables
Interrupt level stacks:
Level Called Unused/Size Name
4 125707 8056/9000 dot11 radio interrupt
6 9783 8960/9000 NS16550 VECTOR
------------------ show interfaces ------------------
BVI1 is up, line protocol is up
Hardware is BVI, address is 0012.d98b.0993 (bia 0013.1973.8d50)
Internet address is 192.168.2.240/24
MTU 1500 bytes, BW 54000 Kbit, DLY 5000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
5 minute input rate 10000 bits/sec, 9 packets/sec
5 minute output rate 10000 bits/sec, 4 packets/sec
59436 packets input, 8310033 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
31826 packets output, 18823451 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
Dot11Radio0 is up, line protocol is up
Hardware is 802.11G Radio, address is 0013.1973.8d50 (bia 0013.1973.8d50)
MTU 1500 bytes, BW 54000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:15:20, output 00:15:20, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 47
Queueing strategy: fifo
Output queue: 0/30 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
16093 packets input, 1696312 bytes, 0 no buffer
Received 1913 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
8367 packets output, 2930004 bytes, 0 underruns
13 output errors, 0 collisions, 37 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
Dot11Radio0.1 is up, line protocol is up
Hardware is 802.11G Radio, address is 0013.1973.8d50 (bia 0013.1973.8d50)
MTU 1500 bytes, BW 54000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation 802.1Q Virtual LAN, Vlan ID 1.
ARP type: ARPA, ARP Timeout 04:00:00
Last clearing of "show interface" counters never
Dot11Radio0.2 is up, line protocol is up
Hardware is 802.11G Radio, address is 0013.1973.8d50 (bia 0013.1973.8d50)
MTU 1500 bytes, BW 54000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation 802.1Q Virtual LAN, Vlan ID 2.
ARP type: ARPA, ARP Timeout 04:00:00
Last clearing of "show interface" counters never
FastEthernet0 is up, line protocol is up
Hardware is PowerPC405GP Ethernet, address is 0012.d98b.0993 (bia 0012.d98b.0993)
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Full-duplex, 100Mb/s, MII
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/160/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 13000 bits/sec, 10 packets/sec
5 minute output rate 10000 bits/sec, 4 packets/sec
75878 packets input, 12726627 bytes
Received 43517 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog
0 input packets with dribble condition detected
38986 packets output, 19917202 bytes, 0 underruns
0 output errors, 0 collisions, 7 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
FastEthernet0.1 is up, line protocol is up
Hardware is PowerPC405GP Ethernet, address is 0012.d98b.0993 (bia 0012.d98b.0993)
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation 802.1Q Virtual LAN, Vlan ID 1.
ARP type: ARPA, ARP Timeout 04:00:00
Last clearing of "show interface" counters never
FastEthernet0.2 is up, line protocol is up
Hardware is PowerPC405GP Ethernet, address is 0012.d98b.0993 (bia 0012.d98b.0993)
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation 802.1Q Virtual LAN, Vlan ID 2.
ARP type: ARPA, ARP Timeout 04:00:00
Last clearing of "show interface" counters never
------------------ show controllers ------------------
interface Dot11Radio0
Radio AIR-MP31G, Base Address 0013.1973.8d50, BBlock version 0.00, Software version 6.11.1
Serial number: FOC0901D4S1
Number of supported simultaneous BSSID on Dot11Radio0: 8
Carrier Set: Americas (US )
Uniform Spreading Required: No
Current Frequency: 2412 MHz Channel 1
Allowed Frequencies: 2412(1) 2417(2) 2422(3) 2427(4) 2432(5) 2437(6) 2442(7) 2447(8) 2452(9) 2457(10) 2462(11)
Listen Frequencies: 2412(1) 2417(2) 2422(3) 2427(4) 2432(5) 2437(6) 2442(7) 2447(8) 2452(9) 2457(10) 2462(11) 2467(12) 2472(13) 2484(14)
Beacon Flags: 0; Beacons are enabled; Probes are enabled
Current CCK Power: 100 mW
Allowed CCK Power Levels: 1 5 10 20 30 50 100
Current OFDM Power: 30 mW
Allowed OFDM Power Levels: 1 5 10 20 30
Allowed Client Power Levels: 1 5 10 20 30 50 100
ERP settings: short slot time.
Neighbors in non-erp mode:
Current Rates: basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
Active Rates: basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
Allowed Rates: 1.0 2.0 5.5 6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
Best Range Rates: basic-1.0 2.0 5.5 6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
Best Throughput Rates: basic-1.0 basic-2.0 basic-5.5 basic-6.0 basic-9.0 basic-11.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
Default Rates: basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
Current Voice Rates: 5.5 6.0 11.0 12.0 24.0 [disabled until voice packet-discard enabled]
Default Voice Rates: 5.5 6.0 11.0 12.0 24.0
Channel / Max Power Table
1 O=15 D=20, 2 O=15 D=20, 3 O=15 D=20, 4 O=15 D=20, 5 O=15 D=20
6 O=15 D=20, 7 O=15 D=20, 8 O=15 D=20, 9 O=15 D=20, 10 O=15 D=20
11 O=15 D=20
Data Rate Sensitivity (rate, SNR dB, Contention dBm)
( 1.0, 1, -98) ( 2.0, 7, -94) ( 5.5, 9, -92) (11.0, 16, -86)
( 6.0, 7, -92) ( 9.0, 14, -87) (12.0, 12, -87) (18.0, 15, -84)
(24.0, 17, -82) (36.0, 24, -76) (48.0, 29, -73) (54.0, 33, -69)
Radio Management (RM) Configuration:
Regular AP RM Mode 1 Temp Setting Disabled
Temp Settings: AP Tx Power 0 AP Tx Channel 0 Client Tx Power 0
Rates:
Saved Settings: AP Tx Power 0 AP Tx Channel 1 Client Tx Power 0
Rates:
MCST RSCs: [0]0x0 [1]0x0 [2]0x0 [3]0x0 [4]0x0
TKIP Cum Stats: STA MIC-L-Errs MIC-R-Errs Replay C-Measure
0000.0000.0000 00000000 00000000 00000000 00000000
AES-CCMP Cum Stats: 00000000 replays discarded
QBSS Load: 0x0
Policing Stats:Rx downgardes 0, Tx downgrades 0
Configured Local Access Class Parameters
Back : cw-min 4 cw-max 10 fixed-slot 7 admission-control Off txop 0
Best : cw-min 4 cw-max 6 fixed-slot 3 admission-control Off txop 0
Video : cw-min 3 cw-max 4 fixed-slot 1 admission-control Off txop 3008
Voice : cw-min 2 cw-max 3 fixed-slot 1 admission-control Off txop 1504
Configured Cell Access Class Parameters
Back : cw-min 4 cw-max 10 fixed-slot 7 admission-control Off txop 0
Best : cw-min 4 cw-max 10 fixed-slot 3 admission-control Off txop 0
Video : cw-min 3 cw-max 4 fixed-slot 2 admission-control Off txop 3008
