SSO and Portal down after upgrade from AS 10.1.2.0.2 to 10.1.2.3

SSO and Portal is down after upgrade from AS 10.1.2.0.2 to 10.1.2.3. All others are running fine. Any similiar experience and solution?
Thanks.
Andy

cn=XXX information is missing for the SSO Server (orasso) when going to http://servername:7777/pls/orasso/orasso.home. Is that causing the problem? If so, how can I resolve it?
Thanks.
Andy

Similar Messages

  • Portal down after upgrade from 10.1.2.2 to 10.1.2.3

    Hi Folks,
    The weekend we upgraded the infrastructure/mid-tier from 10.1.2.2 to 10.1.2.3 and did the same for the metadata repository. We noticed since then portal is down though OC4J_Portal is up. Any idea how the upgrade would cause this and how to fix it?
    Thanks
    Troy

    Hi Erik,
    I checked the metalink note you recommended and sure enough my PortalListeniongHostPort and HTTPPort did not match. I changed them and added the root certificate in b64InternetCertificate.txt and it now shows as up. Thank you so much for referring me to that document. It is greatly appreciated.
    Troy

  • I have a big problem with Lion and PGP. After upgrading from snow leopard to lion I cannot access my PGP drive which was generated under snow leopard. PGP does not start but gives a notion that lion cannot work with my PGP version. Solution?

    After upgrading from Snow Leopard to Lion I cannot access a PGP drive which was generated under snow leopard. PGP does not start. When I try to start I just receive a message that Lion cannot work with PGP. How can I now access important and confifential informatio which I have stored in PGP (snow leopard). Do I have to move back to snow leopard. If so, how can I do this? 

    If you have this product,
    http://www.symantec.com/business/support/index?page=content&id=TECH165159
    you have to go back to Snow Leopard.
    To re-install SL, back up your home directory, format and re-install.

  • IBook shuts down after upgrading from 10.3.3 to 10.3.9

    Hi...I tried upgrading an old iBook G3 700 MHz from OS X 10.3.3 to 10.3.9 (combo). Now it won't finish
    starting up. I press power, I do hear the chime and get to the point where the first screen with
    the simple apple logo shows, but then after 5 seconds it shuts down again. I do hear the disk
    going briefly during this time.
    I booted with the hardware diagnostics CD that came with the machine, and all tests passed OK
    - both the quick tests and the extended tests.
    Wanted to just try reinstalling from the Panther CD set that I have, but I've found that I can't
    boot from those CDs - does the same thing, shows the apple logo, then shuts down after 5 seconds.
    I tried restarting in single user mode, it doesn't seem to get very far - I get the black screen, it
    prints about 5 lines of information, then one line saying "Using 983 buffer headers..." and then
    it shuts down. Seems like it's not getting far at all into the boot process.
    Any thought's on what to try next? Wish I could just reinstall, wiping the slate clean, but even
    that doesn't work!
    Thanks in advance for any help...
    - Bruce

    Success! This is so bizarre...
    I have two Mac laptops, the iBook 700 MHz that's having the problem, and a newer
    PowerBook G4. A few days ago I wanted to recharge the iBook...I've been very diligent
    up to this point to use the correct charger with each laptop, the one that each came
    with.
    I got lazy this last time...plugged the charger for the newer PowerBook into the
    older iBook. Then I did the upgrade, and then I shut down the machine. It was after
    that that I had problems restarting.
    I got suspicious just now and looked at each charger. Thought they would be
    interchangeable, but on looking at them the charger for the older iBook says output
    is 24v 1.875A, while the one for the PowerBook is 24v 2.65A.
    Knowing that there's a PMU (Power Management Unit) in these machines and that it
    has settable parameters, I thought, what the heck, plug the correct charger back into
    the iBook, just to see what happens. Voila, it started up OK!!!
    What the heck ?!?!
    I'm pretty well versed in computers (work with Unix and Linux regularly, love the
    Mac OS X command line!), just don't understand everything that goes on under the
    hood with the Macs these days.
    Just to get some final closure on this problem, can anyone explain why doing what
    I did resolved the issue? I'd really like to learn from my mistakes.
    Thanks to Rhonda and S.U. who responded so quickly for my plea for help!
    - Bruce

