ST03n Data missing for few days

Hi All,
While checking the total data in workload in expert mode of st03n. I can see data till 15th April and can see today's data.
But entries of days after 15th till today are missing.
Stat collector job ran fine during this period and did not get canceled.
The issue is in an ECC production system. We are working on ECC6.0.
Can any one please help to resolve this issue.
Thanks !
Varun

Hi Varun,
Please go to Sm37 and check SAP_COLLECTOR_FOR_PERFMONITOR job is running fine...
Also check Note 16083 - Standard jobs,reorganization jobs
Apart from this there is a link on help.sap where you can know about how to display contents in workload databs..
http://help.sap.com/saphelp_nw70/helpdata/EN/4c/0f0e422efcdf2ce10000000a1550b0/frameset.htm
Hope this helps.
Please revert back if still the problem persists.
Thanks You,
Shobhit Garg

Similar Messages

Why the ipad ranking is missing for few days in some itunes stores ?

Are you aware of some modification in the itunes store concerning ipad ? As I am spending marketing money to promote ipad app. I need this ranking.
Thanks for your help.

Thanks for your help! Yes, they are available but in the German iTunes Store only. Some older songs are available even in the US iTunes Store, but not the new songs from those German artists mentioned above.
I cannot provide a German billing/paying info because I live in California. I would like to switch over to the German iTunes store to buy the albums available there, however, I do have a German iTunes Card but you still need to provide a valid card (visa,master card etc) to purchase songs from the German iTunes Store (I wish the German iTunes gift card itself would be enough, this would make everything easy for many people).
Please help me out and do I need to create a new Apple ID associated ONLY with the German iTunes Store?
Thanks,
shindymagjeder

How can i shut down depreciation for an Asset for few days??

Hi Friends,
How can i shut down depreciation of a particular Asset for few days say 5 days??
I have done the necessary changes in Time dependent tab like checked asset shut down and in AFAMA i changed the shut dawn as YES.
The only problem i am in is "how can i maintain the 5 days like from 10.05.2009 to 14.05.2009
If i go to MORE INTERVALS then only From date is available over there.There is no To date opition.
How can i maintain To Date??
Plz suggest.
Regards,
Sumaya

Hi
Go for shut down approach. But your depreciation key should allow shut down. check your depreciation key configuration
In asset master data
Go to time dependent terms,
Define the appropriate time interval for shutdown
Set the shutdown indicator
The system does not calculate the depreciation for the shut down period,
The useful life of the asset will increase to the extent of shutdown period.
When you remove the shutdown indicator, system automatically resumes the depreciation calculation.
Regards
Tanmoy

Query with SQL-SP gives error, if not used for few days

Hi All,
I have observed that if we do not use some of queries (which usage SQL SPs) for few days, then it stops working.
But when we go in SQL and execute the SP, the query in SAP starts working, without making any change either in query or the SQL-SP.
Can anybody throw light on this ? I guess it has some connection with SQL-SP behaviour.
Thanking you in advance ,
Samir Gandhi
Edited by: Rui Pereira on May 1, 2009 1:28 PM

