Stalls at "Starting Windows....." during installation
I've tried to run Bootcamp a couple times now, and each time, I have encountered the same problem. I am able to partition the drive and begin the installation through Bootcamp Assistant, and I'm able to get windows loaded up to a point. During the blue installation screen when it says "Starting windows......" at the bottom of the screen, it stalls out. There's no response to the keyboard, and the only way for me to reboot is to go with the mouse button eject for the windows install disk in the drive. Again, I've tried this a couple times now, and I'm guessing that I'm missing something simple.....
Also, the Windows is XP home edition SP2.
Any thoughts?
Thanks for the help!
When I went through the installation process I got slightly farther than you did. It stalled out when I got to the screen that gave you three choices, one of which was to hit "Enter" to start the installation process. At this point my keyboard was non-responsive. (I actually had an additional problem before this point.)
I solved my problems by:
1. Using Disk Utility to make a disk image of my Windows XP SP2 install DVD and then burning this image onto a new DVD. (My drive didn't like the hologram on the Windows disk.)
2. Using a Windows keyboard. (Once I finished the Windows installation and installed the Mac drivers using the Leopard Mac install DVD, I could go back to using my Apple keyboard. However, I have to plug the mouse into the USB port on the computer because the mouse won't work if the mouse is plugged plugged into the USB port on the Apple keyboard.)
Maybe that will help you.
Similar Messages
-
[Solved]Can't get past "Starting network" during installation from USB
I'm trying to do a fresh install of Archlinux on my laptop, following the Beginners Guide. However, I never get to the shell prompt because the installation gets stuck at "Starting network [Busy]".
These are steps I followed:
- I downloaded the latest Arch ISO.
- I wrote it to a usb stick ("Kingston Data Traveler") with "dd if=archlinux.iso of=/dev/sdb"
- I put the usb stick into my laptop (HP Pavilion dm1-4139sd), and booted it. I chose "x86_64". Everything seems to go fine, the only warning I get is: "microcode: failed to load file amd-ucode/microcode_amd.bin".
- I get the message "INIT: Entering runlevel: 3" and "Starting Syslog-NG [Done]", after that its endlessly (at least 20 minutes) stuck on "Starting network [Busy]".
I tried the following variations on the above:
- Wrote the ISO to a different USB, samen problem.
- Tried it with a different Arch version (from August), same problem.
- Turned kvm on and off, same problem.
- Pressed TAB at the "x86_64" line and added "acpi=off" to the end of it. I then get:
:: Triggering uevents....
[ 19.697932 ] usb 1-1: device not accepting address 2, error -110
:: Mounting '/dev/disk/by-label/ARCH_201209' to '/run/archiso/bootmnt'
Waiting 30 seconds for device /dev/disk/by-label/ARCH_201209
[ 35.312165 ] usb 1-1: device not accepting address 3, error -110
[ 45.821422 ] usb 1-1: device not accepting address 4, error -110
[ 56.330681 ] usb 1-1: device not accepting address 5, error -110
[ 56.330681 ] hub 1-0:1.0: unable to enumerate USB devices on port 1
ERROR: '/dev/disk/by-label/ARCH_201209' device did not show up after 30 seconds....
Falling back to interactive prompt
You can try to fix the problem manually, log out when you are finished
sh: can't access tty; job control turned off
[rootfs /]#
I'm not sure what to do in this prompt. At least the network isn't working and none of the normal commands.
- I reset the DHCP leases on my modem, same problem.
- I turned off/on the hardware WLAN, same problem.
- I tried it with or without the LAN cable plugged in, same problem.
- I tried it with or without the battery plugged in, and with or without the power cable plugged in. Same problem.
I also performed the Arch memory test, and the bios hard disk test. They both report no errors.
I did an Arch installation a month ago on this laptop, and back then it didn't have this problem. I still have that arch installed from back then and it boots/works without problem (I have Starting NetworkingManager [Done]). I know I technically don't need to install arch again, as I still have the old one, but I wanted to clean the changes I made to some settings files and I if it turns out this is some kind of hardware problem I'd like to return it to the store.
Please help! I'm not really that familiar with Linux in general, so it might have been a very basic mistake from me as well. I have no idea what to do next, except for formatting my harddisk (which I don't think should influence the installer?), or trying to install a different Linux distro.
Edit: The solution that solved this problem for me in the end was resetting the BIOS to its defaults.
Last edited by dbakker (2012-09-15 11:28:14)DSpider wrote:Did you check the MD5 checksum? If you downloaded it using a BitTorrent client, then you don't need to (its hash is checked during downloading).
Yes, I downloaded it using BitTorrent and the MD5 matches.
DSpider wrote:Try a different stick?
Yes, I tried it with 2 different USB sticks. They are both from the same brand ("Kingston DataTraveler"), so I might try different brands as well, but I don't think it is the problem.
DSpider wrote:Or at least a different method from that wiki page. For example, "dd"-ing it should work just fine.
The methods for writing the ISO that I tried so far:
The base method:
dd if=archlinux.iso of=/dev/sdb
(from an Arch install)
The method without overwriting your USB drive (created a FAT32 drive with an VFAT filesystem, from an arch install)
Using Imagewriter (from Windows)
Each method gives the same result: the laptop gets stuck at "Starting network [Busy]" when booted from one of the USB sticks. My modem indicates that it "sees" the laptop, but that the laptop has no established connection. When the laptop is stuck at the "Starting network [Busy]", all the activity on the USB stick stops (the light stops flashing).
The thing I find most strange is that the OS currently installed on the laptop has no problems booting or accessing the internet (both wired and wireless) at all. -
I got an "Apple mobile Device' failed to start error during installation and itunes won't install.
For some reason I got an error message trying to update itunes on my Vista PC and for some reason could not run itunes. I uninstalled itunes completely and tried to download a new installation. Near the end of the installation I got this error message. "Service 'Apple Mobile Device' (Apple Mobile Device) failed to start. Verify that you have sufficient privileges to start system services." I was given the choices of 'cancel', 'retry', and 'abort'. I tried 'retry' and got the same error again. I tried 'abort' and the installation eventually ended in another error and suggested that I reinstall itunes. I was in the administrator's account when I attempted all these things.Has anyone had a similar problem or knows how to get the installation completed?? Thanks for any help.
Hello smittylin,
The following articles provides steps that can help get iTunes back up and running.
How to restart the Apple Mobile Device Service (AMDS) on Windows
http://support.apple.com/kb/TS1567
iTunes 11.1.4 for Windows: Unable to install or open
http://support.apple.com/kb/TS5376
Cheers,
Allen -
Cannot start Windows Server installation
Hi,
I want to upgrade my Server 2008 R2 to Server 2012 R2. But everytime I start the setup in Windows for an in-place upgrade, an error message pops-up saying "Windows Setup experienced an unexpected error. To install Windows, restart the
installation.", right after the "Setup is starting..." stage.
This doesn't have to do with the media or drive. I tried with a virtual drive, and still the same. It doesn't have to do with the image as well, the same error appears if I try to start a Server 2008 R2 installation or any other Windows installation.
The OS hard disk is a dynamic hard disk.
Here is the log from Setup.act:
2013-12-21 03:24:09, Info IBS InstallWindows:Successfully loaded resource language [en-US]
2013-12-21 03:24:09, Info [0x0601c1] IBS InstallWindows:Install Path = C:\$WINDOWS.~BT\Sources
2013-12-21 03:24:09, Info [0x0601c2] IBS InstallWindows:Setup Phase = 1
2013-12-21 03:24:09, Info [0x0606cc] IBS LogBootDeviceInfo:The firmware boot device ARC path is [multi(0)disk(0)rdisk(0)partition(1)] and NT path is [\Device\Harddisk1\Partition1].
2013-12-21 03:24:09, Info [0x0606cc] IBS LogBootDeviceInfo:The system boot device ARC path is [multi(0)disk(0)rdisk(0)partition(2)] and NT path is [\Device\Harddisk1\Partition2].
2013-12-21 03:24:09, Info [0x0601c3] IBS InstallWindows:Starting downlevel phase of Setup.
2013-12-21 03:24:09, Info [0x0601c5] IBS InstallWindows:Setting Working directory as C:\$WINDOWS.~BT\Sources\Panther
2013-12-21 03:24:09, Info [0x0601ce] IBS Setup has started phase 1 at 2013-12-21 03:24:09
2013-12-21 03:24:09, Info [0x0601cf] IBS Install source is C:\$WINDOWS.~BT\Sources
2013-12-21 03:24:09, Info [0x0601d0] IBS Build version is 6.2.9200.16384 (win8_rtm.120725-1247)
2013-12-21 03:24:09, Info [0x06403d] IBSLIB CreateSetupBlackboard:Creating a new persistent blackboard. Path is [C:\$WINDOWS.~BT\Sources\Panther\SetupInfo] Setup phase is [1]
2013-12-21 03:24:09, Info [0x090008] PANTHR CBlackboard::Open: C:\$WINDOWS.~BT\Sources\Panther\SetupInfo succeeded.
2013-12-21 03:24:09, Info [0x064043] IBSLIB CreateSetupBlackboard:Successfully created/opened Setup black board path is [C:\$WINDOWS.~BT\Sources\Panther\SetupInfo]
2013-12-21 03:24:09, Info IBS InstallWindows:No UI language from a previous boot was found on the blackboard. Using selected language [en-US].
2013-12-21 03:24:09, Info IBS InstallWindows:Setup architecture is [x64]
2013-12-21 03:24:09, Info SetupSetVolume: Marking [C:\] for tracking as [TildeBTVolume]
2013-12-21 03:24:09, Info IBSLIB SetBTVolumePaths: BTSources folder path = [C:\$WINDOWS.~BT\Sources]
2013-12-21 03:24:09, Info [0x0606cc] IBS GetSystemPartitionNTPath: Found system partition at [\Device\Harddisk1\Partition1].
2013-12-21 03:24:09, Warning [0x0606cc] IBS GetSystemPartitionPath: Unable to find DOS drive path for system partition [\Device\Harddisk1\Partition1].
2013-12-21 03:24:09, Info IBSLIB SetSystemVolumePath:Could not find DOS path for system partition; looking for NT path...
2013-12-21 03:24:09, Info [0x0606cc] IBS GetSystemPartitionNTPath: Found system partition at [\Device\Harddisk1\Partition1].
2013-12-21 03:24:09, Info IBSLIB SetSystemVolumePath:Found NT path for system partition: \Device\Harddisk1\Partition1; assigning temporary drive letter...