  • Photoshop CS6 issue with shortcuts and my keyboard after upgrade from CS5

    I recently upgraded from CS5 Extended to CS6 Extended on my Mac (Mavericks), but installed it in English instead of German this time. I transferred most of my presets just fine, but none of the keyboard shortcuts were working. All I got was an unequal sign for all shortcuts and even manually changing them didn't get them to work. I found a few discussions about this issue and ended up adding a German keyboard, as I am always on the Romaji setting of my Kotoeri (Japanese) keyboard. That seemed to solve the issue, but only if I change to the German keyboard before opening Photoshop. Shortcuts don't work in CS5 anymore either unless I do. Sometimes the shortcuts also stop working a while after I change back to the Kotoeri keyboard.
    Now I would like to know if there is any way to get around this issue. Isn't there a way to get my shortcuts working again without constantly having to change keyboards? I much prefer the Kotoeri one since the icon for the German keyboard in my menu bar looks extremely obnoxious, in my opinion. It's mostly a cosmetic thing to me, but I would love to get everything back to the way it was before.
    I'd much appreciate any advice or help.

    I am having a similar problem. Just upgraded to Apple Yosemite and all none of my keyboard shortcuts are working in a clean install of Photoshop CS6. Every menu item has some form of the ≠ sign. I've trashed the .plist file, rebuilt permissions, etc. Even basic keyboard commands, like Command-N for NEW or Command-Q for QUIT do not work. In fact, many don't show up in the menu at all. I don't have this issue in InDesign CS6 or Illustrator CS6. Every once in awhile, maybe 1 time out of 20, menus and keyboard shortcuts work properly, but I can't find any pattern.

  • Delete and Re-install after upgrade from single app to full cloud suite?

    Hi,  I recenly upgraded to the full creative cloud membership from a single app subscription of Illustrator last month.
    I opened an illustrator file today from the single app installation and recieved a warning that I no longer have access to the program. Do I need to delete this version of illusrtrator and re-install from my new creative cloud suite membership?  Or is there a way to register the current downloaded version of Illustrator with my new full suite subscription?
    Thanks for the help

    Hi bella1439402,
    You don't need to uninstall illustrator from your computer.
    You can simply launch the program ---> it will give you a pop up that your subscription is expired or the trial is expired ---> in the same window there will be a button 'License this software' ---> click on 'License this software'
    ---> Sign in with your Adobe Id on whihc you have the full creative cloud subscription ---> your subscription will be activated.
    You can install rest of the products.
    Thanks
    Kapil

  • SLOW logins and account switching after upgrade from Tiger to 10.5.6?

    Just bought and installed 10.5.6 as part of the MacBoxSet and had no problems installing the software. But when I tried to login, it took forever and still takes between 3 & 5 minutes to login in at boot-up or to change accounts. Gave up on trying to use fast switching. It just stalls everything. Most software seems to be running fine now. Did have some issues with "MAIL," but seem to have overcome those by deleting preferences.
    Any help I can get would be greatly appreciated. THANKS ! !
    Model Name: Power Mac G5
    Model Identifier: PowerMac7,2
    Processor Name: PowerPC 970 (2.2)
    Processor Speed: 2 GHz
    Number Of CPUs: 2
    L2 Cache (per CPU): 512 KB
    Memory: 7 GB
    Bus Speed: 1 GHz
    Boot ROM Version: 5.1.4f0
    ATI Radeon X800 XT / VRAM 256 MB

    By going to my Mail folder in my Library folder (~/Library/Mail) and deleting all files except any folders and then opening Mail and re-importing, everything comes up properly.

  • Impact on Custom / Std IDOC after upgrading from 4.7 to ECC 6.0

    I am in Upgrade project (4.7 to ECC 6.0).
    What will be the impact of the existing Custom and Std IDOC after upgrading from 4.7 to ECC 6.0 and if any impact, what are precautionary steps to be taken to work as it is.
    Will there be any Impact on ALE also ?
    Thanks & Regards
    Khaleel

    closed.