Hi Gordon,
Please note the function of the SP is to bring selected data from tables, for example to bring Purchase details (I have copy pasted the SP at bottom of this message).
These are not SP_notif...
These SPs are called from the SBO query.
Once we execute the SP in SQL, then it starts working with SBO also.
set ANSI_NULLS ON
set QUOTED_IDENTIFIER ON
GO
ALTER Procedure [dbo].[pGetPurchaseRegister]
     @StartDate datetime,
     @EndDate datetime
as
if exists (select * from dbo.sysobjects where id = object_id(N'[dbo].[tmpPurchaseReg1]') and OBJECTPROPERTY(id, N'IsUserTable') = 1)
     drop table tmpPurchaseReg1
if exists (select * from dbo.sysobjects where id = object_id(N'[dbo].[tmpPurchaseReg2]') and OBJECTPROPERTY(id, N'IsUserTable') = 1)
     drop table tmpPurchaseReg2
SELECT T1.LineNum,T0.DocNum AS 'Document Number', T0.DocDate AS 'Posting Date', T0.CardCode AS 'Vendor Code',
       T0.CardName AS 'Vendor Name', T0.NumAtCard as 'Vendor Ref. No', T0.VatSum AS 'Total Tax', T0.DocTotal AS 'Document Total' ,
       T1.AcctCode AS 'Account Code',T1.LineTotal AS 'Basic Amount', T1.ItemCode AS 'Item No.', T1.Dscription AS 'Item/Service Description',
       T2.SuppCatNum, T1.INMPrice AS 'Item Cost', T1.Quantity AS 'Quantity',T3.ItmsGrpNam AS'ItemGroup'
into tmpPurchaseReg1
FROM [dbo].[OPCH] T0
      INNER JOIN [dbo].[PCH1] T1 ON T1.DocEntry = T0.DocEntry
      INNER JOIN [dbo].[OITM] T2 ON T1.ItemCode = T2.ItemCode
      INNER JOIN [dbo].[OITB] T3 ON T2.ItmsGrpCod = T3.ItmsGrpCod
      --WHERE T0.DocDate >= CONVERT(DATETIME, [%0], 112)   AND T0.DocDate <= CONVERT(DATETIME, [%1], 112)
     WHERE T0.DocDate >=@StartDate AND T0.DocDate <=@EndDate
ORDER BY T0.DocNum
select * into tmpPurchaseReg2 from tmpPurchaseReg1
declare @Total int
declare @TmpCardCode varchar(200)
declare @DocNum int
declare PurchseRegister_Cursor cursor LOCAL for
     select [Document Number] from tmpPurchaseReg1 group by [Document Number] having count([Document Number]) > 1 order by [Document Number]
open PurchseRegister_Cursor
                        fetch next from PurchseRegister_Cursor into @DocNum
                        while @@fetch_status = 0
                        begin
                                    begin
                            drop table tmpPurchaseRegTemp
                             select top 1 * into tmpPurchaseRegTemp from tmpPurchaseReg2 where [Document Number] = @DocNum
                         select @TmpCardCode =[LineNum] from tmpPurchaseRegTemp
                         update tmpPurchaseReg2 set [Vendor Name] = '',[Total Tax] = 0,[Document Total] = 0
                                               where [Document Number] = @DocNum and [LineNum] <> @TmpCardCode
                                    end
                                   fetch next from PurchseRegister_Cursor into @DocNum
                        end
close PurchseRegister_Cursor
deallocate PurchseRegister_Cursor
BR
Samir Gandhi

HT4061 The screen of my iphone turned to blue and then shutted down. And it couldn't power on for few days.

The screen of my iphone turned to blue and then shutted down. And it couldn't power on for few days.

Try this First... No Data will be Lost..
Press and Hold the Sleep/Wake Button and the Home Button at the Same Time...
Wait for the Apple logo to Appear...
Usually takes about 15 - 20 Seconds... ( But can take Longer...)
Release the Buttons...
More > Frozen or unresponsive iPhone

Error " Data missing for the entry check while creating a new waste code

Hi all, While setting a new Waste code I get the error " Data missing for the entry check, correction:". while filling the NAM- WASTECOCAT - LER item.
This sould look for the catalog's name included in the phrase set but for some reason it doesn't find it giving me this error.
I am changing original Characteristics, phrase set, classes, and value assignment type. Just to have my own estructure with Znames for all of them.
I have also change the enviroment parameter "WAM_PHRSET_WACATLG" with the name of my phrase set.
I have checked everything several times watching for typos or looking for a missing step.
I have even tried including my new Z's characteristics in the classe and living the original SAP_EHS_1024_001_WASTE_CATALOG. (changing the enviroment parameter WAM_PHRSET_WACATLG to SAP_EHS_1024_001_WASTE_CATALOG) and it works.
I will like to change this characteristic by Z_EHS_WA_WASTE_CATALOG
Phrase set to Z_EHS_WA_WASTE_CATALOG.
enviroment parameter WAM_PHRSET_WACATLG= Z_EHS_WA_WASTE_CATALOG
After matching up the master data It should work fine but I might be missing something to get it running ok.
¿Any idea?
Regards,
Alvaro