2013-12-21 03:24:09, Error [0x0601d3] IBS
InstallWindows:SetSetupBBProperties failed.[gle=0x00000002]
2013-12-21 03:24:19, Info [0x090009] PANTHR CBlackboard::Close: c:\$windows.~bt\sources\panther\setupinfo.
Any thoughts about this issue?
Thanks in advance!2013-12-21 03:24:09, Info IBSLIB SetSystemVolumePath:Found NT path for system partition: \Device\Harddisk1\Partition1;
assigning temporary drive letter...
2013-12-21 03:24:09, Error [0x0601d3] IBS
InstallWindows:SetSetupBBProperties failed.[gle=0x00000002]
assigning temporary drive letter...
I think the HDD has only 1 partition and Windows could not extract into another partition so, it hasn't reach the point where it can roll back -
Error while starting OMS during installation of Enterprise Manager12c
Hello Guys,
I am trying to install Oracle Enterprise Manager 12c(64bit) on OEL5.2(64bit), but after successfully going through all
the per-requisites of the installation; the installation fails at 89% "Start Oracle Management Service" phase and
at "Agent Configuration Assistant" phase.
Error is "Error Starting server EMGC_OMS1: weblogic.nodemanager.NMException: Exception while starting server 'EMGC_OMS1'"
Tried to resolve the certificate issue in the log following the MOS [ID 1320530.1] - Ignoring the trusted CA certificate warnings when connecting to Node Manager using WLST nmConnect() but the command keytool failed with java exception.
I am using two VMs for the setup:-
Oracle Management Repository :=
Server Name = OEM12c-OMR-01.example.com
Operating system = OEL5.5(64bit)
Database = Oracle Database 11g Enterprise (64bit)
Database SID = OMR
Ram = 8 GB
HDD = 100 GB
Oracle Management Repository :=
Server Name = OEM12c-OMS-01.example.com
Operating system = OEL5.2(64bit)
Ram = 8 GB
HDD = 100 GB
OEM Installer log:=
INFO: oracle.sysman.top.oms:BaseConfiguration:invoke:Starting BaseConfiguration invoke method on an aggregate=oracle.sysman.top.oms for Action=configuration in step=9:microstep=0
INFO: oracle.sysman.top.oms:Fetcing ports from teh static ports file: /home/oracle/software/oracle/middleware/.gcinstall_temp/staticports.ini
INFO: oracle.sysman.top.oms:Starting OMS ...
INFO: oracle.sysman.top.oms:Executing command: /home/oracle/software/oracle/middleware/oms/bin/emctl start oms
INFO: oracle.sysman.top.oms:Oracle Enterprise Manager Cloud Control 12c Release 12.1.0.1.0
INFO: oracle.sysman.top.oms:Copyright (c) 1996, 2012 Oracle Corporation. All rights reserved.
INFO: oracle.sysman.top.oms:Starting WebTier...
INFO: oracle.sysman.top.oms:WebTier Successfully Started
INFO: oracle.sysman.top.oms:Starting Oracle Management Server...
INFO: oracle.sysman.top.oms:Oracle Management Server Could Not Be Started
INFO: oracle.sysman.top.oms:Oracle Management Server is Down
INFO: oracle.sysman.top.oms:Please check /home/oracle/software/oracle/middleware/gc_inst/em/EMGC_OMS1/sysman/log/emctl.log for error details
SEVERE: oracle.sysman.top.oms:Starting of OMS failed.
INFO: oracle.sysman.top.oms:The plug-in Start Oracle Management Service has failed its optional perform method
INFO: oracle.sysman.top.oms:About to execute plug-in Start Oracle Management Service
INFO: oracle.sysman.top.oms:The plug-in Start Oracle Management Service is running
INFO: oracle.sysman.top.oms:Internal PlugIn Class: oracle.sysman.oms.StartOMS
INFO: oracle.sysman.top.oms:Classpath = /home/oracle/software/oracle/middleware/oms/sysman/jlib/omsConfig.jar:/home/oracle/software/oracle/middleware/oms/jdbc/lib/ojdbc6.jar:/home/oracle/software/oracle/middleware/oms/sysman/jlib/emcore_client.jar:/home/oracle/software/oracle/middleware/oms/../modules/com.bea.core.apache.log4j_1.2.13.jar:/home/oracle/software/oracle/middleware/oms/jlib/rcucommon.jar:/home/oracle/software/oracle/middleware/oms/jdbc/lib/ojdbc6.jar:/home/oracle/software/oracle/middleware/oms/sysman/jlib/emagentSDK.jar:/home/oracle/software/oracle/middleware/oms/../oracle_common/modules/oracle.xdk_11.1.0/xmlparserv2.jar:/home/oracle/software/oracle/middleware/oms/../oracle_common/modules/oracle.odl_11.1.1/ojdl.jar:/home/oracle/software/oracle/middleware/oms/../oracle_common/modules/oracle.xdk_11.1.0/xml.jar:/home/oracle/software/oracle/middleware/oms/../oracle_common/modules/oracle.jdbc_11.1.1/ojdbc6dms.jar:/home/oracle/software/oracle/middleware/oms/../oracle_common/modules/oracle.dms_11.1.1/dms.jar:/home/oracle/software/oracle/middleware/oms/../oracle_common/modules/oracle.odl_11.1.1/ojdl.jar:/home/oracle/software/oracle/middleware/oms/jlib/rcu.jar
INFO: oracle.sysman.top.oms:BaseConfiguration:invoke:Starting BaseConfiguration invoke method on an aggregate=oracle.sysman.top.oms for Action=configuration in step=9:microstep=0
INFO: oracle.sysman.top.oms:Fetcing ports from teh static ports file: /home/oracle/software/oracle/middleware/.gcinstall_temp/staticports.ini
INFO: oracle.sysman.top.oms:Starting OMS ...
INFO: oracle.sysman.top.oms:Executing command: /home/oracle/software/oracle/middleware/oms/bin/emctl start oms
INFO: oracle.sysman.top.oms:Oracle Enterprise Manager Cloud Control 12c Release 12.1.0.1.0
INFO: oracle.sysman.top.oms:Copyright (c) 1996, 2012 Oracle Corporation. All rights reserved.
INFO: oracle.sysman.top.oms:Starting WebTier...
INFO: oracle.sysman.top.oms:WebTier Successfully Started
INFO: oracle.sysman.top.oms:Starting Oracle Management Server...
INFO: oracle.sysman.top.oms:Oracle Management Server Could Not Be Started
INFO: oracle.sysman.top.oms:Oracle Management Server is Down
INFO: oracle.sysman.top.oms:Please check /home/oracle/software/oracle/middleware/gc_inst/em/EMGC_OMS1/sysman/log/emctl.log for error details
SEVERE: oracle.sysman.top.oms:Starting of OMS failed.
INFO: oracle.sysman.top.oms:The plug-in Start Oracle Management Service has failed its optional perform method
/home/oracle/software/oracle/middleware/gc_inst/em/EMGC_OMS1/sysman/log/emctl.log :=
2012-06-03 21:19:28,986 [main] DEBUG wls.OMSController main.199 - Log location is /home/oracle/software/oracle/middleware/gc_inst/em/EMGC_OMS1/sysman/log/emctl.log
2012-06-03 21:19:28,989 [main] INFO wls.OMSController startOMS.828 - admin start is false
2012-06-03 21:19:28,989 [main] INFO wls.OMSController startOMS.829 - is service is false
2012-06-03 21:19:29,005 [main] INFO wls.OMSController getEnvProps.476 - Setting trust store system properties: -Dweblogic.security.TrustKeyStore=DemoTrust -Dweblogic.security.SSL.ignoreHostnameVerification=true -Djava.security.egd=file:///dev/./urandom
2012-06-03 21:19:29,006 [main] INFO wls.OMSController startOMS.848 - Starting WebTier...
2012-06-03 21:19:29,010 [main] INFO util.WebTierUtil execCmd.407 - Running the command: /home/oracle/software/oracle/middleware/gc_inst/WebTierIH1/bin/opmnctl stopall
2012-06-03 21:19:34,028 [main] INFO util.WebTierUtil getProcessResult.467 - opmnctl cmd output: opmnctl stopall: stopping opmn and all managed processes...
2012-06-03 21:19:34,029 [main] INFO util.WebTierUtil getProcessResult.475 - opmnctl cmd error:
2012-06-03 21:19:34,029 [main] INFO util.WebTierUtil getProcessResult.479 - opmnctl cmd exited with code 0
2012-06-03 21:19:34,030 [main] INFO util.WebTierUtil execCmd.407 - Running the command: /home/oracle/software/oracle/middleware/gc_inst/WebTierIH1/bin/opmnctl startall
2012-06-03 21:19:40,300 [main] INFO util.WebTierUtil getProcessResult.467 - opmnctl cmd output: opmnctl startall: starting opmn and all managed processes...
2012-06-03 21:19:40,301 [main] INFO util.WebTierUtil getProcessResult.475 - opmnctl cmd error:
2012-06-03 21:19:40,301 [main] INFO util.WebTierUtil getProcessResult.479 - opmnctl cmd exited with code 0
2012-06-03 21:19:40,302 [main] INFO wls.OMSController startOMS.859 - WebTier Successfully Started
2012-06-03 21:19:40,302 [main] INFO wls.OMSController startOMS.886 - wlst command is /home/oracle/software/oracle/middleware/oracle_common/common/bin/wlst.sh /home/oracle/software/oracle/middleware/oms/bin/startOMS.py
2012-06-03 21:19:40,302 [main] INFO wls.OMSController startOMS.887 - Executing the wlst command for startOMS...