  • After upgrading from Snow Leopard to Mountain Lion, the text preference, Middle Eastern, causes Photoshop CS6 to slow down.  Can this be fixed?

    After upgrading from Snow Leopard to Mountain Lion, and setting the text preference, Middle Eastern, causes Photoshop CS6 to slow down.  Can this be fixed?

    I'm Win, not Mac, but I do have a couple saved messages
    Mac 10.8.3 Bug w/Encore and BluRay http://forums.adobe.com/thread/1198709
    -create folder not ISO http://forums.adobe.com/thread/1216127

  • Graphics instability and crashing after upgrade from FF 32 to 33

    Soon after upgrading from 32.0.3 to 33 (Windows 7), I was seeing occasional flicker-like split-second black flashes. (I *think* this was mostly when opening new pages, but I don't recall for sure...maybe also when scrolling). Then a few minutes later I was scrolling a page with my laptop touchpad and the screen flashed completely black, stayed that way for about a second, and then came back up with a Windows message that Intel Graphics had recovered from a crash. (Which is doubly interesting given that FF set to use my discrete NVIDIA graphics on this computer.). I haven't seen anything like this happen in the nine months I've had this laptop, with or without FF open. There was also a message that FF had crashed.
    Then I restarted FF, and all was going OK, except that I believe I still saw a few split-second "in the blink of an eye" black screens as I opened new pages. But then I went to Google Maps, and was dragging a map upwards. But instead of the lower portion of the map moving into view, I only got a blank white screen. The further up I dragged the map, the more of the the screen that was blank white, until it was completely white. Then FF crashed again.
    I thought the new FF native H.264 might be causing the issue so I disabled it and restarted FF. But then I went back to Google Maps, tried the same thing and had the same issue (but no associated crash, although I closed FF very soon after I saw the odd graphics behavior recurring so maybe I didn't give it enough "time to crash").
    I re-installed 32.0.3 and all the issues went away. FWIW, I've had occasional crashes and slowdowns with 32 and other recent versions. (I could recover from the slowdowns just by restarting FF.) Most of those issues seemed to be associated with Adobe Flash. That behavior was an occasional annoyance but nothing of the magnitude of what happened when I tried FF 33. I don't know if this latter observation adds anything, but I just thought I'd throw it out there. Fyi, the laptop has 2.4 Ghz CPU (Intel i7) and 16GB memory.
    Any ideas? Thanks.

    Today when I noted that Lenovo still hadn't released an updated driver specifically for the Intel Graphics, I went back and installed a Lenovo NVIDIA Optimus update that I had tried 4 or 5 months ago but had subsequently reversed because it had created problems with Firefox. (Specifically, it was causing Firefox context menus to render slowly and incompletely.) Not only does the NVIDIA update no longer cause the FF context menu problem, it seems to have *solved* the problem I posted about here. It updated the NVIDIA driver ("GPU #2" above) from version 9.18.13.1269 to version 9.18.13.3302.
    This makes some intuitive sense, since -- as I said above -- I have Optimus set to use the NVIDIA graphics with Firefox instead of Intel. (I had thought that, based on what I read in Lenovo support, the NVIDIA Optimus update might install a new Intel Graphics driver as well, but the Intel driver is still shown as the same version listed above (8.15.10.2725). (I don't know whether or not these driver numbers might be Lenovo-specific.)
    Anyway, the NVIDIA Optimus update fixed my problem, so thanks for pointing me in the direction of graphics drivers. (I suppose there's also a small possibility that something had simply gone awry with my first update to FF 33, and that what really solved things was simply reinstallingl...)

  • My itunes will stop working and shuts down after 5 to 10 minutes playing. I have the most recent updates. How can I repair or correct this from crashing?

    My itunes will stop working and shuts down after 5 to 10 minutes playing. I have the most recent updates. How can I repair or correct this from crashing?

    Hello there, jbenjaminii.
    The following Knowledge Base article offers up some great recommendations for troubleshooting the issue you're describing:
    iTunes for Windows XP: Troubleshooting unexpected quits, freezes, or launch issues
    http://support.apple.com/kb/ts1421
    Thanks for reaching out to Apple Support Communities.
    Cheers,
    Pedro.

