Standby PRI not working with voice Gateway Router & CUCM

Hi ALL ,
GOOD Day all of you .
I am facing a big problem i.e standby PRI not working with VG & CUCM , I have checked all the configuration parameter on VG & CUCM found ok but I am unable to make any call from standby link also incoming not come on the standby link . When I make a call on my Pilot no but getting busy tone .
I observer the some errors on VG like Cause i = 0x8286 - Channel unacceptable on my second PRI channel .
Please help me to reslove this proem .
Following are the PRI configuration Parameter on CUCM .
Product Specific Configuration Layout
Line Coding : HDB3
Framing : NON CRC4
Clock : External
Input Gain (-6..14 db) 0
Output Attenuation (-6..14 db) 0
Echo Cancellation Enable
Echo Cancellation Coverage (ms) 64
PRI configuration on VG
interface Serial0/0/1:15
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
isdn bind-l3 ccm-manager
BR,
SANDIPAN

Hi Craig ,
Thanks for your reply .
We are using the full 30 channel E1 PRI .
following are PRI Channel Statistics:
%Q.931 is backhauled to CCM MANAGER 0x0003 on DSL 1. Layer 3 output may not apply
ISDN Se0/0/0:15, Channel [1-31]
Configured Isdn Interface (dsl) 1
   Channel State (0=Idle 1=Proposed 2=Busy 3=Reserved 4=Restart 5=Maint_Pend)
    Channel : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    State   : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
   Service State (0=Inservice 1=Maint 2=Outofservice 8=MaintPend 9=OOSPend)
    Channel : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    State   : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Please find following debug error
VG_RO_01#isdn test call interface serial 0/0/0:15 09665484798
Mar 7 03:00:54.570: ISDN Se0/0/0:15 Q921: User RX <- RRp sapi=0 tei=0 nr=5
Mar 7 03:00:54.570: ISDN Se0/0/0:15 Q921: User TX -> RRp sapi=0 tei=0 nr=4
Mar 7 03:00:54.570: ISDN Se0/0/0:15 Q921: User TX -> RRf sapi=0 tei=0 nr=4
Mar 7 03:00:54.574: ISDN Se0/0/0:15 Q921: User RX <- RRf sapi=0 tei=0 nr=5
CCIL_PUNE_DR_VG_RO_01#
Mar 7 03:00:55.994: ISDN Se0/0/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x1, Called num 09665484798
Mar 7 03:00:55.994: ISDN Se0/0/0:15 Q921: User TX -> INFO sapi=0 tei=0, ns=5 nr=4
Mar 7 03:00:55.994: ISDN Se0/0/0:15 Q931: SETUP pd = 8 callref = 0x0084
Bearer Capability i = 0x8890
Standard = CCITT
Transfer Capability = Unrestricted Digital
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA9839F
Exclusive, Channel 31
Called Party Number i = 0x81, '09665484798'
Plan:ISDN, Type:Unknown
Mar 7 03:00:56.006: ISDN Se0/0/0:15 Q921: User RX <- RR sapi=0 tei=0 nr=6
Mar 7 03:00:56.018: ISDN Se0/0/0:15 Q921: User RX <- INFO sapi=0 tei=0, ns=4 nr=6
Mar 7 03:00:56.018: ISDN Se0/0/0:15 Q931: RELEASE_COMP pd = 8 callref = 0x8084
Cause i = 0x8286 - Channel unacceptable
Mar 7 03:00:56.022: ISDN Se0/0/0:15 Q921: User TX -> RR sapi=0 tei=0 nr=5
Mar 7 03:00:59.995: ISDN Se0/0/0:15 Q921: User TX -> INFO sapi=0 tei=0, ns=6 nr=5
Mar 7 03:00:59.995: ISDN Se0/0/0:15 Q931: SETUP pd = 8 callref = 0x0084
Bearer Capability i = 0x8890
Standard = CCITT
Transfer Capability = Unrestricted Digital
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA9839F
Exclusive, Channel 31
Called Party Number i = 0x81, '09665484798'
Plan:ISDN, Type:Unknown
Mar 7 03:01:00.007: ISDN Se0/0/0:15 Q921: User RX <- RR sapi=0 tei=0 nr=7
Mar 7 03:01:00.019: ISDN Se0/0/0:15 Q921: User RX <- INFO sapi=0 tei=0, ns=5 nr=7
Mar 7 03:01:00.019: ISDN Se0/0/0:15 Q931: RELEASE_COMP pd = 8 callref = 0x8084
Cause i = 0x8286 - Channel unacceptable
Mar 7 03:01:00.019: ISDN Se0/0/0:15 Q921: User TX -> RR sapi=0 tei=0 nr=6
Mar 7 03:01:03.995: ISDN Se0/0/0:15 Q921: User TX -> INFO sapi=0 tei=0, ns=7 nr=6
Mar 7 03:01:03.995: ISDN Se0/0/0:15 Q931: RELEASE_COMP pd = 8 callref = 0x0084
Cause i = 0x80E6 - Recovery on timer expiry
Mar 7 03:01:03.995: ISDN Se0/0/0:15 **ERROR**: CCPCC_CallOrigination: SETUP timed-out (2nd T303) to NETWORK. The SETUP failed.
BR ,
SANDIPAN