2012-06-03 21:19:40,303 [main] INFO wls.OMSController startOMS.891 - optional admin start is false
2012-06-03 21:19:40,303 [main] INFO wls.OMSController startOMS.892 - optional pbsonly start is false
2012-06-03 21:19:40,353 [Thread-1] INFO wls.OMSController run.1744 - <OUT>CLASSPATH=/home/oracle/software/oracle/middleware/patch_wls1035/profiles/default/sys_manifest_classpath/weblogic_patch.jar:/home/oracle/software/oracle/middleware/jdk16/jdk/lib/tools.jar:/home/oracle/software/oracle/middleware/wlserver_10.3/server/lib/weblogic_sp.jar:/home/oracle/software/oracle/middleware/wlserver_10.3/server/lib/weblogic.jar:/home/oracle/software/oracle/middleware/modules/features/weblogic.server.modules_10.3.5.0.jar:/home/oracle/software/oracle/middleware/wlserver_10.3/server/lib/webservices.jar:/home/oracle/software/oracle/middleware/modules/org.apache.ant_1.7.1/lib/ant-all.jar:/home/oracle/software/oracle/middleware/modules/net.sf.antcontrib_1.1.0.0_1-0b2/lib/ant-contrib.jar:/home/oracle/software/oracle/middleware/patch_wls1035/profiles/default/sys_manifest_classpath/weblogic_patch.jar:/home/oracle/software/oracle/middleware/jdk16/jdk/lib/tools.jar:/home/oracle/software/oracle/middleware/wlserver_10.3/server/lib/weblogic_sp.jar:/home/oracle/software/oracle/middleware/wlserver_10.3/server/lib/weblogic.jar:/home/oracle/software/oracle/middleware/modules/features/weblogic.server.modules_10.3.5.0.jar:/home/oracle/software/oracle/middleware/wlserver_10.3/server/lib/webservices.jar:/home/oracle/software/oracle/middleware/modules//wlst/resources/igfwlsthelp.jar:/home/oracle/software/oracle/middleware/oracle_common/common/wlst/resources/jps-wlst.jar:/home/oracle/software/oracle/middleware/oracle_common/common/wlst/resources/jrf-wlst.jar:/home/oracle/software/oracle/middleware/oracle_common/common/wlst/resources/oamap_help.jar:/home/oracle/software/oracle/middleware/oracle_common/common/wlst/resources/oamAuthnProvider.jar:/home/oracle/software/oracle/middleware/oracle_common/common/wlst/resources/ossoiap_help.jar:/home/oracle/software/oracle/middleware/oracle_common/common/wlst/resources/ossoiap.jar:/home/oracle/software/oracle/middleware/oracle_common/common/wlst/resources/ovdwlsthelp.jar:/home/oracle/software/oracle/middleware/oracle_common/common/wlst/resources/sslconfigwlst.jar:/home/oracle/software/oracle/middleware/oracle_common/common/wlst/resources/wsm-wlst.jar
2012-06-03 21:19:40,354 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:19:40,354 [Thread-1] INFO wls.OMSController run.1744 - <OUT>PATH=/home/oracle/software/oracle/middleware/wlserver_10.3/server/bin:/home/oracle/software/oracle/middleware/modules/org.apache.ant_1.7.1/bin:/home/oracle/software/oracle/middleware/jdk16/jdk/jre/bin:/home/oracle/software/oracle/middleware/jdk16/jdk/bin:/home/oracle/software/oracle/middleware/oms/bin:/home/oracle/software/oracle/middleware/oms/jdk/bin:/home/oracle/software/oracle/middleware/oms/perl/bin:/home/oracle/software/oracle/middleware/wlserver_10.3/server/bin:/home/oracle/software/oracle/middleware/modules/org.apache.ant_1.7.1/bin:/home/oracle/software/oracle/middleware/jdk16/jdk/jre/bin:/home/oracle/software/oracle/middleware/jdk16/jdk/bin:/usr/bin:/usr/ccs/bin:/usr/bin:/usr/ccs/bin:/usr/kerberos/bin:/usr/local/bin:/bin:/usr/bin:/home/oracle/bin:/OEM12c/install:/OEM12c/install:/bin:/usr/bin
2012-06-03 21:19:40,354 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:19:40,355 [Thread-1] INFO wls.OMSController run.1744 - <OUT>Your environment has been set.
2012-06-03 21:19:40,355 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:19:40,356 [Thread-1] INFO wls.OMSController run.1744 - <OUT>CLASSPATH=/home/oracle/software/oracle/middleware/patch_wls1035/profiles/default/sys_manifest_classpath/weblogic_patch.jar:/home/oracle/software/oracle/middleware/jdk16/jdk/lib/tools.jar:/home/oracle/software/oracle/middleware/wlserver_10.3/server/lib/weblogic_sp.jar:/home/oracle/software/oracle/middleware/wlserver_10.3/server/lib/weblogic.jar:/home/oracle/software/oracle/middleware/modules/features/weblogic.server.modules_10.3.5.0.jar:/home/oracle/software/oracle/middleware/wlserver_10.3/server/lib/webservices.jar:/home/oracle/software/oracle/middleware/modules/org.apache.ant_1.7.1/lib/ant-all.jar:/home/oracle/software/oracle/middleware/modules/net.sf.antcontrib_1.1.0.0_1-0b2/lib/ant-contrib.jar:/home/oracle/software/oracle/middlewarehe.ant_1.7.1/lib/ant-all.jar:/home/oracle/software/oracle/middleware/modules/net.sf.antcontrib_1.1.0.0_1-0b2/lib/ant-contrib.jar:/home/oracle/software/oracle/middleware/oms/sysman/jlib/emagentSDK.jar:/home/oracle/software/oracle/middleware/oms/sysman/jlib/emCORE.jar:/home/oracle/software/oracle/middleware/oracle_common/modules/oracle.http_client_11.1.1.jar:/home/oracle/software/oracle/middleware/oracle_common/modules/oracle.pki_11.1.1/oraclepki.jar:/home/oracle/software/oracle/middlewarerces/ossoiap_help.jar:/home/oracle/software/oracle/middleware/oracle_common/common/wlst/resources/ossoiap.jar:/home/oracle/software/oracle/middleware/oracle_common/common/wlst/resources/ovdwlsthelp.jar:/home/oracle/software/oracle/middleware/oracle_common/common/wlst/resources/sslconfigwlst.jar:/home/oracle/software/oracle/middleware/oracle_common/common/wlst/resources/wsm-wlst.jar:/home/oracle/software/oracle/middleware/utils/config/10.3/config-launch.jar::/home/oracle/software/oracle/middleware/wlserver_10.3/common/derby/lib/derbynet.jar:/home/oracle/software/oracle/middleware/wlserver_10.3/common/derby/lib/derbyclient.jar:/home/oracle/software/oracle/middleware/wlserver_10.3/common/derby/lib/derbytools.jar::
2012-06-03 21:19:41,231 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:19:41,232 [Thread-1] INFO wls.OMSController run.1744 - <OUT>Initializing WebLogic Scripting Tool (WLST) ...
2012-06-03 21:19:41,232 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:19:44,452 [Thread-1] INFO wls.OMSController run.1744 - <OUT>Welcome to WebLogic Server Administration Scripting Shell
2012-06-03 21:19:44,452 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:19:44,453 [Thread-1] INFO wls.OMSController run.1744 - <OUT>Type help() for help on available commands
2012-06-03 21:19:44,453 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:19:44,525 [Thread-1] INFO wls.OMSController run.1744 - <OUT>nm home is /home/oracle/software/oracle/middleware/gc_inst/NodeManager/emnodemanager
2012-06-03 21:19:44,527 [Thread-1] INFO wls.OMSController run.1744 - <OUT>is_admin_host is TRUE
2012-06-03 21:19:44,527 [Thread-1] INFO wls.OMSController run.1744 - <OUT>admin_start is FALSE
2012-06-03 21:19:44,528 [Thread-1] INFO wls.OMSController run.1744 - <OUT>admin_only_start is NONE
2012-06-03 21:19:44,958 [Thread-1] INFO wls.OMSController run.1744 - <OUT>Connecting to Node Manager ...
2012-06-03 21:19:45,127 [Thread-1] INFO wls.OMSController run.1744 - <OUT><Jun 3, 2012 9:19:45 PM IST> <Info> <Security> <BEA-090906> <Changing the default Random Number Generator in RSA CryptoJ from ECDRBG to FIPS186PRNG. To disable this change, specify -Dweblogic.security.allowCryptoJDefaultPRNG=true>
2012-06-03 21:19:46,368 [Thread-1] INFO wls.OMSController run.1744 - <OUT><Jun 3, 2012 9:19:46 PM IST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=Entrust Root Certification Authority - G2,OU=(c) 2009 Entrust\, Inc. - for authorized use only,OU=See www.entrust.net/legal-terms,O=Entrust\, Inc.,C=US". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
2012-06-03 21:19:46,376 [Thread-1] INFO wls.OMSController run.1744 - <OUT><Jun 3, 2012 9:19:46 PM IST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=thawte Primary Root CA - G3,OU=(c) 2008 thawte\, Inc. - For authorized use only,OU=Certification Services Division,O=thawte\, Inc.,C=US". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
2012-06-03 21:19:46,384 [Thread-1] INFO wls.OMSController run.1744 - <OUT><Jun 3, 2012 9:19:46 PM IST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=T-TeleSec GlobalRoot Class 3,OU=T-Systems Trust Center,O=T-Systems Enterprise Services GmbH,C=DE". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
2012-06-03 21:19:46,386 [Thread-1] INFO wls.OMSController run.1744 - <OUT><Jun 3, 2012 9:19:46 PM IST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=T-TeleSec GlobalRoot Class 2,OU=T-Systems Trust Center,O=T-Systems Enterprise Services GmbH,C=DE". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
2012-06-03 21:19:46,391 [Thread-1] INFO wls.OMSController run.1744 - <OUT><Jun 3, 2012 9:19:46 PM IST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=GlobalSign,O=GlobalSign,OU=GlobalSign Root CA - R3". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
2012-06-03 21:19:46,393 [Thread-1] INFO wls.OMSController run.1744 - <OUT><Jun 3, 2012 9:19:46 PM IST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "OU=Security Communication RootCA2,O=SECOM Trust Systems CO.\,LTD.,C=JP". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
2012-06-03 21:19:46,397 [Thread-1] INFO wls.OMSController run.1744 - <OUT><Jun 3, 2012 9:19:46 PM IST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=VeriSign Universal Root Certification Authority,OU=(c) 2008 VeriSign\, Inc. - For authorized use only,OU=VeriSign Trust Network,O=VeriSign\, Inc.,C=US". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
2012-06-03 21:19:46,412 [Thread-1] INFO wls.OMSController run.1744 - <OUT><Jun 3, 2012 9:19:46 PM IST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=KEYNECTIS ROOT CA,OU=ROOT,O=KEYNECTIS,C=FR". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
2012-06-03 21:19:46,417 [Thread-1] INFO wls.OMSController run.1744 - <OUT><Jun 3, 2012 9:19:46 PM IST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=GeoTrust Primary Certification Authority - G3,OU=(c) 2008 GeoTrust Inc. - For authorized use only,O=GeoTrust Inc.,C=US". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
2012-06-03 21:19:46,584 [Thread-1] INFO wls.OMSController run.1744 - <OUT>Successfully Connected to Node Manager.