Hello Juan Carlos, the value and class that I want to duplicate and doesn't work is for Waste Code, I have also duplicated the one you have displayed (waste pproperties) without any problem.
1.I have duplicated and changed class SAP_EHS_1024_001. to Z_EHS_WA
2. Create a copy of the 5 characteristics included in this class.
SAP_EHS_1024_001_WASTE_CATALOG
SAP_EHS_1024_001_WASTE_CODE
SAP_EHS_1024_001_WA_SUBCATEG
SAP_EHS_1024_001_WA_CATEGORY
SAP_EHS_1024_001_REMARK
change the name by
Z_EHS_WA_WASTE_CATALOG
Z_EHS_WA_WASTE_CODE
Z_EHS_WA_SUBCATEG
Z_EHS_WA_CATEGORY
Z_EHS_WA_REMARK.
I checked the funcion C14K_WASTECATLG_CHECK is in the value of the Z_EHS_WA_WASTE_CODE characteristic
I checked the funcion C14K_WASTECODE_CHECK is in the value of the Z_EHS_WA_WASTE_CATALOG characteristic
3. Create phrase sets for each new category. with same name.
4. Match up the master data.
5. Change the enviroment parameter.to Z_EHS_WA_WASTE_CATALOG
I think I have followed all the steps, but for some reason it doesn't find the catalog
The phrase for the catalog is EWC in english and LER in spanish.
Regards
Alvaro.

ABAP Program gives error after running successfully for few days / months

I have a problem that sometimes my programs start giving errors or does not run at all after successfully running for few days / months.
But, when I copy the same program with a different name (without any changes ) it starts running again.
Yesterday I had another problem. I was sending a request to be transported to Production Client, and the request was not getting transported. But when I changed just the name of the program, It was transported to Production Client.
I can't understand where the problem lies and what happens to the programs after running successfully for few days. All I have to do is just copy that programm into another name and it starts running.
Can anyone help me?
Regards,
SK Daniel

about the transport thing..i had the same problem few months back the reason was, i included a table which is having different package from my program..so wot im thinking is when you creating a different program u might be assigning different package to this new program and this package is same as all the tables included in your program...
regards

I have new iphone 5s(locked) which is taken in San jose, Now i am moving to India for few days , how to use my phone over there

i have new iphone 5s(locked) which is taken in San jose, Now i am moving to India for few days , how to use my phone over there

Contact your carrier and if your phone is locked then you need to use international roaming to be able to use your phone in India.

My 2nd iPod 4G Doesn't Work For Few Days

Hello.
I come here because I've got a probleme with my iPod 4G for few days now.
It's my second iPod of this generation because another that I had have bugued.
Now I explain my problem :
- First Last week my iPod started to have very high latency.
- Then I tried to play a song and my iPod blocked and display a icon of a "sad iPod".
- Finally now, It boot but after display the apple it's displaying directely icon of "Sad iPod".
So I can't connect it to my computer because like it can't boot, the computer can't synchronize it.
So I can't restore it like it's mentionned on the website.
My computer is a PC : Windows Xp Pro and I've never had a problem with my iPod 3G I don't understand...
I'm desesperate without my music :'(
Somebody can help me please ? I need your help ! Thanks.
PS : Sorry if my english is not very good but I'm french and I learn it for 3 years now so ...

Have a read through this post.
http://discussions.apple.com/message.jspa?messageID=2369954#2369954

Can you use Sync data from a few days ago?

I was reinstalling Firefox 10, did the whole back up thing, and when i was importing my bookmarks, I accidentally overwrote it instead. So i don't have the bookmarks anymore, and I turned to the sync function, but seeing as I have never used the sync function before, I overwrote that as well. So my question is if there is a way to get sync data from a few days ago?

Printers do not normally have any memory of previous print jobs; the exception is that some more expensive models (but not yours) are fitted with hard disks which can, in some circumstances, retain certain print jobs.
The Windows spooler can be set to retain copies of print jobs, but as this is not the default situation, it is unlikely that your jobs will have been retained.