Similar Messages

HT201412 Safari could not open the page because the server stopped responding- new ipad mini's (2 from separate places) are not working with At & T router but computers work. Can you please help me. I've tried everything. Thanks ya'll!

Safari could not open the page on my new ipad mini's because the server stopped responding- new ipad mini's (2 from separate places) are not working with At & T router but computers work fine. Yesterday I got it to work. Weird. Can you please help me. I've tried everything. Thanks ya'll!

Hello SavannahSweetie,
I was looking into the issue you are desribing, and found a great article for troubleshooting wifi connections with iOS devices. It's called iOS: Troubleshooting Wi-Fi networks and connections and can be found here: http://support.apple.com/kb/ts1398.
Start with this section, and work your way down if needed.
Basic troubleshooting
Tap Settings > Wi-Fi and turn Wi-Fi off and then on again.
Verify that you are in range of your Wi-Fi router or base station.
Confirm that your Wi-Fi router and Cable/DSL modem are connected to power and turned on.
Check whether other devices (portable computers, for example) are able to connect to the Wi-Fi network and access the Internet.
Update your Wi-Fi router to the latest firmware.For AirPort Base Stations, refer to this article for information about firmware updates. For third-party Wi-Fi routers, check the manufacturer's website for details on updating your firmware.
Restart your iOS deviceHold the On/Off button until "slide to power off" appears. Slide to power off your device. When it is off, press the On/Off button to turn it back on.
All the best,
Sterling

Urgent--custom servlet not working with https/gateway of the portal server

We have created the custom servlet to add some more authentication to the login screen. I have explained detaildely below.
We have set if password reset change password screen should come by using identity server.
First screen comes which asks �user id� and �password�.
after this next screen comes with �old password�, �New Password� and �Confirm Password� (as we have forcefully asked user to change password after reset by using identity server ).
On this page we have added two new filed �Date of Birth� and �Date of Joining�.
And we are forcefully transferring request to our Custom Servlet which will validate the �Date of Birth� and �Date of Joining� from the database and submit the same a form as required by Login Servlet to validate the default parameters �old Password�, �New Password� and �Confirm Password� (which is the default validation without adding custom Servlet).
This whole process is working with �http� protocol and giving �unable to connect� host with �https� protocol.
Without custom Servlet process is like this, which is working
Login (usrid, password) � Login (Old Password, New Password, Confirm Password) � Portal home Page
With custom Servlet , Which is not working with �https� Protocol. we are getting the message "Authentication Failed" screen.
Login (usrid, password) --> Login (Old Password, New Password, Confirm Password , Date of Birth, Date of Joinig) --> Custom Servlet validate Date of Birth, Date of Joining --> Login (Old password, new Password, Confirm Password) --> Protal Home Page
This one works with http, whereas this one gives the "Authentication Failed" screen with the https.
Please let me know if anybody have implemented this and help me to resolve the issue.
Best Regards
Ramkumar