2012-06-03 21:19:46,585 [Thread-1] INFO wls.OMSController run.1744 - <OUT>status of node manager:
2012-06-03 21:19:46,585 [Thread-1] INFO wls.OMSController run.1744 - <OUT>Currently connected to Node Manager to monitor the domain GCDomain.
2012-06-03 21:19:46,585 [Thread-1] INFO wls.OMSController run.1744 - <OUT>current status of EMGC_ADMINSERVER:
2012-06-03 21:19:46,586 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:19:46,586 [Thread-1] INFO wls.OMSController run.1744 - <OUT>RUNNING
2012-06-03 21:19:46,586 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:19:46,586 [Thread-1] INFO wls.OMSController run.1744 - <OUT>current status of EMGC_OMS1:
2012-06-03 21:19:46,587 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:19:46,587 [Thread-1] INFO wls.OMSController run.1744 - <OUT>FAILED_NOT_RESTARTABLE
2012-06-03 21:19:46,587 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:19:46,587 [Thread-1] INFO wls.OMSController run.1744 - <OUT>Starting server EMGC_OMS1
2012-06-03 21:19:46,587 [Thread-1] INFO wls.OMSController run.1744 - <OUT>Starting server EMGC_OMS1 ...
2012-06-03 21:37:51,702 [Thread-1] INFO wls.OMSController run.1744 - <OUT>Error Starting server EMGC_OMS1: weblogic.nodemanager.NMException: Exception while starting server 'EMGC_OMS1'
2012-06-03 21:37:51,702 [Thread-1] INFO wls.OMSController run.1744 - <OUT>new status of EMGC_OMS1:
2012-06-03 21:37:51,703 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:37:51,703 [Thread-1] INFO wls.OMSController run.1744 - <OUT>FAILED_NOT_RESTARTABLE
2012-06-03 21:37:51,704 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:37:51,704 [Thread-1] INFO wls.OMSController run.1744 - <OUT>wait until EMGC_OMS1 becomes RUNNING
2012-06-03 21:37:51,704 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:37:51,704 [Thread-1] INFO wls.OMSController run.1744 - <OUT>FAILED_NOT_RESTARTABLE
2012-06-03 21:37:51,705 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:37:51,705 [Thread-1] INFO wls.OMSController run.1744 - <OUT>sleep for 10 seconds...
2012-06-03 21:38:01,708 [Thread-1] INFO wls.OMSController run.1744 - <OUT>status of EMGC_OMS1:
2012-06-03 21:38:01,709 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:38:01,709 [Thread-1] INFO wls.OMSController run.1744 - <OUT>FAILED_NOT_RESTARTABLE
2012-06-03 21:38:01,709 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:38:01,709 [Thread-1] INFO wls.OMSController run.1744 - <OUT>sleep for 10 seconds...
2012-06-03 21:38:11,711 [Thread-1] INFO wls.OMSController run.1744 - <OUT>status of EMGC_OMS1:
2012-06-03 21:38:11,712 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:38:11,712 [Thread-1] INFO wls.OMSController run.1744 - <OUT>FAILED_NOT_RESTARTABLE
2012-06-03 21:38:11,712 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:38:11,713 [Thread-1] INFO wls.OMSController run.1744 - <OUT>sleep for 10 seconds...
2012-06-03 21:38:21,714 [Thread-1] INFO wls.OMSController run.1744 - <OUT>status of EMGC_OMS1:
2012-06-03 21:38:21,715 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:38:21,715 [Thread-1] INFO wls.OMSController run.1744 - <OUT>FAILED_NOT_RESTARTABLE
2012-06-03 21:38:21,715 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:38:21,715 [Thread-1] INFO wls.OMSController run.1744 - <OUT>sleep for 10 seconds...
2012-06-03 21:38:31,717 [Thread-1] INFO wls.OMSController run.1744 - <OUT>status of EMGC_OMS1:
2012-06-03 21:38:31,718 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:38:31,718 [Thread-1] INFO wls.OMSController run.1744 - <OUT>FAILED_NOT_RESTARTABLE
2012-06-03 21:38:31,718 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:38:31,718 [Thread-1] INFO wls.OMSController run.1744 - <OUT>sleep for 10 seconds...
2012-06-03 21:38:41,719 [Thread-1] INFO wls.OMSController run.1744 - <OUT>status of EMGC_OMS1:
2012-06-03 21:38:41,720 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:38:41,720 [Thread-1] INFO wls.OMSController run.1744 - <OUT>FAILED_NOT_RESTARTABLE
2012-06-03 21:38:41,720 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:38:41,720 [Thread-1] INFO wls.OMSController run.1744 - <OUT>sleep for 10 seconds...
2012-06-03 21:38:51,722 [Thread-1] INFO wls.OMSController run.1744 - <OUT>status of EMGC_OMS1:
2012-06-03 21:38:51,723 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:38:51,723 [Thread-1] INFO wls.OMSController run.1744 - <OUT>FAILED_NOT_RESTARTABLE
2012-06-03 21:38:51,724 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:38:51,724 [Thread-1] INFO wls.OMSController run.1744 - <OUT>sleep for 10 seconds...
2012-06-03 21:39:01,725 [Thread-1] INFO wls.OMSController run.1744 - <OUT>status of EMGC_OMS1:
2012-06-03 21:39:01,726 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:39:01,727 [Thread-1] INFO wls.OMSController run.1744 - <OUT>FAILED_NOT_RESTARTABLE
2012-06-03 21:39:41,739 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:39:41,739 [Thread-1] INFO wls.OMSController run.1744 - <OUT>sleep for 10 seconds...
2012-06-03 21:39:51,741 [Thread-1] INFO wls.OMSController run.1744 - <OUT>status of EMGC_OMS1:
2012-06-03 21:39:51,742 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:39:51,742 [Thread-1] INFO wls.OMSController run.1744 - <OUT>FAILED_NOT_RESTARTABLE
2012-06-03 21:40:01,746 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:40:01,746 [Thread-1] INFO wls.OMSController run.1744 - <OUT>sleep for 10 seconds...
2012-06-03 21:40:11,748 [Thread-1] INFO wls.OMSController run.1744 - <OUT>status of EMGC_OMS1:
2012-06-03 21:40:11,749 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:40:11,749 [Thread-1] INFO wls.OMSController run.1744 - <OUT>FAILED_NOT_RESTARTABLE
2012-06-03 21:40:41,758 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:40:41,758 [Thread-1] INFO wls.OMSController run.1744 - <OUT>sleep for 10 seconds...
2012-06-03 21:40:51,759 [Thread-1] INFO wls.OMSController run.1744 - <OUT>status of EMGC_OMS1:
2012-06-03 21:40:51,760 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:40:51,760 [Thread-1] INFO wls.OMSController run.1744 - <OUT>FAILED_NOT_RESTARTABLE
2012-06-03 21:40:51,760 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-03 21:40:51,760 [Thread-1] INFO wls.OMSController run.1744 - <OUT>timed out waiting for EMGC_OMS1 to be RUNNING
2012-06-03 21:40:51,761 [Thread-1] INFO wls.OMSController run.1744 - <OUT>status of node manager:
2012-06-03 21:40:51,761 [Thread-1] INFO wls.OMSController run.1744 - <OUT>Currently connected to Node Manager to monitor the domain GCDomain.
2012-06-03 21:40:51,761 [Thread-1] INFO wls.OMSController run.1744 - <OUT>1
2012-06-03 21:40:51,761 [Thread-1] INFO wls.OMSController run.1744 - <OUT>Successfully disconnected from Node Manager.
2012-06-03 21:40:51,762 [Thread-1] INFO wls.OMSController run.1744 - <OUT>END
2012-06-03 21:40:51,762 [Thread-2] INFO wls.OMSController run.1744 - <ERR>END
2012-06-03 21:40:51,777 [main] INFO wls.OMSController processCmd.1392 - wlst process is finished
2012-06-03 21:40:51,778 [main] INFO wls.OMSController processCmd.1394 - wlst process exited with code 1
2012-06-03 21:40:51,778 [main] INFO wls.OMSController processCmd.1396 - wlst outstream joined
2012-06-03 21:40:51,778 [main] INFO wls.OMSController processCmd.1398 - wlst errstream joined
2012-06-03 21:40:51,778 [main] INFO wls.OMSController processCmd.1406 - process exited with code 1
2012-06-03 21:40:51,781 [main] DEBUG oms.StatusOMSCmd processStatusOMS.159 - HTTP port in emgc property file: 7203
2012-06-03 21:40:51,781 [main] DEBUG oms.StatusOMSCmd processStatusOMS.160 - HTTPS port in emgc property file: 7302
2012-06-03 21:40:51,781 [main] DEBUG oms.StatusOMSCmd processStatusOMS.166 - Webtier HTTP port in emgc property file: 7789
2012-06-03 21:40:51,781 [main] DEBUG oms.StatusOMSCmd processStatusOMS.167 - Webtier HTTPS port in emgc property file: 7801
2012-06-03 21:40:51,781 [main] DEBUG oms.StatusOMSCmd processStatusOMS.186 - Using https port.
2012-06-03 21:40:51,782 [main] DEBUG oms.StatusOMSCmd processStatusOMS.203 - Using webtier https port.
2012-06-03 21:40:51,908 [main] DEBUG oms.StatusOMSCmd pingOMSCheck.341 - Attempting to connect to https://OEM12c-OMS-01.example.com:7302/em/faces/logon/core-uifwk-console-login
2012-06-03 21:40:51,924 [main] INFO oms.StatusOMSCmd processStatusOMS.294 - Failed to connect to em login page
2012-06-03 21:40:51,924 [main] INFO oms.StatusOMSCmd processStatusOMS.295 - Connection refused
2012-06-03 21:40:51,924 [main] INFO oms.StatusOMSCmd processStatusOMS.296 - Connection exception when trying to hit OMS page. OMS is down
2012-06-03 21:40:51,924 [main] INFO wls.OMSController statusOMS.1354 - statusOMS finished with result: 8
2012-06-03 21:40:51,924 [main] INFO wls.OMSController startOMS.940 - startOMS finished with result: 1
2012-06-03 21:40:51,925 [main] DEBUG oms.StatusOMSCmd processStatusOMS.159 - HTTP port in emgc property file: 7203
2012-06-03 21:40:51,925 [main] DEBUG oms.StatusOMSCmd processStatusOMS.160 - HTTPS port in emgc property file: 7302
2012-06-03 21:40:51,925 [main] DEBUG oms.StatusOMSCmd processStatusOMS.166 - Webtier HTTP port in emgc property file: 7789
2012-06-03 21:40:51,925 [main] DEBUG oms.StatusOMSCmd processStatusOMS.167 - Webtier HTTPS port in emgc property file: 7801
2012-06-03 21:40:51,926 [main] DEBUG oms.StatusOMSCmd processStatusOMS.186 - Using https port.