  • Not booting from 10.4.8 volumes after upgrade from 10.4.7

    I'm sorry to report that my aged G4 450 MHz AGP with 4 internal Hard disk drives no longer boots from any of the 2 volumes upgraded to Mac OS X 10.4.8 as soon as it was started from another volume!
    All was working fine as long as 10.4.7 was installed on the 2 232 GB disks connected to the SIIG ATA133 controller. I could boot from any OS on any of the 4 disks, 5 partitions:
    internal ATA66 bus:
    18 GB disk, 2 partitions: 'IBM_18GB' with OS 9.2.2 and TechTool Pro's 'eDrive' with 10.4.7
    71 GB disk, 1 partition 'IBM_71GB' with OS 9.2.2
    PCI SIIG ATA133 controller:
    232 GB disk, one partition 'I1232GB' with 10.4.7, now upgraded to 10.4.8 and no longer bootable
    232 GB disk, one partition 'I2232GB' with 10.4.7, now upgraded to 10.4.8 and no longer bootable
    Now I can only boot from the Mac OS 9.2.2 or the eDrive 10.4.7 partitions.
    What I did so far: 'I2232GB' was my main OS X startup volume, 'I1232GB' contains a clone of it, plus additional folders like software base and backups.
    After upgrading 'I2232GB' to Mac OS X 10.4.8 through Software Update and repairing permissions all was OK as long as the Mac was just shut down or re-started: it always booted up in Mac OS X 10.4.8 from 'I2232GB' without any problems.
    The next day I booted from 'I1232GB' to do the same there.
    Afterwards I could no longer boot in Mac OS X 10.4.8 from 'I2232GB' nor in in Mac OS X 10.4.8 from 'I1232GB': it just gets to the grey screen with the Apple logo, but the round circle underneath indicating some progress never appears. I left it there for hours: it just hangs.
    With the Option key held at startup I could boot from the other partitions with Mac OS 9.2.2 or the eDrive with 10.4.7. None of their Startup Control Panels was able to get me back to 10.2.8!
    So I booted from the TechTool Pro 4.5.1 DVD to Optimize both volumes, 'I1232GB' & 'I2232GB', always Files only.
    Then I booted from the DiskWorrior 3.0.3 CD to rebuild the directories of both volumes, 'I1232GB' & 'I2232GB'.
    Still I can not boot from either 'I1232GB' or 'I2232GB' in Mac OS X 10.2.8!
    Downloaded the Mac OS X 10.2.8 Compo Update (for PPC) and installed it onto both 'I1232GB' & 'I2232GB' while booted from the eDrive which I keep on Mac OS X 10.4.7 - no luck either, still I can not boot from either 'I1232GB' or 'I2232GB' in Mac OS X 10.2.8!
    Then I backed up the users folder from 'I2232GB' onto 'I1232GB', booted from Mac OS 9.2.2 and used Intech's Hard Disk Speedtools 3.6 to format 'I2232GB', afterwards initialized it with Alsoft's Plus Maximizer Extension for a Block Size of 512 Bytes.
    Installed Mac OS X 10.4 from DVD, as well as iLive '06 and upgraded everything to the latest releases with Software Update. All was working fine with all the required reboots until another startup volume was chosen: afterwards again I can no longer boot back into Mac OS X 10.2.8 on the fresch installed 'I2232GB'!
    Any help would be appreciated.
    Here is some information found by System Profiler from Mac OS X 10.4.7, eDrive, let me know if you need more:
    Hardware Overview:
    Machine Name: Power Mac G4 (AGP graphics)
    Machine Model: PowerMac3,1
    CPU Type: PowerPC G4 (2.8)
    Number Of CPUs: 1
    CPU Speed: 450 MHz
    L2 Cache (per CPU): 1 MB
    Memory: 2 GB
    Bus Speed: 100 MHz
    Boot ROM Version: 4.2.8f1
    Serial Number: XA00715VHSF
    Sales Order Number: M7628LL/A
    ATA Bus:
    IBM-DPTA-372050:
    Capacity: 19.12 GB
    Model: IBM-DPTA-372050
    Volumes:
    IBM_18GB:
    Capacity: 13.12 GB
    Available: 6.96 GB
    eDrive:
    Capacity: 6 GB
    Available: 3.03 GB
    IBM-DTLA-307075:
    Capacity: 71.59 GB
    Model: IBM-DTLA-307075
    Volumes:
    IBM_71GB:
    Capacity: 71.59 GB
    Available: 39.65 GB
    ATA Bus:
    PIONEER DVD-RW DVR-107D:
    Model: PIONEER DVD-RW DVR-107D
    Firmware Revision: 1.21
    Interconnect: ATAPI
    Burn Support: Yes (Apple Shipped/Supported)
    Cache: 2000 KB
    IOMEGA ZIP 100 ATAPI:
    Model: IOMEGA ZIP 100 ATAPI
    ACARD,6880M:
    Name: ACARD,6880M
    Type: scsi
    Bus: PCI
    Slot: SLOT-C
    Vendor ID: 0x1191
    Device ID: 0x0009
    Subsystem Vendor ID: 0x1191
    Subsystem ID: 0x0009
    Revision ID: 0x0003
    SCSI Parallel Domain 65536:
    Initiator Identifier: 7
    ATA HDT722525DLAT80:
    Capacity: 232.89 GB
    Manufacturer: ATA
    Model: HDT722525DLAT80
    Revision:
    Removable Media: Yes
    BSD Name: disk2
    OS9 Drivers: Yes
    SCSI Target Identifier: 0
    SCSI Logical Unit Identifier: 0
    S.M.A.R.T. status: Not Supported
    Volumes:
    I1232GB:
    Capacity: 232.89 GB
    Available: 14.1 GB
    Writable: Yes
    File System: HFS+
    BSD Name: disk2s3
    Mount Point: /Volumes/I1232GB
    ATA HDT722525DLAT80:
    Capacity: 232.89 GB
    Manufacturer: ATA
    Model: HDT722525DLAT80
    Revision:
    Removable Media: Yes
    BSD Name: disk3
    OS9 Drivers: Yes
    SCSI Target Identifier: 2
    SCSI Logical Unit Identifier: 0
    S.M.A.R.T. status: Not Supported
    Volumes:
    I2232GB:
    Capacity: 232.89 GB
    Available: 180.11 GB
    Writable: Yes
    File System: Journaled HFS+
    BSD Name: disk3s3
    Mount Point: /Volumes/I2232GB
    The RAM consists of 4 identical modules and is about 1 year old:
    DIMM0/J21 to DIMM3/J24:
    Size: 512 MB
    Type: SDRAM
    Speed: PC133-333
    Status: OK
    Many thanks for your help!
    Josef
    Apple G4 AGP   Mac OS X (10.4.8)   4 internal hard disks, dual layer DVD-RW, 2GB RAM