Voice : cw-min 2 cw-max 3 fixed-slot 2 admission-control Off txop 1504
Transmit queues: Active 0 In Progress 0
---- Active --- In-Progress --------------- Counts --------------
Cnt Quo Bas Max Cnt Quo Bas Sent Discard Fail Retry Multi
Uplink 0 0 0 0 0 0 0 0 0 0 0 0
Voice 0 0 0 0 0 0 0 55 0 0 1 1
Video 0 0 0 0 0 0 0 0 0 0 0 0
Best 0 3 70 3 0 3 24 7937 0 0 127 12
Mcast 0 0 0 0 0 0 0 329 0 0 0 0
Mcast 0 0 0 0 0 0 0 30 0 0 0 0
Back 0 0 0 0 0 0 0 329 0 0 0 0
BSSIDS Index Flags State Next Held Defer NonDefer Clients Tsf Dtim Txq
8D50 0 20 0 0 0 0 0 0 200 2 0
8D51 1 20 0 0 0 0 0 0 150 2 1
UP ClientQAged AcQAged PacketAged Drop Retry/Thresh Timeout CQMax
7 0 0 0 3/100 0/500 35 4
6 0 0 0 3/100 0/500 35 4
5 0 0 0 3/100 0/500 35 4
4 0 0 0 3/100 0/500 35 4
3 0 0 0 3/100 0/500 35 4
2 0 0 0 3/100 0/500 35 4
1 0 0 0 3/100 0/500 35 4
Driver TX blocks: in use 0, high 10, at reset 0, fail 0, reclaim 0
Clients: 8021x auth in prog 0 allowed 0
Vlan BSSID Clients PSP Pri Encr Key0 Key1 Key2 Key3 SSIDs
0 8D50 0 0 0 0 234 x128
1n 8D50 0 0 0 0 234 x128 WLAN_Corporate
2 8D51 1 0 0 0 0 WLAN_HartKitGuest
0 0 flags 3
1 1 flags 3
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
17 0 flags 0
18 0 flags 0
Registers: io E8000000 mem 80000000 aux A0000000
0000 FF50 0000 0000 0021 0000 0000 0000
0001 0000 0000 0000 0000 0000 0000 0000
0000 0000 0000 0000 0000 0000 0000 0000
0500 0007 0000 0000 0808 09E8 0000 0504
0000 0000 0000 0000 0424 0059 E2ED 2D9D
00000000 00000200 20000200 FFFFFFFF F7FFFFFF 00000000 00000000 00200000
FFFFFFE2 00000FFF 72ED14BD 4A040401 00000000 00000000 00008000 00008080
00000000 00000000 00000000 00000000 00008F78 000012DC 00000000 0000C0EA
Radio running: temp 0 C tx_power 100 bb_code 0x0
rssi_threshold 0x0 gain offset 0
Antenna: external , gain 20 (platform 0, domain class A)
PCI sys_id: 0xA506 subsys_id 0x5100 (0x5101)
Unicast ciphers 0x1 mcast ciphers 0x1
Rid Ring:
A0000970: 009C8000 20ED1EA0 * n
Rx Ring:
A0000950: 893E0002 20ED3478 v, 893E0002 20EDEE60 v
A0000960: 893E0002 20EE4B54 v, 893E0002 20EDB068 * v
Tx Ring:
A0000800: 06108000 20ECFCE4 n, 009A8000 20ECD764 n
A0000810: 00AE8000 20ECF064 n, 010C8000 20ECD124 n
A0000820: 010C8000 20ECCE04 n, 010C8000 20ECE0C4 n
A0000830: 010C8000 20ECED44 n, 00668000 20ECB174 n
A0000840: 006A8000 20ECCA64 n, 010C8000 20ECDDA4 n
A0000850: 010C8000 20ECF6A4 n, 01848000 20ECF9C4 n
A0000860: 022A8000 20ECCE04 n, 01848000 20ECF9C4 n
A0000870: 06158000 20ED113C n, 01848000 20ECE3E4 n
A0000880: 022A8000 20ECF064 * n, 01188000 20ECD124 n
A0000890: 05688000 20ED0A74 n, 057C8000 20ED03AC n
A00008A0: 010C8000 20ECED44 n, 010C8000 20ECDDA4 n
A00008B0: 010C8000 20ECF6A4 n, 010C8000 20ECF9C4 n
A00008C0: 00748000 20ECB054 n, 05FC8000 20ED1804 n
TxDn Ring:
A0000930: 802C0000 20ED26A0 v, 802C0000 20ED2778 v
A0000940: 802C0000 20ED2850 * v, 802C0000 20ED2928 v
Multicast counters:
Internal MC counts:
28 (28) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0)
Log Buffer:
PowerPC405GP Ethernet unit 0
PHY Hardware is Intel LXT971 rev. 2 (id_register: 0x13, 0x78E2)
rx_intr: 0 tx_intr: 0 mac_err_isr: 0 phy_link_isr:0
Current station address 0012.d98b.0993, default address 0012.d98b.0993
MAL register dump:
malcr 0x0007C082 0x180
malesr 0x00000000 0x181
malier 0x0000000F 0x182
maltxcasr 0x80000000 0x184
maltxcarr 0x80000000 0x185
maltxeobisr 0x00000000 0x186
maltxdeir 0x00000000 0x187
malrxcasr 0x80000000 0x190
malrxcarr 0x80000000 0x191
malrxeobisr 0x00000000 0x192
malrxdeir 0x00000000 0x193
maltxctp0r 0x00EE6120 0x1A0
malrxctp0r 0x00EE6020 0x1C0
malrcbs0 0x00000060 0x1E0
EMAC register dump:
emacmr0 0x18000000 0x00
emacmr1 0xA1788000 0x04
emactmr0 0x00000000 0x08
emactmr1 0x380F0000 0x0C
emacrmr 0x7D180000 0x10
emacisr 0x00000002 0x14
emacier 0x00000001 0x18
emaciah 0x00000012 0x1C
emacial 0xD98B0993 0x20
emacptr 0x0000FFFF 0x2C
emaclsah 0x00000040 0x50
emaclsal 0x2B637E9B 0x54
emacipgr 0x00000004 0x58
emacstacr 0x47808011 0x5C
emactrtr 0x18000000 0x60
emacrwmr 0x0F002000 0x64
emacoctx 0x0132EA47 0x68
emacocrx 0x00C72D8B 0x6C
UIC register dump:
uicsr 0x00001FA3 0xC0
uicer 0x803F0048 0xC2
uicmsr 0x00000000 0xC6
PHY register dump:
3100 782D 0013 78E2 01E1 41E1 0007 2001 0000 0000 0000 0000 0000 0000 0000 0000
0384 4780 0032 0000 0422 0000 0000 0000 0000 0000 08C8 0000 0000 0000 0000
RX ring with 16 entries at 0xEE6020, Buffer size 1528
Rxhead = 0xEE6048 (5), Rxp = 0xB67360 (5)
00 pak=0x0B6D644 buf=0x0EF2BDC status=9C00 pak_size=0
01 pak=0x0B6CCA8 buf=0x0EF17A8 status=9C00 pak_size=0
02 pak=0x0B68C98 buf=0x0EE90F8 status=9C00 pak_size=0
03 pak=0x0B6BCA4 buf=0x0EEF5FC status=9C00 pak_size=0
04 pak=0x0B6DFE0 buf=0x0EF4010 status=9C00 pak_size=0
05 pak=0x0B6CFDC buf=0x0EF1E64 status=9C00 pak_size=0
06 pak=0x0B6C640 buf=0x0EF0A30 status=9C00 pak_size=0
07 pak=0x0B682FC buf=0x0EE7CC4 status=9C00 pak_size=0
08 pak=0x0B6E648 buf=0x0EF4D88 status=9C00 pak_size=0
09 pak=0x0B6E97C buf=0x0EF5444 status=9C00 pak_size=0
10 pak=0x0B6ECB0 buf=0x0EF5B00 status=9C00 pak_size=0
11 pak=0x0B6ACA0 buf=0x0EED450 status=9C00 pak_size=0
12 pak=0x0B68630 buf=0x0EE8380 status=9C00 pak_size=0
13 pak=0x0B6D310 buf=0x0EF2520 status=9C00 pak_size=0
14 pak=0x0B6C974 buf=0x0EF10EC status=9C00 pak_size=0
15 pak=0x0B6B63C buf=0x0EEE884 status=DC00 pak_size=0
TX ring with 8 entries at 0xEE6120, tx_count = 0
tx_head = 0xEE6148 (5), head_txp = 0xB673BC (5)
tx_tail = 0xEE6148 (5), tail_txp = 0xB673BC (5)
00 pak=0x0000000 buf=0x0000000 status=1400 pak_size=0
01 pak=0x0000000 buf=0x0000000 status=1400 pak_size=0
02 pak=0x0000000 buf=0x0000000 status=1400 pak_size=0
03 pak=0x0000000 buf=0x0000000 status=1400 pak_size=0
04 pak=0x0000000 buf=0x0000000 status=1400 pak_size=0
05 pak=0x0000000 buf=0x0000000 status=1400 pak_size=0
06 pak=0x0000000 buf=0x0000000 status=1400 pak_size=0
07 pak=0x0000000 buf=0x0000000 status=5400 pak_size=0
0 missed datagrams, 0 overruns
0 transmitter underruns, 0 excessive collisions
0 single collisions, 0 multiple collisions
0 dma memory errors, 0 CRC errors
0 alignment errors, 0 runts, 0 giants
emac/mal specific errors:
0 rx in range, 0 rx out range
0 mal_rx_serr, 0 mal_tx_serr
0 mal_rx_de, 0 mal_tx_de
0 emac_int
0 mal_err_isr
0 SQE errors, 0 tx CRC errors
0 output queue fail
------------------ show data-corruption ------------------
No data inconsistency errors have been recorded.