2012-06-03 21:40:51,926 [main] DEBUG oms.StatusOMSCmd processStatusOMS.203 - Using webtier https port.
2012-06-03 21:40:51,926 [main] DEBUG oms.StatusOMSCmd pingOMSCheck.341 - Attempting to connect to https://OEM12c-OMS-01.example.com:7302/em/faces/logon/core-uifwk-console-login
2012-06-03 21:40:51,927 [main] INFO oms.StatusOMSCmd processStatusOMS.294 - Failed to connect to em login page
2012-06-03 21:40:51,927 [main] INFO oms.StatusOMSCmd processStatusOMS.295 - Connection refused
2012-06-03 21:40:51,927 [main] INFO oms.StatusOMSCmd processStatusOMS.296 - Connection exception when trying to hit OMS page. OMS is down
2012-06-03 21:40:51,943 [main] INFO wls.OMSController statusOMS.1354 - statusOMS finished with result: 8
Thanks & Regards
Edited by: 938626 on Jun 5, 2012 12:06 AM
Edited by: 938626 on Jun 5, 2012 12:15 AMHi Akanksha,
Did more digging abt the issue and finally got the OMS server to actually start even after the certificate issue but after that when the script tries to access login page it gets a 404 error and stops the OMS server.
I guess raising an SR is my only way out.....
[oracle@OEM12c-OMS-01 bin]$ ./emctl start oms
Oracle Enterprise Manager Cloud Control 12c Release 12.1.0.1.0
Copyright (c) 1996, 2012 Oracle Corporation. All rights reserved.
Starting WebTier...
WebTier Successfully Started
Starting Oracle Management Server...
Oracle Management Server is Down
# tail -f /home/oracle/software/oracle/middleware/gc_inst/em/EMGC_OMS1/sysman/log/emctl.log
==========================
2012-06-06 10:11:38,742 [main] DEBUG wls.OMSController main.199 - Log location is /home/oracle/software/oracle/middleware/gc_inst/em/EMGC_OMS1/sysman/log/emctl.log
2012-06-06 10:11:38,746 [main] INFO wls.OMSController startOMS.828 - admin start is false
2012-06-06 10:11:38,746 [main] INFO wls.OMSController startOMS.829 - is service is false
2012-06-06 10:11:38,953 [main] INFO wls.OMSController getEnvProps.476 - Setting trust store system properties: -Dweblogic.security.TrustKeyStore=DemoTrust -Dweblogic.security.SSL.ignoreHostnameVerification=true -Djava.security.egd=file:///dev/./urandom
2012-06-06 10:11:38,954 [main] INFO wls.OMSController startOMS.848 - Starting WebTier...
2012-06-06 10:11:39,001 [main] INFO util.WebTierUtil execCmd.407 - Running the command: /home/oracle/software/oracle/middleware/gc_inst/WebTierIH1/bin/opmnctl stopall
2012-06-06 10:11:46,289 [main] INFO util.WebTierUtil getProcessResult.467 - opmnctl cmd output: opmnctl stopall: stopping opmn and all managed processes...
2012-06-06 10:11:46,290 [main] INFO util.WebTierUtil getProcessResult.475 - opmnctl cmd error:
2012-06-06 10:11:46,293 [main] INFO util.WebTierUtil getProcessResult.479 - opmnctl cmd exited with code 0
2012-06-06 10:11:46,295 [main] INFO util.WebTierUtil execCmd.407 - Running the command: /home/oracle/software/oracle/middleware/gc_inst/WebTierIH1/bin/opmnctl startall
2012-06-06 10:11:55,079 [main] INFO util.WebTierUtil getProcessResult.467 - opmnctl cmd output: opmnctl startall: starting opmn and all managed processes...
2012-06-06 10:11:55,092 [main] INFO util.WebTierUtil getProcessResult.475 - opmnctl cmd error:
2012-06-06 10:11:55,093 [main] INFO util.WebTierUtil getProcessResult.479 - opmnctl cmd exited with code 0
2012-06-06 10:11:55,094 [main] INFO wls.OMSController startOMS.859 - WebTier Successfully Started
2012-06-06 10:11:55,095 [main] INFO wls.OMSController startOMS.886 - wlst command is /home/oracle/software/oracle/middleware/oracle_common/common/bin/wlst.sh /home/oracle/software/oracle/middleware/oms/bin/startOMS.py
2012-06-06 10:11:55,096 [main] INFO wls.OMSController startOMS.887 - Executing the wlst command for startOMS...
2012-06-06 10:11:55,097 [main] INFO wls.OMSController startOMS.891 - optional admin start is false
2012-06-06 10:11:55,098 [main] INFO wls.OMSController startOMS.892 - optional pbsonly start is false
2012-06-06 10:11:55,277 [Thread-1] INFO wls.OMSController run.1744 - <OUT>CLASSPATH=/home/oracle/software/oracle/middleware/patch_wls1035/profiles/default/sys_manifest_classpath/weblogic_patch.jar:/home/oracle/software/oracle/middleware/jdk16/jdk/lib/tools.jar:/home/oracle/software/oracle/middleware/wlserver_10.3/server/lib/weblogic_sp.jar:/home/oracle/software/oracle/middleware/wlserver_10.3/server/lib/weblogic.jar:/home/oracle/software/oracle/middleware/modules/features/weblogic.server.modules_10.3.5.0.jar:/home/oracle/software/oracle/middleware/wlserver_10.3/server/lib/webservices.jar:/home/oracle/software/oracle/middleware/modules/org.apache.ant_1.7.1/lib/ant-all.jar:/home/oracle/software/oracle/middleware/modules/net.sf.antcontrib_1.1.0.0_1-0b2/lib/ant-contrib.jar:/home/oracle/software/oracle/middleware/patch_wls1035/profiles/default/sys_manifest_classpath/weblogic_patch.jar:/home/oracle/software/oracle/middleware/jdk16/jdk/lib/tools.jar:/home/oracle/software/oracle/middleware/wlserver_10.3/server/lib/weblogic_sp.jar:/home/oracle/software/oracle/middleware/wlserver_wlst.jar:/home/oracle/software/oracle/middleware/oracle_common/common/wlst/resources/oamap_help.jar:/home/oracle/software/oracle/middleware/oracle_common/common/wlst/resources/oamAuthnProvider.jar:/home/oracle/software/oracle/middleware/oracle_common/common/wlst/resources/ossoiap_help.jar:/home/oracle/software/oracle/middleware/oracle_common/common/wlst/resources/ossoiap.jar:/home/oracle/software/oracle/middleware/oracle_common/common/wlst/resources/ovdwlsthelp.jar:/home/oracle/software/oracle/middleware/oracle_common/common/wlst/resources/sslconfigwlst.jar:/home/oracle/software/oracle/middleware/oracle_common/common/wlst/resources/wsm-wlst.jar
2012-06-06 10:11:55,278 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-06 10:11:55,278 [Thread-1] INFO wls.OMSController run.1744 - <OUT>PATH=/home/oracle/software/oracle/middleware/wlserver_10.3/server/bin:/home/oracle/software/oracle/middleware/modules/org.apache.ant_1.7.1/bin:/home/oracle/software/oracle/middleware/jdk16/jdk/jre/bin:/home/oracle/software/oracle/middleware/jdk16/jdk/bin:/home/oracle/software/oracle/middleware/oms/bin:/home/oracle/software/oracle/middleware/oms/jdk/bin:/home/oracle/software/oracle/middleware/oms/perl/bin:/home/oracle/software/oracle/middleware/wlserver_10.3/server/bin:/home/oracle/software/oracle/middleware/modules/org.apache.ant_1.7.1/bin:/home/oracle/software/oracle/middleware/jdk16/jdk/jre/bin:/home/oracle/software/oracle/middleware/jdk16/jdk/bin:/usr/lib64/qt-3.3/bin:/usr/local/bin:/bin:/usr/bin:/usr/local/sbin:/usr/sbin:/sbin:/home/oracle/bin:/bin:/usr/bin
2012-06-06 10:11:55,279 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-06 10:11:55,284 [Thread-1] INFO wls.OMSController run.1744 - <OUT>Your environment has been set.
2012-06-06 10:11:55,288 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-06 10:11:55,289 [Thread-1] INFO wls.OMSController run.1744 - <OUT>CLASSPATH=/home/oracle/software/oracle/middleware/patch_wls1035/profiles/default/sys_manifest_classpath/weblogic_patch.jar:/home/oracle/software/oracle/middleware/jdk16/jdk/lib/tools.jar:/home/oracle/software/oracle/middleware/wlserver_10.3/server/lib/weblogic_sp.jar:/home/oracle/software/oracle/middleware/wlserver_10.3/server/lib/weblogic.jar:/home/oracle/software/oracle/middleware/modules/features/weblogic.server.modules_10.3.5.0.jar:/home/oracle/software/oracle/middleware/wlserver_10.3/server/lib/webservices.jar:/home/oracle/software/oracle/middleware/modules/org.apache.ant_1.7.1/lib/ant-all.jar:/home/oracle/software/oracle/middleware/modules/net.sf.antcontrib_1.1.0.0_1-0b2/lib/ant-contrib.jar:/home/oracle/software/oracle/middleware/patch_wls1035/profiles/default/sys_manifest_classpath/weblogic_patch.jar:/home/oracle/software/oracle/middleware/jdk16/jdk/lib/tools.jar:/home/oracle/software/oracle/middleware/wlserver_10.3/server/lib/weblogic_sp.jar:/home/oracle/software/oracle/middleware/wlserver_10.3/server/lib/weblogic.jar:/home/oracle/software/oracle/middleware/modules/features/weblogic.server.modules_10.3.5.0.jar:/home/oracle/software/oracle/middleware/wlserver_10.3/server/lib/webservices.jar:/home/oracle/software/oracle/middleware/modules/org.apache.ant_1.7.1/lib/ant-all.jar:/home/oracle/software/oracle/middleware/modules/net.sf.antcontrib_1.1.0.0_1-0b2/lib/ant-contrib.jar:/home/oracle/software/oracle/middleware/oms/sysman/jlib/emagentSDK.jar:/home/oracle/software/oracle/middleware/oms/sysman/jlib/emCORE.jar:/home/oracle/software/oracle/middleware/oracle_common/modules/oracle.http_client_11.1.1.jar:/home/oracle/software/oracle/middleware/oracle_common/modules/oracle.pki_wlst.jar:/home/oracle/software/oracle/middleware/oracle_common/common/wlst/resources/oamap_help.jar:/home/oracle/software/oracle/middleware/oracle_common/common/wlst/resources/oamAuthnProvider.jar:/home/oracle/software/oracle/middleware/oracle_common/common/wlst/resources/ossoiap_help.jar:/home/oracle/software/oracle/middleware/oracle_common/common/wlst/resources/ossoiap.jar:/home/oracle/software/oracle/middleware/oracle_common/common/wlst/resources/ovdwlsthelp.jar:/home/oracle/software/oracle/middleware/oracle_common/common/wlst/resources/sslconfigwlst.jar:/home/oracle/software/oracle/middleware/oracle_common/common/wlst/resources/wsm-wlst.jar:/home/oracle/software/oracle/middleware/utils/config/10.3/config-launch.jar::/home/oracle/software/oracle/middleware/wlserver_10.3/common/derby/lib/derbynet.jar:/home/oracle/software/oracle/middleware/wlserver_10.3/common/derby/lib/derbyclient.jar:/home/oracle/software/oracle/middleware/wlserver_10.3/common/derby/lib/derbytools.jar::
2012-06-06 10:12:01,592 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-06 10:12:01,593 [Thread-1] INFO wls.OMSController run.1744 - <OUT>Initializing WebLogic Scripting Tool (WLST) ...