    What I did so far: 'I2232GB' was my main OS X
    startup volume, 'I1232GB' contains a clone of it,
    plus additional folders like software base and
    backups.
    After upgrading 'I2232GB' to Mac OS X 10.4.8
    through Software Update and repairing permissions all
    was OK as long as the Mac was just shut down or
    re-started: it always booted up in Mac OS X 10.4.8
    from 'I2232GB' without any problems.
    The next day I booted from 'I1232GB' to do the same
    there.
    Afterwards I could no longer boot in Mac OS X 10.4.8
    from 'I2232GB' nor in in Mac OS X 10.4.8 from
    'I1232GB': it just gets to the grey screen with the
    Apple logo, but the round circle underneath
    indicating some progress never appears. I left it
    there for hours: it just hangs.
    With the Option key held at startup I could boot from
    the other partitions with Mac OS 9.2.2 or the eDrive
    with 10.4.7. None of their Startup Control Panels was
    able to get me back to 10.4.8!
    So I booted from the TechTool Pro 4.5.1 DVD to
    Optimize both volumes, 'I1232GB' & 'I2232GB',
    always Files only.
    Then I booted from the DiskWorrior 3.0.3 CD to
    rebuild the directories of both volumes, 'I1232GB'
    & 'I2232GB'.
    Still I can not boot from either 'I1232GB' or
    'I2232GB' in Mac OS X 10.4.8!
    Downloaded the Mac OS X 10.4.8 Compo Update (for PPC)
    and installed it onto both 'I1232GB' & 'I2232GB'
    while booted from the eDrive which I keep on Mac OS X
    10.4.7 - no luck either, still I can not boot from
    either 'I1232GB' or 'I2232GB' in Mac OS X
    10.4.8!
    Then I backed up the users folder from 'I2232GB'
    onto 'I1232GB', booted from Mac OS 9.2.2 and used
    Intech's Hard Disk Speedtools 3.6 to format
    'I2232GB', afterwards initialized it with Alsoft's
    Plus Maximizer Extension for a Block Size of 512
    Bytes.
    Installed Mac OS X 10.4 from DVD, as well as iLive
    '06 and upgraded everything to the latest releases
    with Software Update. All was working fine with all
    the required reboots until another startup volume was
    chosen: afterwards again I can no longer boot back
    into Mac OS X 10.4.8 on the fresch installed
    'I2232GB'!
    I found several typos in above post, wherever it was 10.2.8 it should have read 10.4.8 - I'm very sorry for confusing you, this would not have made sense, but I found no way to edit the existing text therefore I modified the quote of it here.
    I do not need Mac OS X 10.2.8 back, but it would be nice to boot back in Mac OS X 10.4.8 from another volume as the current one - which was working fine before with Mac OS X 10.4.7.
    Many thanks,
    Josef