------------------ show file systems ------------------
File Systems:
Size(b) Free(b) Type Flags Prefixes
* 7741440 2734080 flash rw flash:
- - opaque rw bs:
7741440 2734080 unknown rw zflash:
- - opaque rw archive:
- - opaque rw system:
32768 29138 nvram rw nvram:
- - network rw tftp:
- - opaque rw null:
- - opaque ro xmodem:
- - opaque ro ymodem:
- - network rw rcp:
- - network rw ftp:
- - network rw http:
- - network rw scp:
- - network rw https:
------------------ show flash: ------------------
Directory of flash:/
2 -rwx 1048 Oct 15 2010 12:07:29 -04:00 private-multiple-fs
5 drwx 512 Oct 15 2010 10:36:30 -04:00 c1200-k9w7-mx.123-8.JEB1
4 -rwx 716 Feb 28 2002 19:06:22 -05:00 env_vars
146 -rwx 2549 Oct 15 2010 12:07:29 -04:00 config.txt
148 -rwx 5 Oct 15 2010 12:07:29 -04:00 private-config
7741440 bytes total (2734080 bytes free)
------------------ dir nvram: ------------------
Directory of nvram:/
30 -rw- 2549 <no date> startup-config
31 ---- 5 <no date> private-config
1 -rw- 0 <no date> ifIndex-table
32768 bytes total (29138 bytes free)
------------------ show memory statistics ------------------
Head Total(b) Used(b) Free(b) Lowest(b) Largest(b)
Processor A4AB84 4709500 2431436 2278064 1920552 2125904
I/O ECB000 1265664 468008 797656 727168 779580
------------------ show process memory ------------------
Total: 5975164, Used: 2899444, Free: 3075720
PID TTY Allocated Freed Holding Getbufs Retbufs Process
0 0 3373064 827724 1898920 0 0 *Init*
0 0 11804 7372856 11804 0 0 *Sched*
0 0 66125428 65999528 293168 434276 0 *Dead*
1 0 0 0 6416 0 0 Chunk Manager
2 0 188 188 3916 0 0 Load Meter
3 0 448120 443220 18392 0 0 HTTP CP
4 0 19548 0 25964 0 0 Check heaps
5 0 86364 207192 37368 49920 137052 Pool Manager
6 0 0 0 6416 0 0 AAA_SERVER_DEADT
7 0 188 188 6416 0 0 Timers
8 0 188 188 6416 0 0 AAA high-capacit
9 0 488 0 6904 0 0 SNTP
10 0 76 0 6492 0 0 ARP Input
11 0 3232 540 9108 0 0 Entity MIB API
12 0 0 0 6416 0 0 HC Counter Timer
13 0 188 188 6416 0 0 GraphIt
14 0 0 0 6416 0 0 Net Input
15 0 0 0 6416 0 0 Critical Bkgnd
16 0 19648 136 12180 0 0 Net Background
17 0 188 188 11916 0 0 Logger
18 0 188 188 6416 0 0 TTY Background
19 0 0 0 9916 0 0 Per-Second Jobs
20 0 188 188 6416 0 0 Compute load avg
21 0 0 0 6416 0 0 Per-minute Jobs
22 0 125880 59144 52956 0 0 Dot11 driver
23 0 188 188 6416 0 0 Dot11 driver log
24 0 0 0 6416 0 0 Voice Metrics Ta
25 0 0 0 6416 0 0 SOAP LED Process
26 0 188 188 6416 0 0 AAA Server
27 0 0 0 6416 0 0 AAA ACCT Proc
28 0 0 0 6416 0 0 ACCT Periodic Pr
29 0 2343100 10891400 16904 0 7173144 IP Input
30 0 0 0 6416 0 0 ICMP event handl
31 0 188 188 6416 0 0 AAA Dictionary R
32 0 47124 44272 9200 0 0 CDP Protocol
33 0 0 0 6416 0 0 linktest
34 0 964 964 9916 0 0 Dot11 aaa proces
35 0 0 0 9916 0 0 pmkid
36 0 188 6404 6416 0 0 Dot11 Mgmt & Ass
37 0 1636 1224 6644 0 0 AiroIAPP Protoco
38 0 188 188 6416 0 0 Triggered events
39 0 188 188 9916 0 0 Dot11 auth Dot1x
40 0 0 0 6416 0 0 Dot11 Mac Auth
41 0 1276 0 7692 0 0 Dot11CACprocess
42 0 0 1285716 11916 0 0 TCP Timer
43 0 0 0 11916 0 0 TCP Protocols
44 0 0 0 6416 0 0 Socket Timers
45 0 41144 11308 23364 0 0 DHCPD Receive
46 0 58666708 40499364 31400 6957504 101520 HTTP CORE
47 0 1072 188 12800 0 0 Soap Upgrade fet
48 0 10608 188 16836 0 0 DDP
49 0 344168 1754412 6416 0 0 LOCAL AAA
50 0 188 188 6416 0 0 AAA Cached Serve
51 0 188 188 6416 0 0 ENABLE AAA
52 0 188 188 6416 0 0 LINE AAA
54 0 2056 188 8284 0 0 TPLUS
55 0 604 188 9332 0 0 Crypto WUI
56 0 0 0 6416 0 0 EM Background Pr
57 0 188 308 6416 0 0 Soap Consoleless
58 0 72384 66968 14332 0 0 Crypto CA
59 0 0 0 8916 0 0 Crypto PKI-CRL
60 0 0 0 8916 0 0 Crypto SSL
61 0 2056 15044 6416 0 0 AAA SEND STOP EV
62 0 188 188 6416 0 0 Dot11 LBS Proc
63 0 0 0 6416 0 0 Syslog Traps
65 0 0 0 6416 0 0 DHCPD Timer
66 0 76 484 9992 0 0 DHCP Client
67 0 636960 188 22156 421308 0 HyBridge Input P
68 0 344 188 6588 0 0 Tbridge Monitor
69 0 344 188 6572 0 0 Spanning Tree
70 0 156 0 6628 0 0 DHCPD Database
2897284 Total
------------------ show process cpu ------------------
CPU utilization for five seconds: 16%/0%; one minute: 4%; five minutes: 1%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
1 0 1 0 0.00% 0.00% 0.00% 0 Chunk Manager
2 4 1196 3 0.00% 0.00% 0.00% 0 Load Meter
3 369 40 9225 0.00% 0.00% 0.00% 0 HTTP CP
4 764 611 1250 0.00% 0.00% 0.00% 0 Check heaps
5 9 44 204 0.00% 0.00% 0.00% 0 Pool Manager
6 0 1 0 0.00% 0.00% 0.00% 0 AAA_SERVER_DEADT
7 0 2 0 0.00% 0.00% 0.00% 0 Timers
8 0 9 0 0.00% 0.00% 0.00% 0 AAA high-capacit
9 8 158 50 0.00% 0.00% 0.00% 0 SNTP
10 1034 5268 196 0.00% 0.02% 0.00% 0 ARP Input
11 2 2 1000 0.00% 0.00% 0.00% 0 Entity MIB API
12 2 1494 1 0.00% 0.00% 0.00% 0 HC Counter Timer
13 2 5973 0 0.00% 0.00% 0.00% 0 GraphIt
14 0 11 0 0.00% 0.00% 0.00% 0 Net Input
15 0 1 0 0.00% 0.00% 0.00% 0 Critical Bkgnd
16 34 1906 17 0.00% 0.00% 0.00% 0 Net Background
17 4 101 39 0.00% 0.00% 0.00% 0 Logger
18 24 5969 4 0.00% 0.00% 0.00% 0 TTY Background
19 5 5998 0 0.00% 0.00% 0.00% 0 Per-Second Jobs
20 0 1196 0 0.00% 0.00% 0.00% 0 Compute load avg
21 433 127 3409 0.00% 0.00% 0.00% 0 Per-minute Jobs
22 587 181376 3 0.00% 0.00% 0.00% 0 Dot11 driver
23 0 2 0 0.00% 0.00% 0.00% 0 Dot11 driver log
24 2 1200 1 0.00% 0.00% 0.00% 0 Voice Metrics Ta
25 44 39944 1 0.00% 0.00% 0.00% 0 SOAP LED Process
26 238 3309 71 0.00% 0.00% 0.00% 0 AAA Server
27 0 1 0 0.00% 0.00% 0.00% 0 AAA ACCT Proc
28 0 1 0 0.00% 0.00% 0.00% 0 ACCT Periodic Pr
29 10607 39208 270 0.31% 0.16% 0.09% 0 IP Input
30 0 1 0 0.00% 0.00% 0.00% 0 ICMP event handl
31 0 2 0 0.00% 0.00% 0.00% 0 AAA Dictionary R
32 96 999 96 0.00% 0.00% 0.00% 0 CDP Protocol
33 2 5997 0 0.00% 0.00% 0.00% 0 linktest
34 14 115 121 0.00% 0.00% 0.00% 0 Dot11 aaa proces
35 1 100 10 0.00% 0.00% 0.00% 0 pmkid
36 116 2261 51 0.00% 0.00% 0.00% 0 Dot11 Mgmt & Ass
37 18 7228 2 0.00% 0.00% 0.00% 0 AiroIAPP Protoco
38 0 2 0 0.00% 0.00% 0.00% 0 Triggered events
39 0 2 0 0.00% 0.00% 0.00% 0 Dot11 auth Dot1x
40 0 1 0 0.00% 0.00% 0.00% 0 Dot11 Mac Auth
41 2 1200 1 0.00% 0.00% 0.00% 0 Dot11CACprocess
42 59 2009 29 0.00% 0.00% 0.00% 0 TCP Timer
43 0 1 0 0.00% 0.00% 0.00% 0 TCP Protocols
44 0 1 0 0.00% 0.00% 0.00% 0 Socket Timers
45 14 54 259 0.00% 0.00% 0.00% 0 DHCPD Receive
46 48468 30304 1599 9.35% 1.66% 0.36% 0 HTTP CORE
47 0 2 0 0.00% 0.00% 0.00% 0 Soap Upgrade fet
48 0 2 0 0.00% 0.00% 0.00% 0 DDP
49 707 3309 213 0.00% 0.02% 0.00% 0 LOCAL AAA
50 1 2 500 0.00% 0.00% 0.00% 0 AAA Cached Serve
51 0 2 0 0.00% 0.00% 0.00% 0 ENABLE AAA
52 0 2 0 0.00% 0.00% 0.00% 0 LINE AAA
54 0 2 0 0.00% 0.00% 0.00% 0 TPLUS
55 0 3 0 0.00% 0.00% 0.00% 0 Crypto WUI
56 0 1 0 0.00% 0.00% 0.00% 0 EM Background Pr
57 1 3 333 0.00% 0.00% 0.00% 0 Soap Consoleless
58 6 4 1500 0.00% 0.00% 0.00% 0 Crypto CA
59 0 1 0 0.00% 0.00% 0.00% 0 Crypto PKI-CRL
60 0 1 0 0.00% 0.00% 0.00% 0 Crypto SSL
61 3 16 187 0.00% 0.00% 0.00% 0 AAA SEND STOP EV
62 0 2 0 0.00% 0.00% 0.00% 0 Dot11 LBS Proc
63 0 1 0 0.00% 0.00% 0.00% 0 Syslog Traps
65 0 50 0 0.00% 0.00% 0.00% 0 DHCPD Timer
66 8 6027 1 0.00% 0.00% 0.00% 0 DHCP Client
67 8349 84826 98 0.55% 0.17% 0.10% 0 HyBridge Input P
68 14 6744 2 0.00% 0.00% 0.00% 0 Tbridge Monitor
69 0 2 0 0.00% 0.00% 0.00% 0 Spanning Tree
70 0 1690 0 0.00% 0.00% 0.00% 0 DHCPD Database
------------------ show process cpu history ------------------
AP_WLAN_Bakery 12:32:06 PM Friday Oct 15 2010 -0400
1133333
667777766666
100
90
80
70
60
50
40 *****
30 *****
20 *******
10 ************
0....5....1....1....2....2....3....3....4....4....5....5....