2012-06-06 10:12:01,598 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-06 10:12:18,456 [Thread-1] INFO wls.OMSController run.1744 - <OUT>Welcome to WebLogic Server Administration Scripting Shell
2012-06-06 10:12:18,457 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-06 10:12:18,457 [Thread-1] INFO wls.OMSController run.1744 - <OUT>Type help() for help on available commands
2012-06-06 10:12:18,458 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-06 10:12:18,671 [Thread-1] INFO wls.OMSController run.1744 - <OUT>nm home is /home/oracle/software/oracle/middleware/gc_inst/NodeManager/emnodemanager
2012-06-06 10:12:18,675 [Thread-1] INFO wls.OMSController run.1744 - <OUT>is_admin_host is TRUE
2012-06-06 10:12:18,675 [Thread-1] INFO wls.OMSController run.1744 - <OUT>admin_start is FALSE
2012-06-06 10:12:18,676 [Thread-1] INFO wls.OMSController run.1744 - <OUT>admin_only_start is NONE
2012-06-06 10:12:20,113 [Thread-1] INFO wls.OMSController run.1744 - <OUT>Connecting to Node Manager ...
2012-06-06 10:12:20,743 [Thread-1] INFO wls.OMSController run.1744 - <OUT><Jun 6, 2012 10:12:20 AM IST> <Info> <Security> <BEA-090906> <Changing the default Random Number Generator in RSA CryptoJ from ECDRBG to FIPS186PRNG. To disable this change, specify -Dweblogic.security.allowCryptoJDefaultPRNG=true>
2012-06-06 10:12:24,198 [Thread-1] INFO wls.OMSController run.1744 - <OUT><Jun 6, 2012 10:12:24 AM IST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=Entrust Root Certification Authority - G2,OU=(c) 2009 Entrust\, Inc. - for authorized use only,OU=See www.entrust.net/legal-terms,O=Entrust\, Inc.,C=US". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
2012-06-06 10:12:24,236 [Thread-1] INFO wls.OMSController run.1744 - <OUT><Jun 6, 2012 10:12:24 AM IST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=thawte Primary Root CA - G3,OU=(c) 2008 thawte\, Inc. - For authorized use only,OU=Certification Services Division,O=thawte\, Inc.,C=US". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
2012-06-06 10:12:24,280 [Thread-1] INFO wls.OMSController run.1744 - <OUT><Jun 6, 2012 10:12:24 AM IST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=T-TeleSec GlobalRoot Class 3,OU=T-Systems Trust Center,O=T-Systems Enterprise Services GmbH,C=DE". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
2012-06-06 10:12:24,284 [Thread-1] INFO wls.OMSController run.1744 - <OUT><Jun 6, 2012 10:12:24 AM IST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=T-TeleSec GlobalRoot Class 2,OU=T-Systems Trust Center,O=T-Systems Enterprise Services GmbH,C=DE". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
2012-06-06 10:12:24,306 [Thread-1] INFO wls.OMSController run.1744 - <OUT><Jun 6, 2012 10:12:24 AM IST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=GlobalSign,O=GlobalSign,OU=GlobalSign Root CA - R3". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
2012-06-06 10:12:24,342 [Thread-1] INFO wls.OMSController run.1744 - <OUT><Jun 6, 2012 10:12:24 AM IST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "OU=Security Communication RootCA2,O=SECOM Trust Systems CO.\,LTD.,C=JP". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
2012-06-06 10:12:24,356 [Thread-1] INFO wls.OMSController run.1744 - <OUT><Jun 6, 2012 10:12:24 AM IST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=VeriSign Universal Root Certification Authority,OU=(c) 2008 VeriSign\, Inc. - For authorized use only,OU=VeriSign Trust Network,O=VeriSign\, Inc.,C=US". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
2012-06-06 10:12:24,419 [Thread-1] INFO wls.OMSController run.1744 - <OUT><Jun 6, 2012 10:12:24 AM IST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=KEYNECTIS ROOT CA,OU=ROOT,O=KEYNECTIS,C=FR". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
2012-06-06 10:12:24,439 [Thread-1] INFO wls.OMSController run.1744 - <OUT><Jun 6, 2012 10:12:24 AM IST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=GeoTrust Primary Certification Authority - G3,OU=(c) 2008 GeoTrust Inc. - For authorized use only,O=GeoTrust Inc.,C=US". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
2012-06-06 10:12:25,049 [Thread-1] INFO wls.OMSController run.1744 - <OUT>Successfully Connected to Node Manager.
2012-06-06 10:12:25,051 [Thread-1] INFO wls.OMSController run.1744 - <OUT>status of node manager:
2012-06-06 10:12:25,052 [Thread-1] INFO wls.OMSController run.1744 - <OUT>Currently connected to Node Manager to monitor the domain GCDomain.
2012-06-06 10:12:25,052 [Thread-1] INFO wls.OMSController run.1744 - <OUT>current status of EMGC_ADMINSERVER:
2012-06-06 10:12:25,053 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-06 10:12:25,053 [Thread-1] INFO wls.OMSController run.1744 - <OUT>RUNNING
2012-06-06 10:12:25,054 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-06 10:12:25,054 [Thread-1] INFO wls.OMSController run.1744 - <OUT>current status of EMGC_OMS1:
2012-06-06 10:12:25,057 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-06 10:12:25,057 [Thread-1] INFO wls.OMSController run.1744 - <OUT>RUNNING
2012-06-06 10:12:25,057 [Thread-1] INFO wls.OMSController run.1744 - <OUT>
2012-06-06 10:12:25,057 [Thread-1] INFO wls.OMSController run.1744 - <OUT>status of node manager:
2012-06-06 10:12:25,058 [Thread-1] INFO wls.OMSController run.1744 - <OUT>Currently connected to Node Manager to monitor the domain GCDomain.
2012-06-06 10:12:25,058 [Thread-1] INFO wls.OMSController run.1744 - <OUT>1
2012-06-06 10:12:25,059 [Thread-1] INFO wls.OMSController run.1744 - <OUT>Successfully disconnected from Node Manager.
2012-06-06 10:12:25,060 [Thread-1] INFO wls.OMSController run.1744 - <OUT>END
2012-06-06 10:12:25,061 [Thread-2] INFO wls.OMSController run.1744 - <ERR>END
2012-06-06 10:12:25,081 [main] INFO wls.OMSController processCmd.1392 - wlst process is finished
2012-06-06 10:12:25,082 [main] INFO wls.OMSController processCmd.1394 - wlst process exited with code 2
2012-06-06 10:12:25,082 [main] INFO wls.OMSController processCmd.1396 - wlst outstream joined
2012-06-06 10:12:25,083 [main] INFO wls.OMSController processCmd.1398 - wlst errstream joined
2012-06-06 10:12:25,083 [main] INFO wls.OMSController processCmd.1406 - process exited with code 2
2012-06-06 10:12:25,124 [main] DEBUG oms.StatusOMSCmd processStatusOMS.159 - HTTP port in emgc property file: 7203
2012-06-06 10:12:25,125 [main] DEBUG oms.StatusOMSCmd processStatusOMS.160 - HTTPS port in emgc property file: 7302
2012-06-06 10:12:25,125 [main] DEBUG oms.StatusOMSCmd processStatusOMS.166 - Webtier HTTP port in emgc property file: 7790
2012-06-06 10:12:25,125 [main] DEBUG oms.StatusOMSCmd processStatusOMS.167 - Webtier HTTPS port in emgc property file: 7803
2012-06-06 10:12:25,125 [main] DEBUG oms.StatusOMSCmd processStatusOMS.186 - Using https port.
2012-06-06 10:12:25,126 [main] DEBUG oms.StatusOMSCmd processStatusOMS.203 - Using webtier https port.