Hi,
I am also getting this error message in the sun ONE webserver error log file....
[20/Nov/2004:13:42:39] failure ( 6162): for host 172.16.5.21 trying to GET /amserver/UI/Login, service-j2ee reports:
StandardWrapperValve[LoginServlet]: WEB2792: Servlet.service() for servlet LoginServlet threw exception
com.iplanet.jato.CompleteRequestException
at com.sun.identity.authentication.UI.AuthenticationServletBase.onUncaughtException(AuthenticationServletBase
.java:141)
at com.iplanet.jato.ApplicationServletBase.fireUncaughtException(ApplicationServletBase.java:1023)
at com.iplanet.jato.ApplicationServletBase.processRequest(ApplicationServletBase.java:469)
at com.iplanet.jato.ApplicationServletBase.doPost(ApplicationServletBase.java:324)
at com.iplanet.jato.ApplicationServletBase.doGet(ApplicationServletBase.java:294)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:787)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:908)
at org.apache.catalina.core.StandardWrapperValve.invokeServletService(StandardWrapperValve.java:771)
at org.apache.catalina.core.StandardWrapperValve.invoke(StandardWrapperValve.java:322)
at org.apache.catalina.core.StandardPipeline.invoke(StandardPipeline.java:509)
at org.apache.catalina.core.StandardContextValve.invoke(StandardContextValve.java:212)
at org.apache.catalina.core.StandardPipeline.invoke(StandardPipeline.java:509)
at org.apache.catalina.core.StandardHostValve.invoke(StandardHostValve.java:209)
at org.apache.catalina.core.StandardPipeline.invoke(StandardPipeline.java:509)
at com.iplanet.ias.web.connector.nsapi.NSAPIProcessor.process(NSAPIProcessor.java:161)
at com.iplanet.ias.web.WebContainer.service(WebContainer.java:586)
Regards
Ramkumar R

T42 will not work with new wireless router

Purchased a new router, works great with my T61 and x200 but not with my older T42. The old router worked fine with all 3 thinkpad computers. I am told that the T42 has only an 11mps modemcard inside, and therefore I am out of luck. I have to purchase an external usb modem or slow down the router for the other machines. Is there nothing I can do with my T42 settings to get onto this new router? Steve

Posting the 7-character model number of your T42 would help a lot...
You can replace the wireless card with a newer bg or abg one, and it should work fine with a newer router.
For a list of applicable cards, look at this page under number 14:
http://www-307.ibm.com/pc/support/site.wss/document.do?sitestyle=lenovo&lndocid=MIGR-46474
Good luck.
Cheers,
George
In daily use: R60F, R500F, T61, T410
Collecting dust: T60
Enjoying retirement: A31p, T42p,
Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

Airplay not working with non-apple router

I use an airport express only for playing music in a remote location. It stopped working after I switched my main wireless router from a Time Capsule to a Linksys running Tomato USB firmware.
The Express is set up as "join a wireless network" with the correct SSID and password. The light on the Express is green and the main router status page shows it is connected, but Airplay cannot see the Express from either iTunes on my macbook or my iPhone. Also I cannot see the device in Airport Utility. When I connect the Express to my computer with ethernet, Airport Utility can see it and so can iTunes.
I have another Express hooked to the network via ethernet and everything works fine with that one.
Surely Airplay should work with non-apple wireless routers. Any suggestions would be appreciated.
thanks

Factory reset the express, and try to make it join again...

Macbook pro not working with BT infinity/ router?

Hi, well basically our family got BT infinity about 2 weeks ago, and it worked with my macbook for about 3 days or so, but after that just suddenly stopped working. It says it's connected in airport and gives full connection, but chrome, spotify, skype, etc do not work. However the rest of the computers in the house which run on windows do work. For the last week or so I have been using a neighbour's open wireless (Netgear) which has been pretty consistent if a little slow. So basically, is there anything i can do? i've pretty extensively looked at all the forums regarding MBPs and routers, and it seems it may be a mac fault (meaning i may be in the wrong forum.) but any help would be appreciated. thanks.