  • SSO and portal timeout  -- other bug?

    ...this is very probably related to the other post talking about SSO and portal timeout...
    I am having another weird issue with dotnet portlets that uses inline refresh (done automatically by dotnet accelerator) and SSO.
    When you let the portal session expire, and then click on a button/link within a portlet (hence generate an inline refresh gatewayed request), the full portal window (header/footer etc...) appears within the portlet, instead of the portlet content alone.
    I did some http traces (see below) and it seems the problem is due to the windows SSOLogin.aspx (we are using windows auth SSO) not taking the requested portlet gatewayed request url as a post login redirect info... but taking instead the current page url (which is wrong)
    Thus, after the gatewayed portlet request is successfully authenticated by the SSOLogin.aspx component, it is automatically redirected to the wrong urll...making the full portal page refresh into the portlet.
    So my question is: have anyone already seen such behavior? And has anything been done to fix this?
    It really seems like a bug with the SSO servlet...but maybe i am doing something wrong...Just want to have your thoughts on this.
    Thanks,
    Fabien
    ============================================================================================
    HTTP Trace:
    POST     302     Redirect to /portal/sso/SSOLogin.aspx?in_hi_userid=15046&space=CommunityPage&parentid=1&cached=false&control=SetCommunity&PageID=0&CommunityID=205&parentname=Login     http://your.portal.com/portal/server.pt/gateway/PTARGS_0_15046_362_205_0_43/http%3B/your.portletserver.com/yourapp/youraspx.aspx
    GET     401     text/html     http://your.portal.com/portal/sso/SSOLogin.aspx?in_hi_userid=15046&space=CommunityPage&parentid=1&cached=false&control=SetCommunity&PageID=0&CommunityID=205&parentname=Login
    GET     401     text/html     http://your.portal.com/portal/sso/SSOLogin.aspx?in_hi_userid=15046&space=CommunityPage&parentid=1&cached=false&control=SetCommunity&PageID=0&CommunityID=205&parentname=Login
    GET     302     Redirect to http://your.portal.com/portal/server.pt?in_hi_userid=15046&space=CommunityPage&parentid=1&cached=false&control=SetCommunity&PageID=0&CommunityID=205&parentname=Login     http://your.portal.com/portal/sso/SSOLogin.aspx?in_hi_userid=15046&space=CommunityPage&parentid=1&cached=false&control=SetCommunity&PageID=0&CommunityID=205&parentname=Login
    GET     200     text/html; charset=utf-8     http://your.portal.com/portal/server.pt?in_hi_userid=15046&space=CommunityPage&parentid=1&cached=false&control=SetCommunity&PageID=0&CommunityID=205&parentname=Login