2012-06-06 10:12:25,497 [main] DEBUG oms.StatusOMSCmd pingOMSCheck.341 - Attempting to connect to https://OEM12c-OMS-01.example.com:7302/em/faces/logon/core-uifwk-console-login
2012-06-06 10:12:26,986 [main] DEBUG oms.StatusOMSCmd pingOMSCheck.341 - Attempting to connect to https://OEM12c-OMS-01.example.com:7803/empbs/check
2012-06-06 10:12:27,007 [main] DEBUG oms.StatusOMSCmd processStatusOMS.240 - console page status code is 404
2012-06-06 10:12:27,050 [main] DEBUG oms.StatusOMSCmd processStatusOMS.242 - pbs page status code is 200
2012-06-06 10:12:27,051 [main] DEBUG oms.StatusOMSCmd processStatusOMS.245 - console header is null
2012-06-06 10:12:27,051 [main] DEBUG oms.StatusOMSCmd processStatusOMS.247 - pbs header is null
2012-06-06 10:12:27,051 [main] DEBUG oms.StatusOMSCmd processStatusOMS.287 - Encountered error while hitting page. Status code is 404
2012-06-06 10:12:27,051 [main] INFO oms.StatusOMSCmd processStatusOMS.294 - Failed to connect to em login page
2012-06-06 10:12:27,052 [main] INFO oms.StatusOMSCmd processStatusOMS.295 - Encountered error while hitting page. Status codes are 404 for console and 200 for PBS
2012-06-06 10:12:27,052 [main] INFO oms.StatusOMSCmd processStatusOMS.296 - Connection exception when trying to hit OMS page. OMS is down
2012-06-06 10:12:27,052 [main] INFO wls.OMSController statusOMS.1354 - statusOMS finished with result: 8
2012-06-06 10:12:27,052 [main] INFO wls.OMSController startOMS.940 - startOMS finished with result: 2
2012-06-06 10:12:27,053 [main] DEBUG oms.StatusOMSCmd processStatusOMS.159 - HTTP port in emgc property file: 7203
2012-06-06 10:12:27,054 [main] DEBUG oms.StatusOMSCmd processStatusOMS.160 - HTTPS port in emgc property file: 7302
2012-06-06 10:12:27,054 [main] DEBUG oms.StatusOMSCmd processStatusOMS.166 - Webtier HTTP port in emgc property file: 7790
2012-06-06 10:12:27,054 [main] DEBUG oms.StatusOMSCmd processStatusOMS.167 - Webtier HTTPS port in emgc property file: 7803
2012-06-06 10:12:27,055 [main] DEBUG oms.StatusOMSCmd processStatusOMS.186 - Using https port.
2012-06-06 10:12:27,055 [main] DEBUG oms.StatusOMSCmd processStatusOMS.203 - Using webtier https port.
2012-06-06 10:12:27,056 [main] DEBUG oms.StatusOMSCmd pingOMSCheck.341 - Attempting to connect to https://OEM12c-OMS-01.example.com:7302/em/faces/logon/core-uifwk-console-login
2012-06-06 10:12:27,074 [main] DEBUG oms.StatusOMSCmd pingOMSCheck.341 - Attempting to connect to https://OEM12c-OMS-01.example.com:7803/empbs/check
2012-06-06 10:12:27,102 [main] DEBUG oms.StatusOMSCmd processStatusOMS.240 - console page status code is 404
2012-06-06 10:12:27,104 [main] DEBUG oms.StatusOMSCmd processStatusOMS.242 - pbs page status code is 200
2012-06-06 10:12:27,108 [main] DEBUG oms.StatusOMSCmd processStatusOMS.245 - console header is null
2012-06-06 10:12:27,108 [main] DEBUG oms.StatusOMSCmd processStatusOMS.247 - pbs header is null
2012-06-06 10:12:27,108 [main] DEBUG oms.StatusOMSCmd processStatusOMS.287 - Encountered error while hitting page. Status code is 404
2012-06-06 10:12:27,109 [main] INFO oms.StatusOMSCmd processStatusOMS.294 - Failed to connect to em login page
2012-06-06 10:12:27,109 [main] INFO oms.StatusOMSCmd processStatusOMS.295 - Encountered error while hitting page. Status codes are 404 for console and 200 for PBS
2012-06-06 10:12:27,109 [main] INFO oms.StatusOMSCmd processStatusOMS.296 - Connection exception when trying to hit OMS page. OMS is down
2012-06-06 10:12:27,647 [main] INFO wls.OMSController statusOMS.1354 - statusOMS finished with result: 8
Regards,
Lokesh -
Enserver not starting up during installation of CE 7.1
Hi,
I am trying to install Netweaver CE version 7.1 SP5 on windows XP. In the installing phase configure UME it stops saying "Instance CE1/SCS01 [PARTIAL] did not start after 5:00 minutes. Giving up.)". and when i checked the log i can see the server status as
name, description, dispstatus, textstatus, starttime, elapsedtime, pid
msg_server.EXE, MessageServer, GREEN, Running, 2008 07 14 12:40:16, 0:05:01, 6120
enserver.EXE, EnqueueServer, GRAY, Stopped, 2008 07 14 12:40:32, 0:00:03, -1
gwrd.EXE, Gateway, GREEN, Running, 2008 07 14 12:40:18, 0:04:59, 5080
from the log i could find that enserver.exe is not able to start up. what could be the reason for that.? i recently changed the virtual memory size. whether it could cause this error?Hi,
some how I managed to solve this problem.
But now when i am starting the server, the enserver starts and crashes.
I tried to run the enserver stand alone by C:\usr\sap\CE1\SYS\exe\uc\NTI386>enserver.EXE pf=C:\usr\sap\CE1\SYS\profile\ command
Server initialisation failed!
Reason: "generic enqueue error detected at enio.cpp:194 Errorinfo: "Cannot resolve service <sapdp01>""
what could be the reason for this error?
Thanks -
Apple Mobile Device Failed to Start error during installation of iTunes
In an attempt to update my iTunes to the latest version, as prompted by a pop-up, the update failed. I then tried to open iTunes from my desktop but a pop-up displayed that the program wasn't working properly and that I should re-install iTunes. I removed the program and then attempted to re-install. Midway through the install, I receive an error message that "Services "Apple Mobile Device" (Apple Mobile Device) failed to start. Verify that you have sufficient privileges to start system services.
I can either Abort, Retry, or Cancel...none of which completes the install.
Help.Chaps and chapesses,
I too was having the same problem when I tried to update and then unfortunately uninstall and re-install itunes. But, like Nige above me says, you need to uninstall all your Apple software and then re-install itunes.
Have a look at the response given to this forum post:
https://discussions.apple.com/thread/5819470?tstart=0
I did exactly as the turingtest2 said:
I removed all of these items in the following order:
iTunes
Apple Software Update
Apple Mobile Device Support
Bonjour
Apple Application Support
Then I restarted my computer, and the install of itunes worked like a dream. None of this ignore, abort, cancel nonsense.
Hopefully all your respective versions of itunes will work soon. Cheers Nigel280 -
Facing issue during installation of SAP ERP6.0 Ehp7 on Linux : SAP HANA database
Hi,
We are facing an issue at phase 10 of 26 "Start Instance", during installation of ERP 6.0 Ehp7 on linux.
The error is as follows.
Also find the sapinst_dev.log
Kindly, help in resolving the issue.
Thanks in advance.Hi Benjamin,
Kindly find the last few lines from dev_w0 below: -
I have accidently shut down my Mac Book Pro during windows 7 installation . When I re started it it began to say " Press any key to boot from CD or DVD " but the keyboard is not working . So I cannot boot It and the CD is also in the drive . Please help me to boot back to Mac book Pro and give me a way to start the key bord .
Hey rudreshchoubey,
Thanks for the question. The following resource may help to resolve your issue:
Boot Camp Installation & Setup Guide
http://manuals.info.apple.com/MANUALS/1000/MA1636/en_US/boot_camp_install-setup_ 10.8.pdf
If Windows doesn’t install properly
Verify that you’re using an original, full version of the 64-bit version of Windows 7 Home Premium, Windows 7 Professional, Windows 7 Ultimate, Windows 8, or Windows 8 Pro.
Restart your Mac and hold down the Option key until one or more disk icons appear on your screen. Insert the Windows installation disc into the optical drive or insert the USB flash drive with Windows into a USB port on your Mac. Select the Windows installation disk icon, then click the arrow beneath it. Quickly press any key on your keyboard to start the installer. Follow the onscreen instructions to repair or reinstall Windows.
Thanks,
Matt M. -
Lenovo U310: Clean Windows 7 Installation Guide (including Rapid Start and Caching)
Hi there,
this is the first time that I am writing such a guide/tutorial/whatever you may call it – there are probably better ones, but though not being a total computer noob, it took me almost one week to get this pretty (now again) little beast running again. So hopefully this helps some others to avoid such stupid downtimes.
A brief overview on what has happened to my original win 7 Home Premium:
As some may know, this laptop is very well usable as a “Hackintosh” called Macbook clone. So that’s what I did. It turned out to be nice, but I wanted to go back to Windows after a while, using a clean W7 Pro installation to start over. Actually an easy task, format all drives, install Windows, be happy. Just as I had been doing this for years. Unfortunately, it turned out to be a real challenge. First, I couldn’t “see” my drives during installation (and thus not install), then I got random errors during installation aborting it at different points and finally rapid start and caching didn’t work. Every time I tried to activate them (after Win installation), it crashed my PC. I even found an (official Lenovo!) guide stating to install W7 on the SSD, which worked, but sucks due to space limitations. Oh and another very nice thing: The SSD showed up during WIN installation (but not the classical hard drive) stating it was about 60 GB. So as you can see, I have had a lot of different tries and errors. Why I didn’t use Lenovo Easy Recover? As said before, I erased all partitions…
Before we start: If you have a good Windows running on the Laptop, do yourself a favor and disconnect the RAID 0 disks using the Intel Rapid Storage Application before(!!!) proceeding. It will make things much easier. And don’t forget to get all you data on an external drive or something.
Ok, now let’s start.
1.) Prepare a USB Stick with the following driver
http://downloadcenter.intel.com/Detail_Desc.aspx?DwnldID=21730 (choose f6flpy-x64.zip If you’re running a
64-bit system (standard nowadays), take f6flpy-x86.zip if it is a 32-bit Windows, just download and copy them
into the stick’s root directory) and plug this stick in one of the left side USB ports.
2.) You’ll need Win 7 on either a DVD (plus external drive, for sure) or (bootable) USB stick
3.) Connect your drive/stick (with W7) to the right side USB port.
4.) Switch the computer on, immediately hit FN and F2. That will open the BIOS.
5.) In the BIOS, navigate to the very right section (“save and exit”) and navigate the cursor to “load setup defaults”.
Hit enter to approve.
6.) After that, go to the “boot” tab and disable UEFI-boot.
7.) Next, go one more tab to the left and set the controller setting to RAID (NOT AHCI or Compatible!!!).
8.) Navigate the cursor down to “Intel Rapid Start” and hit enter. A submenu will pop up-
9.) Disable the first entry in that window, that will make the rest be disabled as well.
10.) Navigate to the very right tab, this time hit save and exit.
11.) The PC restarts.
12.) Immediately hit FN and F12 to open the boot selection menu. Select to boot from your W7 DVD drive or USB
stick.
13.) Click yourself through the whole process of installing Windows 7 until the page comes up where you will have
to select where to install it.
14.) Click on “load drivers” and after a few seconds your downloaded driver should be there. Click ok to use them.