0 5 0 5 0 5 0 5 0 5
CPU% per second (last 60 seconds)
7 37 78 7 8
11 121961 87 1 3 1 1
100
90 *
80 ** *
70 * * ** * *
60 * * ** * *
50 * * ** * *
40 * ** ** * *
30 * ** ** * *
20 * ** #* * *
10 #*## ## # #
0....5....1....1....2....2....3....3....4....4....5....5....
0 5 0 5 0 5 0 5 0 5
CPU% per minute (last 60 minutes)
* = maximum CPU% # = average CPU%
8
8
100
90 *
80 *
70 *
60 *
50 *
40 *
30 *
20 *
10 *
0....5....1....1....2....2....3....3....4....4....5....5....6....6....7.
0 5 0 5 0 5 0 5 0 5 0 5 0
CPU% per hour (last 72 hours)
* = maximum CPU% # = average CPU%
------------------ show dot11 associations all-client ------------------
------------------ show wlccp ap mobility traffic ------------------
------------------ show wlccp ap mobility forwarding ------------------
------------------ show inventory ------------------
NAME: "AP1210", DESCR: "Cisco Aironet 1200 Series Access Point"
PID: ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ, VID: ÿÿÿ, SN: FTX0902R2V1
------------------ Mempool statistics ------------------
Head Total(b) Used(b) Free(b) Lowest(b) Largest(b)
Processor A4AB84 4709500 2431000 2278500 1920552 2125904
I/O ECB000 1265664 468008 797656 727168 779580
------------------ show memory summary -----------------
Processor memory
Alloc PC Size Blocks Bytes What
0x4790 0000000080 0000000001 0000000080 ACL Header
0x47A4 0000000024 0000000001 0000000024 Init
0x9FD4 0000000036 0000000001 0000000036 Init
0x9FFC 0000000040 0000000001 0000000040 Init
0xA018 0000000024 0000000001 0000000024 Init
0xA040 0000000036 0000000001 0000000036 Init
0xA134 0000000060 0000000001 0000000060 Init
0xF9D0 0000000024 0000000001 0000000024 HTTP CP
0xFAF8 0000000024 0000000001 0000000024 HTTP CP
0xFB6C 0000000076 0000000001 0000000076 HTTP CP
0xFC04 0000000024 0000000001 0000000024 HTTP CP
0xFC60 0000000028 0000000001 0000000028 HTTP CP
0xFD58 0000000024 0000000001 0000000024 Init
0xFDC4 0000000024 0000000001 0000000024 Init
0xFF2C 0000000036 0000000001 0000000036 HTTP CP
0xFF2C 0000000044 0000000001 0000000044 HTTP CP
0x11034 0000000024 0000000001 0000000024 Init
0x15750 0000004096 0000000001 0000004096 Init
0x1DD08 0000000120 0000000001 0000000120 Ion New Block
0x1F474 0000000024 0000000001 0000000024 LOGIN UNC PW
0x1F474 0000000056 0000000001 0000000056 LOGIN PWC (Free Blocks)
0x1F610 0000000080 0000000001 0000000080 local_aaa_authen2 (Free Blocks)
0x24F64 0000004784 0000000001 0000004784 (coalesced) (Free Blocks)
0x24F64 0000013956 0000000001 0000013956 (coalesced) (Free Blocks)
0x264F4 0000000512 0000000001 0000000512 Init
0x2CDF8 0000004312 0000000001 0000004312 TTY data
0x2E994 0000001500 0000000001 0000001500 String-DB entries
0x2E9BC 0000001500 0000000001 0000001500 String-DB owners
0x2E9E4 0000000776 0000000001 0000000776 String-DB handles
0x2E9FC 0000001024 0000000001 0000001024 String DB Hash Table
0x2F154 0000000024 0000000002 0000000048 SDB String
0x2F714 0000000176 0000000001 0000000176 SDB Owner info
0x2FF28 0000004312 0000000006 0000025872 TTY data
0x336E8 0000002000 0000000001 0000002000 TTY Input Buf
0x33720 0000000512 0000000001 0000000512 TTY Output Buf
0x3E6C0 0000000052 0000000003 0000000156 MAC ADDR subblock
0x40DA8 0000003000 0000000002 0000006000 keepalive sb chunk
0x42490 0000065536 0000000001 0000065536 Parseinfo Blocks
0x424B8 0000000364 0000000001 0000000364 tokenQ node
0x424E0 0000000432 0000000001 0000000432 Chain Cache Nodes
0x42508 0000032768 0000000001 0000032768 Parse Nodes
0x46E18 0000000120 0000000001 0000000120 Init
0x47028 0000000060 0000000001 0000000060 Init
0x47458 0000000024 0000000034 0000000816 Init
0x4755C 0000010000 0000000001 0000010000 Parser Linkage
0x47938 0000000056 0000000053 0000002968 Parser Mode
0x47938 0000000108 0000000001 0000000108 Parser Mode
0x479A4 0000000024 0000000054 0000001296 Parser Mode Q1
0x479C8 0000000024 0000000054 0000001296 Parser Mode Q2
0x49FA8 0000000432 0000000001 0000000432 Chain Cache No
0x4A070 0000000432 0000000009 0000003888 Chain Cache No
0x4A070 0000000432 0000000001 0000000432 Chain Cache No (Free Blocks)
0x4A070 0000000548 0000000001 0000000548 (coalesced) (Free Blocks)
0x4A160 0000000432 0000000001 0000000432 Chain Cache No
0x4FCD4 0000000256 0000000001 0000000256 HTTP CP
0x548F4 0000000032 0000000016 0000000512 Parser Alias
0x54924 0000000024 0000000016 0000000384 Init
0x5C338 0000004616 0000000001 0000004616 (coalesced) (Free Blocks)
0x5D464 0000000024 0000000001 0000000024 HTTP CP
0x5D4E4 0000000024 0000000001 0000000024 HTTP CP
0x65394 0000000024 0000000008 0000000192 Cond Debug definition
0x698F0 0000000068 0000000003 0000000204 GraphIt Data
0x6990C 0000001316 0000000003 0000003948 Graphit Client
0x69920 0000000024 0000000002 0000000048 Init
0x69920 0000000032 0000000001 0000000032 Init
0x73254 0000000164 0000000002 0000000328 Init
0x73278 0000000164 0000000002 0000000328 Init
0x7329C 0000000164 0000000002 0000000328 Init
0x7B12C 0000000164 0000000001 0000000164 Init
0x7B150 0000000164 0000000001 0000000164 Init
0x7B174 0000000164 0000000001 0000000164 Init
0x83E48 0000000060 0000000001 0000000060 HTTP CP
0x842C0 0000000044 0000000001 0000000044 HTTP CP
0x86C40 0000032772 0000000001 0000032772 Init
0x8AD2C 0000000024 0000000002 0000000048 AAA Secrettype
0x8AD64 0000000024 0000000002 0000000048 AAA Secrettype encrypt
0x8ADD0 0000000024 0000000002 0000000048 AAA_Secrettype pw
0x8B254 0000000192 0000000002 0000000384 AAA SG HEAD
0x8B294 0000000024 0000000002 0000000048 AAA SG NAME
0x8BFA8 0000000060 0000000001 0000000060 AAA MI SG NAME
0x8D1AC 0000003200 0000000001 0000003200 AAA attr list handle IDs
0x8DBA8 0000001024 0000000001 0000001024 AAA attr list handle IDs
0x9AE18 0000004096 0000000001 0000004096 AAA Unique Id Hash Table
0x9AED8 0000065536 0000000001 0000065536 AAA DB Chunk
0x9EFE8 0000020000 0000000001 0000020000 AAA Acct DB chunk
0xA0EA0 0000016336 0000000001 0000016336 AAA Acct Rec chunk
0xAFBC4 0000002048 0000000001 0000002048 AAA SG ID table
0xAFE78 0000001024 0000000003 0000003072 AAA SG ID table
0xB3D68 0000000032 0000000001 0000000032 Init
0xB4388 0000000024 0000000001 0000000024 AAA nvgend sg elt
0xB4388 0000000052 0000000001 0000000052 AAA nvgend sg elt
0xB43C0 0000000132 0000000002 0000000264 AAA Public Server Group
0xB4400 0000000028 0000000002 0000000056 AAA Public Server Group wrapper
0xB4448 0000000024 0000000002 0000000048 AAA pub SG servers
0xB44CC 0000000024 0000000002 0000000048 AAA pub SG wrap name
0xB4510 0000000024 0000000002 0000000048 AAA pub SG name
0xBC014 0000000776 0000000275 0000213400 *Free Packet Header*
0xBC014 0000000788 0000000001 0000000788 *Free Packet Header*
0xBC014 0000000804 0000000001 0000000804 *Free Packet Header*
0xBC014 0000000828 0000000001 0000000828 *Free Packet Header*
0xBC014 0000001408 0000000001 0000001408 (coalesced) (Free Blocks)
0xBC014 0000008480 0000000001 0000008480 (coalesced) (Free Blocks)
0xBCA88 0000000776 0000000003 0000002328 *In-use Packet Header*
0xC1274 0000004000 0000000001 0000004000 Packet Elements
0xC3B00 0000000184 0000000001 0000000184 IRB/CRB rxtypes
0xC3EE4 0000004712 0000000005 0000023560 *Hardware IDB*
0xC3EFC 0000001400 0000000005 0000007000 *Software IDB*
0xC4440 0000000024 0000000003 0000000072 HTTP CP
0xC4440 0000000076 0000000001 0000000076 HTTP CP
0xC4494 0000000024 0000000003 0000000072 HTTP CP
0xC4494 0000000080 0000000001 0000000080 HTTP CP
0xC4580 0000000184 0000000004 0000000736 IRB/CRB rxtypes