    I have this happen in v6.0 sp1. We have worked around the problem with a bit of work and synchronization of settings. Below, I've outlined how we've worked around the problem (which is indeed a problem that should be fixed). Also, if you have a load balancer, you'll need to set your session timeout on the load balancer to a bit more than the refresh rate that you set for your communities and My Pages.
    Resolving the Portlet Timeout / Refresh Problem in ALUI Portal_
    Problem: Users occasionally receive the portal page within a portlet error
    Cause: The root cause has not been determined; however it appears that the primary event that exhibits the behavior is when a teammember’s session has expired on the portal server and they then utilize a .NET form-based portlet which refreshes in place. Because we are using WIA SSO to enable automatic logins to the portal, it makes the error seem to occur randomly.
    Resolution:
    The workaround solution is to – 1) increase the portal session timeout on the portal web servers from the default 20min to 4 hours, and 2) set the MyPage refresh interval setting for all portal users to 3 hours. The setting name is a bit of a misnomer, as it will actually refresh the entire portal page automatically if the user is idle on either a My Page or a Community Page, as these are the only two places that portlets reside.
    Increasing the portal session timeout:
    The portal session timeout is controlled in two places, and both settings should match. On the portal virtual directory in IIS, edit the configuration and increase the timeout setting to 240 (minutes). Then, edit the portal application’s web.config file (d:\portal\ptportal\6.0\webapp\portal\web\) and increase the sessionState Timeout variable to 240. Editting the config file will require you to restart the services before you see the change.
    Initial setting of the MyPage refresh interval:
    The initial setting will need to be done by a SQL script in order to apply it to all existing users. The Default Profile should also be updated so that all new user synched from AD will have this setting applied automatically.
    /* Delete refresh interval settings for all users first so that there are no conflicts on the inserts */
    DELETE FROM portaldbuser.ptprefs WHERE prefname = 'intMyPageRefreshRate'
    /* Insert desired page refresh setting for all users */
    INSERT INTO portaldbuser.ptprefs (userid,gadgetid,prefclassid,prefobjectid,prefname,prefvaluetype,prefvalue,pagenumber) SELECT objectid,0,0,0,'intMyPageRefreshRate',3,180,0 FROM portaldbuser.ptusers
    From Administration, access the Default Profiles utility. Check the Default Profile entry and click on the Edit Profile Layout link. Click on the My Account link in the Portal Settings portlet and then on the Display Options link on the next page. In the Page and Portlet Settings, update the Your My Page will be updated: setting to 4 hours. Click Finish twice to return to Administration.
    Updating the MyPage refresh interval:
    To update the setting just modify the insert portion of the SQL script. Change the prefvalue number (180) to the desired timeout in minutes and rerun both statements of the script.
    The Default Profile should be also be modified per the instructions above.
    I hope this helps...
    -tom

  • Query slows down after upgrade

    Hi,
    After upgrade from oracle 10 to oracle 11 a simple query is slowing down alot.
    Same amount of records, same table only the execution cost time is increased
    Can someone give me some feedback over this problem?
    Can I check some things to look into the problem?
    Thx in advance.
    Greetings
    query:
    Select nvl(sum(a.BM_OPENSTAAND_DEBET- a.BM_OPENSTAAND_CREDIT),0)
    from bh.bh123gh a
    where
    a.F123_AR_NR>='4400000000' and
    a.F123_AR_NR<='4404000000' and
    a.F123_KL_LEV_AR_NR='0631001000' and
    a.SRT_REK=2 and
    a.F123_BKJR>=0000 and
    a.F123_BKJR<=2011 and
    a.F123_FIRMA=2
    explain plans
    oracle 11
    cost 1,792
    Bytes: 38
    Cardinality: 1
    oracle 10
    cost 1,594
    Bytes: 38
    Cardinality: 1

    >
    After upgrade from oracle 10 to oracle 11 a simple query is slowing down alot.
    Same amount of records, same table only the execution cost time is increased
    Can someone give me some feedback over this problem?
    Can I check some things to look into the problem?
    Thx in advance.
    >
    Is it just one query or all queries are behaving strangely? If it's just one query, do a trace and see where it's slowing down.
    In the meanwhile, you can also modify the optimizer_features_enable parameter at session level and check the explain plan.
    Alter session set optimizer_features_enable='10.2.0.5';
    Now test the query.
    By the way, if you are just worried about the COST factor, you can just ignore it. COST by itself has no real meaning. You will only have to look at the response time.
    Regards