Please do this step even if you can see your drives (SSD Disk 0, 32 GB and HDD Disk 1, 465(<-?) GB) as you
would expect them – otherwise you’re very likely to get an error during the install process.
15.) Now erase all partitions on both drives and select the HDD as the drive to install W7 to – NOT THE SSD!!!!!
Seriously, don’t choose the SSD.
16.) Windows will probably say that some extra partitions are necessary and so on, click ok and install Windows.
17.) After the installation has finished and you see your Desktop, I suggest you to proceed with the next steps in the
following order to see as early as possible if you are on the right way.
18.) Install the Chipset driver, restart.
19.) Install the Intel Rapid Storage “driver” and check the box where it asks to additionally install the control center.
Reboot.
20.) Go into BIOS (FN and F2) and enable Intel Rapid Start (the one you disabled in Step 8 and 9)
21.) Boot into Windows.
22.) Click on the Windows button, type cmd and right klick on the cmd.exe, select to run it as Admin.
23.) Now you’ll create a hibernation partition on the SSD. (which by now should be completely empty as we’ve
deleted all partitions in step 15)
24.) In the command prompt that we have just opened, type: (without quotas, for sure)
“diskpart” and hit the enter button
“list disk” and hit the enter button
Now you should see your ssd as disk 0 and your hdd as disk 1
If your ssd is disk 0 (that would be standard), write “select disk 0”, otherwise write: “select disk 1”, and hit the enter button.
Now write “create partition primary size=4096” and hit enter again. [if you have 4GB of ram, type 4096, if you have 8 GB of ram, use 8192]
Now write “detail disk” and hit enter to see the volume number behind the volume that we have just created (it is 4 GB or 8 respectively, should be easy to find), in my case that was “2”
Now type “select volume 2” if your 4 or 8 GB volume has number 2 as well, otherwise use the number you found out in step f. Hit enter.
Finally, type: “set id=84 override” and hit enter for one last time.
It should now say back that the id has been set successfully.
Exit the command prompt. (close)
25.) Reboot
26.) Install the Rapid Start driver. Reboot.
27.) Open the Intel Rapid Storage Application.
28.) Click on accelerate and approve the settings. Two RAID’s will be created. Reboot.
29.) Install the remaining drivers, have fun with Windows Update and that’s it!
Good luck to all of you… And hey Lenovo - wouldn't that have been your job after all these posts showing your costumers in trouble? Just my two cents...
If you want, you can now turn on UEFI-boot in BIOS.
PS: If, after installing all drivers, you happen to see one unknown device in your device manager – this one belongs to Lenovo Connect Software that came with your Laptop. (Updates FB, Email etc when PC is in sleep mode) If you install Lenovo Connect it’s going to be fine, however, I would not recommend it as it is said to use a lot of energy and cause some other problems. So just live with it, your PC is totally fine without it.
Kind regards from ShanghaiSeriously guys, I can't use my 3 days old laptop. Some help would be mostly appreciated. At this point, the network connection issue doesn't show up anymore, it's just a blank screen after reboot. I reinstall windows and do it all over again just to achieve the same result.
Now couple of things caught my attention: as I load the "6flpy-x64.zip" driver from step 14, I get a message saying I need to install signed drivers, because unsigned ones are likely to mess up the system.
Secondly, I could not find any Rapid Storage Technology drivers for Windows 7 (particularly for U310 model), so I use the Windows 8 ones (http://support.lenovo.com/en_US/downloads/detail.page?DocID=DS031455), which seems a silly thing, yet I know of no alternatives.
Could it be any of these issues to cause my problem? Or smth else? Please help! -
I have tried to download itunes 10.5 but during installation it gives an error of windows installer.Please let me know how to install it.
Repair youe Apple Software Update.
Go to START/ALL PROGRAMS/Apple Software Update. If it offers you a newer version of Apple Software Update, do it but Deselect any other software offered at the same time. Once done, try another iTunes install.
If you don't find ASU in All Programs, go to Control Panel, Add & Remove Programs. -
HT3986 i get a black screen during windows 7 installation on bootcamp 5.0.1
i get a black screen during windows 7 installation on bootcamp 5.0.1 , it wont install
Hi wb2009,
I haven't found that the TV would be an issue, but did find an article that states to not have extra USB devices connected.
Boot Camp: Windows installation boots to black screen with blinking cursor
http://support.apple.com/kb/TS4536
The Windows installation may boot to a black screen with a blinking cursor. This can occur if you use a USB optical drive or USB Flash drive for the Windows installation and another USB device is also connected to the computer.
There's another article that mentions Windows XP or Vista that may apply.
Archived - Boot Camp: Start up to black screen after installing Windows
http://support.apple.com/kb/TS2600
Thank you for visiting Apple Support Communities.
Nubz -
Boot Camp: iMac displays a black screen during installation of Windows 7 - Apple Support
I have followed each of the steps listed in the link above with no success.
Prior to adding the extra drivers I was able to start the Windows install process up to reformatting the "Windows" Bootcamp drive. After that the computer would go through some instal processes and eventually restart. After the restart the screen would go black. The black screen lead me to the Apple Support link above dated March 5 2015. After going through steps listed in the link above, I get an error message stating that the D:\Sources\instal.win. file cannot be located. I am forced to restart the computer at that point and theWindows install process attempts to start again but always ends up at the same point.
Note: I am installing windows 7 Pro from a DVD. I scanned the AutoUnattend.xml file and noticed that it refers to "Windows 7 ULTIMATE" but not "Pro" or any others that I could see. (see below). Could that be part of the issue?
Any feedback would be greatly appreciated.
<cpi:offlineImage cpi:source="wim:d:/sources/install.wim#Windows 7 ULTIMATE" xmlns:cpi="urn:schemas-microsoft-com:cpi" />
</unattend>
iMac (27-inch, Late 2009)
2.66 GHz Intel Core i5
16 GB 1067 MHz DDR3
ATI Radeon HD 4850 512 MBHere is an over-simplified explanation of WIM and CLG files. Assume your DVD Media contains
W7- Ultimate
W7- Professional
W7- Home Premium
W7- Home Basic
WIM Files
File1
y
y
y
y
File2
y
y
y
y
File3
y
File4
y
y
File4
y
y
y
The File .wim will contains a compressed image which contains File [1...5].
The W7-Ultimate .clg will have 5 entries, with all set to 'Y'.
The W7-Professional .clg will have 5 entries, with 'Y','Y','N','Y','Y'.
The W7-Home Premium .clg will have 5 entries, with 'Y','Y','N','N','Y'.
The W7-Home Basic .clg file will have 5 entries, with 'Y','Y','N','N','N'.
This allows a single .wim Image file on the DVD media to be used to install any of the 5 flavors of Windows. When you enter your product key, the Installer knows what specific W7 variant you have the key for and will tell the WIM to extract the specific files the installer needs to be extracted.
The following line
<cpi:offlineImage cpi:source="wim:d:/sources/install.wim#Windows 7 ULTIMATE" xmlns:cpi="urn:schemas-microsoft-com:cpi" />
is telling that a retail product key will be entered, which should go look for this specific .clg file (from the five you already have on disk). You can test if it will work for you by changing this line to the following
<cpi:offlineImage cpi:source="wim:d:/sources/install.wim#Windows 7 PROFESSIONAL" xmlns:cpi="urn:schemas-microsoft-com:cpi" />
If it does not work, the other issue can be related to device discovery. Typically A: and B: device names are reserved for Floppy Drives. C: is your internal HDD.
D: can either point to the Optical drive, or the USB. The normal convention is that the removable media is named from Z: backwards. Y: and Z: are usually used for Network drives, so X: should be your USB. First try with the change to "Professional". If it does not work, -
During installation from DVD of Adobe Photoshop Lightroom 4 the program is searching for msvr100.dll which is not available in my Windows 7 files. What to do?
This provides those files Error "Unable to start correctly - 0Xc00007b"
-
J2EE server does not start during installation
Hi,
I am installing WebAS JAVA 640 (NW04 SR1) on a Windows 2003/MSSQL server. I am using JAVA SDK 1.4.2_9. The installation stops at step 24/25 whereby the installer waits for the J2EE engine to start. After making 3 attempts to start the J2EE server, the installation process just hangs and I have to Cancel the installation.
BTW, I am specifying a heap size of 1024 MB and using the "Database Only" option as UME data store during installation.
Having checked the trace and log files, it seems the UME service fails to start, throws an exception and the message "the start of a core service failed, Web AS will not start".
According to the information available <a href="http://help.sap.com/saphelp_nw2004s/helpdata/en/20/361941edd5ef23e10000000a155106/content.htm">here</a>, I have checked the settings and it seems that option 2, <b>"User or group data is missing"</b> is causing the problem since database content of UME is missing. I have tried selecting entries from table UME_STRINGS but this table is empty.
Now, the same link says that I should login to UME web application as SAP* but the problem is that without the J2EE engine starting up, I cannot login and create missing users/groups.
Any ideas???
Regards
ShehryarThanks to all who replied. I have actually tried all options suggested like waiting for retries until the box appears, trying to manually start the server, and reducing heap size. None worked for me. For your information, I have a 2.4 GHz machine with 4GB RAM so I think heap size should not be an issue. I checked SAP Note regarding heap size issues in Win 2003 but that does not seem to apply in my case since my system does not behave abnormally with JVM settings.
Thanks again and I'll give it another shot.
Regards
Shehryar
Maybe you are looking for
-
SAP GUI Error - (GSS-APP DLL) on Windows Vista!
Hi All I am getting an error when setting up SAP GUI version 710 on Windows Vista. When I try to set up an snc logon i get the following message: Unable to load the GSS-API DLL named 'sncgss32.dll' On Windows XP we have a GSSAPI32.DLL in the C drive
-
Bought iPhone 5 do I need to upgrade from OS 10.6.8?
I am so confused. Mac Mini running OS10.6.8 I use iPhoto '09 ver 8.1.2 but prefer to edit in Photoshop CS5. I bought an iPhone 5 and the sales people talked about iCloud to sync with other devices, including automatically sharing photos with my Mac.
-
Hi all, I have a BEx report that displays a list of empnos and their details based on a selection. Now I want to count the number of recrods that were selected and display the total number of records that were selected. How can this be done? Thanks,
-
Where do I find my Airport Express password?
How can I retrieve my Airport Express password?
-
Greyed out apple id in settings hence unable to switch between ID's
hi all, I have just murchased my second ipad and after seiiting up i have decided to create a seperate account for the kids,however my issue is that when i go to the ID in the settings menu it is greyed out. its not blocked via restrictions hence uns