Few days back I installed Autocad 2014 in my macbook pro 15" early 2012.For few days it worked fine but since last two days I'm getting graphical lag in my mac. Finger gestures and dock movement all seems to be lagging badly.Please help.I'm using maverick

Few days back I installed Autocad 2014 in my macbook pro 15" early 2012.For few days it worked fine but since last two days I'm getting graphical lag in my mac. Finger gestures and dock movement all seems to be lagging badly.Please help.I'm using mavericks

We regularly use Cocktail by Maintain software. You run the whole gamut of options but the important one is in System - Databases - Rebuild launch services. Also in Files - Caches - then clear the lot.
This is just houskeeping really but there are so many 'links' in A/cad it needs 'cleaning'

My Mac Book Pro 13 inch shuts down when I insert some usb on port. It will be dead for few days (no power, can't charge as well, no restarting) and after few days it will work? Any one facing same issue and any solutions please...

My Mac Book Pro 13 inch shuts down when I insert some usb on port. It will be dead for few days (no power, can't charge as well, no restarting) and after few days it will work? Any one facing same issue and any solutions please...

Hi ohmghimire,
Thanks for visiting Apple Support Communities.
If you're seeing unexpected behavior when using USB devices, try resetting the SMC on your MacBook Pro:
Resetting the SMC on portables with a battery you should not remove on your own
Note: Portable computers that have a battery you should not remove on your own include MacBook Pro (Early 2009) and later, all models of MacBook Air, and MacBook (Late 2009).
Shut down the computer.
Plug in the MagSafe power adapter to a power source, connecting it to the Mac if its not already connected.
On the built-in keyboard, press the (left side) Shift-Control-Option keys and the power button at the same time.
Release all the keys and the power button at the same time.
Press the power button to turn on the computer.
Note: The LED on the MagSafe power adapter may change states or temporarily turn off when you reset the SMC.
You can find the article with these steps here:
Intel-based Macs: Resetting the System Management Controller (SMC)
http://support.apple.com/kb/HT3964
If you still see this behavior after resetting the SMC, or your computer won't turn on, try the steps in this article next:
Troubleshooting: My computer won't turn on
http://support.apple.com/kb/ts1367
Best Regards,
Jeremy

E2E WA: Data missing for some tabs

Hi,
We have configured solution manager (4.0) ABAP stack to collect data from its own Solution Manager Diagnostics. Under the Workload Analysis the data is showing for some of the tabs like WorkProcess, Short dumps, User Load etc but some of the tabs like Top Dialog, Top Batch are not showing any data.
Any clues ?
Thanks
Murali.

Hi,
Thanks for the reply. If the system is up and running and if ST03n is showing a Top Dialog or Batch out of whatever it ran for that day or week will not that be enough to show in the SMD screen ? Is there anything else to be looked into specially for Top Dialog or Batch kind of classification ?
Thanks,
Murali.

Data missing for plant

Data is missing for a certain plant in spare parts infocube (BW). Please suggest me any reasons why this can happen.
Thanks.

Hi anand,
Check the data in PSA.
If you have the entries there for the missing plants then
Check the transfer structure whether any routines is used or not.(check plant info object also other info objects whether it has any routines or not) then check in the update rules whether there is any start routine defined , also check the fields in the update rules for availability of routines.
Also in the monitor screen drill down the data packages right click on any package and simulate update , select all records for simulation and then simulate it and check.
Regards
RaM

ESS - Create Expense Report Link is missing for few users

Hi,
We are on ECC 6.0 Ehp 3 with EP 7.0.
We are using the ESS and in that Standard SAP provided Travel and Expenses Module.
For few of the users, the Create Expense Report link is missing eventhough the user is assigned with the Traveller Role
SAP_FI_TV_TRAVELER
Request you to let me know if any setting needs to be done in the back end/infotype to make the Create Expense Report link visible in the portal.
Appreciate your help.
Thanks and Regards,
Sekar

Hello,
Same happened on our side. User is already set with the proper roles, with the correct info types but when logging in the Portal- she, too, could not view the link for Create Expense Report (which is supposed to Create an expense report for a trip without a travel plan).
When i use my userid, and just switch personnel number to her number, I could create an expense report on her behalf.
That made me conclude that her traveller roles are fine.
Pls help.

ST03n Data missing for few days

Similar Messages

Maybe you are looking for