  • Very slow encoding after upgrade from 5.03 to 5.5 with MXO2 mini

    Hi all.
    After upgrading from CS5.03 to 5.5 my encoding now takes 5 times as long. A 2 minute HD Video file would take 2 minutes, and still does on the PC I haven't upgraded (identical almost) but now with CS5.5 it takes almost 11 minutes.
    Some explanation....
    I create HD MJPEG files on a PC with Blackmagic Decklink.
    I transfer these files to an HPz800 which used to run CS5.03 with Matrox Utils 5.1.1.37 and an MXO2 Mini with Max. (Nvidia Quadro fx4800 and 12GB of RAM)
    On a Blackmagic timeline HD 1080i MJPEG with filters of Auto Color, Fast Color Corrector and Gamma correction a 2 minute timeline would encode in 2 minutes give or take a couple of seconds.
    Now with CS5.5 and Mtx 5.5 an identical file takes 11 minutes to encode to Microsoft avi - Matrox 1920 x 1080i - 25fps.
    If I remove the filters (which I need to be able to use) it will come down to 2 minutes as it used to be.....so it seems to be the filters are now slowing things down when they never used to. I have never rendered before exporting. Ever. So this time I tried rendering first and it brought the 11 minutes down to 7 minutes but when taking into account the 4 minutes rendering time I am no better off.
    I have updated CS5.5 to CS 5.5.1 and MTX Utils to 5.5 and then 5.5.1 and it makes no difference. Still 11 minutes to decode 2 minutes with three filters, which is exactly what I have always been doing but now it doesn't work....
    Can anybody help? or make a suggestion as to why using filters in 5.5 now multiplies the encode time by 5 when it never used to. Everything else bar Matrox Utils on this machine is as it was before the upgrade to 5.5 and as I say my older machine is still 5.03 it can do it all in 2 minutes even with the filters intact.
    So have I really spent a small fortune upgrading to make my output 5 times slower. Not happy......

    To go further, every single encode that I have done is slower than it was before with CS5.01 or 5.03.
    This is odd because going from Blackmagic to any other codec doesn't necessarily need the Matrox box or Matrox utils
    Blackmagic HD or SD to
    Matrox HD
    QT HD MP4
    QT SD DV25
    DV AVI SD
    Mpeg2 - DVD
    Every single encode is slow by 2x to 6x.
    Why should Blackmagic HD to QT MOV MP4 take twice as long as it used to...... having said that The speeds I am seeing now are what it was like before I attached the box in the first place, whether a Matrox codec was involved or not.... It is acting like a blocked funnel. when it used to be a lovely wide and clear funnel.
    Anyway Matrox have reproduced the problem and are investigating, so hopefully there will be an answer soon....

Maybe you are looking for

  • Multiple place holders in master slide

    Hello all, I would like to create a master slide with more than one place holder. Is that possible and how can I do it. Thank you all for the time you spend giving others your insight and knowledge. Mireille

  • How to reset partial clearing item:

    In my case, I have 5 Downpayment requests and cleared them in one bank posting. But some months later, I found one item is mistake and should be reset and reversed. At the same time other 4 items had been further delt with and can't be reversed again

  • Advice needed on Rendering XSL:FO

    Hi, I'd like some advice on rendering xsl:fo files. I'm in the early stages of developing a component that can render xsl:fo content. xsl:fo is an xml format for laying out content on paper, a bit like TeX. Normally xsl:fo content is generated using

  • Errors When Syncing iPhone

    Yesterday, I accidentally closed iTunes while my iPhone 3G was restoring from a backup, the back up was about 2/3rds done. I checked my phone, and it looked like all of my stuff was restored, though I'm sure there were some things that didn't restore

  • My MacBook Pro shutdown after it said my USB was draining to much power and now won't turn on please help

    Hi my MacBook will not turn on after it said my USB was draining to much power, and it shut down and now won't turn back on please help