0xC4948 0000000048 0000000001 0000000048 HTTP CP
0xC4948 0000000052 0000000001 0000000052 HTTP CP
0xC4CB8 0000001400 0000000004 0000005600 *Software IDB*
0xC5864 0000000024 0000000004 0000000096 Init
0xC58E0 0000000024 0000000004 0000000096 Init
0xC8118 0000000032 0000000004 0000000128 IP Input
0xED1F0 0000035292 0000000001 0000035292 IDB List Element Chunks
0xFF3C0 0000000024 0000000059 0000001416 Init
0xFF7C4 0000000104 0000000008 0000000832 Init
0xFF7D4 0000000024 0000000006 0000000144 Init
0xFF7D4 0000000076 0000000001 0000000076 Init
0xFF7D4 0000000080 0000000001 0000000080 Init
0xFF8F4 0000000024 0000000001 0000000024 Init
0xFF9A4 0000000024 0000000007 0000000168 Init
0x102F38 0000010000 0000000001 0000010000 AAA chunk
0x103140 0000004616 0000000001 0000004616 AAA Acct AVLnode chunk
0x107F7C 0000000100 0000000001 0000000100 AAA MLIST
0x1081E8 0000000092 0000000001 0000000092 AAA MLIST
0x108A7C 0000001024 0000000002 0000002048 AAA mlist ID table
0x118430 0000001500 0000000007 0000010500 List Elements
0x119688 0000001500 0000000001 0000001500 List Elements
0x1196C8 0000005000 0000000001 0000005000 List Headers
0x11D7D4 0000001032 0000000001 0000001032 Process Array
0x11F5B0 0000000640 0000000068 0000043520 Process
0x11F5B0 0000000856 0000000001 0000000856 (coalesced) (Free Blocks)
0x1213A8 0000001500 0000000001 0000001500 Watched Semaph
0x1219A4 0000000144 0000000064 0000009216 Process Events
0x1219A4 0000000160 0000000002 0000000320 Process Events
0x1219A4 0000000172 0000000001 0000000172 Process Events
0x1219A4 0000000200 0000000001 0000000200 Process Events
0x1219A4 0000000208 0000000001 0000000208 Process Events
0x1219A4 0000000256 0000000001 0000000256 (coalesced) (Free Blocks)
0x1219A4 0000000432 0000000001 0000000432 (coalesced) (Free Blocks)
0x1219A4 0000000556 0000000001 0000000556 (coalesced) (Free Blocks)
0x123C24 0000001500 0000000001 0000001500 messages
0x123C50 0000001500 0000000001 0000001500 Watched messages
0x123C7C 0000010000 0000000001 0000010000 Watched Queue
0x123CA4 0000005000 0000000001 0000005000 Watched Boolean
0x123CCC 0000005000 0000000001 0000005000 Watched Bitfield
0x123CF4 0000001500 0000000001 0000001500 Watched Semaphore
0x123D18 0000005000 0000000001 0000005000 Watcher Info
0x123D40 0000000500 0000000001 0000000500 Watched Message Queue
0x123D68 0000001500 0000000001 0000001500 Watcher Message Queue
0x123D90 0000003000 0000000001 0000003000 Read/Write Locks
0x126050 0000002000 0000000001 0000002000 Reg Function 12
0x126078 0000001500 0000000001 0000001500 Reg Function iList
0x1260A0 0000001500 0000000001 0000001500 Reg Function Caselist
0x126118 0000002000 0000000005 0000010000 Reg Function 1
0x12657C 0000002000 0000000001 0000002000 Reg Function 1
0x129F50 0000000024 0000000002 0000000048 *Sched*
0x129F50 0000000032 0000000001 0000000032 *Sched*
0x129F50 0000000044 0000000008 0000000352 *Sched*
0x12A228 0000000256 0000000001 0000000256 Init
0x12C5F8 0000003000 0000000001 0000003000 CCA CCB chunks
0x12CDBC 0000000048 0000000008 0000000384 CCA Component
0x12CE24 0000000024 0000000007 0000000168 CCA Notification Flags
0x12CE24 0000000048 0000000001 0000000048 CCA Notification Flags
0x12CE84 0000003000 0000000008 0000024000 Keepalive
0x12CFF4 0000000024 0000000003 0000000072 CCA UserType
0x12D0A8 0000003000 0000000001 0000003000 CCA CLA chunks
0x1301C0 0000000024 0000000001 0000000024 TW Wheels
0x130200 0000016384 0000000003 0000049152 TW Buckets
0x13AA18 0000000112 0000000006 0000000672 Process Signals
0x13B01C 0000003000 0000000001 0000003000 Process Stack
0x13B01C 0000005500 0000000049 0000269500 Process Stack
0x13B01C 0000008000 0000000004 0000032000 Process Stack
0x13B01C 0000009000 0000000006 0000054000 Process Stack
0x13B01C 0000011000 0000000009 0000099000 Scheduler Stack
0x13B01C 0000018000 0000000001 0000018000 Interrupt Stack
0x13B01C 0002125900 0000000001 0002125900 (coalesced) (Free Blocks)
0x14F6BC 0000020000 0000000001 0000020000 Managed Chunk Queue Elements
0x151870 0000000068 0000000001 0000000068 (fragment) (Free Blocks)
0x1559A8 0000000296 0000000008 0000002368 Pool Info
0x155F84 0000000032 0000000001 0000000032 Pool Cache
0x15AF2C 0000000264 0000000001 0000000264 CLASSMAP_MODULE
0x15B7B0 0000000104 0000000001 0000000104 CLASSMAP_MODULE
0x15B8D0 0000000136 0000000001 0000000136 CLASSMAP_MODULE
0x15B8F0 0000000024 0000000001 0000000024 CLASSMAP_MODULE
0x15BA20 0000000024 0000000001 0000000024 CLASSMAP_MODULE
0x1826A8 0000000256 0000000001 0000000256 Init
0x182B78 0000000256 0000000001 0000000256 Init
0x1875C0 0000000776 0000000002 0000001552 *In-use Packet Header*
0x188DF4 0000000288 0000000003 0000000864 SNTP
0x188DF4 0000000332 0000000001 0000000332 DDP
0x1904D0 0000000776 0000000001 0000000776 *In-use Packet Header*
0x193CB8 0000001184 0000000005 0000005920 TCP CB
0x193CB8 0000000728 0000000001 0000000728 (fragment) (Free Blocks)
0x1A86AC 0000003000 0000000001 0000003000 IP Addresses
0x1AE490 0000000024 0000000004 0000000096 HTTP CP
0x1AE490 0000000032 0000000001 0000000032 Dot11 driver
0x1AE490 0000000048 0000000001 0000000048 AiroIAPP Protocol
0x1AE490 0000000068 0000000001 0000000068 HTTP CP
0x1CDDA0 0000000280 0000000004 0000001120 Init
0x1CDDAC 0000000068 0000000004 0000000272 Init
0x1EB928 0000005000 0000000001 0000005000 ip localpool
0x1EFFC4 0000000024 0000000001 0000000024 Init
0x1F9E40 0000001652 0000000003 0000004956 HTTP CORE
0x1F9EC8 0000000128 0000000003 0000000384 DHCPD Receive
0x1FBF20 0000000172 0000000002 0000000344 DHCPD Receive
0x1FBF20 0000000232 0000000001 0000000232 HTTP CORE
0x1FBF20 0000000500 0000000001 0000000500 (coalesced) (Free Blocks)
0x1FF2DC 0000000040 0000000001 0000000040 DHCPD Receive
0x206B78 0000000024 0000000003 0000000072 Init
0x206BA8 0000000024 0000000003 0000000072 Init
0x20BE88 0000001500 0000000001 0000001500 Syslogd Messages chunk
0x20FEF0 0000000024 0000000001 0000000024 Init
0x221B18 0000010000 0000000001 0000010000 Time Range Entry Chunks
0x221B40 0000003000 0000000001 0000003000 Time Range Item Chunks
0x221B68 0000001500 0000000001 0000001500 Time Range User Chunks
0x2221E4 0000000036 0000000016 0000000576 Init
0x222214 0000000040 0000000016 0000000640 Init
0x2233CCHi,
if you remove "encryption mode ciphers aes-ccm tkip" from the radio interface does it help?
it should remain like this:
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 1 mode ciphers aes-ccm tkip
ssid WLAN_Corporate
ssid WLAN_HartKitGuest
HTH,
Tiago
If this helps you and/or answers your question please mark the question as "answered" and/or rate it, so other users can easily find it. -
How do i update my SSiD on an officejet pro 8600e?
Hi! I just got a new router and now my printer isn't connecting to my computer. I would think I need to update the SSID to match the one on my new router so I can print again. How do I do this?
Thanks!
This question was solved.
View Solution.Replacing your wireless router try here.
http://www.hp.com/global/au/en/wireless/reconfiguring-system-help3.html
Say thanks by clicking the Kudos Thumbs Up to the right in the post.
If my post resolved your problem, please mark it as an Accepted Solution ...
I worked for HP but now I'm retired! -
I have a Problem with Romming Between SSIDs withing the same WLC but with deferent VLAN .
HI All,
I have a Problem with Romming Between SSIDs withing the same WLC but with deferent VLAN . the WLC are providing the HQ and one of the Branches the Wireless services .