kategreat wrote:
Hi, well basically our family got BT infinity about 2 weeks ago, and it worked with my macbook for about 3 days or so, but after that just suddenly stopped working. It says it's connected in airport and gives full connection, but chrome, spotify, skype, etc do not work. However the rest of the computers in the house which run on windows do work. For the last week or so I have been using a neighbour's open wireless (Netgear) which has been pretty consistent if a little slow. So basically, is there anything i can do? i've pretty extensively looked at all the forums regarding MBPs and routers, and it seems it may be a mac fault (meaning i may be in the wrong forum.) but any help would be appreciated. thanks.
Hi there,
It sounds to me like you're having troubles with the wireless channels on the Home Hub.
Here's what I'd suggest you do: Download istumbler on your Mac (or inssider 2 on your PC) and use this to check which wireless channel you're currently on and if need be, change to a less congested channel.
I hope this info helps.

Down arrow not working with voice over

Hi I am speaking on behalf of someone who owns a macbook, I am quite new to mac but much pc experence so have been learning mac quickely.
However the following issue has arisen and I am unsure how to fix,
because of his needs voice over is turned on, however and has worked fine with the zoom also on.
Howver today he has pressed something and now when voice over is on the down bottom jumps between different sections on the page such as the title of the probgram and the heading and bottom of page and will not scroll bit by bit on an email/safari like it did UNLESS you turn voice over off..
any suggestions on how to resolve this would be great..
thanks all

I'm sure there's a software setting that needs to be adjusted, but I don't know Voice Over very well. Which version of OS X is on the computer? I'll ask the hosts to move this thread to the appropriate forum once you let us know
~Lyssa

Rapidshare link not working with WRT110 wireless router

I am trying to download using rapidshare but after the countdown timer reaches zero and the download link button appears, i couldn't get the link for the download file. This happens when i am wireless but when i connect my laptop directly to the linksys WRT110 router via LAN cable, i can get the link for the download file without problems.
What settings do i need to do to fix this? The rapidshare says it might be due to a rotating IP address or something. Only the rapidshare website is having this problem, other downloading sites doesn't seem to have this problem.
i am using a WRT110 router, with no security, on a wireless connection on my laptop on windows vista, using firefox.

Tried Internet Explorer 7, its the same problem. it still takes some time before i can get the link for the download file. Although i sometimes can get it faster with IE than with firefox.
Any solutions to this problem? I still thinking its the Routers configuration that has to be modified to solve this problem.

AirMac Extreme and Airport Express not working with Netgear N Router?

I've been using an AirMac Extreme (old model) as a wireless router, and Airport Express for it's airtunes functionality (conected to my Hi-Fi).
These used to work fine, and both would show up in my Airport Utility on my Macs.
I've now just upgraded to a 50MG broadband contract, and the engineer gave me a Network router as my old AirMac Extreme couldn't handle that bandwidth.
When I connected my AirMac Extreme to my Netgear router I then got conflicts, sometimes it wouldn't show up, and it really slowed down my wireless signal. As a result the contractor for my broadband recommended I disconnect my Air Mac Extreme from the router. Speeds went up for the internet, but now I can't get my airtunes to work.
What I want to know is can I just use my Netgear to transmit the broadband signal so I get maximum internet speeds, but then have my AirMac Extreme and Airport Express connected so that I can still listen to my itunes wirelessly?
Ideally I'd like this to all be set up so that I could be conected to the internet through the Netgear wirelessly and listen to my itunes through the Airport Express at the same time.
Thanks in advance for any advice.

I am sorry that I don't have a definitive answer but I also have Windows computers and I have "inherited" some older Apple devices from my son and am trying to learn about them so in addition to searching this group, I "Googled" "1st generation airport express" and it listed many specific posts in this group - I read them all and they might answer your question - good luck

Why does my mac not work with cisco E3000 router

It says that it needs os x 10.6.1 or later and I have that and its not working

Ask Cisco, but:
Internet Quick Assist:
http://support.apple.com/kb/HT1144?viewlocale=en_US
Troubleshooting internet settings:
http://support.apple.com/kb/HT1714?viewlocale=en_US

Printer not working with new router

I have a new router and my laptop with Windows XP is working Ok
My printer Deskjet 3520 network test result shows successful setup But it does not print when laptop requests
What can I do

Hi @Jobrig,
Welcome to the HP Forums!
I see that your HP Deskjet 3520 is not working with your new router, and I am happy to help with this connection issue!
For further assistance, I will need to know: if you are using a Windows or Mac Operating System, and the version number. To find the exact version, visit this link. Whatsmyos, and if the printer is able to make copies.
In the meantime, please see the following:
This printing guide, Print Jobs are Stuck in the Print Queue.
This website, HP Wireless Printing Center, may also help.
Hope these guides will help you, and thank you for posting!
RnRMusicMan
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to say “Thanks” for helping!