Am using all the available 9 SSIDs at the HQ , and am using only 4 of it at the Brnche.
The problem that i have are happening only at the Branch office as i cant room between the SSIDs within Diferent VLANs but i can do it with the one that pointing to the same VLAN. Once the client ( Laptop/Phone ) connected to one of the SSIDs. it imposiible to have him connected to the other ones with Different VLAN. meanwhile, It says its connected to the other SSID but its not getting IP from that pool.
here is the Show Run-Config from my WLC .. and the Problem happening between the SSID AMOBILE and ASTAFF. i have the Debug while am switching between the SSIDs if needed .
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.11.04 10:20:47 =~=~=~=~=~=~=~=~=~=~=~=
show run-config
Press Enter to continue...
System Inventory
NAME: "Chassis" , DESCR: "Cisco 5500 Series Wireless LAN Controller"
PID: AIR-CT5508-K9, VID: V01, SN: FCW1535L01G
Burned-in MAC Address............................ 30:E4:DB:1B:99:80
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 12
Press Enter to continue or <ctrl-z> to abort
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.0.235.0
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console 1.27
Build Type....................................... DATA + WPS
System Name...................................... WLAN Controller 5508
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
IP Address....................................... 10.125.18.15
Last Reset....................................... Software reset
System Up Time................................... 41 days 5 hrs 14 mins 42 secs
System Timezone Location......................... (GMT -5:00) Eastern Time (US and Canada)
Current Boot License Level....................... base
Current Boot License Type........................ Permanent
Next Boot License Level.......................... base
Next Boot License Type........................... Permanent
Configured Country............................... US - United States
--More or (q)uit current module or <ctrl-z> to abort
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +36 C
External Temperature............................. +20 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 10
Number of Active Clients......................... 61
Burned-in MAC Address............................ 30:E4:DB:1B:99:80
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 12
Press Enter to continue or <ctrl-z> to abort
AP Bundle Information
Primary AP Image Size
ap3g1 5804
ap801 5192
ap802 5232
c1100 3096
c1130 4972
c1140 4992
c1200 3364
c1240 4812
c1250 5512
c1310 3136
c1520 6412
c3201 4324
c602i 3716
Secondary AP Image Size
ap801 4964
c1100 3036
--More or (q)uit current module or <ctrl-z> to abort
c1130 4884
c1140 4492
c1200 3316
c1240 4712
c1250 5064
c1310 3084
c1520 5244
c3201 4264
Press Enter to continue or <ctrl-z> to abort
Switch Configuration
802.3x Flow Control Mode......................... Disable
FIPS prerequisite features....................... Disabled
secret obfuscation............................... Enabled
Strong Password Check Features:
case-check ...........Enabled
consecutive-check ....Enabled
default-check .......Enabled
username-check ......Enabled
Press Enter to continue or <ctrl-z> to abort
Network Information
RF-Network Name............................. OGR
Web Mode.................................... Disable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Enable
OCSP........................................ Disabled
OCSP responder URL..........................
Secure Shell (ssh).......................... Enable
Telnet...................................... Disable
Ethernet Multicast Forwarding............... Disable
Ethernet Broadcast Forwarding............... Disable
AP Multicast/Broadcast Mode................. Unicast
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
IGMP Query Interval......................... 20 seconds
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
Cisco AP Default Master..................... Enabled
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Disable
Mgmt Via Dynamic Interface.................. Disable
--More or (q)uit current module or <ctrl-z> to abort
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
AP Fallback ................................ Enable
Web Auth Redirect Ports .................... 80
Web Auth Proxy Redirect ................... Disable
Fast SSID Change ........................... Enabled
AP Discovery - NAT IP Only ................. Enabled
IP/MAC Addr Binding Check .................. Enabled
Press Enter to continue or <ctrl-z> to abort
Port Summary
STP Admin Physical Physical Link Link
Pr Type Stat Mode Mode Status Status Trap POE SFPType
1 Normal Forw Enable Auto 1000 Full Up Enable N/A 1000BaseTX
2 Normal Disa Enable Auto Auto Down Enable N/A Not Present
3 Normal Disa Enable Auto Auto Down Enable N/A Not Present
4 Normal Disa Enable Auto Auto Down Enable N/A Not Present
5 Normal Disa Enable Auto Auto Down Enable N/A Not Present
6 Normal Disa Enable Auto Auto Down Enable N/A Not Present
7 Normal Disa Enable Auto Auto Down Enable N/A Not Present
8 Normal Disa Enable Auto Auto Down Enable N/A Not Present
Press Enter to continue or <ctrl-z> to abort
AP Summary
Number of APs.................................... 8
Global AP User Name.............................. Not Configured
Global AP Dot1x User Name........................ Not Configured
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
KNOWLOGY_DC01 2 AIR-LAP1131AG-A-K9 00:1d:45:86:ed:4e KNOWLOGY_DC_Serv 1 US 1
KNOWLOGY_DC02 2 AIR-LAP1131AG-A-K9 00:21:d8:36:c5:c4 KNOWLOGY_DC_Serv 1 US 1
KN1252_AP01 2 AIR-LAP1252AG-A-K9 00:21:d8:ef:06:50 Knowlogy Confere 1 US 1
KN1252_AP02 2 AIR-LAP1252AG-A-K9 00:22:55:8e:2e:d4 Server Room Side 1 US 1
Anham_AP03 2 AIR-LAP1142N-A-K9 70:81:05:88:15:b5 default location 1 US 1
ANHAM_AP01 2 AIR-LAP1142N-A-K9 70:81:05:b0:e4:62 Small Conference 1 US 1
ANHAM_AP04 2 AIR-LAP1131AG-A-K9 00:1d:45:86:e1:b8 Conference room 1 US 1
ANHAM_AP02 2 AIR-LAP1142N-A-K9 70:81:05:96:7a:49 Copy Room 1 US 1
AP Tcp-Mss-Adjust Info
AP Name TCP State MSS Size
KNOWLOGY_DC01 disabled -
KNOWLOGY_DC02 disabled -
--More or (q)uit current module or <ctrl-z> to abort
KN1252_AP01 disabled -
KN1252_AP02 disabled -
Anham_AP03 disabled -
ANHAM_AP01 disabled -
ANHAM_AP04 disabled -
ANHAM_AP02 disabled -
Press Enter to continue or <ctrl-z> to abort
AP Location
Total Number of AP Groups........................ 3
Site Name........................................ ANHAM8075
Site Description................................. ANHAM 8075 Location
WLAN ID Interface Network Admission Control Radio Policy
1 knowlogy_ogr Disabled None
6 knowlogy_ogr Disabled None
9 knowlogy_ogr Disabled None
7 knowlogy_ogr Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
Anham_AP03 2 AIR-LAP1142N-A-K9 70:81:05:88:15:b5 default location 1 US 1
ANHAM_AP01 2 AIR-LAP1142N-A-K9 70:81:05:b0:e4:62 Small Conference 1 US 1
ANHAM_AP04 2 AIR-LAP1131AG-A-K9 00:1d:45:86:e1:b8 Conference room 1 US 1
ANHAM_AP02 2 AIR-LAP1142N-A-K9 70:81:05:96:7a:49 Copy Room 1 US 1
Site Name........................................ Knowlogy_DC
--More or (q)uit current module or <ctrl-z> to abort
Site Description................................. DC Center Access points
WLAN ID Interface Network Admission Control Radio Policy
2 knowlogy_ogr Disabled None
4 knowlogy_ogr Disabled None
3 knowlogy_ogr Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
KNOWLOGY_DC01 2 AIR-LAP1131AG-A-K9 00:1d:45:86:ed:4e KNOWLOGY_DC_Serv 1 US 1
KNOWLOGY_DC02 2 AIR-LAP1131AG-A-K9 00:21:d8:36:c5:c4 KNOWLOGY_DC_Serv 1 US 1
Site Name........................................ OGR
Site Description................................. 1934 OGR Office
WLAN ID Interface Network Admission Control Radio Policy
1 knowlogy_ogr Disabled None
2 knowlogy_ogr Disabled None
4 knowlogy_ogr Disabled None
6 knowlogy_ogr Disabled None
--More or (q)uit current module or <ctrl-z> to abort
7 knowlogy_ogr Disabled None
9 knowlogy_ogr Disabled None
8 knowlogy_ogr Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
KN1252_AP01 2 AIR-LAP1252AG-A-K9 00:21:d8:ef:06:50 Knowlogy Confere 1 US 1
KN1252_AP02 2 AIR-LAP1252AG-A-K9 00:22:55:8e:2e:d4 Server Room Side 1 US 1
Site Name........................................ default-group
Site Description................................. <none>
WLAN ID Interface Network Admission Control Radio Policy
1 knowlogy_ogr Disabled None
2 knowlogy_ogr Disabled None
3 knowlogy_ogr Disabled None
4 knowlogy_ogr Disabled None
5 knowlogy_ogr Disabled None
6 knowlogy_ogr Disabled None
7 knowlogy_ogr Disabled None
8 knowlogy_ogr Disabled None
--More or (q)uit current module or <ctrl-z> to abort
9 knowlogy_ogr Disabled None
10 management Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
Press Enter to continue or <ctrl-z> to abort
AP Config
Cisco AP Identifier.............................. 6
Cisco AP Name.................................... KNOWLOGY_DC01
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:86:ed:4e
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.100
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................ wireless.knowlogy.com
Primary Cisco Switch IP Address.................. 10.125.18.15
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
--More or (q)uit current module or <ctrl-z> to abortIP Address.................. 10.125.18.15
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
--More or (q)uit current module or <ctrl-z> to abort
Reset Button..................................... Enabled
AP Serial Number................................. FTX1134T0QG
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 48 days, 20 h 19 m 18 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:33 2013
Join Taken Time.................................. 0 days, 00 h 10 m 47 s
--More or (q)uit current module or <ctrl-z> to abort
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211b
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:71:09:8f:90
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
--More or (q)uit current module or <ctrl-z> to abort
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
--More or (q)uit current module or <ctrl-z> to abort
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy DSSS parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 11
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11
Current CCA Mode .......................... 0
ED Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
--More or (q)uit current module or <ctrl-z> to abort
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Cisco AP Identifier.............................. 6
Cisco AP Name.................................... KNOWLOGY_DC01
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:86:ed:4e
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.100
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
--More or (q)uit current module or <ctrl-z> to abort
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................ wireless.knowlogy.com
Primary Cisco Switch Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
--More or (q)uit current module or <ctrl-z> to abort
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
Reset Button..................................... Enabled
AP Serial Number................................. FTX1134T0QG
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
--More or (q)uit current module or <ctrl-z> to abort
AP Up Time....................................... 48 days, 20 h 19 m 18 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:33 2013
Join Taken Time.................................. 0 days, 00 h 10 m 47 s
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Radio Subband................................ RADIO_SUBBAND_ALL
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:71:09:8f:90
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
--More or (q)uit current module or <ctrl-z> to abort
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... MANDATORY
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 20
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
--More or (q)uit current module or <ctrl-z> to abort
Tx Power
Num Of Supported Power Levels ............. 7
Tx Power Level 1 .......................... 15 dBm
Tx Power Level 2 .......................... 14 dBm
Tx Power Level 3 .......................... 11 dBm
Tx Power Level 4 .......................... 8 dBm
Tx Power Level 5 .......................... 5 dBm
Tx Power Level 6 .......................... 2 dBm
Tx Power Level 7 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 44
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
......................................... 104,108,112,116,132,136,140,
......................................... 149,153,157,161
TI Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
--More or (q)uit current module or <ctrl-z> to abort
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Press Enter to continue or <ctrl-z> to abort
Cisco AP Identifier.............................. 3
Cisco AP Name.................................... KNOWLOGY_DC02
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:21:d8:36:c5:c4
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.101
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
--More or (q)uit current module or <ctrl-z> to abort
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Enabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
Reset Button..................................... Enabled
--More or (q)uit current module or <ctrl-z> to abort
AP Serial Number................................. FTX1230T24F
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 48 days, 20 h 24 m 41 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:35 2013
Join Taken Time.................................. 0 days, 00 h 10 m 48 s
--More or (q)uit current module or <ctrl-z> to abort
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211b
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:22:55:a5:0c:30
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
--More or (q)uit current module or <ctrl-z> to abort
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
--More or (q)uit current module or <ctrl-z> to abort
Current Tx Power Level .................... 1
Phy DSSS parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 1
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11
Current CCA Mode .......................... 0
ED Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
--More or (q)uit current module or <ctrl-z> to abort
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Cisco AP Identifier.............................. 3
Cisco AP Name.................................... KNOWLOGY_DC02
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:21:d8:36:c5:c4
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.101
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
--More or (q)uit current module or <ctrl-z> to abort
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Enabled
PoE Power Injector MAC Addr...................... Disabled
--More or (q)uit current module or <ctrl-z> to abort
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
Reset Button..................................... Enabled
AP Serial Number................................. FTX1230T24F
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
--More or (q)uit current module or <ctrl-z> to abort
AP Up Time....................................... 48 days, 20 h 24 m 41 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:35 2013
Join Taken Time.................................. 0 days, 00 h 10 m 48 s
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Radio Subband................................ RADIO_SUBBAND_ALL
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:22:55:a5:0c:30
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
--More or (q)uit current module or <ctrl-z> to abort
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... MANDATORY
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 20
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
--More or (q)uit current module or <ctrl-z> to abort
Tx Power
Num Of Supported Power Levels ............. 7
Tx Power Level 1 .......................... 15 dBm
Tx Power Level 2 .......................... 14 dBm
Tx Power Level 3 .......................... 11 dBm
Tx Power Level 4 .......................... 8 dBm
Tx Power Level 5 .......................... 5 dBm
Tx Power Level 6 .......................... 2 dBm
Tx Power Level 7 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 36
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
......................................... 104,108,112,116,132,136,140,
......................................... 149,153,157,161
TI Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
--More or (q)uit current module or <ctrl-z> to abort
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Press Enter to continue or <ctrl-z> to abort
Cisco AP Identifier.............................. 5
Cisco AP Name.................................... KN1252_AP01
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:21:d8:ef:06:50
IP Address Configuration......................... DHCP
IP Address....................................... 10.125.18.101
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 10.125.18.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Enabled
Ssh State........................................ Disabled
Cisco AP Location................................ Knowlogy Conference Rooms Side
Cisco AP Group Name.............................. OGR
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
--More or (q)uit current module or <ctrl-z> to abort
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.4.10.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. PoE/Medium Power (15.4 W)
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1252AG-A-K9
AP Image......................................... C1250-K9W8-M
IOS Version...................................... 12.4(23c)JA5
--More or (q)uit current module or <ctrl-z> to abort
Reset Button..................................... Enabled
AP Serial Number................................. FTX122990L5
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 118
WLAN 1 :........................................ 111
WLAN 2 :........................................ 111
WLAN 4 :........................................ 112
WLAN 6 :........................................ 112
WLAN 7 :........................................ 111
WLAN 9 :........................................ 112
WLAN 8 :........................................ 112
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 26 days, 00 h 24 m 39 s
--More or (q)uit current module or <ctrl-z> to abort
AP LWAPP Up Time................................. 26 days, 00 h 23 m 48 s
Join Date and Time............................... Wed Oct 9 10:59:07 2013
Join Taken Time.................................. 0 days, 00 h 00 m 50 s
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211n-2.4
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 7
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:22:55:df:a5:90
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
--More or (q)uit current module or <ctrl-z> to abort
11000 Kilo Bits.......................... MANDATORY
MCS Set
MCS 0.................................... SUPPORTED
MCS 1.................................... SUPPORTED
MCS 2.................................... SUPPORTED
MCS 3.................................... SUPPORTED
MCS 4.................................... SUPPORTED
MCS 5.................................... SUPPORTED
MCS 6.................................... SUPPORTED
MCS 7.................................... SUPPORTED
MCS 8.................................... SUPPORTED
MCS 9.................................... SUPPORTED
MCS 10................................... SUPPORTED
MCS 11................................... SUPPORTED
MCS 12................................... SUPPORTED
MCS 13................................... SUPPORTED
MCS 14................................... SUPPORTED
MCS 15................................... SUPPORTED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
--More or (q)uit current module or <ctrl-z> to abort
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 ..........Well you need to understand the behavior of h-reap or what it's called now, FlexConnect. In this mode, the clients are still remembers on the WLC until the session timer/idle timer expires. So switching between SSID's in h-reap will not be the same when switching when the AP's are in local mode.
Take a look at the client when connected in FlexConnect in the WLC GUI monitor tab. Thus will show you what ssid and vlan the client is on. Now switch to a different ssid and compare this. It's probably the same because the client has not timed out. Now go back to the other ssid and look again. Now on the WLC, remove or delete the client and then switch to the other ssid at the same time. Or switch SSID's and then remove the client. The client will join the new ssid and in the monitor tab, you should see the info.
There is no need to have clients have multiple SSID's unless your testing. Devices should only have one ssid profile configured to eliminate any connectivity issues from the device wanting to switch SSID's.
Sent from Cisco Technical Support iPhone App -
How to find SSID and Network Key to setup wireless printer to iMac?
It is easy to find your "SSID" and "Network Key" once you understand what you are looking for. Here is what worked for me when I setup a new wirless printer today:
1) SSID = Your Network Name
Ex. Jason's Wi-Fi Network
Ex. Harry's Lounge
First way to find: on an iMac, go to the top bar on the right side and click on the "wireless symbol". You will see a list of all the wireless networks your computer is picking up. The one you are connected to (if you are able to surf the Internet) is the name you enter when asked for the SSID.
NOVICE HINT: This is the equivalent to walking into a Starbucks and logging onto their wi-fi via their "network name," which has the word Starbucks in it. Some network names will have have locks next to them, meaning they are "secured by a password" and some will not, meaning anyone can access this "free" wi-fi. This doesn't matter either way, it just helps with making sure you have located the list. Of course, it is also possible, if you live in a remote area, that only your network name will show up.
Second way to find: on an iMac, go to the apple symbol in the upper left corner of computer and make sure it says "finder" (if it doesn't, just click on your desktop and it will show up), then select:
go > applications > utilities > Airport Utility > double-click on the image of the AirPort Extreme and the network name will be listed
2) Network Key = Password used to access your Wi-Fi Network
Ex. BMXGuy456!
Ex. Millionare$!!!
This is the password you created when you setup your wireless network, meaning it may not (and should not be for better security purposes) the same password as you use for your Apple ID, email etc.
NOVICE HINT: So if for example a friend came to stay with you and wanted to connect to your "secured wifi" meaning there is a lock next to it, you would give them this password.
EXTRA INFO:
Why do I need this info anyway?