Hp Photosmart not working with new router

My Hp Photosmart D110a will not work wirelessly with my new Netgear N600 router. This is the second new router I have tried. With the first one Belkin I could at least get it to print from my PCs. But never with my IPad. Now the printer will not print from anything. I have reset it, entered new passwords etc. spent hours on the phone with tech support. What to do now?

@Ann99, welcome to the forums
I understand your Photosmart D110a model is not working with your new router. I will gladly do my best to help you.
I have some questions and some things for you to try.
1. Is the printer connecting to the wireless network successfully when you run the wireless setup wizard from the printers front panel or is the printer not found when you are running the installation from your PC?
2. What did tech support determine the issue was when you called them?
3. Here are some guides for you to try, these 2 guides relate to the questions I had asked in the first question:
Unable to Connect to a Wireless Network When Using WEP Encryption and Shared Key Authentication
The Printer Is Not Found During a Wireless Network Installation
4. What Operating System are you running on your computer?
5. Where are you running the installation from (disk, download or HP Printer Install Wizard for Windows for Windows)?
Please let me know all of the information and results from your troubleshooting above!
Have a terrific day
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

Photosmart C4780 won't work with my new router.

Hi
I have been sent a new plusnet TG582n router after my old one broke and now my wireless printer won't work.
I have tried uninstalling the software and connecting the printer via USB to reinstall on my windows 7 netbook but it came up with drivers failed to install.
On my windows 8.1 laptop I have uninstalled and reinstalled and this was unable to complete. I have now done a restore to a previous setting on both of them so the software and drivers are still on.
I have tried connecting my printer via USB cable but this tries to install the software again.
If I go into devices my printer shows up with error and won't print.
After trying all this I have now done a restore on the printer to factore settings (also trying the uninstall and reinstall via USB after this) and it still won't work.
After doing a wireless test report it came up with my old ssid initially even after installing my new router which has a new ssid. After resetting the printer it now comes up with SigmaplusEOL1. It shows on the report that wirelss is on and working but ssid fail.
I don't know what else to try as I have spent hours tyring different things and done trouble shooting several times.
I have also been told by plusnet that t he routershould work for wireless n or wireless g.
Please help!

Hi Tazza,
Welcome to the HP Forums! I understand that your HP Photosmart C4780, will not work with your new router. I am happy to help you with this! I believe these following guides should help:
The Printer is Not Found During Wireless Network Installation in Windows.
Printer Does Not Maintain Wireless Connection.
Just to make sure the hardware is functional, can you make copies standalone with the printer? Or what happens when you print a status report? Video of Printing a status report.
Hope to hear from you, and thank you for posting!
RnRMusicMan
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to say “Thanks” for helping!

Voice Memo is not working with iOS 8.2

Voice Memo Records is not working with iOS 8.2. how to fix it?

Voice Memo Records is not working with iOS 8.2. how to fix it?

My itunes 11 Home sharing is not working with my windows 7 PC and iPad it shows up on iPad and when I go to share the music app does loading for 3 mins and crashes I am using a virgin super hub router please please please help

My itunes 11 Home sharing is not working with my windows 7 PC and iPad it shows up on iPad and when I go to share the music app does loading for 3 mins and crashes I am using a virgin super hub router please please please help

My itunes 11 Home sharing is not working with my windows 7 PC and iPad it shows up on iPad and when I go to share the music app does loading for 3 mins and crashes I am using a virgin super hub router please please please help

Standby PRI not working with voice Gateway Router & CUCM

Similar Messages

Maybe you are looking for