Because just like anyone who wants to use your wifi when they come over, the printer needs to understand what to connect to, therefore it basically needs the network name to know "WHAT" to connect to, and the "PASSWORD" in order to access that network.After much stumbling around, I also discovered this answer. I picked up the 2270DW used, without disc or manual, so downloaded what I needed from the Brother site, but the Brother Mac OSX instructions feel as if they're written by a non-Mac user. I am on OSX 10.7.5, using an Airport wireless unit in Bridging mode (because I have to use a provider's router at the front end of my setup). But once I picked my Airport network name through the Brother Wireless Setup Utility and then typed my network name in the SSID box and my network password in the Network Key box ("es" --- I think the "network key - i.e. password" had to be confirmed a second time) after waiting for the utility to process the information, it worked like a charm.
-
Need to configure different SSIDs on same VLAN on 1142
We're having a problem with interference in the B/G range due to the large number of access points owned by other companies in a fairly small area. The various laptops keep deauthenticating, which is causing problems with applications. I'd like to configure two SSIDs on the same VLAN but have them broadcasted on different frequencies. The AP complained about the configuration when I added the Company5.8 SSID below stating another SSID can't be added to a VLAN, but it shows in the configuration. Does any one have a suggestion as to what I can try? Thanks
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 1 mode ciphers aes-ccm
encryption vlan 3 mode ciphers aes-ccm
ssid Moleculera Labs
ssid Moleculera Labs-guest
antenna gain 0
mbssid
channel least-congested 2412 2437 2462
station-role root
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio0.3
encapsulation dot1Q 3
no ip route-cache
bridge-group 3
bridge-group 3 subscriber-loop-control
bridge-group 3 block-unknown-source
no bridge-group 3 source-learning
no bridge-group 3 unicast-flooding
bridge-group 3 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
encryption mode ciphers aes-ccm
encryption vlan 1 mode ciphers aes-ccm
encryption vlan 3 mode ciphers aes-ccm
ssid Moleculera Labs
ssid Moleculera Labs-guest
antenna gain 0
dfs band 3 block
mbssid
channel dfs
station-role root
interface Dot11Radio1.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1.3
encapsulation dot1Q 3
no ip route-cache
bridge-group 3
bridge-group 3 subscriber-loop-control
bridge-group 3 block-unknown-source
no bridge-group 3 source-learning
no bridge-group 3 unicast-flooding
bridge-group 3 spanning-disabledAmjad, if I delete "encryption mode ciphers aes-ccm" what kind of encryption will the AP use?
Mohanak, I'm using the same encryption settings with VLANs
Here is the more complete configuration:
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname COMPANY-AP
no logging console
enable secret 5 *
no aaa new-model
no ip domain lookup
ip domain name COMPANY.local
dot11 syslog
dot11 ssid COMPANY-2.4
vlan 1
authentication open
authentication key-management wpa
mbssid guest-mode
wpa-psk ascii 7 *
dot11 ssid COMPANY-5.8
vlan 1
authentication open
authentication key-management wpa
mbssid guest-mode
wpa-psk ascii 7 *
dot11 ssid COMPANY-guest
vlan 3
authentication open
authentication key-management wpa
guest-mode
mbssid guest-mode
wpa-psk ascii 7 *
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 1 mode ciphers aes-ccm
encryption vlan 3 mode ciphers aes-ccm
ssid COMPANY-2.4
ssid COMPANY-guest
antenna gain 0
mbssid
station-role root
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio0.3
encapsulation dot1Q 3
no ip route-cache
bridge-group 3
bridge-group 3 subscriber-loop-control
bridge-group 3 block-unknown-source
no bridge-group 3 source-learning
no bridge-group 3 unicast-flooding
bridge-group 3 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
encryption mode ciphers aes-ccm
encryption vlan 1 mode ciphers aes-ccm
encryption vlan 3 mode ciphers aes-ccm
ssid COMPANY-2.4 (Want this to be COMPANY-5.8)
ssid COMPANY-guest
antenna gain 0
dfs band 3 block
mbssid
channel dfs
station-role root
interface Dot11Radio1.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1.3
encapsulation dot1Q 3
no ip route-cache
bridge-group 3
bridge-group 3 subscriber-loop-control
bridge-group 3 block-unknown-source
no bridge-group 3 source-learning
no bridge-group 3 unicast-flooding
bridge-group 3 spanning-disabled
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
no keepalive
interface GigabitEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface GigabitEthernet0.3
encapsulation dot1Q 3
no ip route-cache
bridge-group 3
no bridge-group 3 source-learning
bridge-group 3 spanning-disabled
interface BVI1
ip address 192.168.67.3 255.255.255.0
no ip route-cache
ip default-gateway 192.168.67.1
ip http server
ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
line vty 0 4
exec-timeout 30 0
password 7 *
login local
end
COMPANY-AP# -
Problem with wpa and hidden ssid
hi,
I have a powerbook g4 (1,67ghz). i am having trouble connecting to a netgear router mr814 v3 if i use wpa and hidden ssid, i get a message, that the router would not support wpa!
there is no problem with wep and hidden ssid or wpa with no hidden ssid.
is also have no problems with wpa and hidden ssid with an ibook.
the problems occur only with the powerbook with os x 10.3.9 as well as 10.4.2. even after the recent airport update, no change.
thanks for the help,
benI would use WPA and broadcast your SSID.
It use to be useful, but closing your Airport or wireless network (sometimes referred to as not broadcasting your SSID) is really no longer a real option when it comes to wireless security.
Unfortunately "Closed" networks, MAC access control lists, and reduction in transmission power are all more "feel good" security rather than real security. All these various approaches are dated and mistakenly lead to overconfidence.
WPA is your friend if you value wireless security.
My recommendation is not to worry about broadcasting your SSID but use WPA. This will be more secure than a closed WEP encrypted network. Closing your network makes it very difficult for neighbouring networks to see which channels are free thus causing potential interference problems.
Another thing to consider is that a closed network is still broadcasting and therefore is detectable (regardless of whether it is broadcasting a SSID). If someone was determined to hack into your network, then not broadcasting your SSID and MAC address access control is not going to stop them.
WPA is virtually uncrackable (only really vunerable to a dictionary attack if a real word is used as a password) and therefore will stop the casual user and the determined hacker. -
Lose Internet connection when I change the SSID
Hi everyone!
well, i bought a WRT160N router, and i have a problem that is annoying me.
I connected the Router to the modem, and all the wired connected PCs were working perfectly.
But then, i went to the setup page to configure the Wireless settings, and as soon I changed the SSID name, the connection internet connection dropped!
The only way i had to fix this was by making a Hard Reset.
after that, I also tryed changing values and settings from all the configuration tabs, and the wired connection was working properly, but as soon i changed any value from the Wireless tab, the internet connection dropped (even, in the diagnostics section, i could not do a ping to google. It says unknown host).
Here you have an image of this:
http://imageshack.us/photo/my-images/41/sinttuloesw.png/
I thought that this was a hardware related problem, and i returned the router for another wrt160n, and the problem persisted.
Also, i have the latest firmware
Any idea?I thought that a wireless client connects to the named SSID that you designate. If you change the SSID while clients are connected, that would be like the network disappearing as far as the clients are concerned. So you would have to reconnect the clients that were connected to that SSID network. Other wireless network parameters that you change would also cause disconnects, like changing the security, changing the passphrase, etc., you would have to reconnect clients with the new parameters that were connected at the time you made the changes.
-
Need Time Capsule to join new existing network after Uverse box swap SSID
When I first bought my Time Capsule it was creating my wireless network.
Then last year we moved to a new house, and got Uverse service. I successfully changed Time Capsule's config to join the existing Uverse network, so the TC does backup and nothing else. (The Uverse box is in the basement, so the TC connects to that network and all client machines over the Uverse wifi.)
Now I just had problems with Uverse (lost voice service, and so they swapped their box, which means I have a new SSID (and password). So I need to change the config of the TC to join the different existing network. I've tried connecting an Ethernet cable to both the WAN and other-Ethernet ports on the back of the TC, but the Airport Utility on that desktop still doesn't recognize the TC.
What do I do?Welcome to the discussions!
The problem is that the ethernet ports on the TC are not enabled when it "joins", so that type of connection between your computer and the TC won't work.
The other issue is that the TC is remembering the old wireless network and you can't access it that way any longer.
You'll need to perform a "hard reset" on the TC by holding in the reset button until the amber light blinks more quickly, then reconfigure the device using the settings from the new wireless network.
This will not affect your existing backups, but you will need to reset Time Machine to point it as the Time Capsule again.
Open System Preferences
Click Time Machine
Click Select Disk
Click your Time Capsule
Click Use for Backups
Message was edited by: Bob Timmons
Maybe you are looking for
-
Drag and drop attachments between two email windows
Hi together, my problem is easy. i cannot drag and drop attachements between two email windows using Apple Mail. On my old MBAir it was no problem. I do not know which configuration i have to change. To drag and drop to the desktob is no problem. Now
-
Synonym for Sequence e grant to other user
Hola, I have two user AAA e BBB In AAA I have this sequence SQ_NUMEAVVI I create in BBB user CREATE SYNONYM SQ_NUMEAVVI_AAA FOR AAAA.SQ_NUMEAVVIAnd from sql connection of user BBB I haven't problem to see this sequence, but when I compile this functi
-
I'm trying to figure out how I can see the equation of the line on the graph I just created. I'm using the OS X Mavericks version of Numbers.
-
Sharing multiple address books in 10.7 Lion
I have 3 distinct groups that are accessing my server. Each requires it's own unique shared address book. I'm at a loss for setting this up in Lion. I had a (sloppy I think) solution for this under Snow Leopard server involving a shared user account
-
Due to a rash of HD failures, I recently had to move all my files to a new drive. That solved the problems except for one: my Library folder was re-created from scratch so all my settings, mail, etc all disappeared. I *did* manage to back up the Libr